User manual COBRA XRS R9G

IntelliLinkTM Wireless Remote Series 12-BandTM S-XRSTM Maximum Performance Digital Radar/Laser Detector with Red Light/Speed Camera GPS Locator* Introduction Important Information and Customer Assistance · Important Information Safe Driving Motorists are expected to exercise all due caution while using this product, and to obey all applicable traffic laws. Do not attempt to change settings of the unit while the car is in motion. Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra® radar/laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Safety/Strobe Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. It is only intended to alert the motorist that an emergency vehicle equipped with a Cobra Safety Alert, 3M or Tomar strobe transmitter is within range as defined by that product. Please call local fire and police departments to learn if coverage exists in your area. Some states and municipalities prohibit mounting any object on your windshield. If you drive in these states or areas; you can mount the MDU on the dash. Security of Your Vehicle Before leaving your vehicle, always remember to conceal your Remote Display Unit (RDU) in order to reduce the possibility of break-in and theft. Your Main Detector Unit (MDU) has a two-position bracket that, when in the up position, presents a very discreet profile from outside the vehicle. Customer Assistance Customer Assistance Use your owner's manual to learn about product features. Cobra Electronics offers the following customer assistance services: For Assistance in the U.S.A. Automated Help Desk, English only. 24 hours a day, 7 days a week 773-889-3087. Customer Assistance Operators, English and Spanish, 8:00 am to 6:00 p.m. Central Time Mon. through Fri. (except holidays) 773-889-3087. Questions, English and Spanish, Fax: 773-622-2269. Technical Assistance, English only, www.cobra.com. English and Spanish e-mail, Product info@cobra.com. For Assistance Outside the U.S.A. Contact Your Local Dealer · ©2007 Cobra Electronics CorporationTM 6500 West Cortland Street Chicago, Illinois 60707 USA www.cobra.com A1 English Introduction Controls, Indicators and Connections The XRS R7 provides detection capabilities for radar, laser and strobe signals. The XRS R9G has all the features of the XRS R7 plus a GPSL module which provides alerts when approaching photo-enforced intersections and roads with fixed red light/speed cameras. The XRS R9G can store up to 1,000 additional user-programmable Location Alerts. IntelliLinkTM Remote Display Unit (RDU) Full-Color Extreme Bright DataGrafixTM Display Main Detector Unit (MDU) Power Button Two-Piece, Self-Adhesive Fasteners Speaker GPSL Connector 12V Power Connector USB Power Connector for Recharging Battery Optional GPSL for Model XRS R7 and Standard on Model XRS R9G Global Positioning System Locator (GPSL) IS CE TH FA DS RR UA SWY K TO S MDU Connector GPSL Cable A2 English Introduction In This Package · 12V Power Cord with In-line Fuse and Cigarette Lighter Plug In This Package 12V Power Cord with In-line Fuse for Hardwired Installation 12V to 5V USB Power Adapter USB to Mini-USB Retractable Cable RDU Holster and Vent/Visor Clips GPSL Cable (R9G Only) Optional Hook and Loop Strips for Mounting Holster MDU Power Cord Clips and Pre-cut Adhesive Tapes Nothing Comes Close to a Cobra® A3 Introduction Contents Warranty Warranty . . . . . . . . . . . . . . . . . . . . .37 User License User License . . . . . . . . . . . . . . . . . .39 Customer Assistance Product Service . . . . . . . . . . . . . . .41 Trademark Acknowledgement . . . .42 Optional Accessories . . . . . . . . . . .43 Accessories Order Info . . . . . . . . . .44 Introduction Important Information . . . . . . . . . .A1 Customer Assistance . . . . . . . . . . .A1 Controls, Indicators and Connections . . . . . . . . . . . . . . . .A2 In This Package . . . . . . . . . . . . . . .A3 Product Overview . . . . . . . . . . . . . . .2 Installation Overview . . . . . . . . . . . .4 Your Detector Installation . . . . . . . . . . . . . . . . . . . .7 Controls and Display . . . . . . . . . . .15 Getting Started . . . . . . . . . . . . . . . .17 EasySet Programming . . . . . . . . . .21 Program Navigation . . . . . . . . . . . .22 Settings . . . . . . . . . . . . . . . . . . . . .24 Detection Alerts . . . . . . . . . . . . . . .29 Radar and Laser . . . . . . . . . . . . . . .32 Maintenance . . . . . . . . . . . . . . . . . .35 Specifications . . . . . . . . . . . . . . . . .36 Nothing Comes Close to a Cobra® 1 Introduction Product Overview · Cobra XRS R7 and XRS R9G WARNING Modifications or parts not approved by Cobra Electronics Corporation may violate FCC Rules and void authority to operate this equipment. Read and understand the information in the Installation Overview and Installation sections of this manual for best operation. The XRS R7 consists of a Main Detector Unit (MDU) and a wireless Remote Display Unit (RDU). The XRS R9G adds a Global Positioning System Locator (GPSL) module, providing fixed red light/speed camera location-based alerts. The XRS R7 can be upgraded with the optional Cobra GPSL to provide fixed red light/speed camera location-based alerts. Main Detector Unit (MDU) The MDU is equipped with an adjustable, two-position bracket for detection operation in the down (horizontal) position or in the up position for a less visible profile from the outside. The MDU issues audible messages during power-on and self-testing. The MDU is also equipped with an alternate power button used to power the unit. The MDU contains detection function sensors so proper mounting and orientation are important. 2 English Introduction Product Overview Remote Display Unit (RDU) The RDU is a wireless remote controller/display module that shows alerts detected by the MDU. The RDU display uses an Extreme Bright DataGrafixTM (Organic Light Emitting Diode) Display to show large graphical alerts as signals are detected. The RDU uses a rechargeable lithium-ion (LiON) battery and is supplied with a holster and clips for mounting on heating/air conditioner vents or sun visor. 12V to 5V USB Power Adaptor with cigarette lighter plug and USB to Mini-USB Retractable Cable are supplied. The RDU can be charged in the vehicle using these two components or by plugging the USB to Mini-USB Retractable Cable to the USB port of your personal computer. The normal Auto Dark screen is almost completely dark with only a moving dot. The Auto Dark screen provides discreet usage and helps conserve RDU battery life. The display color can be changed to match most dash illumination. Global Positioning System Locator (GPSL) (XRS R9G Only) The GPSL module tracks vehicle location. It uses a database that provides alerts as you approach photo-enforced intersections and roads with fixed red light/speed cameras. Use the GPSL functions to program alerts and store up to 1,000 user programmable Location Alerts. Software will be available to update the database and stay current with future photo enforced locations. The GPSL module has no external controls and connects to the MDU with one cable. Registering Your Detector To register your Cobra XRS R7 or XRS R9G go to www.cobra.com. Click on the Product Registration tab. Nothing Comes Close to a Cobra® 3 Introduction Installation Overview Mount Unit Main Detector Unit (MDU) Note: To power the MDU, use one of the two power cords provided (See Page A3). · 12V Power Cord with In-line Fuse for Hardwired Installation: For connection to vehicle's fuse box or battery, or · 12V Power Cord with In-line Fuse and Cigarette Lighter Plug: For connection to 12-volt vehicle accessory outlet (cigarette lighter plug). Fuse box hard wiring is recommended. Use this configuration to provide a more discreet installation. If you are unsure about making this connection yourself, contact a professional installer. Cobra does not warrant any damages to the product or vehicle that may occur as a result of improper installation. On a negative grounded vehicle: Figure A ACC 1. Connect the positive wire [marked with a tag (+)] of the DC power cord to an accessory 12V fuse that is controlled by the ignition switch (Figure A). 2. Connect negative wire (-) to a chassis ground location (Figure A). Body paint may need to be removed to assure a good ground connection. 4 English Introduction Installation Overview Figure C Figure B Mount the MDU high on windshield to right of rear view mirror (Figure B). The MDU must have a clear view through the windshield, be parallel to the road (Figure C) and have clearance to snap into the "up" position. Position the MDU for easy access to power switch, cable connections and for mirror movement. Mount the MDU on the windshield close to the headliner. (See page 7 for details.) Figure D External View THIS SURFACE TOWARDS SKY MDU Lens IMPORTANT: Do not block the MDU lens with the sun-shaded area of the windshield (Figure D). Heated windshields currently available on some vehicles (Instaclear for Ford, Electriclear for GM), may block or weaken incoming signals. Consult your automobile manufacturer. Nothing Comes Close to a Cobra® 5 Introduction Installation Overview Global Positioning System Locator (GPSL) - (XRS R9G Model Only) Figure E Internal View Mount GPSL module close enough to the MDU for supplied cable to connect both modules (Figure E). Mount GPSL with proper side ("This Surface Toward Sky" wording embossed in unit case) attached to windshield and exposed to the sky. Figure F Internal View IMPORTANT: Some States and municipalities prohibit mounting any object on the windshield. If you drive in these states or areas, mount the MDU on the dash (Figure F). IMPORTANT: The MDU will need to be flipped upside-down compared to a windshield installation. Pay special attention to mount the GPSL unit with proper side ("This Surface Toward Sky" wording embossed in unit case) towards the sky. 6 English Your Detector Installation Main Detector Unit (MDU) 1. Position MDU before actual mount. · Do not attempt to adjust MDU bracket. · Hold unit in place. · Using non-permanent pen, mark two opposite corners. 2. Peel off film from two-piece fastener strips. Align with two corner markings made in step 1. Press MDU bracket against windshield. · Fastener strips cannot easily be removed. Strength of adhesive strips increases with time. · Do not pull on MDU for first 20 minutes. Nothing Comes Close to a Cobra® 7 Your Detector Installation 1. Loosen MDU (gray) bracket Not In Use. adjust knob. Stored/Concealed Position. 1 Bracket Adjust Knob 2. Adjust module to a position parallel to the road. Lower to Operating Detection Position. Loosen 2 3 3. Tighten knob to set proper horizontal detection position. The MDU mounting bracket has two detent positions: · one for detection operation (horizontal position) · one for storage or concealment (up position). Makes MDU less visible from outside. Detection Position Tighten IMPORTANT: MDU will not provide any radar/laser detection in "Stored/Concealed" position. 8 English Your Detector Installation 4. Attach power cord to MDU. Use power cord clips to route to fuse box or lighter/accessory outlet, depending on the selected power cord. Surfaces must be clean and free of dirt, oil and dust. Plug in the power cord. Internal View Nothing Comes Close to a Cobra® 9 Your Detector Installation · Remote Display Unit (RDU) Battery Installation 1. Turn RDU over and slide battery cover off of RDU body. 2. Carefully plug battery wire connector into the battery connection port in RDU. Connector only fits one way. 3. Replace battery cover. Battery Charging The unit is shipped with a sealed lithium-ion (LiON) battery pack that is rechargeable. IMPORTANT: Avoid temperature extremes (hot and/or cold) to help prolong battery life and performance. DO NOT leave RDU exposed to direct sunlight. If the RDU is mounted on vent, clip must be on lower fin to avoid hot air blowing on RDU battery compartment. NOTE: When battery begins to discharge too quickly, it is time to install a new battery. 10 English Your Detector Installation 1. Attach 12V to 5V retractable USB power cable to bottom of RDU and to 12V power adapter. 2. Connect 12V power adapter to vehicle accessory outlet (cigarette lighter plug). 3. Initial charge for battery is two (2) hours. (RDU may be used while charging.) WARNING This lithium-ion (LiON) battery should only be recharged inside the RDU. Do not substitute any other type of charging adapter or charging base to charge the battery. Battery damage, fire or explosion may result. NOTE: Lithium-ion (LiON) batteries are toxic. Please dispose of properly. Some municipal waste disposal agencies have special provisions for battery disposal. NOTE: After battery is fully charged, unit can be operated without retractable power cord until battery needs recharging. Nothing Comes Close to a Cobra® 11 Your Detector Installation RDU Holster A holster is provided to allow you to position the RDU for best driver visibility and access while charging the battery. A vent or visor clip will attach to the rear of the holster. Self-adhesive hook and loop strips are also included for alternative mounting locations. Hook and Loop Strips Vent Clip Visor Clip 12 English Your Detector Installation Global Positioning System Locator (GPSL) (XRS Model R9G Only) · 1. Position GPSL before actual mount. · Hold GPSL unit in place with USB cable connected to MDU. · Using non-permanent pen, mark two opposite corners. 2. Peel off film from two-piece fastener strips. Align with two corner markings made in step 1. Press GPSL bracket against windshield. · Fastener strips cannot easily be removed. Strength of adhesive strips increases with time. · Do not pull on GPSL for first 20 minutes. IS CE TH FA DS RR UA SWY K TO S 3. Connect cable between MDU and GPSL. IMPORTANT: Proper side of GPSL module ("This Surface Toward Sky" wording embossed in unit case) must be against windshield and face sky. Nothing Comes Close to a Cobra® 13 Your Detector Installation · GPSL Initial Satellite Lock The GPSL module now needs to detect the Global Positioning satellites. 1. With vehicle running and parked in an area clear of obstructions to the sky, turn on the power to the MDU with GPSL connected. 2. Keep the MDU turned on for at least 15 minutes. This will allow fast satellite acquisition in subsequent power-ups. GPSL Icon IMPORTANT: This procedure may need to be repeated if the unit has not been used for a prolonged period of time. 14 English Your Detector Controls and Display RDU Controls MUTE/ Button Press for Standby Status Screens. Mutes an alert. Selects features in Menu mode. DIM/ Button Press for display brightness. Navigates Menu Screens. Adjusts volume DOWN in Volume mode. CITY/ Button Toggle between Highway and City modes. Navigates Menu Screens. Adjusts volume UP in Volume mode. MENU/SAVE Button Press to enter Menu screen. Press and hold to save User Location (XRS R9G only). POWER/VOLUME Button A two second press and release turns unit on or off. A momentary press for Volume screen. Nothing Comes Close to a Cobra® 15 Your Detector Controls and Display RDU Display Standby Screen The IntelliMute (I-Mute) symbol shows only if the feature is activated. Symbol changes to indicate if above or below Set-point when IntelliMute is turned on. (Refer to page 24.) The RDU link indicators show the the MDU is connected to the RDU by the wireless link. The indicator changes to show a lost connection. RDU battery icon displays charge condition of RDU battery. Sections change to display battery level, or if the battery is being charged. City/Highway symbol changes to indicate activated alert filtering mode. GPS icon indicates GPS satellite lock. Icon changes to indicate lost signal condition.* When arrow is displayed, you can go to the next Standby Control screens by pushing MUTE/ button. Compass indicator uses GPSL to indicate direction of travel.* *Note: The GPS icon, Compass and other GPS features only display if GPSL module is connected (optional for XRS R7, standard on XRS R9G). 16 English Your Detector Getting Started · Power On/Off 1. Press power button on RDU. 2. Unit cycles through power on/self test. Displays Standby screen when process completed. 3. Display changes to Auto Dark operating screen after 30 seconds (factory default). 4. Press, hold power button on RDU for more than two seconds to turn off unit. Nothing Comes Close to a Cobra® 17 Your Detector Getting Started · Standby Screens Press Mute/ while the Standby screen is displayed to cycle through different Standby screens. The Standby screens will be displayed in the following order: Main Standby Screen RDU Battery I-Mute City/Hwy Mode Car Voltage Latitude/ Longitude Speed Compass Compass, Speed and Latitude/Longitude screens only display if GPSL is connected to system. NOTE: Last Standby screen viewed will be displayed when exiting Auto Dark mode. Main Standby Screen Standby screen displays information about detector: alert filtering, automatic muting functions and RDU battery status. If GPSL is connected, compass heading and GPS status icon also display. RDU Battery Charging RDU Battery screen displays status of RDU battery. Indicates charge left in battery or if it is plugged into power source and is charging. I-Mute/City or Hwy Mode I-MUTE CITY I-Mute screen displays status of alert filtering (City or Highway modes) and automatic muting (IntelliMute) functions. Refer to related sections to set these features. Car Voltage Car Voltage screen displays voltage level of car battery. If battery voltage drops below 11.9 volts, an alert sounds. Low Car Voltage feature in Alert Settings programming must be activated. 18 English Your Detector Getting Started Screens display only if GPSL is connected. Compass Compass Indicates driving direction. NW Speed Speed 55 mph Shows speed of vehicle (may be changed to km/h in Menu). Lat / Lon 41º54'53"N 87º47'22"W Lat/Lon Displays latitude and longitude of present location. Nothing Comes Close to a Cobra® 19 Your Detector Getting Started When Auto Dark screen is engaged, a small dot displays at bottom of screen to show that power is on. Touch any button to recall Standby screen. · Auto Dark Highway/City Mode IntelliShield® Tri-level City mode has a Highway mode and three City mode levels: City X, City X Beep Off and City X+K. · IntelliShield® Tri-Level City Mode Toggle from Highway to City mode for three levels of Audio Alert suppression. Pressing City button will toggle between Highway and the default City mode which is City X. Default City mode can be changed within the Menu. Factory setting is City X. City X sounds a single beep when X band signal is first detected but then subsequent audio alert is muted. The alert sounds again when signal strength reaches level 3. City X+K combines City X mode with delay of K band audio alerts until signal strength reaches level 2. City X Beep Off blocks all X band audio alerts until signal strength reaches level 3. Muting Alerts Manual Mute Press MUTE/ button momentarily to turn off Audio Alert during an Alert condition. Press MUTE/ button again during alert to turn on Audio Alert. After current alert is gone, detector will un-mute and next alert sounds. · 20 English Your Detector EasySet Programming · Programming Overview Begin all programming or setup with MENU/SAVE button. Select this to change USER or ALERT settings. USER settings customize how system handles alert filtering, audio-related options, visual options and system-related options. ALERT settings determine which ALERT types are activated. ALERT settings on the XRS R9G model include GPS-related features. Choose Menu Type User Alert Press MENU/SAVE button again to save feature and function changes and return to Standby screen. If a button is not pressed within 15 seconds while in Setup/Programming mode, Standby screen displays and settings made up to this point are saved automatically. NOTE: You can restore factory settings at any time. Enter USER or ALERT settings sub-menu and display shows left arrow , down arrow and right arrow . Arrows correspond with arrows on DIM, MUTE and CITY buttons on RDU. Press left arrow to return to previous screen. Press right arrow to access next screen. Press down arrow to make changes. Press MENU/SAVE button to exit setup program and save new settings. Each of these functions and settings are explained in SETTINGS section of this manual. NOTE: Advancing at the end of menu returns to beginning of menu. NOTE: Setup/Programming mode cannot be accessed during an alert. Unit does not detect signals while in Setup/Programming mode. Nothing Comes Close to a Cobra® 21 Your Detector Program Navigation · Program Flow Diagrams User Settings Diagram Screens display in the following order when cycling through User Settings menu. Speed Units screen displays only if GPSL is connected to system. Pair RDU screen displays only if system detects a missing RDU connection. User Settings City Default Intelli Mute Auto Mute Voice/ Tone RDU Beeps Display Color Pair Remote NOTE: Only shown if RDU lock is lost. Restore Factory Settings Speed Units NOTE: Only shown when GPSL is connected. Smart Power Display Set-up 22 English Your Detector Program Navigation Alert Settings Diagram Screens display in the following order when cycling through Alert Settings menu. Speed Alert, Display GPS Database Version and Delete ALL User Locations screens display only if a GPSL is connected to system. Alert Settings POP X Band K Band Ku Band VG-2 Spectre Delete All User Locations Display GPS Database Speed Alert Low Car Voltage Safety Alert These screens display only if GPSL is connected. Nothing Comes Close to a Cobra® 23 Your Detector Settings · Programming User Settings IntelliMute® Mode Set IntelliMute to mute alerts when vehicle is stopped or moving slowly. Intellimute senses engine RPMs and mutes alerts. IntelliMute does not mute strobe signals from emergency vehicles. IntelliMute works with City and Auto Mute modes. Set an RPM activation point to start IntelliMute. IntelliMute begins muting alerts when engine RPMs fall below set RPMs. The activation point is stored in memory and recalled each time the power is turned on. IntelliMute is factory set off. An IntelliMute icon appears in display when IntelliMute is on and activation is set. When engine RPMs fall below the activation point, Arrow points down. Arrow points up when engine RPMs are above the activation point. If unit stops sensing the engine's RPMs, IntelliMute indicates an error and automatically turns off. When initially choosing your IntelliMute activation point, a setting approximately 300 to 600 RPMs above idle is recommended. Reset the activation point at any time to fit individual preferences and driving style. NOTE: Reset RPM point if detector is used in a different vehicle. IntelliMute may not work with some vehicles because it cannot sense the engine's RPMs. Reduce unwanted audio alerts by using Auto Mute IntelliShield® Tri-level and City Mode. WARNING DO NOT attempt to set the RPM point while driving. Your vehicle should be parked and idling to avoid a collision during the process. 24 English Your Detector Settings Setting IntelliMute From the IntelliMute Setup screen: 1. Press MUTE/ 3. Press DIM/ button to start setup. button to complete setting process. 2. Press and hold the vehicle accelerator at desired engine RPMs. System stores engine RPM setting and displays a completion message and a tone or voice message. Unit must sense a usable pulse within three seconds or a set RPM point within 30 seconds of beginning of setup, or IntelliMute detects an error and turns off. Change a set activation point by accessing Set IntelliMute in User Settings Programming. Repeat three-step setup process above. Auto Mute Mode When Auto Mute is on, it automatically reduces the audio volume of all alerts after they have sounded for four seconds. The signals will remain muted for as long as the signal is detected. When Auto Mute is off, the alerts will sound at full volume for as long as the signal is detected. The factory setting for Auto Mute is On. Press MUTE/ to toggle between Auto Mute vs. Manual Mute. Voice or Tone Mode Set detector to sound alerts and confirm program settings with a Voice or a Tone. Voice Alert provides voice messages in addition to tones. Tone Alert provides tones only. Factory setting is Voice Alert. Remote Display Unit (RDU) Beep Level RDU Beep sets the volume level for the keypad confirmation tones of the RDU. Choose from low, high or off RDU beep level volumes. RDU Display Color The RDU screen color theme is customizable to match your personal preference or your vehicle's dash illumination. Choices include Multi-Color, Red, Blue, Orange or Green. Factory setting is Multi-Color. Nothing Comes Close to a Cobra® 25 Your Detector Settings Display Setup Display Setup determines how long RDU button backlight and display stays on before RDU screen switches to Auto Dark mode. Set RDU display time for 15 seconds, 30 seconds, one minute, three minutes or Always On. Factory default is 30 seconds. NOTE: If selecting "Always On" setting, RDU battery will need charging more frequently. Smart Power Mode SmartPower feature turns system off five minutes after car's engine is turned off. Before SmartPower engages, three beeps sound and SmartPower flashes on display. Start the car or press Power/Pairing button to return to normal power. Factory setting is SmartPower On. Speed Indicator (Shown only if GPSL is connected) Displays vehicle speed in miles per hour (MPH) or kilometers per hour (km/h). Factory setting is MPH. Restore Factory Settings Restore detector to original settings here. Confirmation messages display during process. 26 English Your Detector Settings · Programming Alert Settings POP Alert With Pop Detect mode on, signals are detected and an alert given. During alert unit continues to detect other signals. Factory setting is Pop Detect Off. X Band Alert With X Band Detect mode on, signals are detected and an alert given. During alert unit continues to detect other signals. Factory setting is X Band Detection On. K Band Alert With K Band Detect mode on, signals are detected and an alert given. During alert unit continues to detect other signals. Factory setting is K Band Detect On. Ku Band Alert With Ku Band Detect mode on, signals are detected and an alert given. During alert unit continues to detect other signals. Factory setting is Ku Band Detect Off. VG-2 Alert Detector is undetectable by VG-2 detection devices. An alert is given when such a device is in use near the vehicle. When VG-2 Detect mode is On, VG-2 signals are detected and an alert given. During alert unit continues to detect other signals. Factory setting is VG-2 Detect Off. VG-2 Audio Mode When VG-2 Audio mode is On, alerts are heard and displayed. This setting is only available if VG-2 Alert is On. Factory setting is VG-2 Audio Off. Spectre 1 Alert Detector is undetectable by Spectre 1 detection devices. An alert is given when such a device is in use near the vehicle. When Spectre 1 Detect mode is On, Spectre 1 signals are detected and an alert given. During alert unit continues to detect other signals. Factory setting is Spectre 1 Detect Off. Nothing Comes Close to a Cobra® 27 Your Detector Settings Spectre 1 Audio Mode Spectre 1 Audio mode is only available if Spectre 1 Alert is on. Alerts are audio and displayed on screen. Safety Alert radar signals are detected and alerts given when Safety Alert mode is on. Factory setting is Spectre 1 Audio Off. Safety Alert When Safety Alert mode is On, Safety Alert radar signals are detected and an alert is given. During alert unit continues to detect other signals. Factory setting is Safety Alert On. Low Car Voltage Warning Many U.S. cars have continuous power to 12V outlet and if a device is connected/kept on, it will drain vehicle's battery. To avoid this, XRS R7/R9G comes with SmartPower and Low Car Voltage Warning features. The detector emits a car battery low alert when voltage drops below 11.9 volts. The detector enters SmartPower mode to avoid further battery draining. Factory setting is Car Battery Low On. The following functions are available only if a Global Positioning System Locator is connected to the system. Speed Alert The Speed Alert with the GPSL module tracks vehicle speed and sounds an alert when set speed is exceeded. Speed settings increase or decrease in 5 MPH or km/h increments, depending upon Speed Units chosen in User Settings. Speed Alert must be turned on to see Adjust Speed Setting screen. Factory setting is Off. Display GPS Database Date The GPS database screen is only informational. The screen changes only when you have updated the database. Delete all User Locations Delete all user-programmed location alerts with this screen. 28 English Your Detector Detection Alerts · Detection Alerts Alert Screens All alerts have a unique tone and a vocal alert if the Voice Alert feature is activated. Radar Alerts RADAR RADAR RADAR RADAR X1 Ku1 K1 Ka1 Radar alerts for X band, Ku band, K band and Ka band generate a screen display "RADAR," signal type and a number (1-5) indicating the signal strength. A unique tone sounds with a vocal alert if the Voice Alert feature is activated. RADAR RADAR RADAR POP VG2 SP1 POP, VG2 or SP1 display depending on signal type detected. Laser Alerts ULTRA LYTE PRO LASER PRO LASER 3 20 / 20 L L L L Laser alerts are indicated by an "L" and laser signal type. Nothing Comes Close to a Cobra® 29 Your Detector Detection Alerts Emergency Vehicle Alerts Emergency vehicle alerts are indicated by "EV" and the label "EMERGENCY." EMERGENCY EV ROAD HAZARD Road Hazard Alerts Road Hazard alerts show "RH" and "ROAD HAZARD." RH Railroad Alerts RAILROAD Railroad alerts generate "RR" and "RAILROAD." RR Low Car Voltage Alert WARNING CAR VOLTAGE LOW The detector emits a car battery low alert when voltage drops below 11.9 volts. The detector enters SmartPower mode to avoid further battery draining. Factory setting is Car Battery Low Off. 30 English Your Detector Detection Alerts The following screens are shown only if a Global Positioning System Locator (GPSL) is connected to the system. A detector system with a GPSL also receives alerts based on vehicle location and information in its databases. Photo Enforcement Alerts An alert to a Photo Enforcement area is indicated by a camera surrounded by a circle. As you get closer to the location, the circle and the camera get progressively larger and you hear a unique chime. If the Voice Alert is activated you will also hear a voice alert. In Multi-Color theme the circles change from green, to yellow, to red. User Location Alerts The system can store up to 1,000 User Programmable Location Alerts set to give hazard warnings not known to the GPSL. The screen displays a flag surrounded by a circle. When approaching a stored location, the circle and flag get progressively larger. In addition, a unique tone sounds as vehicle approaches location. A voice alert sounds if Voice Alert is activated. NOTE: A particular User Location can be deleted only when the vehicle returns to that location and receives a User Location Alert. Press MENU/SAVE to delete that location. A confirmation screen displays with "Yes" and "No" selections. Press "Yes" to confirm User Location Deleted. Press "No" to cancel delete. All User Locations can be deleted within the menu (see page 28). Speed Alerts Speed Alert 55 mph Speed alerts are generated when the GPSL senses the vehicle is going faster than the speed setting programmed in the Alert Setting menu. The display indicates actual vehicle speed and a tone sounds. All radar, laser, strobe and safety alerts have priority and override this alert. Factory default is Off. Nothing Comes Close to a Cobra® 31 Your Detector Radar and Laser · Understanding Radar and Laser Radar Speed Monitoring Systems Four band frequencies have been approved by the Federal Communications Commission (FCC) for use by speed monitoring radar equipment: X band K band Ka band Ku band 10.525 GHz 24.150 GHz 33.400 ­ 36.000 GHz 13.435 GHz Your detector detects signals in all four radar bands. VG-2 and Spectre 1 VG-2 and Spectre 1 are "detector detectors" that work by detecting low-level signals emitted by most radar detectors. Your detector does not emit signals that can be detected by VG-2 or Spectre 1, but does detect VG-2 and Spectre 1 signals and alerts you when a device is in use near your vehicle. Safety Alert Traffic Warning System FCC-approved Safety Alert transmitters emit microwave radar signals that indicate the presence of a safety-related concern. Depending on the frequency of the signal emitted, it can indicate a speeding emergency vehicle, train or a stationary road hazard. Because these microwave signals are within the K band frequency, most conventional radar detectors detect Safety Alert signals as standard K band radar. Your detector, however, is designed to differentiate between standard K band and Safety Alert signals, and give separate alerts for each. Safety Alert technology is relatively new. Safety Alert transmitters can be found in limited numbers in all 50 states, but the number is growing. Depending on your location, you may not receive these alerts regularly and may often encounter emergency vehicles, trains and road hazards without being alerted. As the number of transmitters increases, these alerts will become more common. When you receive such an alert, watch for emergency vehicles ahead of you, on cross streets or behind you. If you see an emergency vehicle approaching, pull over to the right side of the road and allow it to pass. 32 English Your Detector Radar and Laser Strobe Alert Special strobes mounted on the light bars of authorized emergency vehicles (fire trucks, police cars, ambulances) automatically change traffic signals as the vehicle approaches an intersection. These strobes and the special strobe detectors located on the traffic signals are already in use in more than 1000 cities nationwide. Cobra's exclusive Strobe Alert detector detects these special strobes and sounds an emergency vehicle alert. When you receive such an alert, watch for an approaching emergency vehicle and pull over to allow it to pass. Contact your local fire and police departments for information about coverage in your area. LIDAR (Laser) The correct name for the technology that most people refer to as "laser" is actually LIDAR, Light Detection And Ranging. LIDAR operates much like radar. Its signal spreads out like a radar signal, though not as widely. Unlike radar, LIDAR must have a clear line of sight to its target vehicle throughout the entire measurement interval. Obstructions such as sign posts, utility poles or tree branches prevent valid speed measurement. Some common questions about LIDAR include: I Does weather have any affect on LIDAR? Yes. Rain, snow, smoke, fog or airborne dust particles reduce the effective range of LIDAR and can, with dense conditions, prevent its operation. I Can LIDAR operate through glass? Yes. Newer LIDAR guns can obtain readings through most types of glass. However, the laser pulse also can be received through glass to trigger an alarm by your detector. Can LIDAR operate while in motion? No. Because LIDAR operates by line of sight, the person using it cannot drive the vehicle, aim and operate the gun all at the same time. Is LIDAR legal to use? Yes. It is legal in all 50 states. I I Nothing Comes Close to a Cobra® 33 Your Detector Radar and Laser Pop Radar Guns The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a single, short-time pulse to measure the target vehicle's speed. The Pop mode receiver senses Pop signals beyond the effective range of Pop radar guns. As the Pop mode receiver is so sensitive, you should limit the use of Pop Detect mode to highway and rural driving. 34 English Your Detector Maintenance · Maintenance Detector is designed and built to give years of trouble-free performance without service. No routine maintenance is required. Follow these steps if unit is not operating properly: I I Make sure power cord is properly connected. Make sure lighter/accessory outlet of vehicle is clean and free of corrosion. Make sure power cord's accessory adapter is firmly seated in lighter/accessory outlet. Check power cord fuse (unscrew ribbed end cap of accessory adapter and examine fuse) or in-line fuse of cable to fuse box, depending on cord used. If required, replace with 2-amp fuse only. NOTE: Rechargeable battery packs should be recycled or disposed of properly in compliance with all applicable laws. Certain states or municipalities provide recycling and have established collection programs. Please contact your local waste removal authority for instructions. WARNING Do Not put battery packs into fire or expose to high heat. They may explode. I I WARNING To reduce risk of damage, use only approved battery packs. Nothing Comes Close to a Cobra® 35 Your Detector Specifications · Band and Frequencies Band X Band K Band Safety Alert Traffic Warning System Frequencies 10.525 24.125 24.070 24.110 24.190 24.230 Ka Band Ku Band Laser Strobe 34.700 13.435 910 700 ± 0.050 ± 0.125 ± 0.010 ± 0.010 ± 0.010 ± 0.010 ± 1.300 ± 0.050 ± 50 ± 300 GHz GHz GHz GHz GHz GHz GHz GHz nm nm This radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432; 5,612,685; 6,078,279; 6,094,148; 6,621,447. Additional patents may be listed inside the product or pending. NOTE: This device complies with part 15 of FCC rules: Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation. 36 English