Detailed instructions for use are in the User's Guide.
DIRECTV® Universal Remote Control User's Guide
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features And Functions . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DIRECTV DVR and UltimateTV Key Charts. . . . . . . . . . 7
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 8 About DIRECTV Control . . . . . . . . . . . . . . . . . . . . . . 9
Programming DIRECTV Control. . . . . . . . . . . . . . . . . . 9 Setup Codes for DIRECTV® Receivers. . . . . . . . . . . . 10 Setup Codes for DIRECTV DVRs . . . . . . . . . . . . . . . . 11
Programming Other Device Control. . . . . . . . . . . 11 Programming TV/VCR Combo Control . . . . . . . . 12 Manufacturer's Codes. . . . . . . . . . . . . . . . . . . 14
Setup Codes for TVs. . . . . . . . . . . . . . . . . . . . . . . . . 14 Setup Codes for VCRs . . . . . . . . . . . . . . . . . . . . . . . 17 Setup Codes for TV/VCR Combos . . . . . . . . . . . . . . . 19 Setup Codes for Digital Video Recorders (DVRs) . . . . . 20 Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . 20 Setup Codes for Stereo Receivers . . . . . . . . . . . . . . . 21 Setup Codes for Stereo Amplifiers . . . . . . . . . . . . . . 22
Searching For Your Code . . . . . . . . . . . . . . . . . . . . 23 Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . 24 Using The Master Power Key. . . . . . . . . . . . . . . . . 25 Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . 26 Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . 27
To Change Volume Lock to the VCR Mode . . . . . . . . . 27 To Change Volume Lock to the SAT Mode . . . . . . . . . 27 To Change Volume Lock to the AUX Mode . . . . . . . . . 27 To Change Volume Lock Back to the TV Mode . . . . . . 28
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Repair Or Replacement Policy . . . . . . . . . . . . . . . 30 Additional Information . . . . . . . . . . . . . . . . . . . . . . 31
2
INTRODUCTION
Congratulations! You now have an exclusive DIRECTV® Universal Remote Control that will control four devices, including a DIRECTV Receiver, TV,VCR, and an auxiliary device. Moreover, its sophisticated technology allows you to consolidate the clutter of your original remote controls into one easy-to-use unit that's packed with features such as: · Preprogrammed interactive technology that links hot keys to your DIRECTV® service · Master Power key for master on/off control of all of your equipment with a single keystroke (when Power is held for 3 seconds) · Macro keys for sorting movie and sports programs in the DIRECTV® programming (on most DIRECTV Receivers) · ID Lock to lock your remote control for use only with a selected DIRECTV Receiver · Automatic back lighting of most commonly-used keys that become active with any key press · Code library for popular video and audio devices · Code Search to help program control of older or discontinued devices Before using your DIRECTV Universal Remote Control, you may need to program it to operate with your particular home entertainment devices. Please follow the instructions detailed in this User's Guide to setup your DIRECTV Universal Remote Control so you may start enjoying its features.
3
FEATURES AND FUNCTIONS
Use the illustration below to locate feature keys on the DIRECTV Universal Remote Control. The Key Charts on the next three pages explain their functions.
4
Key Charts
Press TV, AUX, VCR, or SAT once to select a home entertainment device to control. Each key has a red indicator light that blinks upon selection and indicates the device currently being controlled by your DIRECTV® Universal Remote Control. Press Power once to turn on or off a home entertainment device. Press and hold Master Power for 3 seconds to turn on or off all home entertainment devices (see Using The Master Power Key on page 25). Use Input/ANT to select available inputs on the TV. For VCR or DVD use, select Input/ANT to view the TV or video. Use Volume to raise (or lower) the sound volume. Press Mute once to turn the sound off or on. Use Info to display the current channel and program information. Press Menu/DIRECTV once to display the main menu. Use Guide to display the DIRECTV program guide. While watching TV, use CH L (or M) to select the next higher (or lower) channel. While in the DIRECTV program guide, use Page L (or M) to page up (or down) through available channels in the program guide. Use the cursor keys to move the cursor in the program guide and menu screens.
continued on next page..
5
FEATURES AND FUNCTIONS
Key Charts (continued)
Use Select/OK to choose highlighted items in the menu screens and in the program guide. Use Exit (Clear) to exit menu screens and the program guide. Use (DIRECTV INTERACTIVETM) to access interactive features (if available on your DIRECTV Receiver). Use Favorite to view favorite channels that have been programmed. Use Movies to sort the guide to show programs that are movies (on most DIRECTV® Receivers). Use Sports to sort the guide for available sports-related programs (on most DIRECTV Receivers). Use the keypad (0 ~ 9) to directly tune a channel (e.g., 206).
Press Prev CH once to return to the the last channel viewed. Press Back once to page back one page in the menu. Press Alt Audio once to switch between English and a foreign language (e.g.,Spanish) if alternate audio is avaialble. Press Enter once to tune to a channel on some TVs. Use the transport keys to control your VCR, DVR, or CD/DVD player. To record a program, press Record twice. Use (Â) to separate main and sub-channel numbers (e.g., 2-1). Press and hold Setup for 3 seconds for all programming sequences. 6
DIRECTV® DVR and UltimateTV Key Charts
NOTE: On DIRECTV DVRs and DIRECTV Receivers with Tivo or UltimateTV service, several remote control keys function differently than those listed in the previous section. They are described below:
For DIRECTV DVRs, press to display program options (DIRECTV Central). For DIRECTV Receivers with UltimateTV, press to display the shows you have recently recorded (Recent). For DIRECTV DVRs, use Favorite to switch from watching a recorded show to live TV (Return To Live). For DIRECTV Receivers with UltimateTV, use Favorite to view a list of shows you have recorded (My Shows). Use Info to display the current channel and program information. Press Info while in the program guide to display additional guide options. Press Movies for "Thumbs Down." (Available only on DIRECTV DVRs). Press Sports for "Thumbs Up." (Available only on DIRECTV DVRs). Use these transport keys to control the digital video recorder (DVR) built into your DIRECTV DVR or DIRECTV Receiver with Ultimate TV. Use (Â) to separate main and sub-channel numbers (e.g., 2-1). Use Skip Back to replay a program recorded by your digital video recorder. Use Skip Fwd to advance a program a program recorded by your digital video recorder.
7
INSTALLING BATTERIES
The DIRECTV® Universal Remote Control comes with preinstalled batteries.To activate them,pull the tab out of the battery case. To change the batteries, perform the following steps:
NOTE: The DIRECTV Universal Remote Control will stop operating when the batteries are fully drained. Replacing the batteries will restore your DIRECTV Universal Remote Control to its full functionality, complete with your favorite settings.
1.
On the back of the remote control, push the latch (as shown), lift off the battery cover, and remove the used batteries. Obtain two (2) new AA alkaline batteries. Match their + and  marks to + and  marks in the battery case, then insert them. Align the cover's tabs with the case's holes. Press down on the cover until the latch locks. Test the remote control by pressing Power and any device key (e.g.TV,VCR,AUX,or SAT).If the batteries are inserted correctly,the selected device key will blink once. 8
2.
3. 4.
ABOUT DIRECTV CONTROL
The DIRECTV® Universal Remote Control is designed to give you access to features not found on the original remote control.It is preprogrammed at the factory to operate a HNS-manufactured DIRECTV Receiver, so you can skip this section if you have this brand. However,to use it with other brands of DIRECTV Receivers,you will need to program the remote control by performing the following steps:
Programming DIRECTV Control
1. Locate the DIRECTV Receiver's brand and model number (on the back or bottom panel) and write it in the spaces below. Brand __________________________ Model # _________________________
NOTE: Please read steps 2-5 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
2. 3.
Power on the DIRECTV Receiver. On the DIRECTV Universal Remote Control, press SAT once. Press and hold Setup until the SAT key blinks twice,then release Setup. Use the Setup Codes for DIRECTV Receivers or DVRs (on the next two pages) to locate the brand name and code for your specific DIRECTV receiver. Then use the keypad to enter the four-digit code. If performed correctly, the SAT key will blink twice.
NOTE: If the SAT key emits a long blink, the code is invalid. Repeat steps 3 and 4 and try entering the same code again.
4.
5.
Aim the DIRECTV Universal Remote Control at the DIRECTV Receiver and press Power once. The DIRECTV Receiver should turn off. If it does not, repeat steps 3 and 4, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code on page 23. For future reference, write down the working satellite receiver code in the following box: SAT Code:
continued on next page...
6.
9
ABOUT DIRECTV CONTROL (continued)
Setup Codes for DIRECTV Receivers:
Hughes Network Systems (most models) Hughes Network Systems models GAEB0, GAEB0A, GCEB0, GCEB0A, HBH-SA, and HAH-SA GE models GRD33G2A and GRD33G3A GE model GRD122GW Hitachi model HDS210R Mitsubishi HD models SRHD400 and SRHD500 Panansonic models TZ-DBS01 and TZ-DRD100 Panasonic models TUIRD10 and TUIRD20 Philips models DSX5150R, DSX5250R/I, DSX5350R, DSX5353R, DSX5353X, and DSX5375R Philips models DSX5500 and DSX5400 Philips HD model DSHD800R Proscan model PRD8630A Proscan model PRD8650B RCA models DRD102RW and DRD203RW RCA models DRD301RA, DRD302RA, DRD303RA, DRD403RA, and DRD703RA RCA models DRD502RB, DRD503RB, DRD505RB, DRD515RB, DRD523RB, and DRD705RB RCA models DRD202RD, DRD221RD, DRD222RD, DRD223RD, DRD225RD, DRD420RE, DRD440RE, DRD460RE, DRD480RE, DRD430RG, DRD431RG, DRD450RG, DRD451RG, DRD485RG, DRD486RG, DRD430RGA, DRD450RGA, DRD485RGA, DRD435RH, DRD455RH, and DRD486RH RCA model DTC-100 Samsung model SIR-S60W Samsung model TS-160 Samsung models SIR-S70, SIR-S75, SIR-S300W, and SIR-S310W Sony models SAT-A1 and SAT-B1 Sony models SAT-A2 and SAT-B2 Sony models SAT-A3, SAT B3, SAT-A4, and SAT-B4 Sony models SAT-A50, SAT-A55, SAT-B50, SAT-B55, and SAT-HD100 Sony models SAT-A65, SAT-A65A, SAT-B65, and SAT-B65A Toshiba model DST-3000 Uniden model UDS100 Zenith model DTV1080 0749 1749 0566 0866 0819 0749 0247 0701 1076 0099 0749 0566 0766 0866 0566 0766 0392
0492 1109 1256 1309 0639 0739 0839 0939 1039 1749 0724 1856
10
Setup Codes for DIRECTV DVRs:
Hughes Net. Sys./TiVo model GXCEBOT Philips/TiVo model DSR6000R RCA UltimateTV model DWD490RE Sony/TiVo model SAT-T60 Sony UltimateTV model SAT-W60 1142 (program under DIRECTV mode) 1142 (program under DIRECTV mode) 1492 (program under DIRECTV mode) 1639 (program under DIRECTV mode) 1739 (program under DIRECTV mode)
PROGRAMMING OTHER DEVICE CONTROL
The DIRECTV® Universal Remote Control is also preprogrammed to operate an RCA TV, an RCA VCR, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section:
NOTE: To control a DVD/DVR player, program the VCR key. For TV/VCR Combo control, skip this section and perform the instructions on the next page.
1.
Turn on a device and, if applicable, insert a video cassette or DVD.
NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
2.
On the DIRECTV Universal Remote Control, press the device key you wish to program once (e.g., TV, VCR, or AUX). Press and hold Setup until the selected device key blinks twice and then release Setup. Use the Manufacturer's Codes (starting on page 14) to locate the four digit number corresponding to the brand name of the device you want to control. Enter the first four-digit code for your device. If performed correctly, the light under the select device key will blink twice.
NOTE: If the selected device key emits a long blink, the code is invalid. Repeat steps 2 through 3 and try entering the same code again.
continued on next page...
3.
11
PROGRAMMING OTHER DEVICE CON ...
