INSTALLATION/OWNER'SMANUAL XMReadyMultimediaReceiverwithDetachFace XDMR6850 An optional XM Satellite Radio Receiver may be connected to the XDMR6850. XM subscription is required for reception. For more information, visit XM's website at www.xmradio.com or call 1-877-XM-RADIO. Not available in Alaska or Hawaii. XDMR6850INSTALLATION Preparation Please read entire manual before installation. BeforeYouStart · Disconnect negative battery terminal. Consult a qualified technician for instructions. · Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. GettingStarted · Remove trim ring from unit, · Remove transit screws located on top of the unit. · Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. · Install mounting sleeve into opening, bending tabs to secure. · Connect wiring harness and antenna. Consult a qualified technician if you are unsure. · Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). · Test for correct operation and slide into mounting sleeve to secure. · Snap trim ring into place. · Mount the iplugTM adapter to any smooth clean surface using the supplied double-sided tape or # x 3/8" Phillips head screws. TYPICALFRONT-LOADDINMOUNTINGMETHOD XDMR6850INSTALLATION WiringDiagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDMR6850 uses one 10 amp ATM fuse located beside the wiring connector. 3 XDMR6850OPERATION ControlLocations-Receiver 1 2 3 4 5 6 20 19 18 17 16 15 14 13 12 11 10 9 8 7 1 2 3 4 5 6 7 8 9 10 Tune/Track Down Power/Eject Volume/Audio/Setup AS/PS/Enter/Function Tune/Track Up Infrared Sensor *Key #0/Preset #10 Preset #5/Folder Up *Key/Preset #9/EQ Preset #/Folder Down 11 12 13 14 15 16 17 18 19 20 *Key/Preset #8/Tuner Scan Preset #3/Intro *Key/Preset #7/Return Preset #/Random Preset #6/Menu Preset #1/Repeat Mode/Shift/Search Display Record Band/Play/Pause/Scroll An optional XM Satellite Radio Receiver may be connected to the XDMR6850. XM subscription is required for reception. For more information, visit XM's website at www.xmradio.com or call 1-877-XM-RADIO. Not available in Alaska or Hawaii. *Function keys 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only. XDMR6850OPERATION ControlLocations-Remote 1 2 3 19 4 5 6 7 8 18 17 16 15 14 13 9 10 11 12 1 2 3 4 5 6 7 8 9 10 Power/Eject Volume Up AS/PS/Enter/Function Audio/Setup Tune/Track Up *Key #0/Preset #10 Volume Down Preset #3/Intro Preset #/Random Preset #6/Menu 11 12 13 14 15 16 17 18 19 *Key/Preset #9/EQ *Key/Preset #8/Tuner Scan *Key/Preset #7/Return Preset #5/Folder Up Preset #/Folder Down Preset #1/Repeat Mode/Search/Shift Tune/Track Down Band/Play/Pause/Scroll 5 XDMR6850OPERATION GeneralOperation FrontPanelNote: Thefrontpanelissemi-permanentlyattachedduring assembly.Pleaserefertotheseparateyellowinstructions (beforeinstallation)tomakethefrontpanelremovable. With the unit off, press EJECT to allow the front panel to slide down. Gently squeeze the release tab located on the bottom center underside and pull front panel down and away from unit to remove. To install, insert left side first, then push right side to secure. Press PWR for seconds or any other button momentarily to turn the unit on. Inserting a disc will turn the unit on automatically. Press PWR for seconds to turn the unit off. Press MODE to select between AM/FM, *XM Radio, CD player and auxiliary input. Modes of operation are indicated in the display. *Optional XM Satellite Radio Receiver and subscription required for XM Radio operation. Adjust volume using rotary encoder (00-6). Press SHIFT for seconds to activate the SHIFT function. The SHIFT icon will appear in the display. In XM Radio mode, the SHIFT function must be active to access the EQ function. Press SHIFT again for seconds to cancel. Press EQto select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). When in AM/FM, CD or AUX mode: Press DISP to select between clock and radio frequency (tuner mode), clock and CD elapsed time/track (CD mode), or clock and AUX (AUX mode). When in XM Radio mode: Press DISP to select between channel name, artist name, song title or clock. SettheClock With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE to adjust the hours and to adjust the minutes. Press DISP momentarily to TUNE save the selected time. FrontPanelRemoval PowerOn/Off Mode Volume ShiftFunction (XM Radio only) PresetEQCurves Display ll nn 6 XDMR6850OPERATION GeneralOperation-SetupMenu 12/24-hourClock The clock will display 1-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display -hour time (:00). SetupMenu Press and hold the rotaryencoder for more than 3 seconds to access the setup menu. Press the rotaryencoder momentarily to select between the menu functions and rotate the rotaryencoder left/right to adjust or activate the desired function. MenuFunction LoudnessCurve Options LOUD OFF LOUD ON Action Disables the loudness function. Enables the loudness function. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Radio frequency (tuner mode), XM information (XM mode), CD elapsed time/track or MP3/WMA file information (CD mode) or AUX (AUX mode) will be displayed by default. Clock is accessed by pressing DISPmomentarily. Clock will be displayed by default. Radio frequency (tuner mode), XM information (XM mode), CD elapsed time/track or MP3/WMA file information (CD mode) is accessed by pressing DISP momentarily. Programs the unit to USA tuner spacing. (00kHz for FM and 10kHz for AM) Programs the unit to European tuner spacing. (50kHz for FM and 9kHz for AM) Programs the unit to not display the clock when the power is off. Programs the unit to display the clock when the power is off. Enables access to auxiliary mode. Disables access to auxiliary mode. Disables the confirmation beep. Enables the confirmation beep. Activates Distance tuning. Activates Local tuning for strong station reception only. ClockDisplay Priority FUNC PRI CLK PRI TunerFrequency FREQ USA Spacing FREQ EUR ClockDisplay CLK OFF CLK ON AuxiliaryMode Beep Confirmation Local/Distance Tuning AUX ON AUX OFF BEEP OFF BEEP ON LOC OFF LOC ON 7 XDMR6850OPERATION GeneralOperation Audio Press rotaryencoder momentarily to select between Volume (default), Bass, Treble, Balance, & Fader. VOLUME BASS TREBLE BALANCE FADER Bass Treble Balance Press rotaryencoder until BAS appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press rotaryencoder until TRE appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press rotaryencoder until BAL appears then rotate encoder left/right to adjust (BAL L 1-BAL 00-BAL R 1). BAL 00 represents equal balance Press rotaryencoder until FAD appears then rotate encoder left/right to adjust (FAD F 1-FAD 00-FAD R 1). FAD 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM, FM, CD, XM, and AUX modes. This allows you to save the Bass and Treble settings separately for each mode. Note: Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Fader SourceAudioMemory Reset Press RESET upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate. This feature is available when used with the EAUSB0 Media Link Adapter (sold separately). This feature is available when used with the EAUSB0 Media Link Adapter (sold separately). This feature is available when used with the EAUSB0 Media Link Adapter (sold separately). Record Menu Return 8 XDMR6850OPERATION SeekTuning ManualTuning AM/FMTunerOperation Press TUNE nn or TUNEll momentarily to seek the next strong station. Press TUNE or TUNE for more than seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE or TUNE momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. nn ll nn ll ScanTuning Press SCN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCN again to cancel. Band Press BAND to select between FM1, FM, FM3, AM1 and AM bands. StoringandRecalling Up to 18 FM stations and 1 AM stations can be stored. To StationPresets store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Note: Function keys 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only. AutomaticallyStore Press AS/PS for more than seconds to automatically store Stations the six strongest stations in the current band. Automatic Local tuning is activated during the initial band scan. PresetScan Press AS/PS for less than seconds to scan presets 1-6 on the current band, pausing for 5 seconds at each. Press AS/PS again to cancel. 9 XDMR6850OPERATION XMRadioActivation ActivatingYourXMReceiver (whenconnected) 1. Press MODE to select XM Radio. . Verify channel 1 (XM Preview Channel) is playing. 3. Select Channel 0. The XM receiver's eight character Radio ID number will appear on the XDMR6850 display. The Radio ID number is also located on the XM receiver unit (sold separately). . Record the number here for future reference: 5. Activate your XM Satellite Radio service. To subscribe, log onto http://www.xmradio.com/activation or call 1-800-967-36. Note: You will need to keep your XDMR6850 turned on for at least one hour after requesting activation to receive the full channel line-up. XMRadioOperation TuningModes BasicChannelSelection DirectChannelSelection Press BAND to select between XM DIRECT, XM1 and XM bands. Press TUNE or TUNE momentarily to select the next available channel. Press and hold to advance quickly. Press BAND to select XM DIRECT channel entry band. "DIRECT" will momentarily appear in the display. Enter the desired channel using buttons 1-0, then press FUNC for 3 seconds to confirm the selected channel. If the channel is not available, the current channel will be retained. Press FUNC once to display the category of the currently selected channel for seconds. The CATEGORY icon will appear on the display. nn ll CategoryRecall 10 XDMR6850OPERATION XMRadioOperation ChannelSearchby Category Press FUNC once, the CATEGORY icon will appear on the display. Press or to choose a different category, then press TUNE or TUNE to choose a channel within that category. Press FUNC for 3 seconds to select the desired channel. If you do not select a channel, the channel search will time out after several seconds and the current channel will be retained. nn ll ChannelSearchbyName Press FUNC twice, the SEARCH icon will appear on the display. Use the rotary encoder to select the desired alphanumeric channel name. Press to enter each character or to clear the entry. Press FUNC for more than 3 seconds to begin the channel name search. Press TUNE or TUNE to review the channel search results. Press FUNC for 3 seconds to select the desired channel. If you do not select a channel, the channel search will time out after several seconds and the current channel will be retained. If the search results are not valid, "NOTFOUND" will momentarily appear on the display and current channel will be retained. nn ll StoringandRecalling PresetChannels Up to 0 XM channels can be stored. To store a channel, select XM1 or XM band and the desired channel. Press and hold the desired preset button (1-0) for more than seconds. When stored, the preset number will momentarily appear in the display. The channel can be recalled anytime by pressing the corresponding preset button. Note: Presets 7, 8, 9 and 0 apply to XM Radio operation only. DisplayOptions Press DISP to select between the following display options: The selected display option will be retained in memory (when changing channels for instance). TextScrolling Press SCROLL for more than 3 seconds to activate continuous text scrolling. The current channel name, artist name or song title will scroll continuously (if more than 8 characters). Press SCROLL for more than 3 seconds again to cancel continuous text scrolling. 11 XDMR6850OPERATION CDPlayerOperation InsertCD EjectCD With the label facing up, insert a standard ...