User manual DUAL XD5220

INSTALLATION/OWNER'S MANUAL AM/FM/CD Receiver with Detach Face XD5220 XD5220 INSTALLATION Preparation Please read entire manual before installation. Before You Start · Disconnect negative battery terminal. Consult a qualified technician for instructions. · Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started · Remove 2 transit screws located on top of the unit. · Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. · Install mounting sleeve into opening, bending tabs to secure. · Connect wiring harness and antenna. Consult a qualified technician if you are unsure. · Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). · Test for correct operation and slide into mounting sleeve to secure. · Snap trim ring into place. TYPICAL FRONT-LOAD DIN MOUNTING METHOD 2 XD5220 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XD5220 uses one 5 amp AGC fuse (Battery) located in-line. * CAUTION - Do not attach any speaker leads to ground as severe damage will occur. 3 XD5220 OPERATION Control Locations 1 2 3 4 5 6 7 8 9 20 19 18 17 16 15 14 13 12 11 10 1 2 3 4 5 6 7 8 9 10 Release Power Volume Up/Down Audio Play/Pause Bass Boost/Mono/Stereo Tune/Track Up/Down Band Eject Mute 11 12 13 14 15 16 17 18 19 Auto Store/Preset Scan Display Scan Local/Distance Preset 6 Preset 5 Preset 4 Preset 3/CD Intro Preset 2/CD Random Preset 1/CD Repeat 20 4 XD5220 OPERATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32" Phillips head screw through left side of mounting frame into faceplate. Press PWR or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press PWR to turn the unit off. Insert a CD or press Semi-permanent Faceplate Installation Power On/Off CD Mode Tuner Mode Bass Boost l/ II to begin or resume playback. Press PWR or BAND to begin or resume tuner operation. Press BASS to activate and deactivate bass boost curve. Activating this feature will enhance the bass frequencies when listening to music at all volumes. Adjust volume using VOL t / VOL s (00-46). Press MUTE to silence the audio. "MUTE" will appear in the display. Press MUTE again to cancel. Press DISP to display the clock. The radio frequency (tuner mode) or CD track/elapsed time (CD player mode) show by default. Press DISP to display the clock, then release. Press and hold DISP for 2 seconds, the clock will begin to flash. Press TUNE << to adjust the hours and TUNE >> to adjust the minutes. Clock settings will be saved after 5 seconds. The clock will display 12-hour AM/PM time in U.S. frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). Volume Mute Display Set the Clock 12/24-hour Clock 5 XD5220 OPERATION General Operation Reset Press and hold for more than 2 seconds to RESET the unit upon initial installation. The RESET button is located behind the faceplate. Refer to page 2 for details. Audio Press AUD to select between Volume (default), Bass, Treble, Balance & Fader. VOLUME BASS TREBLE BALANCE FADER Bass Press AUD until BA appears Press VOL t or s to adjust ( -7 minimum / 7 maximum) Treble Press AUD until TR appears Press VOL t or s to adjust ( -7 minimum / 7 maximum) Balance Press AUD until B appears Press VOL t (LEFT) or s (RIGHT) to adjust (BL 15/BR 15) BAL 00 represents equal balance. Fader Press AUD until F appears Press VOL t (FRONT) or s (REAR) to adjust (FF 15/FR 15) F 00 represents equal balance. 6 XD5220 OPERATION Tuner Operation Seek Tuning Manual Tuning Press TUNE << or >> momentarily to seek the next strong station. Press TUNE << or >> for more than 2 seconds, then release. "MANU" will momentarily appear in the display. Press TUNE << or >> momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCAN again to cancel. Press LOC to activate local tuning for strong FM station reception only. Press LOC again to cancel and resume distance tuning (default). Press MO/ST for more than 2 seconds during FM tuner operation to select mono or stereo (default) reception of the broadcast signal. Press BAND to select between FM1, FM2, FM3 and AM1, AM2 bands. Press and hold BAND then press TUNE << to select European frequency spacing. Press and hold BAND then press TUNE >> to select U.S. frequency spacing (default). Anytime frequency spacing is changed, all station presets are erased. Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band. Press AS/PS for less than 2 seconds to scan presets 1-6 on the current band, pausing for 5 seconds at each. Press AS/PS again to cancel. Scan Tuning FM Local/Distance FM Mono/Stereo Band Frequency Spacing Storing and Recalling Station Presets Automatically Store Stations Preset Scan 7 XD5220 OPERATION CD Player Operation Insert CD With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Eject CD Press EJECT to eject the CD. The unit will change to tuner mode. If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD. Track Select Press TRACK >> to skip to the beginning of the next track. Press TRACK << to return to the beginning of the current track. Pressing TRACK << again skips to the beginning of the previous track. Fast Forward and Reverse Press and hold TRACK >> or TRACK << to fast forward or reverse a track. Pause Press Press l// II to temporarily stop CD playback. l II again to resume playback. Intro Press INT to play the first 10 seconds of each track. Press INT to cancel. Press RPT to continuously repeat selected track. Press RPT to cancel. Press RDM to play all tracks in random order. Press RDM again to cancel. Random mode is retained in memory when selecting between tuner, CD player and auxiliary input modes and when the unit is turned on/off. Repeat Random CD-R/CD-RW Compatibility Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. 8 XD5220 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period. Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A. What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. What to do? 1. Before you call for service, check the troubleshooting guide in your owner's manual. A slight adjustment of any custom controls or connections discussed in your instruction booklet may save you a service call. 2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center. 3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment. 4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods: · Call us toll-free at 1-866-382-5476 · Email us at cs@dualav.com Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company's negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages. 9 XD5220 OPERATION Troubleshooting Problem Unit will not turn on (no power) Cause Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Speaker wires not connected One or more speaker wires touching each other or touching chassis ground Yellow or red wire touching chassis ground Speaker wires touching chassis ground Incorrect fuse rating Unit is not mounted correctly or backstrap is not secure Physical defect in media (CD, CD-R or CD-RW) CD mechanism position out of alignment CD transit screws still in place Action Check connections for proper voltage (11~16VDC) Check connection to ground Replace fuse Check connections at speakers Insulate all bare speaker wires from each other and chassis ground Check for pinched wire Check for pinched wire Use fuse with correct rating Check mounting sleeve and backstrap support Check media for scratches Press EJECT for 3 seconds to reset CD mechanism position Remove 2 transit screws located on top of the unit. Unit has power (but no sound) Unit blows fuses Excessive skipping Unit will not accept a disc Error Codes Error Code ER-1 appears on display ER-2 appears on display ER-3 appears on display Disc error Mechanism error Servo error or disc is in upside down Cause Action Press eject or RESET Press eject or RESET Press eject or RESET 10 XD5220 OPERATION Specifications CD Player Signal-to-noise: >92dB Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz Total power output: 120 Watts Peak Power output: 30Wx4 @ 4 ohm, 14.4 VDC Operating voltage: 11-16 VDC, negative ground Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm) Design and specifications subject to change without notice. FM Tuner AM Tuner General 11 Dual Electronics Corp. 21318 64th Ave. South Kent, WA 98032 Toll Free: 1-866-382-5476 www.dualav.com ©2005 Dual Electronics Corp. NSA0805-V01