User manual DAEWOO DP-42WM

PLASMA DISPLAY USER'S MANUAL DP-42GM DP-42S M D P - 4 2 WM Proper use guarantees product life. Before using the product, be advised that you read this owner's manual well and try to operate it. - Product Warranty is included - DAEWOO ELECTRONICS CO., LTD. Features · 42" super-wide, 3.15" Ultra Slim Wall-mounting Monitor DAEWOO PLASMA opens new TV era with advanced plasma technology ­ 3.15 inches ultra slim Monitor. Light weight of only 66Lbs allows installing in narrow space. · DVD Direct Connection / Outstanding Picture Quality Digital Broadcasts Receive (SD Grade) DVD can be directly connected to the unit so that you can view clear digital images. You can enjoy even high quality images. by connecting digital broadcasting receiver with which digital broadcasts can be viewed. · PC Direct Connection PC can be connected to the PDP without a separate device, and can be used as a monitor so that the effect of presentation gets maximized, making it more popular in various events and exhibitions. · PDP Monitor with Minimized Noise Although PDP Monitor had an outstanding picture quality, there was a problem with the noise caused by cooling fan until now. DAEWOO PLASMA does not need cooling fan any more since it adopts self air circulation method with excellent heat transfer, eliminating the fan noise. · 160º Wide-Angle Viewing Area · Flat Panel with No Distortion and Color Blurring Since Plasma TV has no problems such as distortion, blurring, flickering unlike existing CRT type, you can enjoy Home Theater with super speaker. · Various Video Control - 11 Languages OSD - 20 Step screen zooming function - Full-screen still function - Various aspect ratio (16:9, Panorama, Normal, Enlarge LB, Enlarge LBS) · 3 Way 6 Speaker Stereo Sound System · Worldwide : NTSC, PAL, SECAM / Free Volt (100-240V 50/60Hz) This Owner's Manual presents safety precautions and how to use the product. After reading it thoroughly, use the product safely. Keep this manual where the user can see it easily. Failure to comply with warnings and cautions for the safe use of electric appliances may cause fire or human injury. 2 F C C R F I N T E R F E R E N C E S TAT E M E N T NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio, TV technical for help. - Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment, Safety Precautions Power Always obey all safety messages. · All the safety and operating instructions should be read before the product is operated. If anything strange happens, unplug this product from the wall outlet. · Do not disassemble or replace any parts of the monitor. Refer to a qualified service personnel for fepair. During a lightning storm, or when it is left unattended and unused for a long period of time, unplug it from the wall outlet. It can result in fire. When unplugging your monitor, always grip plug firmly and pull straight out from the receptacle. It can result in fire or electric shock due to damaged power cord. This product must be properly grounded. · Improper grounding may cause malfunction or electric shock. · When proper grounding is not possible, install circuit breaker. · Do not ground to gas pipe, water pipe, lightning rod, and telephone line. During a lightning storm, unplug the monitor from the wall outlet, and do not touch the antenna. It can cause fire or electric shock. WARNING You can be killed or seriously injured if you do not follow instructions. Installation Do not use this product in the neighborhood of a bath or shower. It can result in electric shock or fire. Do not place this monitor on an unstable cart, stand, or table It may cause the product and cart to overturn, damaging equipment or causing possible injury. 4 While Using Monitor Do not open cover (or back) because high voltage is present within the monitor's enclosure. It may cause electric shock. Never push objects of any kind into this product through openings at the back of monitor. It may cause fire or electric shock. No objects filled with liquids, such as vases, shall be placed on the monitor. Spilled liquids may cause electric shock or fire. Do not allow children to play or hang on the monitor. These actions may tip it over, causing personal injury. Do not place candle or lighted cigarette on the monitor. If these fall into the inside of the monitor, it may cause fire or explosion. Do not disassemble batteries, and do not allow children to swallow them. Heavy metal may contaminate environment, and can be harmful or detrimental to human health. (When children swallow the batteries, go to hospital and consult with a doctor.) Do not pray water to the monitor or wipe with damp cloth. Unplug the monitor from the wall outlet when smoke or strange smell occurs, then refer servicing to a service personnel. In the case of continuous use, it may cause fire or electric shock. It may cause electric shock or fire. 5 Safety Precautions Power Always obey all safety messages. · All the safety and operating instructions should be read before the product is operated. When moving your monitor, remove the power plug, antenna, and cables, and be sure to move it by more than two people.. Failure to follow this instruction can result in electric shock or personal injury. Do not touch the power plug with wet hands when plugging or unplugging. It can result in a risk of electric shock. CAUTION You can be injured or this product or any other your property can be damaged if you don't follow instructions. Installation Do not install where there is oil, smog, moist, and dust It may cause malfunction. Do not install the product where it will be exposed to the direct sunlight, and the product should not be near heat sources such as radiators, stoves, etc. It may cause malfunction. For proper ventilation, separate the product from the wall, and keep a distance of more than 4". Due to the increase of temperature inside the Monitor, it may cause fire. Do not place the monitor where ventilation is not ensured. Due to the increase of temperature inside the Monitor, it may cause fire. If you wish to install this product on the wall or ceiling, refer to the professional. Failure to do so may cause damage to product and injury to human. When using an outside antenna system, do not install it in the vicinity of overhead power lines. When antenna touches such power lines, it may cause electric shock. 6 During Use CAUTION You can be injured or this product or any other your property can be damaged if you do not follow instructions. Do not wipe the monitor using a cloth damped with chemicals (benzene, thinner, etc.). Monitor appearance may be marred. (Unplug the power plug and wipe with soft cloth.) Do not place the monitor near magnetic, speakers, or telephones. It can cause a change in the color tone of the screen. Do not place heavy objects or heat sources on the power cord. It may damage the power cord, causing fire or electric shock. Do not place any object or cover on the monitor. In an event of improper ventilation, the monitor will be overheated causing fire. When watching the TV, the distance between the Monitor screen and your eye should be as 5~7 times as the diagonal distance of the Monitor. Watching the TV for a long time may hurt your eye sight. When cleaning of the inside of the monitor is required, consult to the qualified service personnel. When the monitor is not cleaned for a long period of time, dust in it may cause fire or malfunction. When the monitor is placed on a cart or table, the front side of the Monitor should not project outward. Unbalance may cause the monitor to drop, resulting in personal injury or equipment malfunction and damage. Do not grip speakers when moving the monitor attached with speakers. When moving the monitor while gripping speakers, speakers may be fallea away from the monitor due to its weight, causing personal injury. 7 Checking Accessories Note Supplied Accessories Remote Control WER PO Check to be sure that the following items are packed with your Monitor. 1 UNIT Batteries (AAA) 2 UNITS T T INPU C LE SE AY PL DIS OM ZO + OM ZO U MEN VO L VO L EN RE SC ODE M ZE EE E UR FR PICTODE M D UN SO ODE M MUT E EE SL P AC Cable 1 UNIT PC(15pin) Cable 1 UNIT A/V Cable 2 UNITS Audio Cable 1UNIT 8 Note Optional Accessories Speakers DSP-SP20/SP21/SP22 - Speaker Main Unit Dimension : 3.94(W) x 24.72(H) 3.27(D)inch - Including Speaker Stand Dimension : 6.69(W) x 28.7(H) x 7.64(D)inch - Audio Amplifier : 8W + 8W - Impedance : 8 - Weight : 16.53Lbs The following items are optional accessories. Refer purchasing optional accessories from Daewoo Electronics Local Dealer or the dealer from where you purchased the unit. Table Top Stand DSP-ST20/ST21/ST22 - Dimension : 26.26(W) x 9.37(H) x 12.60(D)inch - Weight : 15.43Lbs Wall Mounting Unit DSP-HG10 · Variable Angles : 0º, 10º, 15º, 20º Speaker Main Unit · Dimension : 23.66(W) x 23.31(H) x 1.38(D)inch Including Stand · Weight : 9.92Lbs. 9 CONTENTS PREPARATION 4 · Safety Precautions 12 · Panel Controls 13 · Remote control BASICS 14 · Installation Instructions 15 · Connecting Speaker to PDP CONNECTION 16 · 18 · 20 · 22 · 24 · 26 · 28 · Watching Digital Broadcasts Watching Cable Broadcasts Watching Satellite Broadcasts Watching a DVD Image Watching a VCR Image Watching a Camcorder/Game Console Image Connecting PC APPLICATION 31 · 34 · 36 · 38 · 40 · 41 · 42 · 44 · 46 · 47 · 49 · Selecting Auto Picture Mode Adjusting Screen Size Adjusting Screen Position and Size Enlarging Screen Size Watching a Still Image Adjusting Auto Sound Mode Customizing Sound Mode Selecting INPUT SIGNAL Checking the Current Input Signal Selecting MENU Background Screen and Languages Setting Sleep Timer MISC. 50 · Before Requesting Service 51 · SPECIFICATIONS 11 Panel Controls Front Panel, Back Panel, Remote Control * Parts having same names in Plasma Display and Remote Control would function in exactly the same way. Front Power STAND BY/OPERATE · Power control sensor · Power Standby: Red - Standby Green - ON Power button Select when adjusting volume or select/adjust "MENU." Press when moving "MENU." Rear R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L AC IN SPEAKER(8 OHMS) PC INPUT COMPONENT A/V jacks (DTV/DVD INPUT jacks) Used when upgrading S-VIDEO, A/V INPUT, Cable Receiver INPUT jacks External Speaker Power 12 Remote Control ) indicates the page in which * The number in ( the function of each button is explained in detail. Note · Use two "AAA" batteries. · Be sure to use replacement batteries of the same type as the original ones. · The life of a battery depends on how much it has been used. INPUT SELECT POWER Input Select button 44 Power button 16 Used to select a desired input. Every press of the button cycles through the five different modes: Video 1 --> Video 2 --> PC --> Component 1 --> Component 2 ZOOM- DISPLAY ZOOM+ Pressing the Power button of the Monitor allows the Display to be standby. (Red light is shown in the Remote Control Sensor.) At this time, if you press the Power button of the Remote Control, the Display is turned ON (Green light in the Sensor). Display button Menu button 46 ZOOM button 38 MENU Indicates the current state and resolution. 42 Used to zoom the screen. To enlarge, press the (+) button, and to return to the previous condition, press the (-) button. (ZOOM Mode: Zoom 0~20) Use to display a desired menu. VOL VOL Menu Select button 32 Volume button Adjusts the volume. 32 Select Menu by pressing (Up), (Down), (Left), (Right) buttons. Screen Select button 31 PICTURE SCREEN MODE FREEZE MODE Aspect Ratio 40 34 Every press of the button cycles through the four different modes: Normal --> Cinema --> Dynamic --> User. Adjusts the size of the screen (normal, 16:8, etc.) Sound Mode button 41 Still SOUND MUTE MODE SLEEP Every press of the button cycles through the five different modes: Normal --> Movie --> Music --> News --> User. Used to view a still picture during watching moving images. (Sound can be heard.) Mute button Mutes sound. Sleep Timer 49 Each time you press this button, a different input mode appears. The sequence is as follows: 15 Min. --> 30 Min. --> 60 Min. --> 90 Min. --> 120 Min. --> OFF After the time is selected, it automatically becomes stand-by state. When Using Remote Control: Installing the Batteries in your Remote Control: · Be sure not to allow the Remote Control to drop or to become wet. · Keep it away from hot or moist locations. · To remove the cover, slide it outwards while pressing it down. · Place two batteries in the remote control by properly orienting them, then close the cover. 13 Installation Instructions When Using the Stand * When installing PDP Main Unit, be sure it is done by more than 2 professionals. * For detailed installation information, refer to the User's Manual, "STAND". 1 Take out the STAND from the package. 2 Smoothly fit the Stand to the Plasma Display Panel Separate the Cover Stand. (It is used when using for wall mounting, so store it.) 3 Engage the assembled stand with 4 screws (M5) enclosed. 4 Erect the Display M5 SCREWS (Assembled Picture) 14 Connecting the Speaker to the PDP 1 Connecting the Speaker to the Stand Be sure to check if there is a sponge attached to the surface on which the speaker is contacted. · By using a (-) driver or coin, fasten the special screw securely. Stand 2 Connecting the Speaker Cable · Connect one set (two cables) of the cable to the terminals on the back of the speaker in the way that red cable is for (+) terminal and black cable for (­) terminal. 15 Watching Digital Broadcasts Watching Digital Broadcasts · To watch digital broadcasts: - Purchase a separate digital Broadcasting Receiver(SET-TOP BOX) - Connect the PDP to a Cable Broadcasting Receiver that is provided by a company which retransmits digital broadcasts. 1 Connect a Digital Broadcasting Receiver to the PDP · Prepare A/V Cables supplied. · Connect the cables from the Digital TV Receiver output terminal to the PDP(Component 1, 2) input terminal. · When connecting the cables, be sure to match the cable colors. R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) L- AUDIO -R DTV/DVD INPUT Video Audio Digital Broadcasting Receiver (Set-Top Box) 2 Press the Power Buttons · Press the Power buttons of the PDP and the Receiver. 16 3 Input Select INPUT SELECT · Select [Component 1 or Component 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. · Each time you press the INPUT SELECT button, different input modes appear. The sequence is as follows: Component 1 --> Component 2 --> Video 1 --> Video 2 --> PC. Component1 Component2 PC Video1 Video2 4 Select a Desired Channel and Function · Select a desired channel and function by using the Remote Control of Digital Broadcasting Receiver. NOTES: 1) You can select INPUT SELECT while you are using OSD(Menu). Sequence: [Menu] --> [Input] --> [Component 1 or 2 (DTV/DVD)] 2) Digital Broadcasting signals available: 1080i(60Hz), 720p(60Hz), 480p(60Hz) 3) Antenna Connection: Apartment : Check if community antenna receives digital broadcasts. Private Houses: Set the indoor/outdoor UHF antenna to the direction of the digital broadcasting transmitting company. 4) For detailed connection method, refer to the Owner's Manual of Digital Broadcasting Receiver. 5) What is a component? : Signal with which brightness and color signals are separated, producing a sharp screen. 6) If the Digital Broadcasting Receiver has PC Output terminal (D-sub15pin), connect to `PC INPUT' at the back panel of the PDP. When watching the PDP by PC Input, some undesired signals may be seen at the top and bottom area of the screen. In this case, select [Menu] --> [Screen] --> [Vertical Size] to adjust. 17 Watching Cable Broadcasts Connect a CABLE Broadcasting Receiver to the PDP. · Prepare the A/V connecting cable. · Connect the receiver(Output) to PDP(Video Input) as shown below. · When connecting to an external AV source, be sure to match the colors. Watching Cable Broadcasts · To watch cable broadcasts, subscribe to your local Cable TV Broadcasting, and then, connect the digital set-top box for cable TV to the PDP as shown below. 1 R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) S-VIDEO VIDEO L- AUDIO -R VIDEO INPUT Video/Audio Cable Broadcasting Receiver 2 Press the Power Buttons · Turn the PDP and the Receiver ON. 18 3 Input Select INPUT SELECT · Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. · Each time you press the INPUT SELECT button, different input modes appear. The sequence is as follows: Video 1 --> Video 2 --> PC --> Component 1 --> Component 2. Video1 Component2 Video2 PC Component1 4 Select a Desired Channel and Function · Select a desired channel and function by using the Remote Control of the Cable Broadcasting Receiver. NOTES: * If your local cable company re-transmits digital broadcasts, you may watch normal broadcasts and digital broadcasts simultaneously. For detailed information, refer to your local satellite company. 19 Watching Satellite Broadcasts Connect a Satellite Broadcasting Receiver the PDP. · Prepare the A/V connecting cable. · Connect the receiver(Output) to PDP(Video Input) as shown below. · When connecting to an external AV source, ................... Watching Satellite Broadcasts · To watch satellite broadcasting, subscribe to a Digital Satellite Broadcasting, then connect the digital set-top box for satellite broadcasting to the PDP as shown below. 1 R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) S-VIDEO VIDEO L- AUDIO -R VIDEO INPUT Video/Audio Satellite Broadcasting Receiver 2 Press the Power Buttons · Turn the PDP and the Receiver ON. 20 3 Input Select INPUT SELECT · Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or PDP unit. · Each time you press INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 --> Video 2 --> PC --> Component 1 --> Component 2. Video1 Component2 Video2 PC Component1 4 Select a Desired Channel and Function · Select a desired channel and function by using the Remote Control of the Satellite Broadcasting Receiver. NOTES: * Picture quality of the Digital Satellite broadcasts is SD grade, and its aspect ratio is 16:9. 21 Watching a DVD Image Watching a DVD Image · Component Input is set to 480i and 480p mode. · Connect the cable from the DVD Video Output (Y, Pb/Cb, Pr/Cr) to the Component Input at the back PDP, and connect the cable from DVD Audio output (Left, Right) to the Audio Input at the back of PDP. 1 Connect a DVD Player to the PDP. · Prepare the AV cable. · Connect the DVD(Output) to the PDP(Component or Video Input) pas shown below. · When connecting to an external AV source, match the colors. R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R DTV/DVD INPUT VIDEO INPUT Video Audio S-Video Video/ Audio DVD DVD 2 Press the Power Buttons · Turn the PDP and the DVD ON. 22 3 Input Select INPUT SELECT · Select [Component 1 or Component 2, Video1, Video2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. · Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Component 1 --> Component 2 --> Video 1 --> Video 2 --> PC. Component1 Component2 PC Video1 Video2 4 Select a Desired Title and Function · Select a desired title and function by using the Remote Control of the DVD. NOTES: 1) Y/Cb/Cr, which stauds for DVD Player's Output Terminal, can also be written as Y/B-Y/R-Y, Y/Pb/Pr depending on the kinds of DVD devices. 2) The way of connecting the DVD to the PDP is as follows: Y <---> Y Cb <---> Pb, B-Y, Cr <---> Pr, R-Y 3) The DVD output can be made by Video, S-Video and or Component Video depending on the DVD devices. There are various output modes, so be sure to check when to purchase it. 4) When connecting S-Video and normal Video simultaneously, only S-Video will be displayed on the screen. 23 Watching a VCR Image Watching a VCR Image · Video can use either the normal video terminal or the S-video terminal. 1 Connect a VCR to the PDP. · Prepare the AV cable. · Connect the Video(Output) to PDP(Video Input) as shown below. R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) S-VIDEO VIDEO L- AUDIO -R VIDEO INPUT S-Video Video/Audio VCR 2 Press the Power Buttons · Turn the PDP and the VCR ON. 24 3 Input Select INPUT SELECT · Select [Video 1 or Video 2] by pressing the INPUT SELECT button of Remote Control or PDP unit. · Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 --> Video 2 --> PC --> Component 1 --> Component 2. Video1 Component2 Video2 PC Component1 4 Select a Desired Title and Function · Select a desired title and function by using the Remote Control of the VCR. NOTES: 1) When connecting a Video, the S-Video terminal provides a better image than the normal Video terminal. 2) When connecting to the normal video terminal, connect 3 color AV cables (video, left audio, right audio) to the PDP; for the SVideo terminal, connect the Audio terminal (Left, Right) in the same way, and connect the Video terminal by the S-Video cable (sold separately). 3) When connecting the normal Video terminal and the S-Video simultaneously, the S-Video terminal is selected. This can be checked by the [Display] button of the Remote Control. 25 Watching a Camcorder/Game Console Image Connect a Camcorder/Game Console to the PDP. · Prepare the AV cable. · Connect the Video(Output) to the PDP(Video Input) as shown below. · When connecting to an external AV source, match the colors. Watching a Camcorder/Game Console Image · Enjoy images recorded by camcorder or the game console after connecting to the PDP. 1 R AUDIO L PC INPUT UPGRADE PORT L- AUDIO -R S-VIDEO VIDEO L- AUDIO -R R DTV/DVD INPUT VIDEO INPUT L SPEAKER(8 OHMS) S-VIDEO VIDEO L- AUDIO -R VIDEO INPUT