Under Cabinet CD Clock Radio with Remote MODEL SCR2608 INSERUCTION MANUAL Operating Instructions BEFORE OPERATION THIS PRODUCT, READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS. Be sure to save this booklet for future reference. IMPORTANT SAFETY INSTRUCTIONS The Lightning flash with arrowhead symbol, with an equilateral triangle is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THESE IMPORTANT SAFETY INSTRUCTIONS ARE INCLUDED, AS APPLICABLE TO THE APPLIANCE, CONVEYING TO THE USER THE FOLLOWING INFORMATION: Heed Warnings- All warnings on the appliance and in the operating instructions should be adhered to. Follow instructions- All operating and use instructions should be followed. Water and moisture- The appliance should not be used near water. For example, near a bathtub, washbowl, kitchen sink, or near a swimming pool, and the like Ventilation- The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase that impedes the flow of air through the ventilation openings. Heat ­ The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that product heat. Power Sources-The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarization ­ Precautions should be taken so that the grounding or polarization means of the appliance are not defeated. Power-Cord Protection- Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. Cleaning-The appliance should be cleaned only as recommended by the manufacturer. Nonuse Periods-The power cords of the appliance should be unplugged from the outlet when unused for an extended period of time Object and Liquid entry-Care should be taken so that objects do not fall and liquids are not spilled into the housing. Damage Requiring Service-The appliance should be serviced by qualified service personnel when: · The Power-supply cord or the plug has been damaged; or · Object have fallen or liquid has been spilled into the appliance; or · The appliance has been exposed to rain ; or · The appliance does not appear to operate normally or exhibits a marked changed in performance ;or · The appliance has been dropped or the housing damaged. Servicing-The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. Do not take the unit apart. The laser beam used in the unit could harm your eyes. Do not insert pins or other objects inside the unit . This unit is equipped with a safety device which automatically turns the laser beam off when the disc compartment is opened. If a pin or other metal objects get inside the unit, this safety device may be deactivated. Do not drop the unit or subject it to strong shocks. Doing so could result in damage. Do not place the unit in the following: Locations where the temperature is high . The unit's housing may warp or the unit may otherwise be damaged if it is placed in direct sunlight, near heaters (where the temperature is 1400F/600C or greater) or in cars with the windows closed. · In humid or dusty locations · In locations exposed to heavy vibrations · On unstable or tilted surfaces. CAUTION: * This product is equipped with a polarized plug (one blade is wider than the other blade) as a safety feature to reduce the risk of electrical shock. This plug will fit into a polarized outlet only one way. This is a safety feature. If you are unable to insert the plug into the electrical outlet, try reversing the plug. If the plug still does not fit, contact a qualified electrician. Never use the plug with an extension cord unless the plug can be fully inserted into the extension cord. Do not alter the plug. Do not attempt to defeat the safety purpose of the polarized plug, * Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SAFETY CERTIFICATION This Compact Disc Player is made and tested to meet the safety standards of the Federal Communications Commission(FCC) and to comply with the safety performance requirements of the U.S. Department of Health and Human Services and with the Food & Drug Administration(FDA) Radiation performance Standards 21 CFR Subchapter J. IMPORTANT INFORMATION REQUIRED BY THE FCC Since the Compact Disc (CD) circuitry may cause interference to other radios nearby, switch this set off when not in use or move it away from the affected radios. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received , including interference that may cause undesirable operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio elevation reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures; *Reorient or relocate the receiving antenna. *Increase the separation between the equipment and receiver. *Connect the equipment into an outlet on a circuit different from that to which receiver is connected. *Consult the dealer or an experienced radio/TV technician for help LASER SAFETY THIS SET EMPLOYS AN OPTICAL LASER BEAM SYSTEM IN THE CD MECHANISM DESIGNED WITH BUILT-IN SAFEGUARDS. DO NOT ATTEMPT TO DISASSEMBLE. EXPOSURE TO THIS INVISIBLE LASER LIGHT BEAM MAY BE HARMFUL TO THE EYES. THIS COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. THE LASER MECHANISM IN THE SET CORRESPONDS TO THE STYLUS (NEEDLE) OF A RECORD PLAYER. ALTHOUGH THIS PRODUCT USES A LASER PICK-UP LENS, IT IS COMPLETELY SAFE WHEN OPERATED ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS CONTAINED HEREIN. LOCATION OF CONTROLS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. LCD DISPLAY- A (for CD, CLOCK AND RADIO) VOLUME DOWN VOLUME UP CD DRAWER REMOTE SENSOR POWER ON INDICATOR POWER/ ALARM OFF BUTTON CD DRAWER OPEN/CLOSE BUTTON LCD DISPLAY B (FOR TIMER) MINTUE SET BUTTON (FOR TIMER) HOUR SET BUTTON (FOR TIMER) STEREO/MONO BUTTON (FOR FM RADIO ONLY) 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. FAST FORWARD (SKIP >>|) BUTTON REWIND (SKIP |<<) BUTTON STOP/ RADIO BAND BUTTON PLAY/PAUSE BUTTON RADIO BUTTON CD BUTTON DISPLAY/ALARM SET BUTTON MEMORY/CLOCK ADJUST BUTTON REPEAT/MEMORY. RECALL BUTTON BATTERY DOOR(FOR CLOCK BACK UP) AC POWER CORD POWER WIRE HOLDER FM ANTENNA REMOTE CONTROL 1. 2. 3. 4. 5. 6. 7. 8. 9. OPEN /CLOSE KEY PLAY/PAUSE KEY FAST FORWARD (SKIP >>|) BUTTON VOLUME UP KEY VOLUME DOWN KEY REWIND (SKIP |<<) BUTTON RANDOM KEY MUTE KEY CD/ RADIO MEMORY KEY (MEM) 10. 11. 12. 13. 14. 15. 16. 17. 18. SNOOZE KEY ALARM SET KEY SLEEP KEY EQUALIZATION PRESET KEY (EQ) REPEAT KEY FUNCTION KEY ( to select the CD, Radio function) STOP/RADIO BAND KEY POWER/ ALARM OFF KEY Battery compartment (for Remote control) Insert two(2) "AAA" /1.5V(not included) batteries following the polarity as indicated in the compartment to the right. Alkaline batteries are recommended for long using time. Note: when planning not to use the remote control for a long time. Remove the batteries in order to avoid the electrolyte leakage. Under Cabinet Mounting Instructions Tools Required Drill and 1/4" Drill Bit Ruler or Tape Measure Nail or Awl Scissors Screwdriver ­ Phillips Countersink (Optional) Masking Tape Safety Glasses 1 ­ Mounting template Parts Packed with your unit 1. 2. 3. 4. Spacers (3pcs of 1/4" , 3pcs of 1/2", 3pcs of 1") Washers (3pcs) Phillips head screws (3pcs of 2 3/4", 3pcs of 1 5/8") Mounting Template Before Mounting Empty contest of the selected cabinet under which the unit will be mounted and thoroughly clean the underside of the cabinet to remove any grease residue which might be present. We recommend the unit be mounted at the front edge of the cabinet. Important: For secure mounting, the screws must go into the radio to a depth of at least 3/8". If the overall length from the bottom of the cabinet shelf to the bottom of the over hand is more the 1 3/4". Then a wood shim will be necessary. A shim can be made from a sheet of plywood, using the Template to located the central lines for drilling the 1/4" mounting holes; the shim can be located between the cabinet shelf bottom and spacers. Make sure the wood is at least as thick as the excess over 1 3/4" if a shim is necessary, longer screws are required. Longer screws (Type#10-32) are available at most local hardware stores Cut out the template on the line indicated. The template size and the screw hold positions are identical to the top of the Clock radio. Mounting Procedure Step 1. If your cabinet does not have a overhang: a) Position template in desired location on underside of cabinet, flush with front edge. b) Then tape template in pace and go to step 2. If your cabinet have overhang: a) Measure the thickness of the overhang. b) Fold front of the template downward along the printed guideline that is closet to the thickness of your cabinet. c) Tape fold-down portion to backside of overhand, tape template to cabinet underside. Note: If your cabinet has glue blocks or other obstructions, cut out corresponding areas on the template to clear them. Do not cut or cut through the screw holes indicated on the template. CAUTION: It is recommended that safety glasses be worn while drilling screw holes to prevent the possibility of eye injury. Step 2 Drill 1/4" inches diameter holes through the underside of the cabinet bottom shelf using the three points marked on the template. Helpful Hints: On wooden cabinets you may want to mark and start the drill holes with a nail or an awl. Be sure to hold the drill very firmly against the cabinet to reduce "walking" of the drill bit from the markings. Using masking tape above the hole locations on inside of wooden cabinet shelf to help reduce splintering. If installing the unit under a wood cabinet, you may wish to countersink the drilled hold for the INSIDE of the cabinet if a countersink the holes use the supplied washers. Step 3 Remove template and clean drill shavings from inside and underside of cabinet. Step 4 If your cabinet does not have an overhang. Go to Step 5. If your cabinet has an overhang. Select the spacer or combination of spacers that is equal to or longer than the cabinet overhang. Step 5. Insert screws from inside the cabinet. The washers must be used on metal cabinets, and on wood cabinets if you did not countersink the drilled holes. Position washers, flat side down, and place screws into the holes. If your cabinet does not have an overhang, go to Step 7. Step 6. Hold screw heads down while you push the selected spacers onto the screws under the cabinet. Be sure to push up spacers until they fully nested (if more then one is in used) Step 7 Align radio under the screws. Hold the screw holes in the top of the clock radio against the mounting screws and partially tighten the screws. Do not fully tighten until all 3 screws have been started. (The top front edge of the clock radio should clear the overhang.) Power Wire Holder It is for rounding the extra power wire after user had plugged the power cord to the electrical outlet. FULL LCD DISPLAY UNIT POWER SUPPLY ( Mains 120V/60Hz) Connect the power cable plug to the (120V) wall outlet. Warning: Before using the unit. Check that the local mains supply is compatibl ...