Operating Instructions 11 BANDTM ULTRA HIGH-PERFORMANCE DIGITAL RADAR/LASER DETECTOR WITH XTREME RANGE SUPERHETERODYNETM TECHNOLOGY XRS 9700 Nothing comes close to a Cobra® Printed in China Part No. 480-107-P English Introduction Important Information And Customer Assistance · Important Information Federal Laws Governing The Use Of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. It is only intended to alert the motorist that an emergency vehicle equipped with a Cobra Safety Alert transmitter is within range as defined by that product. Please call local fire and police departments to learn if coverage exists in your area. Safe Driving Motorists, as well as operators of emergency or service vehicles, are expected to exercise all due caution while using this product, and to obey all applicable traffic laws. Security Of Your Vehicle Before leaving your vehicle, always remember to conceal your radar detector in order to reduce the possibility of break-in and theft. Customer Assistance Customer Assistance Should you encounter any problems with this product, or not understand its many features, please refer to this owner's manual. If you require further assistance after reading this manual, Cobra Electronics offers the following customer assistance services: For Assistance In The U.S.A. Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone). Customer Assistance Operators English and Spanish. 8:00 a.m. to 6:00 p.m. CT Mon. through Fri. (except holidays) 773-889-3087 (phone). Questions English and Spanish. Faxes can be received at 773-622-2269 (fax). Technical Assistance English only. www.cobra.com (on-line: Frequently Asked Questions). English and Spanish. productinfo@cobra.com (e-mail). For Assistance Outside The U.S.A. Contact Your Local Dealer A1 English ©2004 Cobra Electronics Corporation 6500 West Cortland Street Chicago, Illinois 60707 USA www.cobra.com · Introduction Controls, Indicators, Connections And Display · Introduction Product Features · Customer Assistance Order Form · Controls, Indicators, Connections And Display Windshield Bracket Release Button Windshield Bracket Mount Product Features Congratulations! You've made a smart choice by purchasing the XRS 9700 ultra high performance digital radar/laser detector from Cobra. Just look at some of the sophisticated features and capabilities your new unit includes: Xtreme Range Superheterodyne Technology With super-fast sweep circuitry, XRS provides extra detection range and the best possible advance warning to even the fastest radar guns Ultra Performance Provides advanced warning with extra detection range Detection And Separate Alerts For radar signals (X, K and Ka bands, with signal strength indicated), laser signals, Safety Alert signals, Strobe Alert signals, VG-2 signals, Spectre 1 signals 8-Point Compass Displays direction of travel LaserEye For 360° detection of laser and strobe signals Instant-On Ready Detects radar guns with "instant-on" (very fast) speed monitoring capabilities Pop Detection Detects the latest super-fast instant-on signal pulse radar guns Voice Or Tone Alert With adjustable volume DigiView Data Display With easy-to-read alpha/numeric dot matrix text readout IntelliShield False Signal Rejection Reduces falsing in urban areas with Highway mode and three (3) levels of City mode settings Safety Alert Traffic warning system distinguishes important safety alerts from other K band signals Strobe Alert Emergency vehicle warning system Manual Mute Or Auto Mute A mute function of audio alerts IntelliMute A mute function which automatically reduces false alerts by sensing engine RPMs Smart Power A timed power saving function that saves your car's battery EasySet Programming User-friendly mode selection and setting with visual guidance Auxiliary Audio Jack For external speaker connection Mounting Mounts easily on windshield or dashboard Order Form Name Address (No P.O. Boxes) LaserEye For 360° detection of laser and strobe signals. Auxiliary Audio Jack Speaker City State/Province Zip Country Telephone Credit Card Number Type: Ì Visa Ì MasterCard Ì Discover Exp. Date Customer Signature 12V DC Power Jack Item # Description U.S. Cost Each Qty Amount On-Off/Volume Control Allows user to adjust the volume of the tone alerts. Program/Mute Button For manual mute of audio alerts (and to enter programming mode). 420-030-N-001 420-026-N-001 545-139-N-001 CLP-2B Straight 12V Power Cord Coiled 12V Power Cord Windshield Mounting Bracket Dual Port Power Adapter Select/Dim Button Adjusts the display brightness for easy reading (and to scroll through user mode settings while programming). Set/City Button For City or Highway modes to reduce false alerts (and to change user mode settings while programming). U.S. Subtotal Amount Shipping/Handling* Tax Table Wisconsin add 5% $10.00 or less . . . . . $3.00 (Tax if Applicable) Indiana, Michigan, $10.01-$25.00 . . . . . $5.50 Ohio add 6% $25.01-$50.00 . . . . . $7.50 California add 7.25% Shipping/Handling Illinois add 8.75% $50.01-$90.00 . . . . $10.50 Total $90.01-$130.00 . . . $13.50 *For AK, HI and PR add additional $26.95 for FedEx Next Day or $10.95 for FedEx 2nd Day. Excludes weekends and holidays shipments. $130.01-$200.00 . . $16.50 Please allow two (2) to three (3) weeks for delivery in the U.S.A. $200.01 plus . . . . . 10% of purchase Prices subject to change without notice. Ordering From U.S.A. Call 773-889-3087 for pricing or visit www.cobra.com. For Credit Card Orders Complete and return this order form to fax number 773-622-2269. Or call 773-889-3087 [Press one (1) from the main menu] 8:00 a.m. to 6:00 p.m. CT, Monday through Friday. Make Check or Money Order Payable To Cobra Electronics, Attn: Accessories Dept., 6500 West Cortland Street, Chicago, IL 60707 U.S.A. To Order Online Please visit our website: www.cobra.com Nothing comes close to a Cobra® 37 Alpha/Numeric Dot Matrix Text Display* Shows user mode settings, programming instructions, signal strength indication, City/Highway mode indicators, radar, VG-2, Spectre 1 and safety/strobe indicators. System Ready WARNING Modifications or parts substitutions not approved by Cobra Electronics Corporation may violate FCC Rules and void your authority to operate this equipment. * See pages 5 ­ 26 for more information about display features. This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive. A2 English Nothing comes close to a Cobra® A3 Your Detector Installation · Your Detector Installation Installation Where To Mount Your Unit You will get optimum performance from your detector if you Mount it at a point approximately in the center of the vehicle, as low as possible on the front windshield without obstructing the unit's view of the road either to the front or rear. You can also mount it directly on the dashboard. Windshield Mounting Dashboard Mounting Windshield Mounting 1. Attach the rubber cups to the bracket. 2. Make sure the rubber cups and your windshield are clean. 3. Push the bracket firmly onto the windshield. The unit's lens must not be blocked and the LaserEye should have a clear view out the back window to allow 360° detection. The LaserEye Should Have A Clear View 4. Attach the detector to the bracket. Check the angle of the unit. 5. To adjust the angle if necessary, gently push or pull on the bracket to bend it. DO NOT use the detector to bend the bracket. 6. Plug the power cord into the detector. Radar and laser signals pass through glass but not through other materials and objects. Objects that can block or weaken incoming signals include: s s s s Windshield wiper blades Mirrored sun screens Dark tinting at the top of the windshield Heated windshields currently available on some vehicles (Instaclear for Ford, Electriclear for GM). Consult your dealer to see if you have this option. 7. Plug the cigarette lighter adapter on the power cord into your vehicle's cigarette lighter. 8. You can temporarily remove the detector whenever you wish by depressing the bracket release button and sliding it off the bracket. 2 English Nothing comes close to a Cobra® 3 Your Detector Installation Your Detector Getting Started · Dashboard Mounting Getting Started On-Off/ Volume Control Rotate clockwise (away from you) 1. Place the detector on the dashboard to find a location where the unit has a clear, level view of the road. The angle CANNOT be adjusted after mounting. 2. Remove the paper backing from one (1) side of the hook-and-loop fastener. To Turn On The Unit And Adjust The Audio Volume Rotate the On-Off/ Volume control clockwise (away from you). Tone Three (3) beeps Visual Display Testing System Ready Voice Testing, then three (3) beeps 3. Attach the pad to the dashboard at your chosen location and remove the other paper backing. System Ready The display will then Voice Alert cycle through the user mode settings (city or highway, Intellimute and SmartPower status). Start-up is complete when the display continuously shows the current compass direction (N, NE, E, SE, S, SW, W or NW) plus single letters indicating current user mode settings (c = City mode, City X Beep Off mode and City X+K mode, h = Highway mode, i = IntelliMute on). Power On Start-Up Complete 4. Attach the detector to the hook-and-loop fastener. You can remove and reattach the unit as often as you like. 6. Plug the power cord into the detector. Testing 7. Plug the cigarette lighter adapter on the power cord into your vehicle's cigarette lighter. NW h System Ready Voice Alert NOTE In some vehicles, power is supplied to the cigarette lighter even while the ignition is off. If this is the case with your vehicle and you have turned the SmartPower off, you should turn off or unplug your detector when parking for lengthy periods. Cobra recommends leaving SmartPower at the factory setting, which is on. 4 English Se co nd ary Ico ns Nothing comes close to a Cobra® 5 Your Detector EasySet Programming · Your Detector EasySet Programming EasySet Programming All user mode settings on your detector can be changed by using Program mode. When changing the settings, please keep in mind: s s Set/City Button Press and release Select/Dim Button Press and release Program/Mute Button Press and hold/Press and release Buttons can have multiple functions. All settings will be stored in memory when the power is turned off and recalled when the power is turned back on. To Use Program Mode Press and hold the Program/Mute button for two (2) seconds. Tone Three (3) beeps Visual Display Program will appear. PROGRAM The procedure for using Program mode is shown on page 7. NOTE You cannot enter Program mode during an alert. The unit will not detect signals while in Program mode. During programming, if no buttons are pushed for ten (10) seconds, the unit will automatically exit Program mode and save the last settings. Voice Start Program Then brief programming instructions will scroll through the display three (3) times. While the programming instructions are scrolling, press and release the Select/Dim button to cycle through the user modes. With the user mode you wish to change displayed, press and release the Set/City button to change the setting. To move to the next selection, press the Select/Dim button again. When you have finished programming any or all of the user modes, press and release the Program/Mute button to exit Program mode. Or simply wait ten (10) seconds without pushing any buttons. One (1) beep As each mode is displayed, with each the current setting for that button press mode will be shown. None Programming User Modes The tables on pages 8 through 9 show you how to program all user modes and the settings you can choose from. NOTE On the following pages, you will find more detailed explanations of each setting. See page 15 for instructions on setting the IntelliMute activation point. See page 17 for instructions on calibrating the compass. See page 22 for instructions on using SmartPower. One (1) or two (2) beeps, depending on your selection The setting you select will be shown. Current setting One (1) beep When you exit Program Exit Program mode, the new setting will automatically be saved and EXIT PROGRAM and Settings Saved! will appear ...