User manual DEI AUTOMATE AM5 - Owners Guide

Model AM5 Owner's Guide limited lifetime consumer warranty Directed Electronics, Inc. promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed Electronics, Inc. unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed Electronics dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed Electronics dealer; and the unit is returned to Directed Electronics, Inc., shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed Electronics, Inc., in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED ELECTRONICS, INC. NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED ELECTRONICS, INC. DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED ELECTRONICS, INC. SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED ELECTRONICS, INC. IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE © 2005 directed electronics, inc. all rights reserved i AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS, INC. OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED ELECTRONICS, INC. SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED ELECTRONICS DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED ELECTRONICS, INC. SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized Directed Electronics dealer for details of the plan or call Directed Electronics, Inc. Customer Service at 1-800-876-0800. Directed Electronics, Inc. security systems, including this unit, are deterrents against possible theft. Directed Electronics, Inc. is not offering a guarantee or insurance against vandalism, damage or theft of the automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without limitation, liability for theft, damage and/or vandalism. Directed Electronics, Inc. does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this security system. Make sure you have all of the following information from your dealer: A clear copy of the sales receipt, showing the following: Date of purchase Your full name and address Authorized dealer's company name and address Type of alarm installed Year, make, model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile Installation receipts © 2005 directed electronics, inc. all rights reserved ii contents limited lifetime consumer ..... disarming without a . . . . . . . . transmitter . . . . . . . . . . . . . . . .7 valet mode . . . . . . . . . . . . . . .9 remote valet . . . . . . . . . . . . . .9 panic mode . . . . . . . . . . . . . .10 auxiliary mode . . . . . . . . . . . .10 multi-level security arming . . .10 long term event history . . . . .11 nuisance prevention® circuitry . .12 diagnostics . . . . . . . . . . . . . . . . .13 arming diagnostics . . . . . . . .13 disarming diagnostics . . . . . .14 table of zones . . . . . . . . . . . .14 rapid resume logic . . . . . . . . . . .15 programming options . . . . . . . .15 glossary of terms . . . . . . . . . .17 notes . . . . . . . . . . . . . . . . . . . . . .18 warranty . . . . . . . . . . . . . . . . . . . .i trademarks and copyrights . . . . .1 what is included . . . . . . . . . . . . . .2 important information . . . . . . . . .2 system maintenance . . . . . . . . . . .2 your warranty . . . . . . . . . . . . . . . .3 fcc/id notice . . . . . . . . . . . . . . . . . .3 standard transmitter . . . . . . . . . . configuration . . . . . . . . . . . . . . . .4 using your system . . . . . . . . . . . . .5 manual (active) arming . . . . . .5 automatic (passive) arming . . .5 silent mode . . . . . . . . . . . . . . .6 armed protection . . . . . . . . . . .6 disarming . . . . . . . . . . . . . . . .7 trademarks and copyrights Code-HoppingTM, Directed®, Doubleguard®, FailSafe®, Nuisance Prevention® Circuitry, Silent ModeTM, Soft Chirp®, Stealth CodingTM, Stinger®, Valet®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics, Inc. © 2005 directed electronics, inc. all rights reserved 1 what is included Control module and harnesses A Stinger® dual stage shock sensor (on-board the control module) Two 4-button transmitters Pre-wired Valet button with integrated red status LED HF Plus receiver Failsafe® Starter Kill relay (if equipped) important information Congratulations on the purchase of your security system. Due to the complexity of this system, it must be installed by an authorized dealer only. Installation of this product by anyone other than an authorized dealer voids the warranty. All dealers are provided with a preprinted dealer certificate to verify that they are authorized. By carefully reading this Owner's Guide prior to using your system, you will maximize the use of this system and its features. You can print additional or replacement copies of this manual by accessing the Directed web site at www.directed.com. system maintenance The system requires no specific maintenance. Your remote control is powered by a small, lightweight 3 volt lithium battery (CR2032) that will last approximately one year under normal use. When the battery weakens, operating range will be reduced and the LED on the remote will dim. 2 © 2005 directed electronics, inc. all rights reserved your warranty Your warranty registration must be returned and the bar code serial number must not be removed. If the warranty registration is not returned, you do not have a warranty. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. Make sure that you receive the warranty registration from your dealer. fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Directed Electronics, Inc. HF Plus Tested to Comply with FCC Standards © 2005 directed electronics, inc. all rights reserved 3 standard transmitter configuration controls the Arm and Multi-level arming function. controls the Disarm. controls Auxiliary channel 2 output and Silent Mode controls Panic mode. and pressed together controls channel 3 output. and pressed together control channel 4 output. 4 © 2005 directed electronics, inc. all rights reserved using your system manual (active) arming The factory default is active arming. In this mode you can activate, or arm, the system by pressing the button on your transmitter. When the system arms, you will hear a short horn honk and see the parking lights flash once. While the system is armed, the status LED will flash about twice a second, showing that the system is actively protecting your vehicle. If you hear a second short horn honk after arming, and see the status LED flashing in groups, see Diagnostics section. This extra short horn honk is called Bypass Notification. automatic (passive) arming The system also can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system "sees" you leave the vehicle by opening and closing a door. Whenever the system is in its 30-second passive-arming countdown, the status LED will flash twice as fast as it does when the system is armed. When the system arms, you will hear a short horn honk and the parking lights will flash once. The doors lock (if connected and programmed for passive locking). note: Passive arming may qualify for a higher insurance discount. Check with your insurance agent © 2005 directed electronics, inc. all rights reserved 5 note: If any protected entry point (such as a door or a switchprotected trunk or hood) is open, the system will not passively arm. Additionally, each time a sensor is triggered during the arming countdown, the 30-second countdown starts over. silent mode To temporarily turn off the arm or disarm chirps, use Silent ModeTM. Simply press for less than one second before arming or disarming, and the confirmation chirp(s) will be eliminated for that one operation only. If you want the arm/disarm chirps turned off permanently, your dealer can do this for you. note: The Warn Away® response to lighter impacts is bypassed if the system is armed using Silent Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free. The system is still fully capable of triggering. Only the Warn Away® response is bypassed. armed protection When armed, your vehicle is protected as follows: Light impacts to your vehicle will trigger the warn away signal. The system will pulse the horn and flash the parking lights for a few seconds. Heavy impacts will trigger the system. The triggered sequence is 30 or 60 seconds of constant horn honking and flashing parking lights. If a door is opened, the system will immediately start pulsing the horn and flashing the parking lights. Three seconds later, the horn output changes to a continuous blast. This progres- 6 © 2005 directed electronics, inc. all rights reserved sive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the system is armed, while still providing instant response (even if the door is immediately closed). note: If programmed for instant trigger, the horn will output full trigger response after the door has been opened (see Programming Options) Turning on the ignition key triggers the same progressive response as opening a door. If equipped, the starter interrupt prevents the vehicle's starter from cranking. note: the vehicle may already be equipped with a starter kill relay from the factory. disarming To disarm the system, press the button on your transmitter. The horn will sound twice, and the parking lights will flash twice. If the horn sounds either four or five times when disarming, refer to the Diagnostics section of this guide. This is called Tamper Alert. disarming without a transmitter This feature allows you to override the system without the transmitter should it be lost, damaged or disabled. To do this, you must have the vehicle's ignition key and know where the integrated LED/Valet button is located. The Valet button is activated by pressing the LED status indicator. © 2005 directed electronics, inc. all rights reserved 7 Integrated LED/Valet® switch LED status indicator Turn the ignition to the "run" position. Press and release the integrated LED/Valet button, within 10 seconds. After a few seconds the LED will stop flashing and the vehicle should start. If it does not, you may have waited too long. Turn the ignition off and try again. note: The setting for the number of times the integrated LED/Valet switch must be pressed is set in the Programming Section of this guide. DRW-35 8 © 2005 directed electronics, inc. all rights reserved valet mode You can prevent your system from arming, by using Valet Mode. This is very useful when washing the vehicle or having it serviced. In Valet Mode, the system will not arm, even with the transmitter, but all convenience functions (door locks, trunk release, etc.) will work normally. To enter or exit Valet Mode with the integrated LED/Valet button: Turn ignition to "on" position, then turn to "off" position. Press and release the integrated DRW-35 LED/Valet button within 10 seconds. The status LED will light steady if you have entered Valet Mode. To exit Valet Mode, repeat the steps above. The LED will turn off when exiting Valet Mode. remote valet Remote Valet is a convenient feature that makes bypassing the security system easier. This feature makes it possible to exit or enter Valet Mode using your factory keyless transmitter. 1. 2. 3. 4. Open any door. Press Press Press on the transmitter. on the transmitter. on the transmitter. The status LED will stay on if you have entered Valet Mode, and it will go out if you exited Valet Mode. © 2005 directed electronics, inc. all rights reserved 9 panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter. Just press for two seconds to enter Panic Mode. In Panic Mode, the horn will honk and the parking lights will flash for 30 seconds. To stop Panic Mode at any time, press on the transmitter again. note: In order for Panic Mode to be effective, the vehicle's horn (or optional siren) as well as the vehicle's parking lights must be connected. auxiliary mode The button on your transmitter, allows you to operate an auxiliary device, usually this is programmed to open the trunk. multi-level security arming The system allows you to select which of the inputs or sensors will be active or bypassed at the time the system is armed. Pressing the button on your transmitter more than once within 5-seconds of arming the system activates Multi-Level Security Arming. Each time the button is pressed (within 5-seconds) a different security level is selected. These security levels are listed below. 10 © 2005 directed electronics, inc. all rights reserved Lock Button pressed X times Once Twice Three Four Five Number of Horn chirps 1 chirp 2 chirps followed by long chirp 3 chirps followed by long chirp 4 chirps followed by Armed State with Zone(s) Bypassed All zones active Zone 2 bypassed Zone 4 bypassed Zone 2 & 4 bypassed long chirp 5 chirps followed by All zones bypassed, long chirp except zone 5 (ignition) long term event history The system stores the last two alarm triggers in memory and can be displayed by: With the ignition off, press and hold the integrated LED/Valet button. DRW-35 While holding the integrated LED/Valet button, turn the ignition on. Release the integrated LED/Valet button. Then press and release the integrated LED/Valet button within 5-seconds. DRW-35 © 2005 directed electronics, inc. all rights reserved 11 The LED will flash in two groupings representing the last 2 zones triggered. For example, if zone 2 and 3 were the last two triggered, the LED would flash two times followed by a pause then it would flash three times followed by a pause. Turn off the ignition switch or wait one minute to exit the history display. nuisance prevention® circuitry Your system has Nuisance Prevention® Circuitry (NPC). This circuitry prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder, jackhammers, airport noise, etc. Here's how it works: The alarm triggers three times. Each time, the same sensor or switch is triggering the alarm. The three triggers are within 60 minutes of each other. Your system will interpret this pattern of triggers as false alarms. After the third trigger, your system ignores, or bypasses, that sensor or switch (along with any other sensors or switches sharing the same zone) for 60 minutes. If the bypassed sensor tries to trigger the system while it is being bypassed, the 60-minute bypass period will start over. This ensures that a sensor that is continuously triggering will remain bypassed. Doors are covered differently: If the alarm is triggered by an open door for three full cycles (one-and-one-half minutes), the doors will be bypassed until the trigger ceases. 12 © 2005 directed electronics, inc. all rights reserved note: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the ignition. If testing your system, it is important to remember that this circuitry can cause zones to be bypassed and appear to stop working. If five chirps are heard when disarming, false alarm protection has engaged. If you wish to clear the memory, turn the ignition key on. diagnostics The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it. It detects any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. arming diagnostics If the system is armed with an input active (door open, sensor triggering, etc.) the unit will emit a short honk once when arming and then one more time a few seconds later. This is called bypass notification. note: Bypass notification will not occur if chirps have been programmed OFF. The system will ignore the input that was active when it was armed until it goes away. Three seconds later it will monitor that input normally. For example, if your car has interior light exit delay, and you arm the system before the interior light goes out, you may get bypass notification. Once the light goes out, however, the doors are monitored normally 3-sec© 2005 directed electronics, inc. all rights reserved 13 onds later. disarming diagnostics Extra disarm horn honks are the tamper alert. If four short horn honks are heard when disarming, the system was triggered in your absence. If five short horn honks are heard, a zone was triggered so many times that false alarm prevention circuitry has bypassed that zone. In either case, the status LED will indicate which zone was involved (see Table of Zones section). The system will retain this information in its memory, and the horn honks four or five times each time it is disarmed, until the next time the ignition key is turned on. table of zones The zone number is the number of LED flashes used by the system to identify that input. The standard input assignments are listed below. ZONE (Number LED Flashes) DESCRIPTION Instant trigger - often used for hood/trunk pin switches Instant trigger - a heavier impact detected by the shock sensor Door switch trigger Optional sensor Ignition trigger 1 2 3 4 5 The LED will not report if the Warn Away response is triggered. 14 © 2005 directed electronics, inc. all rights reserved rapid resume logic This system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. programming options Programming options control your system's normal, operational set-up. Most options do not require additional parts, but some may require installation labor. programming settings The following is a list of the program settings, with the factory settings in bold: first menu 1. 2. 3. 4. Active or passive arming (automatic arming 30-seconds after closing the last door). Arming/disarming confirmation short horn honks on or off. Door Trigger Error Short Horn Honk on or off. Ignition-controlled domelight on or off. 15 © 2005 directed electronics, inc. all rights reserved 5. 6. 7. Panic/Auxiliary Channel: Not applicable. Auxiliary Output or Delayed Auxiliary Output: Not applicable. Door Trigger delayed or instant: In the delayed configuration the unit will provide a progressive response if the door is opened while the system is armed. The system will chirp and the parking lights will flash for a few seconds followed by a full trigger response when the door is opened. In the instant mode, the system will trigger the full trigger response. 8. 9. Sensor shunt zones 1, 2 and 4 or All zones. Siren duration - 30 seconds or 60 seconds. LED/Valet button required to disarm the security system are programmable from one to five pulses. The default setting is one pulse. 10. Valet Pulse Count: The number of pulses of the integrated 11. Horn pulse honk duration 0.020 seconds or 0.030, 0.040, 0.050 seconds. second menu 1. 2. 3. 4. 5. 6. 7. Ignition-controlled door locking on or off. Ignition-controlled door unlocking on or off. Active or passive locking. Door lock pulse duration 0.8-seconds or 3.5-seconds Single or double unlock pulse. Channel 3 validity or second unlock. Code hopping on or off. 16 © 2005 directed electronics, inc. all rights reserved glossary of terms Control Module: The "brain" of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the alarm's functions. Failsafe® Starter Kill (if equipped): An automatic switch controlled by the security system which prevents the vehicle's starter from cranking whenever the system is armed. The vehicle is never prevented from cranking when the system is disarmed, in Valet Mode, or should the starter kill switch itself fail. Your system is ready for this feature, however installation of this feature may require additional labor. Input: Any physical connection to the security system. An input can be provided through a sensor, pinswitch or by existing systems in the vehicle, such as ignition or courtesy lights. Integrated LED/Valet button: A small push-button switch with an integrated Red LED mounted somewhere in the vehicle. The button is used to override the alarm when a transmitter is lost or damaged, or to put it into Valet Mode. The LED indicates the status of your system. It is also used to report triggers and faults in the system or sensors. This switch is also used to program optional features. Warn Away® Response: Light impacts to the vehicle generate the Warn Away® Response, which consists of several seconds of horn chirps and flashing parking lights. Zone: A zone is a separate input that the alarm can recognize as unique. Each input to the system is connected to a particular zone. Often, two or more inputs may share the same zone. © 2005 directed electronics, inc. all rights reserved 17 notes 18 © 2005 directed electronics, inc. all rights reserved Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. Panic Mode QUICK REFERENCE GUIDE: To arm the system To arm the system, press the button on your transmitter. When the system arms, your will hear a short horn honk, see the parking lights flash once, and the doors will lock. To disarm the system To disarm the system, press the button on your transmitter. You will hear two short horn honks, the parking lights will flash twice, and the doors will unlock. Disarming without a transmitter Turn on the ignition. Press the integrated LED/Valet button the programmed number of times within 10 seconds. The system should now disarm. If it does not, you may have waited too long. Turn the ignition off and on and try again. To enter or exit Valet Mode Turn ignition to "run" position, then turn to "off" position. Press and release the integrated LED/Valet button within 10 seconds. The status LED will light solid if you are entering Valet Mode, and it will go out if you are exiting Valet Mode. Remote Valet Open any door. Press the button on your transmitter. Within one second, press the button on your transmitter. Within one second, press the button on your transmitter again. The status LED will stay on if you have entered Valet Mode, and it will go out when exiting Valet Mode. To enter Panic mode, press the button on your transmitter. The horn will sound and the lights will flash for 30-seconds. To stop panic mode press the , , or button on your transmitter. © 2005 directed electronics, inc. all rights reserved 19 The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, DIRECTED is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world. Call (800) 274-0200 for more information about our products and services. Directed Electronics is committed to delivering world class quality products and services that excite and delight our customers. Directed Electronics, Inc. Vista, CA 92081 www.directed.com © 2005 Directed Electronics, Inc. - All rights reserved G436A 05-05