DTB-21U7 S DTB-21U7 NS ADDITIONAL INFORMATION FOR TV'S SOLD IN GREAT BRITAIN The appliance is supplied with a moulded three pin mains plug fitted with 5Amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 5 amp and approved by ASTA or BSI to BS1362. The plug contains a removable fuse cover that must be refitted when the fuse is replaced.In the event of the fuse cover being lost or damaged, the plug must not be used until a replacement cover has been obtained.Replacement fuse covers can be purchased from your nearest electrical dealer and must be the same colour as the original. If the moulded mains plug is unsuitable for the socket outlet in your home or is removed for any other reasons, then the fuse should be removed and the cut off plug disposed of safely to prevent the hazard of electric shock. There is a danger of electric shock if the cut off plug is inserted into any socket outlet. If a replacement plug is to be fitted, please observe the wiring code shown below.The wires in the mains lead are are coloured in the accordance with the following code: Blue-neutral Brown-live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not make any connections to the terminal in the plug which is marked by the letter E by the safety earth symbol or coloured green or green and yellow. 1 CONTENT REMOTE CONTROL & TV CONNECTIONS...............................................3 IMPORTANT SAFEGUARDS.......................................................................4 INSTALLATION............................................................................................4 START UP....................................................................................................5 CONNECTING EXTERNAL EQUIPMENT...................................................5 DAILY USE...................................................................................................6 MENUS DESCRIPTION...............................................................................8 TELETEXT..................................................................................................11 2 REMOTE CONTROL & TV CONNECTIONS LOCAL CONTROL Front VIDEO L-AUDIO-R ON/OFF B1 B2 B3 B4 B5 B6 B7 B8 PR B9 B1 B2 B3 B4 B5 MAIN POWER button FRONT VIDEO INPUT socket FRONT AUDIO INPUT (L + R) socket HEADPHONE socket STAND-BY indicator B6 B7 B8 B9 REMOTE sensor TV / AV button VOLUME UP/DOWN buttons PROGRAM UP/DOWN buttons Rear ANT C3 C1 C2 AV1 AV2 C1 C2 C3 SCART 1 socket SCART 2 socket AERIAL jack ANT AV1 AV2 REMOTE CONTROL UNIT TV mode A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 POWER SOUND MUTE NUMBER 0..9 SLEEP TV / AV PROGRAM UP (CURSOR UP) VOLUME DOWN (CURSOR LEFT) . . . SKIP MOVE 3D(SOUND EFFECT) MODE ZOOM RECALL NORMAL OK MENU VOLUME UP (CURSOR RIGHT) PROGRAM DOWN (CURSOR DOWN) TV > TELETEXT . . . DELETE A2 A1 A13 A3 A14 A15 A17 A4 A6 A5 A7 A16 A18 A19 A20 A21 A8 A9 A10 A11 A12 A22 A23 A24 A25 A26 TELETEXT mode A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 POWER SOUND MUTE NUMBER 0..9 . . PAGE UP VOLUME DOWN BRIGHT. DOWN CANCEL PAGE HOLD SUBPAGE RED GREEN . . . . . INDEX MENU VOL./ BRIGHT. SELECTION VOLUME UP BRIGHT. UP PAGE DOWN TELETEXT > TV HEIGHT REVEAL CYAN YELLOW 3 IMPO RT A N T SA FEG U A RD S WATER AND MOISTURE Never install the set in the following places: In a wet basement, bathroom. Do not place any container with liquid on the set. HEAT Never place the set near heat sources. VENTILATION Do not cover the ventilations openings in the cabinet and never place the set in a confined space such as in a bookcase or built-in cabinet unless proper ventilation is provided. Leave a minimum 10 cm gap all around the unit. OBJECT ENTRY Do not insert foreign objects, such as needles and coins, in the ventilation openings. LIGHTNING STRIKING You should disconnect the set from the mains and the aerial system during thunderstorms. CLEANING Unplug the set from the mains during cleaning. AFTER MOVING THE SET If the set is moved or turned, the MAIN POWER button must be switched off for at least 15 minutes in order to take out colour patches on the screen. IN ST A LLAT IO N Batteries ANT AV1 AV2 Open remote control battery compartment (at the rear) and insert two 1.5V type AAA batteries. Warning: be careful to respect battery polarities. Insert the main plug into a 230V 50Hz AC power socket. Connect aerial to aerial jack (C3). SWITCHING ON AND OFF VIDEO L-AUDIO-R ON/OFF Power on the TV set using front panel MAIN POWER button (B1). Select your preferred language from the LANGUAGE menu (see section START UP on page 5). Press the remote control MENU button (A19) to enter the main menu. Select Install menu to tune and memorise TV programs. 4 ST A RT U P LANGUAGE MENU The very first time that you turn on the TV, the LANGUAGE menu will appear on the screen. It's purpose is to select the language that will be used for all the OSD (On Screen Display) menus. The user must enter a choice of language before proceeding further. The language entered at this stage can still be modified at any later time, by entering the FEATURES menu (see later section under MENU DESCRIPTION). The descriptions used in the menu are those of the country code (e.g. GB = English, RUS = Russian etc). LANGUAGE PR CZ FIN N S D GB NL SLO DK GR PL E H RO F I RUS MENU Selection is made by use of the remote control CURSOR UP (A6)) / CURSOR DOWN (A21) keys and CURSOR RIGHT (A20) / LEFT (A7) keys. Once you are satisfied with your selection, push the OK button (A18) to confirm your choice, after which the menu will disappear. The menu will never appear again. PR C O N N EC T IN G EX T ERN A L EQ U IPMEN T The rear Scart 1 (C1), Scart 2 (C2) sockets and the front AV socket (B2) (B3) are three dedicated sockets to connect audio-video equipment. Rear ANT AV1 AV2 ANT AV1 AV2 REAR SCART 1 SOCKET (AV1) This socket (C1) has video / audio inputs and outputs It is recommended to connect to this socket automatic AV switching equipment such as pay-TV decoders, video games, DVD players and most VCR's. In most cases, when connecting powered equipment to this socket, the TV set switches automatically to AV mode. If not, then use the TV/AV buttons (A5) or(B7) to select AV1. VCR / DVD / Video Game / Pay-TV decoder REAR SCART 2 SOCKET (AV2) This socket (C2) has video / audio inputs and outputs(Note : DTB-21U7 NS has no sound outputs and sound input is common with front socket AV3). Automatic AV switching equipment (for example most VCR's) can be connected to this socket. In most cases, when connecting powered equipment to this socket, the TV set switches automatically to AV mode. If not, then use the TV/AV buttons (A5) or (B7) to select AV2. You can also receive an S-VHS signal with REAR SCART2 socket, by selecting SVHS2 with the TV / AV buttons (A5) or (B7). Important: If your video equipment does not have SCART socket(s), or if you wish to use only the aerial (RF) connection (not recommended), then you should make use of PR 00 on the TV set for best performance. HEADPHONE SOCKET To hear TV sound with headphones, insert a 3.5mm headphone plug into the headphone socket (B4). The speaker's sound will be automatically cut off. Front FRONT AV SOCKET (AV3) The front AV socket (B2) (B3) has audio and video inputs. To switch from TV to these inputs, use the TV / AV buttons (A5) or (B7) and select AV3. OR CAMCORDER VIDEO GAME Note : DTB-21U7 NS, sound input is common with rear SCART2 socket (AV2). TV/AV SELECTION Allows to switch between TV and external modes. By repeatedly pressing the remote control TV / AV (A5) or the TV front panel TV / AV (B7) button, the onscreen display is changed as shown AV1 > AV2 > SVHS2 > AV3 > TV 5 DAILY USE SWITCHING ON TV SET 1) If stand-by indicator (B5) is red, then the TV set is in stand-by mode. You can switch on using the remote control POWER button (A1), the NUMBER 0....9 buttons (A3), or PROGRAM UP (A6) / DOWN (A21) buttons. The front panel PROGRAM UP/DOWN buttons (B9) can also be used. Once on, the stand-by indicator turns to green and the picture appears on the screen. 2) If stand-by indicator (B5) is not lit, then the TV set is powered off. You must press the TV set front panel MAIN POWER button (B1). If a picture does not appear, then the stand-by indicator will be red. In this case, use the remote control as indicated in 1). 3) If stand-by indicator (B5) is flashing red, and green then the TV set is in child-lock mode. It is necessary to use the remote control POWER button (A1), NUMBER 0....9 buttons (A3), or PROGRAM UP (A6) / DOWN (A21) buttons. The front panel PROGRAM UP/DOWN buttons (B9) will not function. Once on, the stand-by indicator turns to green and the picture appears on the screen. PR MENU PR SWITCHING OFF TV SET 1) Pressing the remote control POWER button (A1) ,you can switch off to stand-by mode (low power consumption mode) which also allows quick restart by remote control (see above: SWITCHING ON TV SET). 2) Pressing the TV set front panel MAIN POWER button (B1), you can completely power off the TV set. In this case, you must use the same front panel POWER button (B1) to switch on again (see above: SWITCHING ON TV SET). Remark: If a broadcast signal is not present after 30 minutes, the TV set will be automatically turned to stand-by mode. PROGRAM SELECTION (FROM 0 TO 99) Direct selection Use the remote control NUMBER 0....9 buttons (A3). For two digits program numbers, enter the second digit within 2 seconds. Up / Down selection Use the remote control PROGRAM UP (A6) / DOWN (A21) buttons or the TV set front panel PROGRAM UP / DOWN buttons (B9). SOUND CONTROL Volume adjustment Use the remote control VOLUME UP (A20) / DOWN (A7) buttons or the TV set front panel VOLUME UP / DOWN buttons (B8). MENU Mono forcing, dual language - If you are unable to get good sound quality for a program due to poor reception, you can force a change from stereo to mono transmission by pressing the remote control MODE button (A14). Then the program status display indicates "MONO" (in red). - On the other hand, during a program with dual language transmission, the MODE button (A14) allows you to toggle between the first and second language. The program status display will indicate "DUAL 1" or "DUAL 2" (plus NICAM according to the received signal). - To return to initial state, press again the MODE button (A14). Mute Mute the sound by pressing the remote control SOUND MUTE button (A2). Then, logo is displayed. The previous sound setting is returned after pressing the same button a second time. Sound effects A SPATIAL sound effect is available, using the remote control 3D (A13) button. The following display appears: SPATIAL Spatial sound effect Sound transmission mode Clock To return to initial sound effect, press again the 3D (A13) button. The following display appears: STEREO 11:11 STEREO 11:11 OFF No sound effect Sound transmission mode Clock 6 PICTURE CONTROL You can select three pictures settings, by using the remote control NORMAL button (A17) : - Normal I (standard hard picture) - Normal II (standard soft picture) - Favourite For other adjustments: brightness, contrast, colour, sharpness, use the Picture menu. If an NTSC signal is received, then a tint adjustment will also be available. PRO1 TF1 NORMAL I 11:11 PRO1 TF1 NORMAL II 11:11 PRO1 TF1 FAVOURITE 11:11 PROGRAM STATUS DISPLAY Channel number Clock PRO1 TF1 STEREO 11:11 Channel name Sound transmission Mode : Displayed in red colour only if forced to mono by MODE button (A14) Use the remote control RECALL button (A16) to display (for 4 seconds only) program status information. This display appears also after a program selection or after switching on the TV set. SLEEP FUNCTION The set will turn off (to stand-by mode) after a period of time that you can select. By repeated use of the remote control SLEEP button (A4), you can enter one of the following settings : OFF >20 min > 40 min >60 min >80 min >100 min >120 min >OFF. PRO1 TF1 STEREO SLEEP 18 Remaining time (minutes) before TV set switches off The SLEEP time remaining (before TV turn-off) can be seen again at any time by one touch on the remote control SLEEP button (A4). A second touch (while the status display is active) will modify the SLEEP time remaining. PICTURE FORMAT SELECTION If AUTO is chosen, the most appropriate format will be selected (subject to availability of broadcast wide screen signal information). Otherwise, the preferr ...