I m p o r t a n t s a f e g u a rd s · Use this appliance only as described in this instruction manual. As with any electrical appliance, the instructions aim to cover as many eventualities as possible. Caution and common sense should be used when operating and installing this air conditioner. · This appliance has been manufactured to cool and dehumidify domestic environments and should not be used for other purposes. · It is dangerous to alter or modify the unit's characteristics in any way. · The appliance must be installed in line with the relevant national legislation. · Should repairs be necessary, contact the nearest authorized De'Longhi Repair Service Center. Unauthorized Delonghi servicing can be dangerous. · This appliance is to be used by adults only; keep away from children. · In the case that the power cord becomes damaged, this must be substituted only by specialized personnel authorized by the manufacturer. · Always ensure the appliance is grounded. If you have any doubts check with a qualified electrician. · Avoid using extension cords with the unit. · Before cleaning or maintenance operations, always unplug the unit from the outlet. · Do not pull on or place strain on the power cord when moving the appliance. · The appliance should not be installed where the atmosphere may contain combustible gases, oil or sulphur, or near heat sources. · Do not rest hot or heavy objects on the appliance. · Remember to perform the descaling procedure at the end of each season (see page 13). In areas where the water is particularly hard (rich in minerals), the use of a commercial descaling product added to the water is recommended. This can be requested to De'Longhi America, Inc. · Clean the filters at least once a week. · Avoid using heaters near the unit. · The unit, should be transported in a vertical position. If this is not possible secure the unit at an angle, do not lie it horizontally. · Before transporting the unit, drain the condensation collecting-tray and tank. After transportation, wait at least 1 hour before switching on the unit. · The packaging materials can be recycled. You are therefore recommended to place them in the special containers for differentiated waste collection. SAVE THESE INSTRUCTIONS 4 How does your Pinguino work Dur ing the summer, optimum comfort is achieved with a temperature of around 75°F (24 °C) and 50% relative humidity. An air conditioner removes moisture and heat from the room where it is located. One advantage of portable air conditioning units over window models is that they can easily be moved from one room to another in the home or even transferred between different buildings. The hot air in your room is passed through a coil cooled by refrigerant gas, removing excess heat and moisture before being discharged again into the room. In single unit models, the hot and moist air is discharged outside. 5 ENGLISH Setting up The following instructions will help you set up your air conditioning unit as efficiently as possible. AIR CONDITIONING WITHOUT INSTALLATION FOR INSTANT TEMPORARY USAGE With just a few simple operations, Pinguino will restore comfortable conditions in your room: · Fit the exhaust hose 25 to the coupling 8 on the back of the unit as shown in figure A. · With a double casement window, use the suction cups 27 provided to hold the two halves of the window together (fig. C). 1 2 C A · Fit the window attachment 26 to the end of the hose 25 . · Place the unit near a window or door. · Open the window, or the door slightly and place the window attachment 26 as shown in figure B. B · Pinguino is equipped with an adjustable window bracket 30 . If you have a sliding window, place the bracket on the window sill, extend the bracket fully within the window frame and lower the window onto the bracket. Insert the nozzle of the exhaust hose into the slot, then connect the hose to the air conditioner (Fig. D). With the wing nut it's possible to use the window bracket also for sliding windows. Position the hole of the bracket to allow a correct installation of the exhaust hose. D window bracket 6 Setting up If you have a sliding door, use the additional set provided 31 in order to extend the accessory to the desired length; joining the two parts (fig. E), adjust the total length according to your needs, then fit the bracket with the relevant nuts, close the door and connect the hose (fig. F). H E in a window pane 4" 100 in the wood sill of a window in the wall: for optimum results, insulate the section of the wall with suitable insulating material. · Fit the flange 24 supplied to the hole. · Fix the hose 25 to the coupling 8 on the back of the unit (figure A). · Attach the end of the hose 25 to the flange 24 as shown in the figure I. F AIR CONDITIONING WITH INSTALLATION For more efficient use Pinguino can also be semi-permanently installed (Fig, G) I MAX 47" (120 cm) MIN 12" (30 cm) 12" 30 cm When the hose 25 is not attached, close the hole with the stopper on the flange 24 . 12" G 30 cm To install, proceed as follows: · Make a hole in a outside wall or through the glass of a window. Check the height and dimensions given in figure H NOTE: When the unit is installed semi-permanently, we recommend leaving a door slightly open (1cm (1/2") is enough) to ensure an adequate exchange of air. 7 ENGLISH Pre p a ra t i o n f o r u s e HOW TO USE THE AIR CONDITIONER WITH WATER These air conditioners can use both air and water to cool the condenser (the hot part) of the air conditioner. To utilize the full potential of your air conditioner, the tank 5 needs to be filled with water. The water is used to increase the cooling power and reduce the noise level and energy consumption of the air conditioner. The water that is used is then expelled from the machine as water vapor through the exhaust hose 25 (it does not go into room). Always use clean tap water (which doesn't contain salts). As a rule the water will usually last about 8 hours, however this depends on the conditions within the room, such as temperature, humidity, insulation and number of people. In cool jet mode the water will also be used more quickly. 2 A) To open the front panel 3 grip the side panel and gently pull the panel towards you and upwards. Remove the tank 5 Lift it forward. B) Turn the tank upside down and remove the plug. Remove the extendable tube and fill the tank, leaving it on the ground. C) After completing the filling procedure, replace the extendable hose and the cap and screw it in tightly. Return the tank to its place, with the writing FRONT clearly visible. Carefully hold the panel in the center and lower to its closed position. During the "water functioning" operation and in particularly silent locations (e.g. the bedroom) a slight gurgling sound may be heard. This is completely normal. IN HIGH HUMIDITY CONDITIONS Water is extracted from the air in the room, this water is also used to cool the appliance. When the humidity is particulary high an excess of water may build up in the internal tank. This can be drained by removing the stopper from the drain hose 9 and draining into a suitable receptacle. IMPORTANT: If the room temperature is 90°F (32°C) or over the air conditioner must be operated with water in the tank. WARNING: Do not use water containing salt, eg. seawater or water treated using softening systems that utilize table salt. 8 Turning on and setting the timer ELECTRICAL CONNECTION Before plugging in check that: · the mains outlet corresponds to the power outlet shown on the rating plate; · the outlet and the mains lead correspond to the power requirements of the appliance ; · the plug should fit the outlet, otherwise have the outlet replaced; · the outlet is properly grounded. PROGRAMMED MODE 1) Set the operating times by pushing out the notches on the dial corresponding to the time required (each notch represents 15 mins.) 2) Press the TIMER key 12 , the signal light 14 will come ON. 3) Make sure that the timer indicates the correct time (see instructions on setting). The manufacturer cannot be held responsible for any damages due to failure in following normal safety procedures. Replacement of the power cord must be carried out by qualified personnel. Funzionamento operating time 11 10 9 4 SETTING THE TIMER The programmer/timer 13 , like all clocks, must be set to the exact time. If for example it is 4.00 pm., turn the dial in a clockwise direction (following the direction of the arrow) until the number 4 is lined up with the triangular pointer (the arrows indicates 4:00 P.M. approximately ). 4) Select the desired function as shown in the chart section. Note: To override the programmed operating times, simply press the ON/OFF key 12 (the timer signal light 14 will go out) 11 10 9 4 pointer Note: Never turn the dial in an counterclockwise direction! The timer is in effect an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or if there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. 9 ENGLISH Selecting functions AIR CONDITIONING FUNCTIONS To turn the unit on in air conditioning mode, proceed as follows: 1. Press the ON/OFF button 11 (the signal light 10 will come on). COOL JET The cool Jet mode provides the appliance with greater cooling capabilities. This is particularly useful when you want to bring the temperature of a very warm room quickly down to a more comfortable level. In this case: Make sure that the tank is full of water (see page 8); Make sure that the function selector switch 19 is in the HIGH position. 2. Rotate the function selector 19 dial counter-clockwise: · Place the function selector in the HIGH position to operate the unit in air conditioning mode at maximum fan speed, after 3 minutes the signal light 15 will come on. · Place the function selector in the LOW pos. to operate the unit in air condtioning mode at minimum fan speed after 3 minutes the signal light 16 will come on. 3. Now set the required temperature by rotating the room thermostat dial 20 . Press the Cool Jet button 22 , after three minutes , the signal light 21 , 15 or 16 with come on. After reaching the desired temperature, you can release the Cool Jet button and reposition the selector switch to the LOW position This will provided quite operation. VENTILATION/FILTRATION Rotate the function selector 19 clockwise. · Press the ON/OFF button 11 (the signal light 10 will come on). · Place the function selector on the "FreshZone" position and choose the desired fan speed (min/max). The signal light 17 18 or will come on). Note The temperature is not expressed in degrees. We recommend that you turn the thermostat dial to the maximum position. When the desired room temperature has been reached, slowly turn the thermostat in a clockwise direction until it arrives at the position where a click can be heard. The signal lights 15 (or 16 ) will turn off. The temperature selected in this way will automatically regulate and maintain the temperature and save energy. When regulating the thermostat, the air conditioning function is temporarily interrupted and the unit continues to operate in fan only mode. In this way, the appliance keeps the air temperature within the room constant. PROBLEM WARNING LIGHT 23 The pilot light indicates that the safety device of the pressure switch has switched on. In this case the appliance is deactivated. To restore the proper functioning of the appliance, eliminate the possible causes of the problem and press the restore button 6 . The causes may be: 1) Water has accumulated in the exhaust hose: in this case, it is necessary to drain the water out of the machine, outwards (never towards the air conditioner) and eliminate the water in the hose. 2) The exhaust hose is obstructed: eliminate the obstacles that obstruct the release of air to the outside. If, after having repositioned the drainage tube, the machine still does not start up, the problem might be more complicated (ex.: obstructed ventilation fan) and could require the assistance of a Delonghi Authorized Service Center. Delay on Start Up 1. A special safety device will delay the start of air conditionig by approximately 3 to 5 minutes when switching between functions or on initial start up. 2. You may also experience a slight delay between changing from one function to another. 10 Recommendations ELECTROSTATIC FILTration In addition to dust, this filtration system is able to capture even the smallest sized particles and impurities such as cigarette smoke. The electrostatic white filter should never be used with the permanent washable filter, (black) which is also included with the appliance. Therefore: A. If you wish to use the electrostatic filter: Remove the permanent washable filter from the filter housing; Remove the grille 7 (fig. M on page 12) and the per ...