User manual DEI ORION C5.2

INTRODUCTION Thank you for your purchase of the Orion C-Series Component Loudspeaker system. These speakers offer an incredible value of performance. Titaniumcoated polymer cone midranges use an oversized 4 ohm voice coil for increased power handling and performance. The computer optimized crossover perfectly matches the midrange and tweeter for a seamless response. The passive crossover also offers an optical protection circuit for the tweeter to protect it from potentially damaging signals. The 1" ceramic dome tweeter offers a smooth extended frequency response and incorporates flush, surface and angle mounting hardware for optimal sonic as well as cosmetic results. The midranges are available in standard 5-1/4" and 6-1/2" sizes to fit most applications. PRACTICE SAFE SOUNDTM Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High powered automotive sound systems can generate sound pressure levels in excess of 130dB. When playing your system at high levels, please use hearing protection and prevent long term exposure. Your Product Information Serial Number: Model Number: Date of Purchase: WHAT'S IN THE BOX Included in this box are all the necessary mounting hardware and cables for your basic installation. Listed below is a detailed list of the components included in this system package. Quantity Description 1 Installation and Operation Manual 2 C-Series Tweeter Elements 2 Surface mount hardware 2 C-Series midrange 2 Passive crossovers 2 Cables (speakers to crossover) 2 Cables (crossover to amplifier) 1 INSTALLATION The performance of the C-Series component loudspeaker is directly proportional to the quality of installation. Care taken during the installation process will be rewarded with years of satisfying performance. If you are unsure about your installation capabilities, please refer to your local Authorized Orion Dealer for technical assistance. Orion dealers are trained professionals dedicated to extracting the maximum performance from of your Orion system. If you decide to install this speaker system yourself, please read the entire installation section before starting your installation. TOOLS OF THE TRADE Listed are the majority of the tools required to perform the installation. Having the proper tools will make the installation much easier. It is very difficult when you get half way through the installation and discover that you require a specific tool to get yourself through a particular part of the installation. Some of these tools are necessities. Some make the job much easier. · · · · · · · · · · · · · (4" woofer installation) · Hole Saw Arbor · 47/8" Hole Saw (5" woofer installation) · 55/8" Hole Saw (6" woofer installation) · 13/4" Hole Saw (for flush and angle mount 1/ " Drill Bit 4 1/ " Drill Bit 8 3/ " Drill Bit 8 33/4" Hole Saw Marking Pen Electric Drill Phillips Screwdriver Volt/Ohm Meter (Optional) Assorted Tin Snips Needle Nose Pliers Wire Cutters Wire Crimpers Wire Strippers tweeter installation) FINDING SPEAKER MOUNTING LOCATIONS Choosing the correct speaker locations will have the greatest effect on the sound quality of the system. There are many different considerations needed when choosing the locations that best suit your needs. The locations must be large enough for the speakers to fit. Care is needed to ensure that the location you have chosen will not affect any of the mechanical or electrical operation of the vehicle. Determining the best location for the speakers will depend on your cosmetic needs and your vehicle's interior. If minimal intrusion in your vehicle is desired, factory speaker locations may be the ticket for you. Placing the speaker in the factory location can often give very desirable results. DOOR MOUNTING When checking for possible speaker locations in the doors, check the operation of the window and all assemblies. There is also a stabilizer stop bar in between the door and the door jamb. This bar prevents the door from opening too far. Many shade tree installers overlook this and check for clearance only when the door is fully open. 2 REAR DECK MOUNTING In rear deck installations, check the operation of the trunk suspension springs or tension bars. These tension bars move in the opening and closing of the trunk. You cannot be too cautious during this part of the installation. In addition, do not locate the speakers too close to the back of the rear deck. Installing the far screws may not be possible without removing the rear window. INSTALLING THE MIDRANGE Step 1: Determine where the speaker will be mounted. Make sure there is a flat area large enough for the speaker to fit properly. An uneven mounting surface can damage the driver. Step 2: Check to make sure the space you have chosen for the speaker will not interfere with the operation of the vehicle. Step 3: Using the supplied template guide, mark the hole with a pen. Step 4: Cut the hole for the speaker. When using correct sized factory locations, this step can be passed. A hole can be cut either with a pair of metal tin snips, an air or jig saw, or with a hole saw corresponding to the size of the midrange listed below. · 4-7/8" Hole Saw (5" woofer installation) · 5-5/8" Hole Saw (6" woofer installation) WARNING: Window mechanisms and electrical wires have a nasty habit of hiding where you least expect. CHECK BEFORE YOU DRILL! Step 5: Run the speaker wire to the speakers. Make sure to keep wires away from sharp metal or other edges. When passing through metal ,use a protective grommet. Step 6: Using the plastic grille ring as a template, mark the mounting holes with a pen. Step 7: Pre-drill mounting holes using a 1/8" drill bit. WARNING: Window mechanisms and electrical wires have a nasty habit of hiding where you least expect. CHECK BEFORE YOU DRILL! Step 8: Pull the wire through the speaker opening and connect to the speaker. Be sure to observe proper midrange polarity during this process. 3 Step 9: Mount the speaker- The speaker is placed in the grille ring from the front. Place the speaker and the grille ring in the installation hole. Align the mounting screw holes and drive in the four mounting screws. Push the perforated metal grille back into the grille ring. INSTALLING THE TWEETER SURFACE AND ANGLE MOUNTING Step 1: Determine where the tweeter will be mounted. Make sure there is a flat area large enough for the tweeter to fit properly for surface or angle mounting. Step 2: Check to make sure the space you have chosen for the speaker will not interfere with the operation of the vehicle. Step 3: Pre-drill mounting holes using a 1/8" drill bit. WARNING: Window mechanisms and electrical wires have a nasty habit of hiding where you least expect. CHECK BEFORE YOU DRILL! Step 4: Drill a 3/8" hole for the tweeter wire. If drilling through a metal surface, use a grommet to protect the wires. Step 5: Run the tweeter wire through the wire hole and attach the wires. Be sure to observe proper polarity during this process. Step 6: Mount the tweeter housing using the supplied hardware. Step 7: Place tweeter in housing Step 8: Install beauty ring placing on housing over tweeter and rotate it clockwise. Surface Mount Angle Mount 4 FULLY FLUSH MOUNTING Step 1: Determine where the tweeter will be mounted. Make sure there is a flat area large enough for the tweeter and no obstructions behind the area. Step 2: Mark with a pen the hole needed for the tweeter. Step 3: Be sure the hole is large enough for the tweeter housing. Step 4: Cut the hole for the tweeter. When using factory locations, this step can be passed. A hole can be cut either with a pair of metal tin snips or a hole saw corresponding to the size of the tweeter listed below. · 1-3/4" Hole Saw WARNING: Window mechanisms and electrical wires have a nasty habit of hiding where you least expect. CHECK BEFORE YOU DRILL! Step 5: Install tweeter in flush mount housing. Step 6: Install tweeter and housing in the hole cut for mounting, so that the beauty ring is flat with the front of the surface. Step 7: Use the supplied mounting ring to secure the housing to the surface. INSTALLING THE CROSSOVER Step 1: Find a location for the crossover away from any factory or after market electrical wires. It is recommended to mount the passive crossover close to the amplifier. In the event you decide to upgrade and bi-amplify the system, mounting the passive crossover close to the amplifier would simplify the installation upgrade. Step 2: Remove top cover of crossover housing. Don't lose it. Step 3: Mark with a marking pen the two mounting holes. 5 Step 4: Remove crossover and pre-drill mounting holes using a 1/8" drill bit. WARNING: Gas tanks, fuel lines, brake lines and electrical wires have a nasty habit of hiding where you least expect. CHECK BEFORE YOU DRILL! Step 5: Mount the crossover using the supplied #8 screws. Step 6: Connect the wires. Make sure the speaker wires for the midrange go to the woofer output and the tweeter to the tweeter output. Be sure to observe the correct polarity. Changing the polarity may be necessary for optimum sound quality. Step 7: Re-install the crossover cover. SPECIFICATIONS Model Nominal Impedance Power Continuous/Maximum Frequency Response Sensitivity Mounting Depth Mounting Diameter Orion C5.2 4 ohms Orion C6.2 4 ohms 50/100 75Hz - 20kHz 89 dB 2.375" (59mm) 4.875" (124mm) 75/100 60Hz - 20kHz 90 dB 2.75" (71mm) 5.625" (144mm) 6 Warranty LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase from the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two-year period, there will be no charge for this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. If the unit is installed by anyone other than an authorized Directed dealer, the warranty period will be one year from the date of purchase by the dealer as indicated by the date code marking of the product. This warranty is non-transferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose, and does not cover damage to the unit caused by installation or removal of the unit. During this one-year period, there will be no charge for this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. This warranty is void if the product has been damaged by accident or unreasonable use, neglect, improper service or other causes not arising out of defects in materials or construction. Units which are found to be damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but may be replaced at the absolute/sole discretion of Directed. ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. Unit must be returned to Directed, postage pre-paid, with bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number, and address, authorized dealer's name and address, and product description. Note: This warranty does not cover labor costs for the removal and reinstallation of the unit. IN ORDER FOR THIS WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DIRECTED DEALER. ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER INSTALLATION WILL BE COVERED BY THE LIMITED 1 YEAR PARTS AND LABOR WARRANTY. Note: This warranty does not cover labor costs for the removal and reinstallation of the unit. BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA. © 2004 Directed Electronics, Inc. All rights reserved. G37101/06 05-04