User manual COBRA ESD6000

ESD-6000.MANUAL.qx 11/13/97 10:26 AM Page 1 Installing and Using Your 1. What You'll Need To Install The ESD-6000: NOTE: Detailed instructions on opposite side 3. Operating The ESD-6000: A. Turn On and Adjust Volume E. Indicators and Visual Alerts Power DETECTION SYSTEM Model ESD TM-6000 LEDs are briefly illuminated at Power ON Illuminates when On X Band Radar Blinks faster as source approaches Turn on sequentially as source approaches B. Set Display Brightness NORMAL ESD-6000 Windshield Bracket Hook and Loop Material (For on-dash mounting) Power Cord K and Ka Band Radar 2. Installing The ESD-6000: U.S. Patent No. 5,497,148 NEED HELP? C. Set City/Highway Mode ± LOW Laser OFF Blinks faster as source approaches Turn on sequentially as source approaches ON WINDSHIELD ON DASH Blinks at a steady rate Both turn on ATTACH CUPS TO BRACKET PEEL PROTECTIVE PAPER OFF ONE SIDE OF HOOK AND LOOP ATTACH BRACKET TO WINDSHIELD PLACE ON DASH ± ATTACH DETECTOR TO BRACKET PEEL TOP PAPER OFF CITY: For urban driving-reduces number of X-Band false audible alerts. HIGHWAY: For all other driving. VG-2 Blinks at a steady rate Safety Alert® Traffic Warning System Cobra Electronics Corporation 6500 West Cortland Street, Chicago, Illinois 60707 BEND BRACKET FOR CORRECT DETECTION ANGLE (IF NEEDED) PLACE DETECTOR ON HOOK AND LOOP PAD D. Muting All Flash City/Highway Mode PLUG POWER CORD INTO DETECTOR POWER CORD INTO DETECTOR ± PRINTED IN KOREA ©1997 COBRA ELECTRONICS CORPORATION 480-260-P-001 PLUG POWER CORD INTO CIGARETTE LIGHTER PLUG POWER CORD INTO CIGARETTE LIGHTER Press to reduce volume of audible alert in progress. Illuminates in CITY mode ESD-6000.MANUAL.qx 11/13/97 10:26 AM Page 2 Congratulations! I. Introduction You have just purchased the most sophisticated RADAR/LASER DETECTOR available today. This booklet contains instructions and information designed so that you will be able to understand how the Cobra ESDTM-6000 works and how radar and (LIDAR) laser are used. Enjoy your Cobra ESD-6000 Radar/Laser Detector and DRIVE SAFELY. Federal Law Governing Use of Radar Detectors It is not against Federal Law to receive radar transmissions on your COBRA Radar Detector. The Communications Act of 1934 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene the Communications Act of 1934, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by Federal Court action. WARNING: Before leaving your car, make sure that you conceal your radar detector. This will reduce the possibility of break-in and theft of your unit. Use of this product is not intended to, and does not, ensure that the motorist and any passenger will not be involved in a traffic accident. It is only intended to alert the motorist that an emergency or service vehicle equipped with a CODE 3 or Cobra Safety Alert Transmitter is in the area as defined by the range of the product. Motorists are expected to exercise all due caution while using this product, and to observe and follow all applicable traffic laws. Operators of emergency or service vehicles are also expected to exercise all due caution while using this product, and to observe and follow all applicable traffic laws. A. Location Selecting the proper location to mount the Cobra ESD-6000 is very important for optimum performance. Both radar and laser transmissions pass through glass but not through other objects. For this reason the Cobra ESD-6000 lens must not be blocked. It is best to locate your detector in the middle of the front windshield. Examples of metal in the windshield area that can block or weaken incoming radar/laser signals: 1. Windshield wiper blades. Mount your Cobra ESD-6000 so that it will NOT be behind the blades when they are at rest. 2. Mirrored sun screens. It is recommended that sun screens be removed, or they may impair the performance of your Cobra ESD-6000 by acting as an impenetrable barrier to radar/laser signals. 3. Regular tinted glass does not affect radar reception, although the darker tint at the top of the tinted windshield prevents laser light from penetrating. 4. Heated windshields, currently available as an option for some Ford® (Instaclear) and GM® (Electriclear) vehicles act as an impenetrable barrier to radar signals. (If in doubt, check with your dealer to see if this applies to your vehicle). B. Mounting 1. Windshield Mounting The WINDSHIELD MOUNTING BRACKET offers convenient mounting to windshields and provides for easy movement of detector between vehicles. Note: Some new vehicles have a soft plastic coating on the inside surface of the windshield. Suction cups can permanently mark this "anti-lacerative" coating. Check with your owner's manual to see if this applies to your vehicle. a. Assemble suction cup on bracket by putting round "buttons" through larger holes in the bracket and pressing them toward the outside edges until they snap into position. b. Install bracket to detector: align bracket with slot on rear of detector and slide bracket into opening. To remove bracket from detector, simply pull bracket out of slot. II. Installation c. Mounting on Windshield To install the Cobra ESD-6000 onto the windshield, simply press it firmly on to the glass. Sometimes the suction cups adhere better if they are slightly moistened. In cold weather, you may need to warm the suction cups before application. d. Adjustment If necessary to achieve correct angle,remove the detector from the bracket and the bracket from the windshield. Adjust the bracket by bending it. DO NOT BEND THE BRACKET USING THE ESD-6000 AS A LEVER. e. Removal To remove the Cobra ESD-6000 from your windshield, release each suction cup by lifting one edge with your finger, or by pulling on tab. 2. Dashboard Mounting Mounting your ESD-6000 to the dashboard of your vehicle requires a clear, level unobstructed view of the road for the detector, without blocking the driver's vision. Select a mounting position that allows the detector to have a clear view of the road ahead. Using the hook and loop material provided, proceed as follows: (See illustration on reverse side) a. Remove backing from one side and apply to dash. b. Clean dashboard with common rubbing alcohol to remove dirt and grease. Remove backing from other side and place detector on top. Let adhesive set. Note: With this hook and loop material dashboard mounting, it's easy for you to remove and reinstall your Cobra ESD-6000 detector at any time. Remember: Without means to adjust the angle of the detector (when mounted as above), be sure you that your Cobra ESD-6000 has a level, clear view of the road before you attach the hook and loop material. III. Operation A. Band Detection This detector is designed to detect X, K, Superwide Ka Band Radar, Laser, VG-2, and Safety Alert signals. B. Signal Strength Meter The Signal Strength Meter on your detector indicates relative range. The meter is made up of the Visual Alarm Indicators (see section I) for low level radar/laser signals and the Signal Strength LEDs for stronger signals. C. Audible Alarm Indicator A different alert tone will sound for X, K, Ka, Laser, VG-2 and Safety signals. These sounds are demonstrated during the power-on sequence each time you turn your Cobra ESD-6000 on. D. Instant-on Detection The Cobra ESD-6000 is also designed to detect Instant-on speed monitoring signals. Immediate action is required when warning is given. E. Power/Volume Control Plug the Cobra ESD-6000 power adapter cord into POWER connector. Insert other end into cigarette lighter of the vehicle. The POWER/VOLUME CONTROLon the left side of the Cobra ESD-6000 controls power and regulates the audible alert volume. To turn on, turn the thumbwheel away from you. Each time the unit is turned on, an automatic test pattern takes place: · This pattern consists of the Alarm Indicators and SIGNAL STRENGTH METER illuminating in unison with the audio alarm for two seconds. · The green POWER LED remains illuminated after the test sequence is completed. F. VG-2 Undetectable Some states or municipalities use devices referred to as "VG-2". The VG-2 device detects low level energy radiated by the internal oscillators of radar detectors. The VG-2 device also radiates a similar type of energy. The ESD-6000 detects the VG-2's radiation before the VG-2 can detect the ESD-6000. The ESD-6000 then briefly turns off its internal oscillator, rendering it invisible to the VG-2, and alerts you to VG-2's presence. During these short intervals, the ESD-6000 is not able to receive radar or Safety Alert signals (laser reception is not affected). Once past the VG-2, the ESD-6000 returns to normal operation. G. Band Alarm Indicators When the Cobra ESD-6000 detects an X-band radar signal, the red "X" Visual Alarm Indicator (LED) will flash in unison with the X-Band audio tone. When the ESD-6000 detects either a K-band or a Ka-band radar signal, the amber "K/Ka" Visual Alarm Indicator will flash in unison with the K or Ka Band audio tone. When the ESD-6000 detects pulses of laser light, the yellow "L" LED will flash in unison with the Laser tone. When VG-2 is detected, the amber "VG-2" LED will flash with an audio tone. When a Safety Alert signal is detected, all LEDs except POWER will flash. H. Mute Button The mute function is controlled by a momentary button. Pressing MUTE will eliminate the audio during the alert in progress. The detector will automatically reset to normal operation after the alert has passed. It will also reset to normal any time the detector is turned off. I. City/Highway The Highway/City function is controlled by a 2-step momentary button. The Highway mode is automatically engaged when the unit is powered up. To engage City Mode, press down on the Highway/City button. A green LED will light to indicate that the detector is in City Mode. To reactivate the Highway Mode simply press down on the Highway/City button again. The green LED will go dark to indicate that the detector is in Highway Mode. In the Highway Mode, your Cobra ESD-6000 operates at full sensitivity on all three radar bands plus laser. In the City Mode, the X-band audio alert sensitivity is lowered to reduce false alerts. In or near cities, there are many sources of false radar signals. Microwave relay towers for telephone and TV signaling, anti-shoplifting systems and bank alarms­all are examples of false X-band sources. K. Dim Button You may select from three levels of brightness for your Cobra ESD-6000 display: Normal, Low, and Dark. Each time you turn your ESD-6000 on, the display is automatically set to full brightness. Pressing once on the Dim Button reduces the display brightness to Low; pressing a second time turns the display off; pressing a third time returns the display to Normal. COBRA RADAR DETECTOR ACCESSORIES Description STRAIGHT DC POWER CORD Including plug/fuse for ESD-6000 Part No. 420-080-N-001 420-080-N-002 Cost Ea. $10.00 $10.00 X Qty. = Amount IV. Detection Alert A. Radar/VG-2/Laser Alerts Type of Audible Signal Your COBRAESD-6000 starts to signal slowly, then increases in rate very rapidly. Your COBRAESD-6000 signals just once. Very fast signal rate instantly. Slow signal rate as you approach hill or bridge. Sharp increase in signal rate as you reach hill or bridge. Short-term, weak signaling; series of such signals. Laser "chirps." Interpretation and Response Most likely police radar. FULLALERT. Most likely a false source, or could be pulsed radar. EXERCISE CAUTION. Radar or VG-2 close by has been suddenly switched on. FULLALERT. Most likely police radar on other side of hill or bridge. FULLALERT. Most likely a false radar source. EXERCISE CAUTION. Take FULLCAUTION. There are no false laser signals. An emergency vehicle is in the vicinity, you are in the vicinity of a railroad crossing, or you are approaching a road hazard (construction site, accident scene, etc.) . Radar Frequencies There are now three frequencies that have been approved by the FCC (Federal Communications Commission) for use in speed monitoring equipment. They are: X Band (10.525 GHz), K Band (24.150 GHz), Ka Band (33.400--36.000 GHz) Your Cobra ESD-6000 can detect signals in all three bands including photo radar and STALKER radar which use the Ka band, Cobra Safety Alert signals on the K band, VG-2 and laser. D. Facts About LIDAR (Laser) · What is LIDAR? LIDAR stands for Light Detection And Ranging. While everyone refers to it as LASER the correct name is LIDAR. · How does LIDAR work? LIDAR operates a lot like RADAR. Like RADAR, it spreads out. Not as quickly, but it does spread, as shown on the diagram below. C. V. Maintenance Your COBRAESD-6000 RADAR/LASER DETECTOR will give you years of trouble-free service with minimum maintenance. Replacing Power Cord Fuse Unscrew cap of cigarette lighter adapter and remove fuse. Replace with 1-ampere fuse only. Troubleshooting If your COBRALASER DETECTOR ESD-6000 isn't operating, we suggest you make the following checks: 1. Is the power cord properly connected? 2. Is the fuse OK? 3. Is the cigarette lighter socket clean and free from corrosion? CURLED TYPE POWER CORD For ESD-6000 For technical assistance, please call our Automated Help Desk which can assist you by answering the most frequently asked questions about Cobra products. WINDSHIELD MOUNTING BRACKET (Prices subject to change without notice.) 545-139-N-001 $7.00 (773) 889-3087 24 hours a day, 7 days a week. A Consumer Service Representative can be reached through this same number 8:00 am - 8:00 pm, Monday through Friday, CST. Technical assistance is also available on-line in the Frequently Asked Question (FAQ) section at www.cobraelec.com or by e-mail to productinfo@cobraelec.com 55 Illinois residents add 7% 55 Cook County, ILresidents additional .75% (7.75% total) 55 Chicago, ILresidents additional 1% (8.75% total) 55 Indiana residents add 5% 55 Michigan residents add 6 % 55 Ohio residents add 6% 55 Wisconsin residents add appropriate % Amount __________ (Tax if applicable@@) __________ Shipping/handling Total @ $3.75 __________ Limited One Year Warranty COBRA ELECTRONICS CORPORATION warrants that its COBRAradar detectors, and the component parts thereof, will be free of defects in workmanship and materials for a period of one (1) year from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U.S.A. COBRA will, without charge, repair or replace, at its option, defective radar detectors, products or component parts upon delivery to the COBRAfactory Service Department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt. You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Cobra's expense, if the product is repaired or replaced under warranty. For further details concerning procedures for obtaining service, see the "If You Think You Need Service" section of the Owner's Manual. Exclusions: This limited warranty does not apply; 1) to any product damaged by accident; 2) in the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs; 3) if the serial number has been altered, defaced or removed; 4) if the owner of the product resides outside the U.S.A. All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty. COBRA shall not be liable for any incidental, consequential or other damages; including, without limitation, damages resulting from loss of use or cost of installation. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. COBRA ELECTRONICS CORPORATION 6500 W. Cortland Street, Chicago, Illinois 60707 If You Think You Need Service, Call 773-889-3087 If your product should require factory service please call Cobra first before sending your unit in. This will ensure the fastest turnaround time on your repair. You may be asked to send your unit to the Cobra factory. It will be necessary to furnish the following, in order to have the product serviced and returned. 1. For Warranty Repair, include some form of proof-of-purchase, such as a mechanical reproduction or carbon or sales receipt. If you send the original receipt it cannot be returned. 2. Send the entire product. For example­must include detector, bracket with suction cups, and cord. 3. Enclose a description of what is happening with the unit. Include a typed or clearly printed name and address of where the unit is to be returned. 4. Pack unit securely to prevent damage in transit. If possible, use the original packing material. 5. Ship prepaid and insured by way of a traceable carrier (to avoid loss in transit) such as United Parcel Service (UPS), Roadway Parcel Service (RPS), or First Class Insured Mail to Cobra Factory Service, Cobra Electronics Corporation, 6500 W. Cortland St., Chicago, IL 60707. Cobra is not responsible for units not received if package has not been properly insured. 6. If the unit is in warranty, upon receipt of your unit it will either be repaired or exchanged depending on the model. Please allow approximately 3 to 4 weeks before contacting us for status. If the unit is out of warranty a letter will automatically be sent informing you of the repair charge or replacement charge. If you have any questions, please call 773-889-3087 for assistance. Make check or money order (no stamps) payable to Cobra Electronics and mail with this order form to: Cobra Accessories Dept. 6500 W. Cortland St., Chicago, IL 60707 Call 773-889-3087, or fax 773-622-2269 for credit card orders Allow 4 to 6 weeks for delivery. Offer valid in Continental U.S. only. Please print clearly: Name __________________________________________________________________ All Band Indicators illuminate,ESD-6000 double "braps" rapidly. B. Facts About the Safety Alert ®Traffic Warning System FCC-approved Safety Alert Transmitters emit microwave radar signals to indicate the presence of a safety-related concern. Depending on the frequency of these signals, as set on the transmitter, the outgoing signal can indicate whether the transmitter is on a speeding emergency vehicle or train, or at a stationary road hazard location. These microwave signals are located in the K-band and as a result, any radar detector which detects K-band radar will detect these Safety signals as standard K-band radar alerts. However, unlike a standard radar detector, your Cobra ESD-6000 is designed to differentiate between a standard K-band alert and a Safety Alert. Since Safety technology is relatively new and the number of transmitters in operation is not yet widespread, you may not receive Safety alerts on a daily basis and should not be surprised to encounter some emergency vehicles, road hazards and trains that are not yet equipped with these transmitters and therefore fail to provide a signal. As Safety transmitters become more prevalent (the number of operating transmitters is growing every day), these Safety Alerts will become more common. LIDARs must have a clear line of sight to target a vehicle during the entire measurement interval. Intervening objects such as signposts, utility poles, tree branches, etc., will prevent a valid speed reading. · Does weather have any effect on LIDAR? Yes, rain, snow, smoke, fog, and airborne dust particles will all reduce the effective range, and if sufficiently dense, may prevent its operation. · Can LIDAR operate through glass? No, LIDAR guns cannot obtain readings through any glass. But the laser pulse can be received through glass to easily and quickly trigger a laser detector's alarm. · Can LIDAR operate while moving? No, since LIDAR is line of sight, an officer cannot drive, aim, and shoot while driving. · Is a LIDAR DETECTOR legal to use? Yes, it is legal in all 50 states. Address (Not P. O. Box) ____________________________________________________ City ________________________________State____________Zip ________________ Telephone No. (________) ________________________________________________ Credit Card No.______________________________________Exp. Date ____________ Customer Signature __________________________________________ Circle One: Visa MasterCard Discover Allow 4 to 6 weeks delivery. Offer valid in Continental U.S. only.