User manual DIRECTV H20

" Cool! A highly defined guide for my high-definition satellite receiver. DIRECTV® HD Receiver user's guide rethink tv Safety & Care Your DIRECTV® HD Receiver has been designed and manufactured to stringent quality and safety standards. You should, however, be aware of the following important precautions for safe and optimal use of the equipment. Meaning of symbols printed on the rear panel of the product: · · The " bolt of lightning" indicates un-insulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The "exclamation point" calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. WARNING To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Important Safety Instructions 1) 2) 3) 4) 5) 6) 7) 8) 9) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. TIP We highly recommend plugging the DIRECTV Receiver into a surge protector to prevent damage from fluctuations in your power supply. IMPORTANT: Be sure not to place your DIRECTV Receiver near anything WET or HOT! 10) 11) 12) 13) 14) · CAUTION: Avoid moisture to reduce the risk of fire or electric shock. The DIRECTV Receiver should not be used near water (for example, kitchen sink, bathtub, pool, damp basement). Also, never spill liquid on the receiver, and do not place vases or other vessels containing liquid on top of it. · Ensure proper ventilation -- the vent slots on the DIRECTV Receiver must be left uncovered to allow proper airflow to the CAUTION: TO REDUCE THE RISK OF unit. Blocking the airflow to the unit could impair performance or damage your receiver and other components. ELECTRIC SHOCK, DO NOT REMOVE · Do not stack electronic components or other objects on top of the DIRECTV Receiver. Also, do not stack the receiver on top COVER (OR BACK). of a "hot component" such as an audio power amplifier. NO USER-SERVICEABLE PARTS INSIDE. · Protect your components from power surges by connecting all the components before plugging any power cords into the wall REFER SERVICING TO QUALIFIED SERVICE outlet. Use of a surge protector is also recommended. PERSONNEL. · Don't overload power outlets or extension cords, which can result in the risk of fire or shock. It's also important to use only the type of power source indicated on the marking label or in this manual. · To prevent electrical shock, this apparatus shall be connected to a mains socket outlet with a protective earthing and fully inserted. · Avoid audio hum or interference by inserting all cable plugs firmly into their jacks. Also, place Audio/Video (A/V) cables to the sides of the TV back panel rather than down the middle once connected. Try not to coil any twin-lead cables and keep them away from A/V cables as much as possible. · Never insert objects of any kind into any openings in the DIRECTV Receiver (other than the DIRECTV ® Access Card as detailed in this chapter). · Place it on a flat, hard surface -- do not operate the DIRECTV Receiver on a carpet or other padded surface. · Always unplug your DIRECTV Receiver before moving it. · Always unplug the DIRECTV Receiver, TV and other equipment before you connect or disconnect any cables. · Leave the main power connector accessible the mains connector at the back of the unit in case of emergency shutdown · CAUTION: Electric Shock -- never attempt to disassemble the DIRECTV Receiver yourself; always take it to a qualified service person when repair is required. Opening or removing covers may expose dangerous voltage or other risks, and incorrect reassembly can cause shock when receiver is subsequently used. Attempted self-repair may also void your warranty. Changes or modifications not expressly approved by the party responsible for compliance (by the warranty or by the manufacturer) could void the user's authority to operate the equipment. · Do not drop your DIRECTV Receiver and always move it with care. · Have your DIRECTV Receiver professionally serviced (do not attempt to service it yourself) · Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. · To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord. · Do not install this equipment in a confined space such as a book case or similar unit. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! For your information: · The identification sticker can be located underneath or on the back of your receiver. · The telecommunication network voltage used is the category number 3. Note to Satellite Dish Installer This reminder is provided to call your attention to articles 810 and 820 of the 2002 National Electrical Code. Refer to article 810, in particular 810-1 and 810-15, for required grounding of the metal structure of the dish antenna. Refer also to the 810-2 which, by reference to article 820, requires that the satellite dish coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as practical. iii Great TV viewing is in your hands! A good way to begin learning about your DIRECTV System is to familiarize yourself with the remote control. You'll find further details throughout the User Guide relating to specific functions. ® Keys in the shaded area below can be programmed to function with your VCR, DVD player or stand-alone DVR unit. MODE SWITCH POWER Changes remote to control other TV INPUT equipment, for example, a DVD Changes the "source" -- the piece of equipment whose signal is displayed on your TV AV1 AV2 TV Cycles through HD resolution and screen format options Turns your DIRECTV HD Receiver and other equipment on and off, as selected with MODE switch Turns your TV and DIRECTV HD Receiver on and off FORMAT STOP TV INPUT TV POWER ON/OFF TV POWER PWR FORMAT ON OFF ADVANCE PLAY FFWD Navigating 101 You'll find you can get around nearly all onscreen menus the same simple way. 4Highlight... a menu or button by using the ARROW keys (up, down, left and right). 4Choose it... by pressing SELECT while the item is highlighted. Note: Don't worry about getting stuck in a menu. You can always press EXIT to return to video. REPLAY REWIND R PAUSE E ID ACTIVE LIST RECORD EX For future use. SELECT ACTIVE Displays your To Do List LIST GU IT Displays the onscreen program Guide GUIDE BA CK MENU IN FO EXIT Exits any menu and returns to last channel viewed Move highlight to items in whatever direction needed Selects any highlighted item Takes you to the screen you visited previously SELECT BACK ARROWS INFO Displays info for a highlighted or fullscreen program VOL CHAN Quick Tip To place batteries in your remote control: 1. Remove cover from the battery compartment by sliding it downward. 2. Insert 2 AA batteries (supplied), matching the positive (+) and negative (­) at each end. 3. Slide the cover back on to complete installation. To program your remote control: 1. See "Programming Your Remote Control" on page 30. In Guide, jumps 12 hours back; other functions vary -- look for onscreen hints In Guide, jumps 12 hours forward; other functions vary -- look for hints onscreen Raises or lowers volume RED PAGE Displays a compact menu of settings and services MENU In live TV, displays the Mini Guide; other functions vary -- look for onscreen hints BLUE YELLOW MUTE PREV GREEN 1 4 GHI 2 ABC 3 DEF In fullscreen TV, cycles through alternate audio tracks; other functions vary -- look for onscreen hints VOLUME MUTE 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ In live TV, changes channel up or down; in a menu, such as the Guide, scrolls page up or down Tunes to last channel viewed Activates channel number entries quickly CHAN/PAGE PREV Toggles sound volume on/off Tune to a channel directly; also input numbers when needed in onscreen menus 0 DASH ENTER NUMBER KEYS & DASH ENTER " Welcome to the DIRECTV Family! Chapter 1 ­ Getting Started Welcome ..................................................................................................................................... 2 Making the Right Connections .................................................................................................. 3 About High-Definition ............................................................................................................... 4 Resolution & Interlacing ............................................................................................................. 6 Wide-Screen vs. Standard Formats ............................................................................................. 8 Hardware Reference .................................................................................................................. 13 Cables & Connections .............................................................................................................. 14 DIRECTV HD Receiver Front Panel ....................................................................................... 17 DIRECTV HD Receiver Rear Panel ........................................................................................ 18 Choose Your Setup.................................................................................................................... 20 Guided Setup & Activation ...................................................................................................... 28 Programming Your Remote Control ......................................................................................... 33 Options for Changing Video Output ........................................................................................ 34 Using Your IR/RF Remote to Control Your DIRECTV® HD Receiver ................................... 36 Receiving Local "Off-Air" Broadcast Channels ........................................................................ 37 This is the Table of Contents Chapter 2 ­ What's On Watching TV ............................................................................................................................ 41 The Guide ................................................................................................................................. 45 Autotune ................................................................................................................................... 47 Pay Per View ............................................................................................................................. 49 vi Chapter 3 ­ The Quick Menu Using the Quick Menu ............................................................................................................. 52 Settings ..................................................................................................................................... 52 Audio Options .......................................................................................................................... 54 Dolby Digital ........................................................................................................................... 55 Category Sort ............................................................................................................................ 56 Pay Per View ............................................................................................................................. 56 Find By ..................................................................................................................................... 57 Date & Time ............................................................................................................................ 58 Favorites .................................................................................................................................... 58 Caller ID & Messages ............................................................................................................... 59 Parental Controls ...................................................................................................................... 60 Pretty Simple, Right? Chapter 4 ­ Other Information Troubleshooting ........................................................................................................................ 66 Limited 90-Day Warranty ........................................................................................................ 77 Product Information ................................................................................................................. 82 DIRECTV PROTECTION PLAN ......................................................................................... 83 FCC Customer Information ..................................................................................................... 85 Index ......................................................................................................................................... 89 Icon Reference ..................................................................................................Inside Back Cover Important Important: This device incorporates an anticopy process technology that is protected by U.S. patents and other intellectual property rights. The anticopy process is licensed for non-commercial, home use only. Reverse engineering or disassembly is prohibited. Unauthorized changes or modifi cations to this equipment may void the user's authority to operate it. vii " Are you ready to watch totally cool, high-definition TV? We thought so. Chapter 1 Getting Started 2 3 4 6 8 13 14 17 18 20 28 33 34 36 37 Welcome Making the Right Connections About High Definition Resolution & Interlacing Wide-Screen vs. Standard Formats Hardware Reference Cables & Connections DIRECTV HD Receiver Front Panel DIRECTV HD Receiver Rear Panel Choose Your Setup Guided Setup & Activation Programming Your Remote Control Options for Changing Video Output Using Your RF/IR Remote to Control Your DIRECTV® HD Receiver Receiving Local "Off-Air" Broadcast Channels 1 Welcome With its astounding variety of channels and choices, crisp digital-quality picture and sound and oneof-a-kind sports and events, DIRECTV® HD service offers everything you'd want in your television experience. With the DIRECTV® HD Receiver you can expect more than ever before, with access to over 225 channels, including our awesome HD selections and over 30 premium movie channels, with something to please everyone in the family. DIRECTV Pay Per View offers a handy choice in recent hit movies, plus exciting live sports, concerts and specials, even Pay Per View selections in HD. There's exclusive sports subscriptions for every taste and team. Even access to 36 commercial-free music channels! To deliver this unique programming and enhance your entertainment experience, the DIRECTV HD Receiver has been designed to be simple and user-friendly. You'll find that most features are selfexplanatory, with onscreen directions to lead you through them. So, welcome to the family. TIP You can find additional information and the latest updates at DIRECTV.com. 2 Making the Right Connections Are you ready to connect your DIRECTV HD Receiver and your other components? Whether you're having your system professionally installed or handling it yourself, be sure to read over the following few pages to familiarize yourself with some important tips for safety and care. Before you begin Your satellite dish antenna must be installed before you can begin following the procedures in this User Guide. (Professional installation is highly recommended.) Your dish needs to be mounted in a position where it has access to the satellite signals, and RG-6 coaxial cables must be run into the room(s) where your receiver(s) will be located. If you choose to install the dish yourself, see the separate instruction manual that came with your satellite dish antenna. Package Contents The following items are included with your DIRECTV HD Receiver: 4 A/V cables (RCA type) 4 S-Video cable 4 Phone cord 4 Power cord 4 Access card 4 User Guide 4 RF/IR Remote Control & batteries 4 Component Video cables (YPbPr) 4 RF Remote Antenna 4 B-Band Converter 3 About High-Definition What is HD, and how does it differ from regular TV? To learn more, here's some helpful information about high-definition and your DIRECTV HD Receiver. Types of TV Broadcasts Analog TV is the type of TV broadcast you may be most familiar with. If you get your broadcasts via a standard off-air antenna, it's the type you receive, and most broadcasts from local cable companies are analog as well. Digital TV is a newer system for broadcasting TV signals delivering higher quality audio and video. "Digital TV" refers to a television that can receive and display digital images. Following are terms you might see used regarding Digital TV broadcasts. Although your DIRECTV HD Receiver is a "true" HD receiver, the type of TV or monitor you plug it into (SD, ED, or HD) can affect the resolution of the TV picture you see. See "Resolutions and Interlacing" on page 6, for an explanation of display resolutions. 4 SD (standard definition) is digital TV that offers a picture quality that is better than older analog televisions. SDTV displays images at a resolution of 480i. 4 ED (enhanced definition) is digital TV that can display a higher resolution picture than SDTV. An EDTV can display at 480i or 480p. To get the best-quality TV picture, you need an HD TV to go with your DIRECTV HD Receiver. 4 4 HD (high definition) is digital TV that can provide the highest quality picture, at resolutions 1080i, 720p, 480p, or 480i. Equipment You'll Need To view HD programming, you'll need, in addition to your DIRECTV HD Receiver: 4 A high-definition TV set (or HDTV monitor) 4 A 5 LNB Multi-Satellite dish antenna--MPEG4 and Ka/Ku compatible To enjoy select HD programming available on off-air local channels, you will also need an off-air antenna (sold separately) connected to your DIRECTV HD Receiver. This is possible only in cities where local broadcast stations make digital TV programs, including high-definition, available. Reception may vary based on your geographic location. With an optional off-air antenna, you can also watch locally broadcast HD channels. What You Can Watch With the DIRECTV HD Receiver, you have access to all types of televised programming, including: 4 DIRECTV high-definition and standard-definition digital programming via satellite, including network channels if offered in your area (DIRECTV service subscription required). 4 Local digital TV channels, including any local HD broadcasts shown in your area, available via an offair antenna. 5 Resolution & Interlacing Two elements that determine the quality of a TV picture are: Resolution If you've ever looked very closely at your TV, you have noticed the picture is actually made up of many lines scanning across the screen. The set of lines that make up a complete image are called a "frame." For TV equipment and broadcasts, resolution is defined by the number of horizontal lines displayed to make up each frame of a video image. The more lines of resolution used to compose each frame, the more detailed and sharp the picture. Standard TV resolution uses 480 horizontal lines to make up each video frame; HDTV uses either 720 or 1080 lines to compose each frame. Interlaced & Progressive The term "interlacing" refers to whether each of those frames contains all of the lines of image, or every other line. Interlaced signals take every other line from 2 frames, each lasting 1/60th of a second, and combine them into one frame lasting 1/30th of a second. In this way, interlacing tricks the eye into thinking it's seeing twice the resolution that's actually being displayed. In non-interlaced video, referred to as "progressive scan" video, frames are displayed every 1/60th of a second containing all of the lines of video information. The specifications for video resolution are usually stated by giving the number of horizontal lines (480, 720 or 1080, as described above) followed by either the letter "i" (for interlaced) or "p" (for progressive scan). Most standard TV broadcasts are 480i; some DVDs and non-HDTV digital broadcasts use If your DIRECTV was professionally installed, you can skip this section. 6 480p. Specification for HDTV broadcasts and equipment requires either 1080i or 720p. Aspect Ratio In addition to resolution and interlacing, a television picture is also defined by its aspect ratio--referring to the shape of the screen as defined by the ratio of the screen's width to its height. For analog TV, the aspect ratio is 4 units wide by 3 units high (4:3). This is the familiar shape of conventional TVs--slightly wider than they are tall. SDTV and EDTV can be either 4:3 or 16:9. For HDTV broadcasts, the aspect ratio is 16:9--nearly twice as wide as it is tall. This is, not coincidentally, more like the shape of movies shown in theaters, which makes HD an ideal format for viewing movies on TV. You will be able to see much of what is captured on fi lm, but lost on an SDTV display. Screen Formats Honey, does this receiver make my screen look wide? What if you're watching a nearly square-shaped 4:3 broadcast on a 16:9 TV, or vice versa? The DIRECTV HD Receiver lets you choose from a variety of screen formats to deal with those scenarios. You can set up your preferences for format during Guided Setup and change them at any time. See the next page for your options. 7 Wide-Screen vs. Standard Formats 4:3 TVs Showing 16:9 programs For a standard 4:3 TV showing a wide screen program, the program is too wide to fit on the screen. To alleviate this, choose: Letterbox With this format, the 16:9 image is shrunk until the entire width of the program fits on your TV. Since the aspect ratio of the program is maintained, the image is no longer tall enough to fi ll your screen, so gray or black bars are seen at the top and bottom of the screen. To change the bar color, press MENU, then select Settings. Select Setup, then select the Display menu. Highlight the Preferences tab and press SELECT, then set Bar Color option to the desired color. See your TV owner manual for information on the best color for your set. Stretch In the Stretch setting, instead of adding bars to the top and bottom, the 16:9 program image is stretched vertically until it's tall enough to fi ll the screen. Your entire screen will be full, but the program images are stretched to compensate. Crop This format crops (cuts off ) the left and right portions of the 16:9 frame so it fits the 4:3 screen. You can watch HD programs on a standard TV, but you won't really be watching HD. 8 If your display is a 4:3 format TV or monitor, your format options include these: For 4:3 program signals: Fills TV Screen Only Letterbox shows the entire original 16:9 image without distortion. For 16:9 program signals: Letterbox Stretch Crop 9 16:9 TVs Showing 4:3 programs For a wide screen 16:9 TV showing a standard 4:3 TV program, the program is too tall to fit the screen. Your choices here include: Pillar box Here the 4:3 image is shrunk until the entire height of the program fits on your TV. Since the aspect ratio is maintained, the image is no longer wide enough to fi ll the screen, so gray or black bars are seen at the left and right edges. To change the bar color, access the HDTV screen in System Setup as described above, then select the desired bar color option under the TV Ratio tab. Stretch In this setting, instead of adding bars to the sides, the 4:3 program image is stretched horizontally until it's wide enough to fi ll the screen. Your entire screen will be full, but the images are a little stretched to compensate. Crop This format crops (cuts off ) the top and bottom of a 4:3 frame, keeping the 4:3 ratio intact. Fortunately, you can still watch regular TV on your HD TV. Isn't it nice to be one step ahead of the rest of the world? 10 If your display is a 16:9 format TV or monitor, your format options include these: For 4:3 program signals: Pillar Box Stretch Crop For 16:9 program signals: Fills TV Screen Only Pillar Box shows the entire original 4:3 image without distortion. 11 " If you think the hardware is awesome, just wait until you see what comes out of it! Hardware Reference General Satellite Dish Antenna This is your "dish" and related hardware, affi xed to your roof or other surface, which picks up the broadcast signals from our satellites. DIRECTV HD Receiver (or Satellite Receiver) Your DIRECTV Receiver picks up the signal from your satellite dish antenna and translates it into viewable TV programming. Access Card Contains information about your DIRECTV service. It must be properly inserted for your receiver to work and to activate your programming. Off-Air Digital Antenna (not included) This antenna attaches to the back of your DIRECTV HD Receiver and is used to receive local "off-air" digital broadcasts. 13 Cables & Connections HDMI Jack and Cable The DIRECTV HD Receiver incorporates HDMITM [or High-Definition Multimedia Interface] technology. HDMI offers a high-quality connection that combines the video and audio signal into a single cable. The HDMI jack uses HDCP content protection to allow you to view HD programming that has been encoded using the HDCP protection system. For the best access to HD programming at the highest available resolution, connect this to an HDTV that supports HDCP technology. DVI (Digital Visual Interface) is an older digital connection standard that has been replaced by HDMI and is compatible with HDMI. DVI carries video only. You can also use an HDMI to DVI converter (not included), which also carries video only, so must be used with audio cables to receive the audio signal. Component Video Output ( YPbPr) The component connector provides high-quality video for your HDTV system. Component video is also referred to as "YPbPr." It uses three separate cables--with connectors colored green, red and blue--one for each component of the HD video signal. Y Pr Pb Note: You may need to purchase additional cables depending on your setup. HDMI and optical cables not included. Note 14 HDMI and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Digital Audio Outputs (Optical Jack and Cable) The Digital Audio Optical cable provides the best quality audio. The jack and cable use light to send digital audio data to A/V receivers equipped to receive and interpret it. The jack and cable (cable not included) must be aligned before plugging in, and may be covered by protective caps, which must be removed before making connections. Use caution when handling optical cables: They are delicate! S-Video Jack and Cable S-Video jacks and cables provide the best non-HD picture quality. You will still need to connect the left and right audio cables to the TV, or optical audio cable to your stereo, because the S-Video cable only S-Video Jack carries the picture signal, not sound. Audio/Video (A/V) Jack and Cable Audio/Video (A/V) cables provide very good picture quality and stereo sound, and should be used if you don't have HDMI, component or S-Video cables, or your TV does not have HDMI, component or S-Video jacks. The DIRECTV Receiver's A/V jacks are color coded (yellow for video, red for right audio and white for left audio). If your TV has only one input for audio (mono), connect it to the left (white) R L Video audio jack on the DIRECTV Receiver. Telephone Jack and Cord The telephone line cord connects your DIRECTV Receiver to a land-based telephone line. The phone line connection is used to periodically call DIRECTV. This connection is required for sports package subscriptions and for purchasing PPV movies and events. You will need an RJ11-type modulator jack (the most common type of phone jack). Note: Do not connect your receiver to a digital PBX phone system -- doing so may permanently damage your equipment and void your warranty. Phone Jack 15 " This is the part where you might want to invite your favorite gearhead over for pizza. If you are your favorite gearhead, pat yourself on the back. ELECT Acti ve In fo Locate the access card that came with your DIRECTV HD Receiver. Write down the card number in the space below, then insert the card into the receiver, facing upward, fully into the slot. Card # Your equipment may not look exactly like the model illustrated. DIRECTV HD Receiver Front Panel 1) 2) 3) 4) POWER ­ Turns your DIRECTV HD Receiver on or off. Your Receiver still tunes and receives messages when powered off. REMOTE SENSOR ­ The infrared sensor picks up commands from the remote control. GUIDE ­ Displays the onscreen program guide. RESOLUTION/RESOLUTION INDICATOR ­ The RESOLUTION key switches the output resolution of the HD receiver. Each time you press the key, it cycles to the next available resolution: 1080i, 720p, 480i and 480p. The adjacent lights indicate the current resolution setting. MENU ­ Brings up the Quick Menu to access settings and services. ARROWS ­ Move the onscreen highlight up, down, left or right. SELECT ­ Selects the item highlighted. ACTIVE ­ For future use. INFO ­ Displays channel banner or info to a highlighted program or channel cell. DOOR PANEL ­ The access card slot and RESET button are located behind the door panel. 5) 6) 7) 8) 9) 10) 17 6 OFF AIR IN COMPONENT OUT RF REMOTE ANTENNA DIGITAL AUDIO OUT (OPTICAL) HDMI VIDEO OUT AUDIO OUT SATELLITE IN S-VIDEO OUT USB AC IN PHONE JACK 1 7 2 3 4 5 7 8 9 10 11 12 Your equipment may not look exactly like the model illustrated. DIRECTV HD Receiver Rear Panel 1) 3) OFF-AIR IN ­ Used to receive local, off-air digital broadcast channels. USB ­ For future services and accessories. Additional hardware may be required. If your TV has only RCA and S-Video jacks, use it along with the audio jacks (S-Video only carries picture information, not sound) to connect to your TV. 5) VIDEO OUT ­ Provides good, but non-HD, picture quality. You can connect the second RCAtype composite VIDEO jack to another device, such as a VCR. You must also connect the AUDIO 2) SATELLITE IN ­ Use to connect the DIRECTV HD Receiver to the satellite dish antenna. 4) S-VIDEO OUT ­ Provides the best non-HD picture quality, better than VIDEO RCA-type jacks. The Rear Panel may look complicated, but you probably won't use all the connections. 18 cables when using the VIDEO connection. 6) COMPONENT OUT/ YPbPr (G, R, B) ­ Provides good HD picture quality, but not as good as HDMI. YPbPr carries only picture information, not sound; use it along with a digital audio connection or Audio Out (L/R red/white) jacks. 7) AUDIO OUT (R and L) ­ Connect a second set of audio cables to another component, such as a VCR or stereo. 8) DIGITAL AUDIO OUT (OPTICAL) ­ Provides digital-quality audio signal. (Cable sold separately.) 9) HDMI ­ Provides the best quality HD picture (better than YPbPr/component video). The HDMI also provides audio, for a high-quality, "one-cable" solution. (Cable sold separately.) 10) RF REMOTE ANTENNA ­ Used to receive the signal from your remote when it's being used as an RF remote. 11) PHONE JACK ­ Connects the DIRECTV HD Receiver to a telephone line. The DIRECTV HD Receiver requires a land-based telephone line connection to communicate periodically with your program provider. 12) POWER ­ Use to connect the power cord for your DIRECTV HD Receiver. Connect video, audio, your satellite dish, a phone line, power, and you're done! 19 Choose Your Setup There are several ways to connect your receiver to match your particular equipment setup and to gain optimum signal quality. The basic steps are as follows: · Connect the satellite dish cable to your receiver. · Connect the receiver audio and video to your TV or VCR. · If you connected the receiver to a VCR, connect the VCR to your TV. · Connect the receiver to a telephone line. · Plug in all power cords. This section gives detailed instructions on the types of connections you can make, depending on the equipment you have, in order to get the best picture and sound quality. Note that the back panels of your TV and other equipment may not exactly match those illustrated. OUT IN All A/V jacks and inputs are color coded. Always match the color of the plug to the same color of the jack. TIP When working with cables, be sure to connect corresponding outputs and inputs (Video OUT to Video IN, Right Audio OUT to Right Audio IN, etc.). Never connect an IN to an IN or an OUT to an OUT. 20 Connecting Your DIRECTV HD Receiver to your TV or VCR Depending on the inputs on the back of your TV or VCR, you have the following options for connecting your DIRECTV HD Receiver: · HDMI Everybody wants to be connected. · YPbPr Video · S-Video · Digital Audio (optical) · Analog Audio These connections are described on the following pages. Important Due to restrictions imposed by copyright holders, certain programming may include content protection meaasures that may restrict viewing in high-definition and/or recording with certain consumer electronics equipment attached to the receiver. Please contact the manufacturer of such equipment for additional information. 21 Making the Video Connections Choose one of the following connections: · Best (HD Video and Digital Audio): Connect the HDMI cables to the HDMI jacks on the receiver and your TV. HDMI cables also carry digital audio, so you do not need to make a separate audio connection, unless you would like to use other audio outputs; for example, if you want to connect your DIRECTV HD Receiver to a stereo or home theater system. Note: HDMI cable is not included with the HD Receiver. · Better (HD Video): Connect one end of the Component (Y Pb Pr) video cables to the COMPONENT OUT video jacks on the DIRECTV HD Receiver. Connect the other end of the component video cable to the component input on your TV, making sure to correctly match the red, green and blue connectors. You will need to connect audio separately. · Good (Non-HD): Connect one end of the S-Video cables to the S-VIDEO OUT jacks on the DIRECTV HD Receiver. Connect the other end to the S-Video input on your TV. Note: The SVideo cable will not provide an HD signal to your TV. · Not recommended (Non-HD). You can use RCA connectors to connect your DIRECTV HD Receiver to your TV, but it is not recommended. To get the best quality of image, use one of the above methods. However, if your TV does not support S-Video, component or HDMI connections, connect one end of the RCA cable (usually with a yellow plug) to the VIDEO OUT jack on the DIRECTV HD Receiver. Connect the other end to the video input on your TV. TIP To switch between watching your VCR and watching video from your receiver, you may need to program the INPUT key on your DIRECTV Remote. (See page 30 for info.) Some TVs also have a MENU button that allows you to change the video source using an onscreen menu. If you have trouble changing the video source, refer to the instructions that came with your TV. Important 22 To obtain optimum picture quality, make sure the receiver is connected directly to the TV. Connecting the receiver to the TV through a VCR or DVD recorder is known to yield less than optimum picture quality, particularly when viewing copyprotected programming. Connect Video Cables ­ Television The back panels of your equipment may not look exactly like those illustrated. S-VIDEO IN COMPONENT IN DIGITAL AUDIO IN (COAXIAL) DIGITAL AUDIO IN (OPTICAL) HDMI S-VIDEO HDMI (includes video & audio) GO OD BE TT ER * S-VIDEO DIRECTV® HD Receiver BE ST HDMI SATELLITE IN *Note: Do not confuse the component YPbPr cable with a standard Audio/Video (RCA-type) cable. Observe the Red, Green, Blue color-coding. You will not get HD video if you use the Video Out connector on your DIRECTV HD Receiver or TV. 23 Making the Audio Connections · Best: If you connected your DIRECTV HD Receiver to your TV with HDMI cables you do not need to make a separate audio connection, unless you would like to use other audio outputs; for example, if you want to connect your DIRECTV HD Receiver to a stereo or home theater system. Note: HDMI cable is not included with the DIRECTV HD Receiver. · Best 2: You may also receive digtal audio by connecting an Optical Audio cable from the DIGITAL AUDIO OUT (OPTICAL) jack on your DIRECTV HD Receiver to a DIGITAL AUDIO IN (OPTICAL) jack on your TV. This output can also be used if you wish to listen to audio on a stereo or home theater system, even if you are already using an HDMI cable for audio on your TV. Note: Optical Audio cable is not included with the DIRECTV HD Receiver. · Good: For analog audio, connect the white (L) and red (R) RCA-type cables from the DIRECTV HD Receiver to your TV. If you used an HDMI cable to hook up video, you can skip this section. Note 24 If your TV only has one audio input jack use AUDIO L (white) jack on the back of the DIRECTV Receiver to make the connection. Connect Audio Cables ­ The back panels of your equipment may not look exactly like those illustrated. Television S-VIDEO IN COMPONENT IN DIGITAL AUDIO IN (OPTICAL) HDMI RCA-type DIGITAL OPTICAL GO OD DIRECTV® HD Receiver BE ST 2* SATELLITE IN * NOTE: For best audio quality, use the HDMI cable for audio and video. (See "Making the Video Connections.") 25 Making the Basic Connections 1) Connect DIRECTV HD Receiver to Satellite Dish. Connect the RG-6 RF coaxial cable from your satellite dish to the jack labeled SATELLITE IN on the DIRECTV Receiver. 2) Connect Off-air antenna to DIRECTV HD Receiver (optional). Connect the off-air antenna to the jack labeled OFF-AIR IN on your receiver. When you go through the Guided Setup process, be sure to select the Satellite & Antenna button when you reach the Satellite Dish & Off-Air Antenna screen. 3) Connect RF remote antenna to DIRECTV HD Receiver (optional). If you want to use your remote without having to point it at the receiver, such as from another room, or in a setup where objects are likely to block the beam from your remote to your DIRECTV HD Receiver (such as the receiver is in a cabinet with a door), then plug the RF remote antenna into the RF REMOTE ANTENNA jack on your receiver. Your receiver defaults to IR functionality. You can activate RF functionality during Guided Setup. After Guided Setup, you can activate RF functionality by going to the System Setup screen and choosing REMOTE in the left menu. Select IR/RF Setup button and follow the on screen instructions. 4) Connect DIRECTV HD Receiver to Telephone Line. Plug one end of the telephone cord into a phone jack on your wall (or into a phone splitter that is plugged into a phone jack) and the other end into the PHONE JACK on the back of the DIRECTV Receiver. 5) Plug all power cords into electrical sockets. You're almost done! 26 Connect Other Cables ­ The back panels of your equipment may not look exactly like those illustrated. While you're looking at the back of your DIRECTV HD Receiver, write down the serial number, receiver ID and model number. You'll need them later. Serial # 1 DIRECTV® HD Receiver OFF AIR IN SATELLITE IN 2 3 4 5 Receiver ID Model # (Copy these numbers to page 82 along with your other purchase information) 27 Guided Setup & Activation Now that your receiver and equipment are all hooked up and plugged in, you're ready to complete setup to begin enjoying your DIRECTV service. 1) Make sure the MODE switch at the top of the remote control is set to DIRECTV, which is the farleft position. 2) Press TV POWER ON. The DIRECTV Receiver will turn on. 3) The first screen will allow you to select a language. Using the arrow keys on the remote control, move to the language you prefer and press SELECT. 4) You will see a Welcome screen. TV INPUT AV1 AV2 TV TV POWER ON PWR TIP You may decide to set up, change or adjust some of the settings later. When you're ready, press MENU on your remote, press SELECT on Settings then select Setup. SELECT MENU 28 HDTV settings in Guided Setup Several screens in the Guided Setup process are related to HDTV: 4 TV Ratio Screen: This screen lets you select your TV's aspet ratio: 4:3 or 16:9. 4 TV Resolutions Screen: As you select each resolution, an onscreen message asks if you can still see the screen properly. If you can, press the INFO key. If not, the unsupported resolution is turned off after a few seconds. If you turn on Native mode, the receiver will automatically adjust resolution to match the resolution of individual TV programs as they are tuned. 4 Primary Local Network: If you've chosen to set up both your Satellite Dish and Off-Air Antenna, you will see this screen near the end of Guided Setup. The receiver will use the ZIP code you enter on this screen to determine what locally broadcast digital stations are available to you. Setting up a Secondary Local Network is optional; it can be useful if you are located between two network areas and intend to receive programming from both via your off-air antenna. The User Guide that came with your TV will help you set the HDTV settings properly. 29 Now, let us lead the way... Simply follow the onscreen directions to complete your setup functions. If you've installed your satellite dish and system yourself, you'll be guided though various functions for optimizing your signal and setup -- including positioning your dish and a system test. If you had your system professionally installed, these functions already have been completed. After these setup procedures are complete, you'll see a message onscreen that says, "Acquiring Satellite Info," as the receiver gathers information from the satellite for the onscreen program guide. Next, you'll be given the opportunity to program your remote to control other equipment such as your TV and/or DVD player. Just follow the screen instructions and you'll be ready to watch in no time! Guided Setup is as simple as following the onscreen instructions. When in doubt, we've usually highlighted the most likely choice for you. Important In order to protect your TV screen from burn-in (a side-effect caused when a stationary image is displayed for too long), the DIRECTV Receiver interface automatically goes into screen saver mode, and displays a black screen with a moving logo when no key is pressed for 5 minutes or more while a stationary image is displayed on the TV. To dismiss the screen saver and return to what you were doing, press any key on the remote. Burn-in may cause permanent damage to your TV and DIRECTV is not liable for any damages that may be caused to your TV. 30 Activate Your DIRECTV Service Once all the setup processes are complete, all that's left to do is activate your DIRECTV service. Before you make the call, be sure to: 4 Have on hand your service address, social security number and a valid major credit card. 4 Note your access card and receiver ID numbers. (You may have written them down earlier in this chapter.) When you're ready, just call 1-800-DIRECTV (1-800-347-3288) and pick the programming package that's right for you. 31 " Hang in there... Just a little more techie stuff to go. Programming Your Remote Control You may have already programmed your remote control during Guided Setup, but if you didn't, or you want to make changes, or you've acquired some new equipment, follow these instructions. If you programmed your Remote Control during Guided Setup, you can skip this section. You can program the DIRECTV Remote Control to operate your TV power, volume and mute, additional equipment such as a DVD, VCR, stereo, or second TV or DIRECTV Receiver. 1) 3) Press MENU to display the Quick Menu. Highlight Setup and press SELECT. 2) Highlight Settings and press SELECT. 4) Press SELECT on Remote in the left menu. 5) Follow the onscreen instructions to program your remote for your TV or additional equipment (AV1 and AV2). Once your remote is programmed to work with your TV, the VOL and MUTE key control the TV regardless of the slide switch position. If you would like to change the VOL and MUTE to work with other audio equipment, such as a stereo, you can. When you program the remote for the audio equipment, onscreen instructions will direct you on how to do this. 33 Options For Changing Video Output In order to optimize the display of programs on your television, you may occasionally need to change the resolution and/or screen format. There are two keys that can be used to make changes: the FORMAT key on the remote control and the RESOLUTION key on the front panel of the receiver. FORMAT key on Your Remote Pressing this key will cycle the resolutions that you've indicated in System Setup as being supported by your TV. In addition, it will cycle the three available screen formats in conjunction with each individual resolution. Available screen formats are based on the TV Aspect Ratio you set in System Setup. With each press, an onscreen message will let you know what the current resolution/format setting is. For example, if you indicated that your TV supports only 1080i, 480i and 480p and it is a 16:9 television, and Native is turned off *, the cycle of settings for the FORMAT key are as follows: 1st press: 480i/Stretch 2nd press: 480i/Letter box 3rd press: 480i/Crop 4th press: 480p/Stretch 5th press: 480p/Letter box 6th press: 480p/Crop 7th press: 1080i/Stretch 8th press: 1080i/Letter box 9th press: 1080i/Crop 10th press: repeat cycle The FORMAT key, made simple: Keep pressing the FORMAT key until you like the picture on your TV. * 34 In Native mode, the receiver automatically adjusts resolution to match the resolution of individual TV programs as they are tuned. If your TV supports all formats (1080i, 720p, 480i and 480p), then your cycle would also include 720p. If Native is turned on, the FORMAT key cycles through Stretch, Letter and Crop for the current TV program's native resolution. The FORMAT key allows you to easily cycle all resolution and format settings with a single key until the picture displays the way you like it. Navigating menus to modify settings is not necessary. If pressing this key causes a loss of video and audio, continue to press it until the picture returns. (Wait a second between presses to allow the Receiver to change the resolution.) Th is can happen if your settings include a resolution that your TV doesn't support. To correct this, you'll need to change your resolution setting: Press MENU, select Settings, then Setup, then HDTV in the left side menu. Press SELECT on the Resolution tab and mark or unmark the TV Resolutions to display the resolutions supported by your television. Resolution made simple: Set the resolution to the highest number that your TV supports by pressing the RESOLUTION key. RESOLUTION Key on Receiver Front Panel This key is used to cycle all available resolutions on your DIRECTV HD Receiver. It does not cycle format settings. If video and audio are not appearing, it may be because the current resolution setting is not supported by your television. By pressing this key, you can check all available resolutions to see if that solves the problem. The lights next to the RESOLUTION key on the front panel will light below the resolution to which the receiver is set; they will change with each key press. 35 Using Your IR/RF Remote to Control Your DIRECTV HD Receiver You can skip this section if you setup your Remote Control during Guided Setup. It is included here if you skipped that part, or if you want to change your Remote setup later. The remote control included with your DIRECTV HD Receiver works in either IR (infrared) or RF (radio frequency). IR is the "typical" type of remote you are already familiar with from other remotes you may have -- the remote must be pointed at the device for it to respond. RF allows you to operate the DIRECTV HD Receiver without having to point your remote directly at it, such as when the receiver is installed in a cabinet, or you use the remote from another room in your house. The operating range of the remote is up to 200 feet, with some possible decrease due to weak batteries or obstacles such as walls in your house. Once programmed, your RF will be addressed to only one receiver, so will not affect other receivers in your home. To setup your remote for RF, press the MENU key, press SELECT on Settings, then select Remote from the left menu. Press SELECT on the IR/RF Setup button. Follow the onscreen instructions to configure your remote. A remote that can go through walls? That's right: We're rethinking your remote, too. 36 Receiving Local "Off-Air" Broadcast Channels The DIRECTV HD Receiver can receive both satellite and locally transmitted, off-air broadcast channels, and will display these local channels in the Guide. In order to receive off-air channels, attach an off-air antenna to the OFF-AIR IN as instructed in the "Choose Your Setup" section starting on page 20. During the Guided Setup process, be sure to select the Satellite & Antenna button when you reach the Satellite Dish & Off-Air Antenna screen and follow the onscreen instructions. If you didn't setup an off-air antenna during the guided setup, you must enter your location into the NOTE: Your reception sill vary by geographic location. In other words: Some areas get better reception than others! receiver using the Local Network Area screens in order to receive Program Guide information for local off-air broadcast channels. When you enter your ZIP code, if there is more than one network area available, your receiver will show your options. Pick the one closest to you as your primary network area. In some cases, there may be more than two cities displayed. You may decide to also enter a secondary local network if more than one is available to you, but this is optional. To scan for off-air channels and set up the local network areas after Guided Setup, do the following: 1. 2. 3. 4. 5. 6. Press MENU. Press SELECT on Settings in the Quick Menu. Select Setup in the Quick Menu. Select Sat & Ant from the options on the left menu. Press SELECT on the Antenna Setup button. If you have not selected your local networks yet, select the Local Networks button and follow the instructions until you are done. Select the Scan for Channels button to have the receiver scan local off-air frequencies. When the receiver has finished scanning for channels, you are given the chance to edit local off-air channels to remove channels from the Guide that you don't watch, or those that have poor reception. 37 " Now let's watch some TV! 41 Watching TV Chapter 2 45 The Guide 47 Autotune 49 Pay Per View What's On 39 TIP Use the Channel Lineup (included in your Welcome package) to get familiar with our channel numbers. Watching TV Now that everything's set up, you're ready to grab your remote and start surfing! With the MODE switch to the left (under the DIRECTV logo), press PWR. To access the channel of your choice, simply key in its numbers on your remote (the channel will appear in a second or two, or press ENTER after the numbers and it will appear right away). You can also navigate to different channels through the Guide, described in detail later in this chapter. Keep in mind, either way, you'll only be able to access those channels in your chosen DIRECTV® programming package. For a list of the channels available in the DIRECTV programming packages, visit DIRECTV.com. Use the black keys on the left side of your remote control to adjust volume up or down (VOL) or mute VOL CHAN the sound (MUTE). The black keys on the right side can take you to the next channel numerically up or down (CHAN), or jump to the previous channel you watched (PREV). MUTE PREV PAGE 41 1 2 3 4 5 6 7