User manual COMET LABS WRB24

Multi-Function Wireless Router Wireless Access Point Broadband Internet Access 4-Port Switching Hub User's Guide ii Table of Contents CHAPTER 1 INTRODUCTION ........................................................................................... 1 Wireless Router Features ............................................................................................... 1 Package Contents ............................................................................................................ 3 Physical Details................................................................................................................ 4 CHAPTER 2 INSTALLATION............................................................................................. 6 Requirements................................................................................................................... 6 Procedure ......................................................................................................................... 6 CHAPTER 3 SETUP .............................................................................................................. 8 Overview .......................................................................................................................... 8 Configuration Program .................................................................................................. 9 Setup Wizard ................................................................................................................. 11 LAN Screen.................................................................................................................... 14 Wireless Screen.............................................................................................................. 16 Password Screen ............................................................................................................ 19 CHAPTER 4 PC CONFIGURATION ................................................................................ 20 Overview ........................................................................................................................ 20 Windows Clients ............................................................................................................ 20 Macintosh Clients.......................................................................................................... 32 Linux Clients.................................................................................................................. 32 Other Unix Systems....................................................................................................... 32 Wireless Station Configuration.................................................................................... 33 CHAPTER 5 OPERATION AND STATUS ....................................................................... 34 Operation ....................................................................................................................... 34 Status Screen.................................................................................................................. 34 Connection Status - PPPoE .......................................................................................... 36 Connection Status - PPTP ............................................................................................ 38 Connection Status - Telstra Big Pond.......................................................................... 39 Connection Details - SingTel RAS ............................................................................... 40 Connection Details - Fixed/Dynamic IP Address ....................................................... 42 CHAPTER 6 ADVANCED FEATURES ............................................................................ 44 Overview ........................................................................................................................ 44 Advanced Menu Screen ................................................................................................ 44 Advanced Internet Screen ............................................................................................ 45 Access Control ............................................................................................................... 49 Remote Management .................................................................................................... 55 Virtual Servers............................................................................................................... 56 Dynamic DNS (Domain Name Server) ........................................................................ 59 Upgrade Firmware ........................................................................................................ 61 CHAPTER 7 ADVANCED CONFIGURATION............................................................... 62 Overview ........................................................................................................................ 62 PC Database................................................................................................................... 63 Options ........................................................................................................................... 67 Security........................................................................................................................... 69 Logs................................................................................................................................. 71 MAC Address ................................................................................................................ 73 Routing ........................................................................................................................... 74 i APPENDIX A TROUBLESHOOTING .............................................................................. 78 Overview ........................................................................................................................ 78 General Problems .......................................................................................................... 78 Internet Access............................................................................................................... 78 Wireless Access .............................................................................................................. 79 APPENDIX B ABOUT WIRELESS LANS........................................................................ 80 Modes ............................................................................................................................. 80 BSS/ESS.......................................................................................................................... 80 Channels......................................................................................................................... 81 WEP................................................................................................................................ 81 Wireless LAN Configuration........................................................................................ 81 APPENDIX C SPECIFICATIONS ..................................................................................... 82 Multi-Function Wireless Router .................................................................................. 82 Wireless Interface.......................................................................................................... 82 FCC Statement .............................................................................................................. 83 P/N: 9560K30001 Copyright 2003. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. ii Chapter 1 Introduction This Chapter provides an overview of the Wireless Router's features and capabilities. 1 Congratulations on the purchase of your new Wireless Router. The Wireless Router is a multifunction device providing the following services: · · · Shared Broadband Internet Access for all LAN users. 4-Port Switching Hub for 10BaseT or 100BaseT connections. Wireless Access Point for 802.11b Wireless Stations. Figure 1: Wireless Router Wireless Router Features The Wireless Router incorporates many advanced features, carefully designed to provide sophisticated functions while being easy to use. Internet Access Features · Shared Internet Access. All users on the LAN or WLAN can access the Internet through the Wireless Router, using only a single external IP Address. The local (invalid) IP Addresses are hidden from external sources. This process is called NAT (Network Address Translation). DSL & Cable Modem Support. The Wireless Router has a 10BaseT Ethernet port for connecting a DSL or Cable Modem. All popular DSL and Cable Modems are supported. SingTel RAS and Big Pond (Australia) login support is also included. · · PPPoE, PPTP, SingTel RAS and Telstra Big Pond Support. The Internet (WAN port) connection supports PPPoE (PPP over Ethernet), PPTP (Peer-to-Peer Tunneling Protocol), SingTel RAS and Telstra Big Pond (Australia), as well as "Direct Connection" type services. Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the Wireless Router supports both Dynamic IP Address (IP Address is allocated on connection) and Fixed IP Address. 1 · Wireless Router User Guide Advanced Internet Functions · Communication Applications. Support for Internet communication applications, such as interactive Games, Telephony, and Conferencing applications, which are often difficult to use when behind a Firewall, is included. · Special Internet Applications. Applications that use non-standard connections or port numbers are normally blocked by the Firewall. The ability to define and allow such applications is provided, to enable such applications to be used normally. · · Virtual Servers. This feature allows Internet users to access Internet servers on your LAN. The required setup is quick and easy. DMZ. One (1) PC on your local LAN can be configured to allow unrestricted 2-way communication with Servers or individual users on the Internet. This provides the ability to run programs, which are incompatible with Firewalls. URL Filter. Use the URL Filter to block access to undesirable Web sites by LAN users. Internet Access Log. See which Internet connections have been made. VPN Pass through Support. PCs with VPN (Virtual Private Networking) software using PPTP, L2TP and IPSec are transparently supported - no configuration is required. · · · Wireless Features · · · · · Standards Compliant. The Wireless Router complies with the IEEE802.11b (DSSS) specifications for Wireless LANs. Speeds to 22Mbps. All speeds up to the 802.11b maximum of 11Mbps are supported, as well as the TI "B+" enhancement which allows 22Mbps between compatible devices. WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key sizes of 64 Bit, 128 Bit and 256 Bit (for TI devices only) are supported. Access Control. The Access Control feature can ensure that only trusted Wireless Stations can access your LAN. Simple Configuration. If the default settings are unsuitable, they can be changed quickly and easily. LAN Features · · 4-Port Switching Hub. The Wireless Router incorporates a 4-port 10/100BaseT switching hub, making it easy to create or extend your LAN. DHCP Server Support. Dynamic Host Configuration Protocol provides a dynamic IP address to PCs and other devices upon request. The Wireless Router can act as a DHCP Server for devices on your local LAN and WLAN. · Multi Segment LAN Support. LANs containing one or more segments are supported, via the Wireless Router's RIP (Routing Information Protocol) support and built-in static routing table. Configuration & Management · · Easy Setup. Use your WEB browser from anywhere on the LAN or WLAN for configuration. Remote Management. The Wireless Router can be managed from any PC on your LAN. And, if the Internet connection exists, it can also (optionally) be configured via the Internet. 2 Introduction · UPnP Support. UPnP (Universal Plug and Play) allows automatic discovery and configuration of the Wireless Router. UPnP is by supported by Windows ME, XP, or later. Security Features · · · Password - protected Configuration. Optional password protection is provided to prevent unauthorized users from modifying the configuration data and settings. Wireless LAN Security. WEP (Wired Equivalent Privacy) is supported, as well as Wireless access control to prevent unknown wireless stations from accessing your LAN. NAT Protection. An intrinsic side effect of NAT (Network Address Translation) technology is that by allowing all LAN users to share a single IP address, the location and even the existence of each PC is hidden. From the external viewpoint, there is no network, only a single device - the Wireless Router. · Stateful Inspection Firewall. All incoming data packets are monitored and all incoming server requests are filtered, thus protecting your network from malicious attacks from external sources. Protection against DoS attacks. DoS (Denial of Service) attacks can flood your Internet connection with invalid packets and connection requests; using so much bandwidth and so many resources that Internet access becomes unavailable. The Wireless Router incorporates protection against DoS attacks. · Package Contents The following items should be included: · · · · The Wireless Router Unit Power Adapter Quick Installation Guide CD-ROM containing the on-line manual. If any of the above items are damaged or missing, please contact your dealer immediately. 3 Wireless Router User Guide Physical Details Front Panel Figure 2: Front Panel Status (Red) LED On - Error condition. Off - Normal operation. Blinking - This LED blinks during start up. Power LED On - Power on. Off - No power. LAN LEDs For each port, there are 2 LEDs · Link/Act · · · · 100 · · WAN LED On - Corresponding LAN (hub) port is using 100BaseT. Off - Corresponding LAN (hub) port connection is using 10BaseT, or no active connection. On - Corresponding LAN (hub) port is active. Off - No active connection on the corresponding LAN (hub) port. Flashing - Data is being transmitted or received via the corresponding LAN (hub) port. On - Connection to the Broadband Modem attached to the WAN (Internet) port is established. Off - No connection to the Broadband Modem. On - Idle. Off - Error - No Wireless connection available. Flashing - Data is being transmitted or received via the Wireless access point. This includes "network traffic" as well as user data. WLAN LED 4 Introduction Rear Panel Figure 3: Rear Panel Reset Button This button has two (2) functions: · · Reboot. When pressed and released, the Wireless Router will reboot (restart). Clear All Data. This button can also be used to clear ALL data and restore ALL settings to the factory default values. To Clear All Data and restore the factory default values: 1. Power Off. 2. Hold the Reset Button down while you Power On. 3. Keep holding the Reset Button for a few seconds, until the RED LED has flashed TWICE. 4. WAN port (10/100BaseT) 10/100BaseT LAN connections Power port Release the Reset Button. The Wireless Router is now using the factory default values. Connect the DSL or Cable Modem here. If your modem came with a cable, use the supplied cable. Otherwise, use a standard LAN cable. Use standard LAN cables (RJ45 connectors) to connect your PCs to these ports. Connect the supplied power adapter here. 5 Chapter 2 Installation This Chapter covers the physical installation of the Wireless Router. Requirements · · · · Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors. TCP/IP protocol must be installed on all PCs. For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem (for WAN port usage) To use the Wireless Access Point, all Wireless devices must be compliant with the IEEE802.11b specifications. Procedure Figure 4: Installation Diagram 1. Choose an Installation Site Select a suitable place on the network to install the Wireless Router. Ensure the Wireless Router and the DSL/Cable modem are powered OFF. For best Wireless reception and performance, the Access Point should be positioned in a central location with minimum obstructions between the Access Point and the PCs. Also, if using multiple Access Points, adjacent Access 6 Installation Points should use different Channels. 2. Connect LAN Cables Use standard LAN cables to connect PCs to the Switching Hub ports on the Wireless Router. Both 10BaseT and 100BaseT connections can be used simultaneously. 3. Connect WAN Cable Connect the DSL or Cable modem to the WAN port on the Wireless Router. Use the cable supplied with your DSL/Cable modem. If no cable was supplied, use a standard cable. 4. Power Up · · Power on the Cable or DSL modem. Connect the supplied power adapter to the Wireless Router and power up. Use only the power adapter provided. Using a different one may cause hardware damage 5. Check the LEDs · · · · · The Power LED should be ON. The Status LED should flash, then turn OFF. If it stays on, there is a hardware error. For each LAN (PC) connection, the LAN Link/Act LED should be ON (provided the PC is also ON.) The WAN LED should be ON. The WLAN LED should be ON For more information, refer to the Front Panel section in Chapter 1. 7 Chapter 3 Setup This Chapter provides Setup details of the Wireless Router. 3 Overview This chapter describes the setup procedure for: · · · · Internet Access LAN configuration Wireless setup Assigning a Password to protect the configuration data. PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC Configuration. Other configuration may also be required, depending on which features and functions of the Wireless Router you wish to use. Use the table below to locate detailed instructions for the required functions. To Do this: Configure PCs on your LAN. Check Wireless Router operation and Status. Use any of the following Internet features: · · · · · · Special Applications DMZ Virtual Servers Dynamic DNS Remote Management Firmware Upgrade Chapter 7 Advanced Configuration Refer to: Chapter 4: PC Configuration Chapter 5: Operation and Status Chapter 6: Advanced Features Use any of the following Advanced Configuration settings: · · · PC Database Options (Backup DNS, TFTP, UPnP, Firewall) Routing (RIP and static Routing) Where use of a certain feature requires that PCs or other LAN devices be configured, this is also explained in the relevant chapter. 8 Setup Configuration Program The Wireless Router contains an HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Your Browser must support JavaScript. The configuration program has been tested on the following browsers: · · Netscape V4.08 or later Internet Explorer V4 or later Preparation Before attempting to configure the Wireless Router, please ensure that: · Your PC can establish a physical connection to the Wireless Router. The PC and the Wireless Router must be directly connected (using the Hub ports on the Wireless Router) or on the same LAN segment. The Wireless Router must be installed and powered ON. If the Wireless Router's default IP Address (192.168.0.1) is already used by another device, the other device must be turned OFF until the Wireless Router is allocated a new IP Address during configuration. · · Using UPnP If your Windows system supports UPnP, an icon for the Wireless Router will appear in the system tray, notifying you that a new network device has been found, and offering to create a new desktop shortcut to the newly-discovered device. · · · Unless you intend to change the IP Address of the Wireless Router, you can accept the desktop shortcut. Whether you accept the desktop shortcut or not, you can always find UPnP devices in My Network Places (previously called Network Neighborhood). Double - click the icon for the Wireless Router (either on the Desktop, or in My Network Places) to start the configuration. Refer to the following section Setup Wizard for details of the initial configuration process. Using your Web Browser To establish a connection from your PC to the Wireless Router: 1. After installing the Wireless Router in your LAN, start your PC. If your PC is already running, restart it. 2. Start your WEB browser. 3. In the Address box, enter "HTTP://" and the IP Address of the Wireless Router, as in this example, which uses the Wireless Router's default IP Address: HTTP://192.168.0.1 9 Wireless Router User Guide If you can't connect If the Wireless Router does not respond, check the following: · The Wireless Router is properly installed, LAN connection is OK, and it is powered ON. You can test the connection by using the "Ping" command: · · Open the MS-DOS window or command prompt window. Enter the command: ping 192.168.0.1 If no response is received, either the connection is not working, or your PC's IP address is not compatible with the Wireless Router's IP Address. (See next item.) · If your PC is using a fixed IP Address, its IP Address must be within the range 192.168.0.2 to 192.168.0.254 to be compatible with the Wireless Router's default IP Address of 192.168.0.1. Also, the Network Mask must be set to 255.255.255.0. See Chapter 4 - PC Configuration for details on checking your PC's TCP/IP settings. Ensure that your PC and the Wireless Router are on the same network segment. (If you don't have a router, this must be the case.) · 10 Setup Setup Wizard The first time you connect to the Wireless Router, the Setup Wizard will run automatically. (The Setup Wizard will also run if the Wireless Router's default settings are restored.) 1. Step through the Wizard until finished. · You need to know the type of Internet connection service used by your ISP. Check the data supplied by your ISP. 2. 3. · The common connection types are explained in the tables below. On the final screen of the Wizard, run the test and check that an Internet connection can be established. If the connection test fails: · · · Check your data, the Cable/DSL modem, and all connections. Check that you have entered all data correctly. If using a Cable modem, your ISP may have recorded the MAC (physical) address of your PC. Run the Wizard, and on the Cable Modem screen, use the "Clone MAC address" button to copy the MAC address from your PC to the Wireless Router. Common Connection Types Cable Modems Type Dynamic IP Address Details Your IP Address is allocated automatically, when you connect to you ISP. ISP Data required Usually, none. However, some ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address. IP Address allocated to you. Some ISP's may also require you to use a particular Hostname, Domain name, or MAC (physical) address. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. DSL Modems Type Dynamic IP Address Static (Fixed) IP Address PPPoE Details Your IP Address is allocated automatically, when you connect to you ISP. Your ISP allocates a permanent IP Address to you. You connect to the ISP only when required. The IP address is usually allocated automatically. ISP Data required None. IP Address allocated to you. User name and password. 11 Wireless Router User Guide PPTP Mainly used in Europe. You connect to the ISP only when required. The IP address is usually allocated automatically, but may be Static (Fixed). · · · PPTP Server IP Address. User name and password. IP Address allocated to you, if Static (Fixed). Other Modems (e.g. Broadband Wireless) Type Dynamic IP Address Static (Fixed) IP Address Details Your IP Address is allocated automatically, when you connect to you ISP. Your ISP allocates a permanent IP Address to you. ISP Data required None. IP Address allocated to you. Big Pond Cable (Australia) For this connection method, the following data is required: · · · User Name Password Big Pond Server IP address SingTel RAS For this connection method, the following data is required: · · · User Name Password RAS Plan 12 Setup Home Screen After finishing the Setup Wizard, you will see the Home screen. When you connect in future, you will see this screen when you connect. An example screen is shown below. Figure 5: Home Screen Navigation & Data Input · · Use the menu bar on the top of the screen, and the "Back" button on your Browser, for navigation. Changing to another screen without clicking "Save" does NOT save any changes you may have made. You must "Save" before changing screens or your data will be ignored. On each screen, clicking the "Help" button will display help for that screen. From any help screen, you can access the list of all help files (help index). 13 Wireless Router User Guide LAN Screen Use the LAN link on the main menu to reach the LAN screen. The example screen is shown below. Figure 6: LAN Screen Data - LAN Screen TCP/IP IP Address IP address for the Wireless Router, as seen from the local LAN. Use the default value unless the address is already in use or your LAN is using a different IP address range. In the latter case, enter an unused IP Address from within the range used by your LAN. The default value 255.255.255.0 is standard for small (class "C") networks. For other networks, use the Subnet Mask for the LAN segment to which the Wireless Router is attached (the same value as the PCs on that LAN segment). · If enabled, the Wireless Router will allocate IP Addresses to PCs (DHCP clients) on your LAN when they start up. The default (and recommended) value is enabled. If you are already using a DHCP Server, this setting must be disabled, and the existing DHCP server must be re-configured to treat the Wireless Router as the default Gateway. See the following section for further details. Subnet Mask DHCP Server · · The Start IP Address and Finish IP Address fields set the values used by the DHCP server when allocating IP Addresses to DHCP clients. This range also determines the number of DHCP clients supported. See the following section for further details on using DHCP. Buttons Save Cancel Save the data on screen. The "Cancel" button will discard any data you have entered and reload the file from the Wireless Router. 14 Setup DHCP What DHCP Does A DHCP (Dynamic Host Configuration Protocol) Server allocates a valid IP address to a DHCP Client (PC or device) upon request. · · · · The client request is made when the client device starts up (boots). The DHCP Server provides the Gateway and DNS addresses to the client, as well as allocating an IP Address. The Wireless Router can act as a DHCP server. Windows 95/98/ME and other non-Server versions of Windows will act as a DHCP client. This is the default Windows setting for the TCP/IP network protocol. However, Windows uses the term Obtain an IP Address automatically instead of "DHCP Client". You must NOT have two (2) or more DHCP Servers on the same LAN segment. (If your LAN does not have other Routers, this means there must only be one (1) DHCP Server on your LAN.) · Using the Wireless Router's DHCP Server This is the default setting. The DHCP Server settings are on the LAN screen. On this screen, you can: · · Enable or Disable the Wireless Router's DHCP Server function. Set the range of IP Addresses allocated to PCs by the DHCP Server function. You can assign Fixed IP Addresses to some devices while using DHCP, provided that the Fixed IP Addresses are NOT within the range used by the DHCP Server. Using another DHCP Server You can only use one (1) DHCP Server per LAN segment. If you wish to use another DHCP Server, rather than the Wireless Router's, the following procedure is required. 1. Disable the DHCP Server feature in the Wireless Router. This setting is on the LAN screen. 2. Configure the DHCP Server to provide the Wireless Router's IP Address as the Default Gateway. To Configure your PCs to use DHCP This is the default setting for TCP/IP under Windows 95/98/ME. See Chapter 4 - Client Configuration for the procedure to check these settings. 15 Wireless Router User Guide Wireless Screen The Wireless Access Point settings must match the other Wireless stations. To change the Wireless Router's default settings for the Wireless Access Point feature, use the Wireless link on the main menu to reach the Wireless screen. An example screen is shown below. Figure 7: Wireless Screen Data - Wireless Screen Identification Regulatory Domain Station name It is illegal to use this device in any location outside of the regulatory domain. This is the same as the "Device Name" for the Wireless Router. On your PC, some Wireless status screens may display this name as the name of the Access Point in use. SSID (ESSID) · If using an ESS (Extended Service Set, with multiple access points) this ID is called an ESSID (Extended Service Set Identifier). To communicate, all Wireless stations should use the same SSID/ESSID. Select the Channel you wish to use on your Wireless LAN. If you experience interference (shown by lost connections and/or slow data transfers) you may need to experiment with different channels to see which is the best. If using multiple Access Points, adjacent Access Points should use different Channels to reduce interference. · Options Channel No. · · · 16