Two-Way Radio Model MT 600 ENGLISH 1. Antenna 2. External Speaker/ Microphone/Charge Jack 3. Mode/Power Button 4. Lock Button 5. Channel Select Buttons 6. Speaker/Microphone 7. Light/Max Range Button 8. Volume Control Buttons 9. Talk Button 10. Call Button 11. Belt Clip 12. Battery Compartment 13. Lock Tab 1 2 10 9 3 4 5 8 7 11 6 12 13 Printed in China Part No. 480-329-P Version A PRODUCT FEATURES Features · Two-Way Radio with up to a 5 km (3 mile) range · 8 Channels* · 38 CTCSS Privacy Codes · 83 DCS Privacy Codes · Backlit LCD Display · Battery Saver Circuitry · Maximum Range Extender · Call Alert (5 selectable tones) · Scan (Channel, Privacy Codes) · Vox Mode for Hands-Free Operation · Auto Squelch · Selectable On/Off "Roger Beep" Confirmation Tone · Key Lock · External Speaker/Microphone/Charge Jack · Belt Clip *You are not allowed to use channels 1 and 2 in France. This situation can change; please contact the French radio licensing authority for more information. 1 2 3 English 4 11 5 6 7 10 9 8 1. 2. 3. 4. 5. 6. Scan Icon Roger Beep Icon DCS Icon Lock Icon VOX Icon CTCSS Icon 7. Battery Low Icon 8. Privacy Code Numbers 9. Power Saver Icon 10. Main Channel Number 11. Receive/Transmit Icon Product Information This microTALK® radio has been manufactured to meet all required standards for radio equipment using PMR 446 frequencies as authorized. The use of this two-way radio product involves the public airways and its use may be subject to local laws or regulations. Contact your radio licensing authority for more information. Caring for Your Radio Your microTALK® radio will give you years of trouble-free service if cared for properly. Here are a few suggestions: · Handle the radio gently. · Keep it away from dust. · Never put the radio in water or in a damp place. · Avoid exposure to extreme temperatures. OPERATION Charger and Rechargeable Batteries Remove Belt Clip Lock Tab English Insert Batteries To Insert Batteries in Radio: 1. Remove belt clip by releasing belt clip latch and sliding clip up. 2. Push up on lock tab to remove battery cover. 3. Insert batteries according to polarity markings. NOTE: Estimated operation time on full charge: 12 hours. These rechargeable batteries must be recycled or disposed of properly in compliance with all applicable laws. They must not be thrown in the rubbish bin. Some countries and local authorities require recycling and have established collection programs. Please contact your local waste disposal authority for instructions. WARNING: Do not put batteries into fire or expose to high heat. They may explode. For Charging Cobra's microTALK® Radio(s): Wall Charger 1. Check to see that the batteries have been inserted properly. See above for battery installation instructions. 2. Insert round connector of wall charger into the charge jack located at the top of the radio. The wall charger has two (2) round connectors which enables you to charge either one (1) or two (2) radios at a time. 3. Plug the wall charger into electrical outlet. It is not recommended to recharge batteries more than 24 hours. Estimated operation time on a full charge is 12 hours. Insert Connector Use only the supplied rechargeable batteries and wall charger for recharging your Cobra microTALK® radio. Non-rechargeable alkaline batteries can also be used. Radio Power To Turn Your Radio On: ­ Press and hold the MODE/POWER button until you hear a series of audible tones indicating that the radio is On. Your microTALK® radio is now in LISTENING MODE, ready to receive transmissions. The radio is always in LISTENING MODE, except when the TALK, CALL or MODE/POWER buttons are pressed. To Turn Your Radio Off: ­ Press and hold the MODE/POWER button for two (2) seconds. Mode/Power Button Battery Low Icon Battery Low Indicator When battery power is low, the BATTERY LOW indicator will blink, indicating that batteries should be recharged or replaced. WARNING: Only the supplied NiMH batteries can be recharged. Power Saver Icon Battery/Power Saver If there are no transmissions within 10 seconds, the unit will automatically switch to Battery Save mode and POWER SAVER will appear in the display. This will not affect the unit's ability to receive incoming transmissions. OPERATION Communicating with Another Person 1. Press and hold the TALK button. 2. With the microphone about 5 cm (2 inches) from your mouth, speak in a normal voice. 3. Release the button when you have finished talking and listen for a response. You cannot receive incoming calls while pressing the TALK button. NOTE: Both radios must be tuned to the same channel and privacy code to communicate. Talk Button English 5 cm (2 Inches) From Mouth Listening for a Response ­ Release the TALK button to receive incoming transmissions. Your microTALK® is always in LISTENING MODE while the TALK or CALL buttons are not pressed. Volume Buttons Volume Level Listening To Adjust Volume ­ Press the VOLUME UP or the VOLUME DOWN buttons. A dual beep sound is used to indicate that you have reached the minimum (1) or maximum (8) volume level. Call Button ­ Press and release the CALL button. The other person will hear a two (2) second ringing tone. You cannot send or receive transmissions during the two (2) second call tone. NOTE: Both radios must be tuned to the same channel and privacy code to communicate. Channel Buttons Channels Call Button To Select a Channel ­ With the radio on, select any of the eight (8) channels by pushing the CHANNEL UP or CHANNEL DOWN button. You can press and hold the CHANNEL UP or CHANNEL DOWN button for fast advance. NOTE: Both radios must be tuned to the same channel and privacy code (see "CTCSS Privacy Codes" or "DCS Privacy Codes") to communicate. Lock Function The LOCK button locks the CHANNEL UP, CHANNEL DOWN and MODE/POWER buttons to prevent accidental operation. To Use the Lock Function: ­ Press and hold the LOCK button for two (2) seconds to turn the Lock On or Off. A double beep sound is used to confirm your Lock On or Off request. When the radio is in Lock Mode, the Lock icon will be displayed. Lock Button Lock Icon OPERATION To Illuminate Display ­ Press and release the LIGHT/MAX RANGE button to illuminate the display for 10 seconds. English Light/Max Range Button Auto Squelch/Maximum Range Extender Your microTALK® radio is equipped with Auto Squelch, which automatically shuts off weak transmissions and unwanted noise resulting from terrain, conditions or from reaching your maximum range limit. You can temporarily turn Off Auto Squelch or turn On Maximum Range Extender, allowing all signals to be received and extending the maximum range of your radio. To Temporarily Turn Off Auto Squelch: Light/Max Range Button ­ Press the LIGHT/MAX RANGE button for less than five (5) seconds. If you hear two (2) beeps, you have turned the Maximum Range Extender On (see below). To Turn Maximum Range Extender On: ­ Press and hold the LIGHT/MAX RANGE button for at least five (5) seconds until you hear two (2) beeps, indicating that the Maximum Range Extender is On. To Turn Maximum Range Extender Off: ­ Press and release the LIGHT/MAX RANGE button or change channels. microTALK® Range Your microTALK® radio has a range of up to 5 kilometres (3 miles). Your range will vary depending on terrain and conditions. In flat, open country, your radio will operate at maximum range. Buildings and foliage in the path of the signal can reduce the range. Dense foliage and hilly terrain will further reduce the signal. Remember, you can achieve maximum range by using Maximum Range Extender. See above for details. External Speaker Microphone/ Charge Jack Maximum Range Reduced Range Reduced Range External Speaker/Microphone/Charge Jack Your microTALK® radio can be fitted with an optional external speaker/microphone (not included), freeing your hands for other tasks. To Attach the External Speaker/Microphone or Charger: 1. Open the charge tab on top of the radio. 2. Insert the plug into the jack. MODE FUNCTIONS OPERATION Scrolling Through the Mode Functions English By scrolling through the Mode Functions, you will be able to select or change preferred features of your microTALK® radio. While you are scrolling through the Mode Functions, your radio features will be displayed in the same predetermined order: Set CTCSS Privacy Codes Set DCS Privacy Codes Set VOX On/Off Set VOX Sensitivity Level Set Channel Scan Set CTCSS Privacy Code Scan Set DCS Privacy Code Scan Set Call Tones Set "Roger Beep" On/Off CTCSS Privacy Codes CTCSS (Continuous Tone Coded Squelch System) is an advanced tone coding system allowing you to select one of 38 privacy codes to reduce incoming transmissions from other users on the channel. NOTE: If you are using a privacy code, both radios must be tuned to the same channel and privacy code to communicate. Each channel will remember the last privacy code you selected. To Select a CTCSS Privacy Code: 1. After selecting a channel, press and release the MODE button until the CTCSS icon flashes on the display. In addition to the CTCSS icon, either OFF or the small numbers next to the channel number will flash on the display. 2. If CTCSS and OFF are flashing, press the CHANNEL UP or CHANNEL DOWN button to exit OFF and proceed to select a privacy code; or, if CTCSS and the small numbers next to the channel number are flashing, press the CHANNEL UP or CHANNEL DOWN button to select a privacy code. 3. When your desired privacy code is displayed, choose one of the following: a. Press the MODE button to enter the new setting and proceed to other functions. b. Press the LOCK button to enter the new setting and return to LISTENING MODE. c. Do not press any buttons for 15 seconds to enter the new setting and return to LISTENING MODE. Mode Button CTCSS OFF Select Privacy Code Channel Buttons MODE FUNCTIONS OPERATION DCS Privacy Codes DCS (Digital Coded Squelch) is an advanced digital coding system allowing you to select one of 83 privacy codes to reduce incoming transmissions from other users on the channel. NOTE: If you are using a DCS code, both radios must be turned to the same channel and DCS privacy code to communicate. Each channel will remember the last code you selected. To Select a DCS Privacy Code: 1. After selecting a channel, press and release the MODE button until the DCS icon flashes on the display. In addition to the DCS icon, either OFF or the small numbers next to the channel number will flash on the display. 2. If DCS and OFF are flashing, press the CHANNEL UP or CHANNEL DOWN button to exit OFF and proceed to select a privacy code; or, if DCS and the small numbers next to the channel number are flashing, press the CHANNEL UP or CHANNEL DOWN button to select a privacy code. 3. When your desired privacy code is displayed, choose one of the following: a. Press the MODE button to enter the new setting and proceed to other functions. b. Press the LOCK button to enter the new setting and return to LISTENING MODE. c. Do not press any buttons for 15 seconds to enter the new setting and return to LISTENING MODE. Mode Button Select VOX Channel Buttons Mode Button English DCS OFF Select Privacy Code Channel Buttons Voice Activated Transmit (VOX) In VOX Mode, your microTALK® radio can be used "hands-free," automatically transmitting when you speak. You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise. To Turn VOX Mode On or Off: 1. Press the MODE button until the VOX icon flashes on the display. The current On or Off setting is displayed. 2. Press the CHANNEL UP or CHANNEL DOWN button to turn VOX On or Off. 3. When your desired VOX Mode setting is displayed, choose one of the following: a. Press the MODE button to enter the new setting and proceed to other functions. b. Press the LOCK button to enter the new setting and return to LISTENING MODE. c. Do not press any buttons for 15 seconds to enter the new setting and return to LISTENING MODE. MODE FUNCTIONS OPERATION Mode Button Select VOX Sensitivity Level Channel Buttons English To Set the VOX Sensitivity Level: 1. Press the MODE button until the VOX icon flashes and the current sensitivity level is displayed. The current sensitivity level is displayed with the letter "L" and a number 1 to 5, 5 being the most sensitive level and 1 being the least sensitive level. 2. Press the CHANNEL UP or CHANNEL DOWN button to change the setting. 3. When your desired VOX sensitivity level is displayed, choose one of the following: a. Press the MODE button to enter the new setting and proceed to other functions. b. Press the LOCK button to enter the new setting and return to LISTENING MODE. c. Do not press any buttons for 15 seconds to enter the new setting and return to LISTENING MODE. Channel Scan Mode Button Select Scan Channels Your microTALK® radio can automatically scan channels (1 to 8). NOTE: ...