User manual DUAL XDM7510

INSTALLATION/OWNER'S MANUAL AM/FM/CD/MP3/WMA Receiver with Detach Face XDM7510 XDM7510 INSTALLATION Preparation Please read entire manual before installation. Before You Start · Disconnect negative battery terminal. Consult a qualified technician for instructions. · Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started · Remove trim ring from unit, · Remove 2 transit screws located on top of the unit. · Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. · Install mounting sleeve into opening, bending tabs to secure. · Connect wiring harness and antenna. Consult a qualified technician if you are unsure. · Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). · Test for correct operation and slide into mounting sleeve to secure. · Snap trim ring into place. · Mount the iplugTM adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8" Phillips head screws. TYPICAL FRONT-LOAD DIN MOUNTING METHOD 2 XDM7510 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDM7510 uses one 10 amp ATM fuse located beside the wiring connector. 3 XDM7510 OPERATION Control Locations 1 2 3 4 5 6 7 8 9 10 11 12 13 23 22 21 20 19 18 17 16 15 14 1 2 3 4 5 6 7 8 9 10 Open Tune/Track Down AS/PS/Enter Mode/Search Tune/Track Up Audio Volume Loudness Tuner Scan/*8 Local/Distance/*7 Display/*0 EQ/*9 13 14 15 16 17 18 19 20 21 22 Eject Mute Preset 6/Folder Up Preset 5/Folder Down Preset 4 Preset 3/Intro Preset 2/Random Preset 1/Repeat Band/Play/Pause Power Reset 11 12 23 *Function buttons 7, 8, 9 and 0 apply to MP3/WMA operation only. 4 XDM7510 OPERATION General Operation Front Panel Note: The front panel is semi-permanently attached during assembly. Please refer to the separate yellow instructions (before installation) to make the front panel removable. With the unit off, press OPEN to allow the front panel to slide down. Gently squeeze the release tab located on the bottom center underside and pull front panel down and away from unit to remove. To install, insert left side first, then push right side to secure. Press PWR or any other button (except EJECT or OPEN) to turn the unit on. Inserting a disc will turn the unit on automatically. Press PWR to turn the unit off. Press MODE to select between tuner, CD player and auxiliary input. Modes of operation are indicated in the display. Press LOUD to activate and deactivate loudness contour curve. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Adjust volume using rotary encoder (00-46). Press and hold PWR for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display. Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Press DISP to select between clock and radio frequency (tuner mode), clock and CD track/elapsed time (CD mode), or clock and AUX (AUX mode). With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE to adjust the hours and TUNE to adjust the minutes. Press DISP momentarily to save the selected time. Front Panel Removal Power On/Off Mode Loudness Volume Programmable Turn-On Volume Preset EQ Curves Display Set the Clock ll nn 5 XDM7510 OPERATION General Operation 12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). In tuner mode, press and hold DISP then press TUNE to select function priority display. "FREQ" will momentarily appear in the display. Note: "FUNC" will appear in CD or AUX modes. Radio frequency (tuner mode), CD elapsed time/track (CD mode) or AUX (AUX mode) will be displayed by default. Note: When playing MP3/WMA files, the track number/elapsed time, track name, directory name, title, artist, album, year or comment will be displayed by default. Clock is accessed by pressing DISP momentarily. Press and hold DISP then press TUNE to select time display priority. "TIME" will momentarily appear in the display. Clock will be displayed by default. Radio frequency (tuner mode), CD elapsed time/track or MP3/WMA file information (CD mode) is accessed by pressing DISP momentarily. Programmable Clock Priority Programs unit to display clock/no clock when unit is off. Press and hold MODE then press PRESET 1 to select clock priority on/off. "CLK ON" or "CLK OFF" will momentarily appear in the display. Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs. The reset button is located above the PWR button. Press and hold AUD for 3 seconds to turn confirmation beep on/off. Press MUTE to silence the audio. "MUTE" will flash in the display. Press MUTE again to cancel. Programmable Display Priority ll nn Reset Confirmation Beep Mute 6 XDM7510 OPERATION General Operation Audio Press AUD to select between Volume (default), Bass, Treble, Balance & Fader. VOLUME BASS TREBLE BALANCE FADER Bass Treble Balance Press AUD until BAS appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press AUD until TRE appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press AUD until BAL appears then rotate encoder left/right to adjust (BAL L 12-BAL 00-BAL R 12). BAL 00 represents equal balance Press AUD until FAD appears then rotate encoder left/right to adjust (FAD F 12-FAD 00-FAD R 12). FAD 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM, FM, CD, and AUX modes. This allows you to save the Bass and Treble settings separately for each mode. Example: FM tuner mode can have Bass +3 and Treble -1 while CD mode can have Bass +2 and Treble +2. Note: Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Fader Source Audio Memory 7 XDM7510 OPERATION Tuner Operation Seek Tuning Manual Tuning Press TUNE or TUNE next strong station. nn nn ll momentarily to seek the ll ll Press TUNE or TUNE for more than 2 seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE or TUNE momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. nn Scan Tuning Local/Distance Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCAN again to cancel. Press LO/DX to activate local tuning for strong station reception only. Press LO/DX again to cancel and resume Distance tuning (default). Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Press and hold BAND then press TUNE to select European frequency spacing. Press and hold BAND then press TUNE to select USA frequency spacing (default). Band Frequency Spacing nn ll Storing and Recalling Station Presets Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Note: Function buttons 7, 8, 9 and 0 apply to MP3/WMA operation only. Automatically Store Stations Preset Scan Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band. Automatic Local/Distance is activated during the initial band scan. Press AS/PS for less than 2 seconds to scan presets 1-6 on the current band, pausing for 5 seconds at each. Press AS/PS again to cancel. 8 XDM7510 OPERATION CD Player Operation Insert CD Eject CD With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation (AM, FM, or auxiliary input). If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD. Press TRACK to skip to the beginning of the next track. Press TRACK to return to the beginning of the current track. Pressing TRACK again skips to the beginning of the previous track. Track Select ll nn nn Fast Forward and Reverse Pause Intro Repeat Random Press and hold TRACK or reverse a track. Press Press ll or TRACK nn to fast forward l// II to temporarily stop CD playback. l II again to resume playback. Press INT to play the first 10 seconds of each track. Press INT again to cancel. Press RPT to continuously repeat selected track. Press RPT again to cancel. Press RDM to play all tracks in random order. Press RDM again to cancel. Random mode is retained in memory when selecting between tuner, CD player and auxiliary input modes and when the unit is turned on/off. Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. In addition, the following CDs may be incompatible with this unit: CDs exposed to extreme temperatures or direct sunlight for extended periods of time, CDs recorded in which a recording session failed or a re-recording was attempted and, or encrypted or copy-protected CDs which do not conform to the audio CD-DA red book recording standard. CD-R/CD-RW Compatibility 9 XDM7510 OPERATION CD Player Operation - MP3/WMA Files Playing an MP3/WMA Disc When an MP3/WMA encoded disc is first inserted, "READING" will appear in the display. Depending on the number of files and folders, this may take several seconds. The icon will illuminate anytime a valid MP3 encoded disc is inserted and flash in MP3 search/navigate modes. The icon will illuminate anytime a valid WMA encoded disc is inserted and flash in WMA search/navigate modes. The icon will illuminate anytime a folder is selected in the file/folder search modes. Press DISP to select between track number/elapsed time (default), clock, track name, directory name, title, artist, album, year and comment. "NO ID3 TAG" will be displayed if the MP3 file contains no ID3 tag information. "UNKNOWN" will be displayed if the WMA file contains no WMA tag information. "ROOT" will be displayed if the directory name of a root folder is not labeled. Character Support Maximum character display information · Track name ­ 32 character maximum · Directory name ­ 32 character maximum · *Song title ­ 30 character maximum · *Artist name ­ 30 character maximum · *Album name ­ 30 character maximum · *Year ­ 4 character maximum · *Comment ­ 28 character maximum *Song title, Artist Name, Album name, Year and Comment will only be displayed if included with the MP3/WMA file. When referring to MP3/WMA playback, the following terms are synonymous: · File name and track name · Folder name and directory name 10 MP3 Icon WMA Icon Folder Icon Displaying Information XDM7510 OPERATION CD Player Operation - MP3/WMA Files Refer to the following button function table when selecting, searching or navigating MP3/WMA files and folders: MP3/WMA Button Function Table Button SEARCH Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 7 8 9 0 AUD Rotary Encoder MUTE Function Direct Select, Search and Navigate Modes Enter/Confirm A, B, C, 1 D, E, F, 2 G, H, I, 3 J, K, L, 4 M, N, O, 5 P, Q, R, 6 S, T, U, 7 V, W, X, 8 Y, Z, /, 9 -, _, +, 0 Character Shift Character Select (A, B, C ~ 8, 9, 0) Character Backspace Direct Select, Search and Navigate Modes Press SEARCH for more than 3 seconds, to select between the following modes: · Direct File Select · Alphanumeric File or Folder Search · File or Folder Navigate Press SEARCH for more than 3 seconds, then release. "MP3 T " or "WMA T " will flash in the display. Use the buttons in the above table (3 keystroke maximum input), or the rotary encoder to enter the desired file number. Direct File Select Step 1 * * Step 2 Press to confirm the selected file number or wait for the input cycle to time out (approximately 5 seconds). If the file is not available, "NO FILE" will be displayed momentarily and the current file will continue to play. 11 XDM7510 OPERATION CD Player Operation - MP3/WMA Files Alphanumeric File or Folder Search Step 1 Press SEARCH for more than 3 seconds, then release. Press SEARCH again, an " " will flash in the display. Use the buttons in the table on page 11 (32 character maximum input) or the rotary encoder to enter the desired alphanumeric search characters. Press AUD to advance one character to the right. * Step 2 Step 3 Step 4 Press to initiate the selected alphanumeric search. Turn the rotary encoder to preview the search results. If the search returns a folder, the icon will illuminate. Press to select the desired file or folder. If a folder is selected, "/ /" will be displayed. Turn the rotary encoder to the right to begin searching files in the folder. Press to select the desired file within the folder. Step 5 Note: If the file is not available, "NO FILE" will be displayed momentarily and the current file will continue to play. File/Folder Navigate Step 1 Press SEARCH for more than 3 seconds, then release. Press SEARCH again two times to navigate files/folders on the disc. The current folder name will scroll one time followed by available files and folders. Turn the rotary encoder to preview files/folders in the current folder. If a folder is selected, the icon will illuminate. Press to select the desired file or folder. If a folder is selected, "/ / " will be displayed. Turn the rotary encoder to the right to begin searching files in the folder. Press to select the desired file within the folder. Step 2 Step 3 Step 4 *Folder Access (Up one level) When navigating folders (and "/ /" is displayed), press AUD to access the previous level (up one level). *Only available on MP3/WMA discs recorded with more than one folder. 12 XDM7510 OPERATION CD Player Operation - MP3/WMA Files Navigating Note After navigating by direct select, alphanumeric search or file/folder navigate modes, the track number and elapsed time will be displayed by default. Press DISP momentarily to select clock, track name, directory name, title, artist, album, year or comment. Press Press to select the previous folder. to select the next folder. *Folder Access *Folder access is only available on MP3/WMA discs recorded with more than one folder. File Repeat File Repeat (Current Folder Only) Press RPT momentarily to continuously repeat selected file. Press RPT again to cancel. Press RPT for more than 2 seconds to consecutively repeat all files in the current folder only. The icon will appear in the display when in folder repeat mode. Press RPT again to cancel. Press RDM momentarily to play all files on entire disc in random order. Press RDM again to cancel. Press RDM for more than 2 seconds to play all files in current folder only in random order. The icon will appear in the display when in folder random mode. Press RDM again to cancel. Press INT momentarily to play the first 10 seconds of each file on the entire MP3/WMA disc. Press INT again to cancel. Press INT for more than 2 seconds to play the first 10 seconds of each file in the current folder only. The icon will appear in the display when in folder intro mode. Press INT again to cancel. Note: File repeat (current folder only), folder random and folder intro is only available on MP3/WMA discs recorded with more than one folder. Disc Random Folder Random Disc Intro Folder Intro 13 XDM7510 OPERATION CD Player Operation - MP3/WMA Files Media Compatibility The following types of discs/files are compatible: · CD-ROM (ISO), CD-R, CD-RW · CD-DA · MP3 data · WMA data The following types of discs/files are not compatible: · WMA files that are protected by DRM (Digital Rights Management). · WMA lossless format · Discs recorded with Track At Once or packet writing · MP3 PRO format · MP3 playlists · WAV format Playback Order MP3/WMA playback sequence is based on recorded order of files and begins in the root folder of the disc. Any empty folders or folders that do not include MP3/WMA files are skipped. This unit may not play files in the order they were recorded in. Refer to your recording software's user's manual for more information. · ISO9660 level 1 · ISO9660 level 2 · Yellow Book MODE 1 · Yellow Book MODE 2 FORM 1 · Multi session · Maximum folders and files - 256 · Maximum folder levels - 8 · MPEG-1/2/2.5 Audio Layer-3 ISO9660 standards: · Maximum nested folder depth is 8 (including the root folder). · Valid characters for folder/file names are letters A-Z (all caps), numbers 0-9, and "_" (underscore). Some characters may not be displayed correctly, depending on the character type. · This device can play back discs in Joliet, Romeo, and other standards that conform to ISO9660. MP3/WMA written in the formats other than the above may not play and/or their file names or folder names may not be displayed properly. 14 Compatible Recording Formats XDM7510 OPERATION CD Player Operation - MP3/WMA Files Additional MP3/WMA Information An internal buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping. When playing a disc recorded with regular audio files (CD-DA or .WAV) and MP3/WMA files, the unit will play the MP3/WMA files only. Only MP3 files with filename extension (.mp3) can be played. Only WMA files with filename extension (.wma) can be played. Do not attempt to play discs which contain non-MP3/WMA files with the MP3/WMA extension. Sampling Frequency Rates MP3 WMA Transfer Bit rates MP3 WMA 8kHz ~ 48kHz 32kHz ~ 48kHz 8kbps ~ 320kbps constant Variable bit rates 32kbps ~ 192kbps constant Variable bit rates Note: Some files may not play or be displayed correctly, depending on sampling rates and bit rates. MP3 Tag Display Recommended Settings ID3 tags Version 1.x This model will not display ID3 Version 2.0 or greater tags. For best results, use the following settings when burning an MP3 disc: 128kbps or higher constant bit rate 44.1kHz or higher sampling frequency For best results, use the following settings when burning a WMA disc: 64kbps or higher constant bit rate 32kHz or higher sampling frequency 15 XDM7510 WARRANTY Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period. Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A. What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. What to do? 1. Before you call for service, check the troubleshooting guide in your owner's manual. A slight adjustment of any custom controls or connections discussed in your instruction booklet may save you a service call. 2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center. 3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment. 4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods: · Call us toll-free at 1-866-382-5476 · E-mail us at cs@dualav.com Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company's negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages. 16 XDM7510 OPERATION Specifications CD Player Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz Operating voltage: 11-16 VDC, negative ground Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm) Design and specifications subject to change without notice. FM Tuner AM Tuner General CEA-2006 Power Standard Specifications (reference: 14.4VDC +/- 0.2V, 20Hz~20kHz) Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms) 17 XDM7510 OPERATION Troubleshooting Problem Unit will not turn on (no power) Cause Action Yellow wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) Red wire not connected or incorrect voltage Black wire not connected Fuse blown Check connection to ground Replace fuse Check connections at speakers Insulate all bare speaker wires from each other and chassis ground Check for pinched wire Check for pinched wire Use fuse with correct rating Check mounting sleeve and backstrap support Press eject or RESET Press eject or RESET Press eject or RESET Press eject or RESET Write disc using WMA files that are not copy-protected Repeat search using valid parameters Write disc using valid audio files with .mp3 or .wma file extensions Press EJECT for 3 seconds to reset CD mechanism position Remove 2 transit screws located on top of the unit Unit has power (but no sound) Unit blows fuses Speaker wires not connected One or more speaker wires touching each other or touching chassis ground Yellow or red wire touching chassis ground Speaker wires touching chassis ground Incorrect fuse rating Excessive skipping Unit is not mounted correctly or backstrap is not secure Disc read error Focus error or disc is in upside down FAT error MP3/WMA decode error The WMA file is copy-protected by DRM (Digital Rights Management) Selected file is not available in direct or alphanumeric search modes The WMA file is copy-protected by DRM (Digital Rights Management) CD mechanism position out of alignment CD transit screws still in place Physical defect in media (CD, CD-R or CD-RW) Check media for scratches ERROR-01 appears on display ERROR-02 appears on display ERROR-03 appears on display ERROR-04 appears on display PROTECT appears on display NO FILE appears on display INVALID appears on display Unit will not accept a disc 18 XDM7510 OPERATION Notes 19 Dual Electronics Corp. Toll Free: 1-866-382-5476 www.dualav.com ©2006 Dual Electronics Corp. All rights reserved. Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and or other countries. NSA0206-V02