INSTALLATION/OWNER'S MANUAL XM Ready Multimedia Receiver with Detach Face XDMR7710 An optional XM Satellite Radio Receiver may be connected to the XDMR7710. XM subscription is required for reception. For more information, visit XM's website at www.xmradio.com or call 1-877-XM-RADIO. Not available in Alaska or Hawaii. XDMR7710 INSTALLATION Preparation Please read entire manual before installation. Before You Start · Disconnect negative battery terminal. Consult a qualified technician for instructions. · Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started · Remove trim ring from unit, · Remove 2 transit screws located on top of the unit. · Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. · Install mounting sleeve into opening, bending tabs to secure. · Connect wiring harness and antenna. Consult a qualified technician if you are unsure. · Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). · Test for correct operation and slide into mounting sleeve to secure. · Snap trim ring into place. · Mount the iplugTM adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8" Phillips head screws. TYPICAL FRONT-LOAD DIN MOUNTING METHOD 2 XDMR7710 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDMR7710 uses one 10 amp ATM fuse located beside the wiring connector. 3 XDMR7710 OPERATION Control Locations - Receiver 1 2 3 4 5 6 7 8 9 10 11 12 13 14 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 EQ Mode/Search Display Preset #2/Random Preset #1/Repeat Open Volume Eject Preset #6/Menu *Key/Preset #7/Return Tune/Track Down Folder Up AS/PS/Enter/Function Tune/Track Up 15 16 17 18 19 20 21 22 23 Folder Down *Key/Preset #8/Tuner Scan *Key/Preset #9 *Key #0/Preset #10 Band/Play/Pause/Scroll Infrared Sensor Power Preset #5 Preset #4 Preset #3/Intro Reset Audio/Setup Record 24 25 26 27 11 12 13 14 *Function keys 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only. 4 XDMR7710 OPERATION Control Locations - Remote 1 2 3 19 4 5 6 18 17 16 15 14 7 8 9 10 13 11 12 1 2 3 4 5 6 7 8 9 10 Power Volume Up AS/PS/Enter/Function Audio/Setup Tune/Track Up *Key #0/Preset #10 Volume Down Preset #3/Intro Preset #2/Random Preset #6/Menu 11 12 13 14 15 16 17 18 19 *Key/Preset #9 *Key/Preset #8/Tuner Scan *Key/Preset #7/Return Preset #5 Preset #4 Preset #1/Repeat Mode/Search Tune/Track Down Band/Play/Pause/Scroll 5 XDMR7710 OPERATION General Operation Front Panel Note: The front panel is semi-permanently attached during assembly. Please refer to the separate yellow instructions (before installation) to make the front panel removable. With the unit off, press OPEN to allow the front panel to slide down. Gently squeeze the release tab located on the bottom center underside and pull front panel down and away from unit to remove. To install, insert left side first, then push right side to secure. Press POWER or any other button (except EJECT or OPEN) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off. Press MODE to select between AM/FM, *XM Radio, CD player and auxiliary input. Modes of operation are indicated in the display. *Optional XM Satellite Radio Receiver and subscription required for XM Radio operation. Adjust volume using rotary encoder (00-46). Press and hold POWER for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display. Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). When in AM/FM, CD or AUX mode: Press DISP to select between clock and radio frequency (tuner mode), clock and CD elapsed time/track (CD mode), or clock and AUX (AUX mode). When in XM Radio mode: Press DISP to select between channel name, artist name, song title or clock. Set the Clock With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE to adjust the hours and TUNE to adjust the minutes. Press DISP momentarily to save the selected time. Front Panel Removal Power On/Off Mode Volume Programmable Turn-On Volume Preset EQ Curves Display ll nn 6 XDMR7710 OPERATION General Operation - Setup Menu 12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). Press and hold SETUP for more than 3 seconds to access the setup menu. Press SETUP momentarily to select between the menu functions and rotate the rotary encoder left/right to adjust or activate the desired function. Action Disables the loudness function. Enables the loudness function. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Radio frequency (tuner mode), XM information (XM mode), CD elapsed time/track or MP3/WMA file information (CD mode) or AUX (AUX mode) will be displayed by default. Clock is accessed by pressing DISP momentarily. Clock will be displayed by default. Radio frequency (tuner mode), XM information (XM mode), CD elapsed time/track or MP3/WMA file information (CD mode) is accessed by pressing DISP momentarily. Programs the unit to USA tuner spacing. (200kHz for FM and 10kHz for AM) Programs the unit to European tuner spacing. (50kHz for FM and 9kHz for AM) Programs the unit to not display the clock when the power is off. Programs the unit to display the clock when the power is off. Enables access to auxiliary mode. Disables access to auxiliary mode. Disables the confirmation beep. Enables the confirmation beep. Activates Distance tuning. Activates Local tuning for strong station reception only. Setup Menu Menu Function Loudness Curve Options LOUD OFF LOUD ON Clock Display Priority FUNC PRI CLK PRI Tuner Frequency FREQ USA Spacing FREQ EUR Clock Display CLK OFF CLK ON Auxiliary Mode Beep Confirmation Local/Distance Tuning AUX ON AUX OFF BEEP OFF BEEP ON LOC OFF LOC ON 7 XDMR7710 OPERATION General Operation Audio Press AUDIO momentarily to select between Volume (default), Bass, Treble, Balance, & Fader. VOLUME BASS TREBLE BALANCE FADER Bass Treble Balance Press AUDIO until BAS appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press AUDIO until TRE appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press AUDIO until BAL appears then rotate encoder left/right to adjust (BAL L 12-BAL 00-BAL R 12). BAL 00 represents equal balance Press AUDIO until FAD appears then rotate encoder left/right to adjust (FAD F 12-FAD 00-FAD R 12). FAD 00 represents equal fader Individual Bass and Treble settings are retained in memory for AM, FM, CD, XM, and AUX modes. This allows you to save the Bass and Treble settings separately for each mode. Note: Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected). Fader Source Audio Memory Reset Press RESET upon initial installation or if abnormal operation occurs. Refer to page 4 for the reset button location. This feature is available when used with the EAUSB20 Media Link Adapter (sold separately). This feature is available when used with the EAUSB20 Media Link Adapter (sold separately). This feature is available when used with the EAUSB20 Media Link Adapter (sold separately). Record Menu Return 8 XDMR7710 OPERATION Seek Tuning Manual Tuning AM/FM Tuner Operation Press TUNE nn or TUNE ll momentarily to seek the next strong station. Press TUNE or TUNE for more than 2 seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE or TUNE momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. nn ll nn ll Scan Tuning Band Storing and Recalling Station Presets Press SCN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCN again to cancel. Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button. Note: Function keys 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only. Automatically Store Stations Preset Scan Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band. Automatic Local tuning is activated during the initial band scan. Press AS/PS for less than 2 seconds to scan presets 1-6 on the current band, pausing for 5 seconds at each. Press AS/PS again to cancel. 9 XDMR7710 OPERATION XM Radio Activation Activating Your XM Receiver (when connected) 1. Press MODE to select XM Radio. 2. Verify channel 1 (XM Preview Channel) is playing. 3. Select Channel 0. The XM receiver's eight character Radio ID number will appear on the XDMR7710 display. The Radio ID number is also located on the XM receiver unit (sold separately). 4. Record the number here for future reference: 5. Activate your XM Satellite Radio service. To subscribe, log onto http://www.xmradio.com/activation or call 1-800-967-2346. Note: You will need to keep your XDMR7710 turned on for at least one hour after requesting activation to receive the full channel line-up. XM Radio Operation Tuning Modes Basic Channel Selection Direct Channel Selection Press BAND to select between XM DIRECT, XM1 and XM2 bands. Press TUNE or TUNE momentarily to select the next available channel. Press and hold to advance quickly. Press BAND to select XM DIRECT channel entry band. "DIRECT" will momentarily appear in the display. Enter the desired channel using buttons 1-0, then press FUNC for 3 seconds to confirm the selected channel. If the channel is not available, the current channel will be retained. Press FUNC once to display the category of the currently selected channel for 10 seconds. The CATEGORY icon will appear on the display. nn ll Category Recall 10 XDMR7710 OPERATION XM Radio Operation Channel Search by Category Press FUNC once, the CATEGORY icon will appear on the display. Press or to choose a different category, then press TUNE or TUNE to choose a channel within that category. Press FUNC for 3 seconds to select the desired channel. If you do not select a channel, the channel search will time out after several seconds and the current channel will be retained. nn ll Channel Search by Name Press FUNC twice, the SEARCH icon will appear on the display. Use the rotary encoder to select the desired alphanumeric channel name. Press to enter each character or to clear the entry. Press FUNC for more than 3 seconds to begin the channel name search. Press TUNE or TUNE to review the channel search results. Press FUNC for 3 seconds to select the desired channel. If you do not select a channel, the channel search will time out after several seconds and the current channel will be retained. If the search results are not valid, "NOTFOUND" will momentarily appear on the display and current channel will be retained. nn ll Storing and Recalling Preset Channels Up to 20 XM channels can be stored. To store a channel, select XM1 or XM2 band and the desired channel. Press and hold the desired preset button (1-0) for more than 2 seconds. When stored, the preset number will momentarily appear in the display. The channel can be recalled anytime by pressing the corresponding preset button. Note: Presets 7, 8, 9 and 0 apply to XM Radio operation only. Display Options Press DISP to select between the following display options: The selected display option will be retained in memory (when changing channels for instance). Text Scrolling Press BAND for more than 3 seconds to activate continuous text scrolling. The current channel name, artist name or song title will scroll continuously (if more than 8 characters). Press BAND for more than 3 seconds again to cancel continuous text scrolling. 11 XDMR7710 OPERATION CD Player Operation Insert CD Eject CD With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation (AM, FM, XM, or auxiliary input). If the disc ...