User manual DUAL XD6320

XD6320 INSTALLATION/OWNERS MANUAL AM/FM/CD Receiver with Detach Face XD6320 INSTALLATION Preparation Please read entire manual before installation. Before You Start · Disconnect negative battery terminal. (consult a qualified technician for instructions) · Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started · Remove 2 transit screws located on top of the unit. · Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. · Install mounting sleeve into opening, bending tabs to secure. · Connect wiring harness and antenna. (consult a qualified technician if you are unsure) · Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). · Test for correct operation and slide into mounting sleeve to secure. · Snap trim ring into place. · Mount the iplugTM adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8" Phillips head screws. TYPICAL FRONT-LOAD DIN MOUNTING METHOD 2 XD6320 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XD6320 uses one 10 amp ATM fuse located beside the wiring connector. 3 XD6320 OPERATION Control Locations 1 2 3 4 5 6 7 8 9 10 22 21 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 11 Release Power Volume Band/Play/Pause Mode Auto Store/Preset Scan Tune/Track Down Eject Tune/Track Up Display EQ 12 13 14 15 16 17 18 19 20 21 Tuner Scan Local/Distance Preset 6 Preset 5 Preset 4 Preset 3/Intro Preset 2/Random Preset 1/Repeat Audio Loudness 22 Mute 4 XD6320 OPERATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32" Phillips head screw through left side of mounting frame into faceplate. Press POWER or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off. Press MODE to select between tuner, CD player and auxiliary input. Modes of operation are indicated in the display. Press LOUD to activate and deactivate the loudness contour curve. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Adjust volume using rotary encoder (00-46). Press and hold POWER for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display. Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Press DISP to select between clock and radio frequency (tuner mode), clock and CD track/elapsed time (CD mode), or clock and AUX (AUX mode). With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE to adjust the hours and TUNE to adjust the minutes. Press DISP momentarily to save the selected time. Semi-permanent Faceplate Installation Power On/Off Mode Loudness Volume Programmable Turn-On Volume Preset EQ Curves Display Set the Clock nn ll 5 XD6320 OPERATION General Operation 12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). In tuner mode, press and hold DISP then press TUNE to select function priority display. "FREQ" will momentarily appear in the display. Note: "FUNC" will appear in CD or AUX modes. Radio frequency (tuner mode), CD track/elapsed time (CD mode) or AUX (AUX mode) will be displayed by default. Press and hold DISP then press TUNE to select time display priority. "TIME" will momentarily appear in the display. Clock will be displayed by default. Radio frequency or CD track/elapsed time accessed by pressing DISP momentarily. Programmable Display Priority ll nn Programmable Clock Priority Programs unit to display clock/no clock when unit is off. Press and hold MODE then press PRESET 1 to select clock priority on/off. "CLK ON" or "CLK OFF" will momentarily appear in the display. Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate. Press and hold AUDIO for 3 seconds to turn confirmation beep on/off. Press MUTE to silence the audio. "MUTE" will flash in the display. Press MUTE again to cancel. Reset Confirmation Beep Mute 6 XD6320 OPERATION General Operation Audio Press AUDIO to select between Volume (default), Bass, Treble, Balance & Fader. Bass Press AUDIO until BAS appears Rotate encoder left/right to adjust ( -6 minimum / +6 maximum) Press AUDIO until TRE appears Rotate encoder left/right to adjust ( -6 minimum / +6 maximum) Press AUDIO until BAL appears Rotate encoder left/right to adjust (BAL L 12-BAL 00-BAL R 12) BAL 00 represents equal balance Press AUDIO until FAD appears Rotate encoder left/right to adjust (FAD F 12-FAD 00-FAD R 12) FAD 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM, FM, CD, and AUX modes. This allows you to save the Bass and Treble settings separately for each mode. Example: FM tuner mode can have Bass +3 and Treble -1 while CD mode can have Bass +2 and Treble +2. Note: Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Treble Balance Fader Source Audio Memory 7 XD6320 OPERATION Tuner Operation Seek Tuning Press TUNE or TUNE next strong station. nn nn ll momentarily to seek the ll Manual Tuning Press TUNE or TUNE for more than 2 seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE or TUNE momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. nn ll Scan Tuning Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCAN again to cancel. Press LOC to activate local tuning for strong station reception only. Press LOC again to cancel and resume distance tuning (default). Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Press and hold BAND then press TUNE to select European frequency spacing. Press and hold BAND then press TUNE to select USA frequency spacing (default). Local/Distance Band Frequency Spacing nn ll Storing and Recalling Station Presets Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band. Automatic local/distance is activated during the initial band scan. Press AS/PS for less than 2 seconds to scan presets 1-6 on the current band, pausing for 5 seconds at each. Press AS/PS again to cancel. Automatically Store Stations Preset Scan 8 XD6320 OPERATION CD Player Operation Insert CD With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation (AM, FM, or auxiliary input). If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD. Press TRACK to skip to the beginning of the next track. Press TRACK to return to the beginning of the current track. Pressing TRACK again skips to the beginning of the previous track. Eject CD Track Select ll nn nn Fast Forward and Reverse Press and hold TRACK or reverse a track. Press Press ll or TRACK nn to fast forward Pause l// II to temporarily stop CD playback. l II again to resume playback. Intro Press INT to play the first 10 seconds of each track. Press INT again to cancel. Press RPT to continuously repeat selected track. Press RPT again to cancel. Press RDM to play all tracks in random order. Press RDM again to cancel. Random mode is retained in memory when selecting between tuner, CD player and auxiliary input modes and when the unit is turned on/off. Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. In addition, the following CDs may be incompatible with this unit: CDs exposed to extreme temperatures or direct sunlight for extended periods of time, CDs recorded in which a recording session failed or a re-recording was attempted and, or encrypted or copy-protected CDs which do not conform to the audio CD-DA red book recording standard. Repeat Random CD-R/CD-RW Compatibility 9 XD6320 WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship, under normal conditions, for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new or renewed product in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. During the One-Year Warranty Period: For One Year from the date of purchase, your product will be replaced with a new, renewed or comparable product (whichever is deemed necessary) if it becomes defective or inoperative. This is done without charge to you. Replacement products are warranted for the balance of the original warranty period. Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A. What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. What to do? If purchased within the USA: 1. Before you call for service, check your operating instruction booklet. A slight adjustment of any custom controls discussed in your instruction booklet may save you a service call. 2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with proof of the purchase date from the retailer to the Return Center address listed below. 3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment. 4. DUAL will pay the return shipping charges if the product is returned to an address within the 48 contiguous states. Dual Electronics Corp. Attn: Returns Center 21318 64th Ave. South Kent, WA 98032 U.S.A. Toll Free: 1-866-626-7863 If purchased outside the USA: Please return the unit to original place of purchase for warranty service. Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company's negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages. 10 XD6320 OPERATION Specifications CD Player Signal-to-noise: >92dB Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit FM Tuner Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz AM Tuner Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz General Total power output: 200 Watts Peak Power output: 50Wx4 @ 4 ohms, 14.4 VDC Operating voltage: 11-16 VDC, negative ground Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm) Design and specifications subject to change without notice. 11 XD6320 WARRANTY Troubleshooting Problem Unit will not turn on (no power) Cause Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Black wire not connected Fuse blown Speaker wires not connected One or more speaker wires touching each other or touching chassis ground Yellow or red wire touching chassis ground Speaker wires touching chassis ground Incorrect fuse rating Unit is not mounted correctly or backstrap is not secure Physical defect in media (CD, CD-R or CD-RW) Disc read error Focus error or disc is in upside down CD mechanism position out of alignment CD transit screws still in place Action Check connections for proper voltage (11~16VDC) Check connection to ground Replace fuse Check connections at speakers Insulate all bare speaker wires from each other and chassis ground Check for pinched wire Check for pinched wire Use fuse with correct rating Check mounting sleeve and backstrap support Check media for scratches Press eject or RESET Press eject or RESET Press EJECT for 3 seconds to reset CD mechanism position Remove 2 transit screws located on top of the unit Unit has power (but no sound) Unit blows fuses Excessive skipping ERROR-01 appears on display ERROR-02 appears on display Unit will not accept a disc Dual Electronics Corp. 21318 64th Ave. South Kent, WA 98032 Toll Free: 1-866-626-7863 www.dualav.com ©2005 Dual Electronics Corp. All rights reserved. NSA0205-V01