INSTALLATION/OWNER'S MANUAL XDVD1002CM XDVD1002CM PREPARATION Table of Contents Safety Information...................................... 2-3 Before You Begin........................................ 3 Package Contents....................................... 4 Wiring Diagram............................................. 5 Mounting................................................. 6 Control Locations........................................... 7-8 General Operation...................................... 9 Setup Menu................................................. 10-11 DVD Operation............................................ 12-13 CD Operation............................................. 14 MP3 Operation........................................... 15 DivX Operation............................................ 16 Warranty..................................................... 17 Troubleshooting............................................ 18 Notes....................................................... 18 Specifications............................................ 19 Safety Information Please read all instructions carefully before attempting to install or operate. Due to its technical nature, it is highly recommended that your DUAL XDVD1002CM is installed by a professional installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only. Disconnect the vehicle battery's negative terminal before starting installation to prevent short circuits. (consult a qualified technician for instructions if you are unsure) Avoid installing the main unit where it would be subject to high temperatures, or where it would be subject to dust, dirt or excessive vibration. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVERS. NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. 2 XDVD1002CM PREPARATION Before You Begin Cautions To prevent damage or injury: 1. Make sure to ground the unit securely to the vehicle chassis ground. 2. Do not remove the top cover of the unit. 3. Do not install the unit in a spot exposed to excessive heat or the possibility of water splashing. 4. Do not subject the unit to excessive shock. 5. When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause the unit to malfunction. 6. To prevent short circuits when replacing a fuse, disconnect the wiring harness first. 7. Do not use any screws except the ones provided. 8. If you experience problems during installation, consult your nearest DUAL dealer. 9. To clean the monitor, wipe only with a dry silicone cloth or soft cloth. Do not use a stiff cloth, or volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or remove the printing. 10. When the temperature of the unit falls (as in winter), the liquid crystal inside the screen will become darker than usual. Normal brightness will return after using the monitor for a while. Additional Warnings To prevent injury and/or fire, take the following precautions: 1. Ensure that the unit is securely installed. 2. When extending the ignition, battery or ground cables, make sure to use automotive-grade cables or other cables with an area of 0.75mm (AWG 18) or more to prevent voltage drops and wire deterioration. 3. Do not touch the liquid crystal fluid if the LCD is damaged or broken. The liquid crystal fluid may be hazardous to your health or fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately. DVD Region Management Some DVD discs can be played only in certain playback modes according to the intentions of the software products. As this player plays discs according to their intentions, some functions may not work as intended by you. Please be sure to read the instructions provided with each disc. This player has been designed to play back the DVD software that has been encoded for specific region areas. It cannot play back the DVD software encoded for other region areas than the region areas for which is has been designed. The XDVD1002CM will play discs labeled "region 1" or "all". DVD region codes are: 1. USA, Canada 2. Japan, Europe, South Africa, Middle East 3. Asia 4. Australia, New Zealand, Mexico, South America 5. Russia, India 6. China 3 XDVD1002CM PREPARATION Contents Main Unit Remote Control Mounting Bracket Wiring Harness and Hardware 2 Pair Headphones Recommended Tools and Equipment · Upholstery hook tool (for removal of panels, if necessary) · #1 and #2 Phillips screwdrivers · Utility knife, razor knife, or shears · Misc. electrical connectors (to connect to vehicle power source ­ requirement will vary form vehicle to vehicle) · Wire strippers · Electrical tape · Masking tape · Multi-meter (to verify correct voltages and continuity ; It is not reccomended to use a test light or logic probe for this purpose) 4 XDVD1002CM INSTALLATION Wiring Diagram - Main Unit Yellow Black Red Brown Brown/Black A/V Output Connect to battery circuit or constant 12 volt source Connect to chassis ground Connect to ignition circuit or switched 12 volt source Dome light See notes below Dome light + See notes below Dome light trigger See notes below Connect to audio left, audio right, and composite video of external source Connect to audio left, audio right, and composite video of external monitor Green AUX2 Input Aux 2 Input (Red Jacket) A/V Output (Black Jacket) Wiring Notes: There are two common types of dome light circuits, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to turn the lights on. To determine which system you have, locate the wires at the dome light. Positive switched system: On a positive switched system, with all doors closed and lights out, both wires at the dome light will rest at ground. When the dome light is activated, one of these wires will switch to +12 vdc. This is your switched wire. For positive systems, connect the green wire (dome light trigger) to the switched wire. Then connect the brown wire (dome light -) to a fused constant + 12 vdc source, and the brown/black wire (dome light +) to a ground. Negative switched system: On a negative switched system, with all doors closed and lights out, both wires at the dome light will rest at +12 vdc. When the dome light is activated, one of these wires will switch to ground. This is your switched wire. For negative systems, connect the green wire (dome light trigger) to the switched wire. Then connect the brown/black wire (dome light +) to a fused constant + 12 vdc source, and the brown wire (dome light -) to a ground. Some vehicles incorporate transistorized control of the dome light circuit, and may not support the additional current draw of the unit's dome lights. On these vehicles it may be necessary to connect the green wire (dome light trigger) to a door pin switch wire. 5 XDVD1002CM INSTALLATION Mounting 1. Test fit the mounting bracket and unit on the ceiling of the vehicle, verifying that it is not going to interfere with the safe operation of the vehicle and is physically safe for the driver and passengers. 2. Once the mounting location is determined, carefully mark the location with masking tape. 3. Lower the vehicle's headliner down to see if a roof support beam is available to screw the mounting bracket to. If a support beam is not available, use a 3/4" piece of plywood cut to the appropriate size. Attach the plywood to the roof of the vehicle using silicone, allowing adequate drying time before proceeeding. 4. Screw the mounting bracket into the vehicle with installer supplied screws (not included). NOTE: Double check the length of the screws prior to mounting the bracket to avoid penetration of the vehicle's roof. 5. Cut a 1" hole in the headliner along the backside of the mounting bracket for the cables to pass through. Route cables and wire from wire harness through the hole. 6. Plug in the wire harness to the back of the unit. 7. Carefully hold the unit to the mounting bracket aligning the mounting holes while screwing in the mounting screws (included). NOTE: Make sure that all wires and cables are out of the way while mounting the unit. 8. Connect all cables and wires (see page 5 for details). NOTE: Make sure to keep the ground wire (black) of the unit as short as possible to help prevent unwanted audio noise pickup from the vehicle's systems. WARNING: Failure to properly follow these instructions could result in damge to the vehicle, it's electronic system, other property, personal injury and/or death. 6 XDVD1002CM OPERATION Control Locations - Main Unit 1 12 2 11 3 10 4 9 5 8 6 7 1 2 3 4 5 6 Power Source Select Chapter/Track Down Dome Light Switch Screen Release Aux1 Inputs 7 8 9 Rear IR Sensor Motorized Disc Slot Front IR Sensor/Transmitter 10 Chapter/Track Up 11 Play/Pause 12 Disc Eject 7 XDVD1002CM OPERATION Control Locations - Remote 1 2 3 4 1 32 Power Return Fast Reverse Enter Chapter/Track Down Root Menu Setup Menu Step Subtitle Dimmer Angle 5 6 7 8 9 10 11 2 31 3 30 4 29 5 28 12 Shuffle 13 Goto 14 Video/Source 15 Repeat 16 LCD Screen Menu 17 Program 18 Screen Mode 19 Screen Zoom 20 FM Transmitter 21 Title 22 Repeat A-B 23 24 25 26 27 28 29 30 31 32 Mute Audio Volume Up/Down Display Stop Play/Pause Chapter/Track Up Fast Forward Clear Eject 6 27 7 26 8 25 9 24 10 11 23 22 12 21 13 14 15 16 17 18 19 20 8 XDVD1002CM OPERATION General Operation Power On/Off Monitor Open/Close To turn on the unit, press the power button on the main unit or on the remote. Press again to turn the unit off. Pressing the screen release lock will unlock the LCD screen, and it will drop down slightly. Move the screen to the desired viewing angle, and the internal hinge assembly will hold the screen in position. Remember to turn the unit off and move the LCD Screen into the closed position when not in use. The lights integrated into the main unit are controlled by a push-button switch. Do not leave the vehicle unattended with the dome light switch on, as this could result in a discharged battery. There is an Infrared sensor located on the front of the main unit. This transmitter sends audio wirelessly to the included IR Headphones. Two pair of Infrared wireless headphones include built-in sensors to receive audio signals sent from theIR transmitter located on the main unit. These headphones are designed to operate within line of sight from the transmitter as infrared transmissions, like visible light travel only in a straight line, Headphone power and volume controls are located on the bottom of the right ear cup. NOTE: The headphone will auto power off after 2 minutes. This unit is equipped with an RF Modulator that allows you to listen to an audio signal through your existing FM radio. You can do this by tuning your vehicle's FM radio to any frequency between 88.3 and 90.1. Press the FMTX button on the remote control to select the frequency at which the unit will transmit to your FM radio. NOTE: The current frequency that is being transmitted will appear in the lower left of the LCD screen as you press the FMTX button on the remote. This frequency must match the frequency on your FM radio to receive audio signal. There are two sets of auxiliary inputs on this unit, both of which can be used to display an external audio/video source onto the main unit. Hook the external source up through the RCA jacks located on the back of the unit (AUX1), or on the installation wire harness (AUX2). Accessing these inputs is easily done by pushing SOURCE on the main unit, or by pressing SOURCE on the remote control. There is one set of audio/video outputs located on the installation wire harness. These can be used to get an audio/video signal from the main unit to external LCD monitors or video displays. Overhead Dome Lights IR Transmitter Wireless Headphones FM Transmitter Auxiliary Inputs Audio/Video Outputs 9 XDVD1002CM OPERATION General Operation - Setup Menu Selecting Sources - Main Unit Selecting Sources - Remote Volume Mute Display Display Mode Press SOURCE on the main unit to select between the following sources: AUX1 > AUX2 > DVD. Press SOURCE on the remote to select between AUX1 > AUX2 > DVD. Adjust volume using VOLUME / on the remote (0-16). Press MUTE on the remote to silence the audio. Press MUTE or VOLUME / to cancel. Press DISPLAY on the remote to select the status of each operating mode (elapsed time, etc). Press MODE on the remote to select between the following screen modes: Full screen displaying 16:9 image. Zoom display of 4:3 image Normal display of 4:3 image in the center. Press SETUP on the remote to select setup menu main page. Press or to select between menu options and press button on remote NOTE: To access the Preferences menu, DVD playback must be stopp ...