INSTALLATION/OWNER'S MANUAL DVD Multimedia Receiver with 2.5" TFT Display XDVD8130 Safety Note: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. XDVD8130 PREPARATION Table of Contents Page DVD Region Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information/Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mounting/Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Control Locations - Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control Locations - Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 General Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 AM/FM Tuner Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DVD Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-19 DVD Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22 CD Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24 MP3/WMA Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 DVD/MP3/WMA Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27 Navigation/Auxiliary Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DVD Region Management Some DVD discs can be played only in certain playback modes according to the intentions of the software. As the XDVD8130 plays discs according to their intentions, some functions may not work as intended. Please be sure to read the instructions provided with each disc. This player has been designed to play back DVD software that has been encoded for specific region areas. It cannot play back DVD software encoded for other region areas than the region areas for which it has been designed. The XDVD8130 will play discs labeled "Region 1" or "All". DVD region codes: 1 - USA, Canada 2 - Japan, Europe, South Africa, Middle East 3 - Rep. of Korea, Taiwan, Hong Kong, Parts of Southeast Asia 4 - Australia, New Zealand, Mexico, South America 5 - Eastern Europe, Russia, India, Africa 6 - China 2 XDVD8130 PREPARATION Safety Information Please read all instructions carefully before attempting to install or operate. Due to its technical nature, it is highly recommended that your DUAL XDVD8130 is installed by a professional installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only. Safety Notes: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. To prevent damage or injury: 1. Make sure to ground the unit securely to the vehicle chassis ground. 2. Do not remove the top or bottom covers of the unit. 3. Do not install the unit in a spot exposed to direct sunlight or excessive heat or the possibility of water splashing. 4. Do not subject the unit to excessive shock. 5. When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause the unit to malfunction. 6. To prevent short circuits when replacing a fuse, disconnect the wiring harness first. 7. Use only the provided hardware and wire harness. 8. You cannot view video while the vehicle is moving. Find a safe place to park and engage the parking brake. 9. If you experience problems during installation, consult your nearest DUAL dealer. 10. If the unit malfunctions, press the reset button first. If the problem still persists, consult your nearest DUAL dealer or call tech assistance @ 1-866-382-5476. 11. To clean the monitor, wipe only with a dry silicone cloth or soft cloth. Do not use a stiff cloth, or volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or remove the printing. 12. When the temperature of the unit falls (as in winter), the liquid crystal inside the screen will become darker than usual. Normal brightness will return after using the monitor for a while. Additional notes: 1. When extending the ignition, battery or ground cables, make sure to use automotivegrade cables or other cables with an area of 0.75mm (AWG 18) or more to prevent voltage drops. 2. Do not touch the liquid crystal fluid if the LCD is damaged or broken. The liquid crystal fluid may be hazardous to your health or fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately. 3 XDVD8130 INSTALLATION Preparation Please read entire manual before installation. Before You Start · Disconnect negative battery terminal. Consult a qualified technician for instructions. · Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started · Remove trim ring from unit. · Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. · Install mounting sleeve into opening, bending tabs to secure. · Connect wiring harness and antenna as shown on pages 5-6. Consult a qualified technician if you are unsure. · Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). · Test for correct operation and slide into mounting sleeve to secure. · Snap trim ring into place. · Mount the iplugTM adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8" Phillips head screws. TYPICAL FRONT-LOAD DIN MOUNTING METHOD 4 XDVD8130 INSTALLATION Wiring Diagram - Inputs/Outputs FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDVD8130 uses one 10 amp ATM fuse located beside the wiring connector. 5 XDVD8130 INSTALLATION Wiring Diagram - Power/Speakers Wiring Notes: Connecting the parking brake lead (Yellow/Blue - ) The Yellow/Blue lead MUST be connected for the in-dash monitor to operate properly. The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash DVD video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. This wire must be connected in accordance with all local, state and federal laws in your area. Connecting the reverse lamp lead (White/Brown + ) The White/Brown lead connects to the vehicle reverse lamp circuit (optional). When reverse gear is selected, the unit will automatically switch to V3 mode and display the image on screen. This will allow the driver to view images from a back-up camera (optional) connected to the dedicated V3 camera input. Speaker Connections Do not connect any speaker leads to chassis ground or each other as severe damage will occur. Use 4 ohm speakers with a 60 watt (minimum) power rating only. Fuses When replacing a fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the unit. To prevent accidental shorts, insulate any unused wires. 6 XDVD8130 INSTALLATION Wiring Diagram - Optional A/V Connections The diagram above illustrates the connection capabilities of the XDVD8130. Two separate Audio/Video inputs allow the connection of a DVD player or game console. The video output provides signal to external monitors - such as an overhead or headrest type. A rear view camera can be connected to provide assistance when backing up your vehicle. Visit your local DUAL dealer for more details. * All items shown above are optional and sold separately. 7 XDVD8130 OPERATION Control Locations - Receiver 1 2 3 4 5 6 7 8 9 10 11 12 19 1 2 3 4 5 6 7 8 9 10 18 Open 17 11 12 13 14 15 16 17 18 19 Eject 16 15 14 13 Rotary Volume Reset Power Menu/Audio TFT LCD Band/Play/Pause Mode Tune/Track Down Loudness/Sub On/Off Tune/Track Up Auto Store/Preset Scan Navigation Mode EQ Display Infrared Sensor Tilt Control/Video Mode Mute Caution · Due to its highly technological design, the XDVD8130 faceplate is NOT removable. Do not attempt to remove the faceplate. · This model incorporates a motorized moving monitor. Before final installation, make sure the monitor will not obstruct the dash or shifter. · Upon installation, do not attempt to move the monitor by hand. Use the OPEN button on the faceplate only. 8 XDVD8130 OPERATION Mode Select Control Locations - Remote 2 1 3 21 22 23 4 5 7 9 11 13 15 10 12 14 16 18 24 6 25 8 26 27 28 30 31 32 34 35 37 36 29 33 17 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 XDVD8130 Power DVD Menu Band/Play/Pause 4-Way Up 4-Way Left 4-Way Down Mute Volume Down Stop Tune/Track/Chapter Down Setup Audio Zoom 14 15 16 17 18 19 20 21 22 23 24 25 XNAV9525 Power* Preset #2/System* Preset #1/Escape* Preset #4/Volume Down* Key #8/Function 2* Key #7/Function 1* Slow/Function 4* Mode Tilt Control/Video Mode Enter 4-Way Right Volume Up 26 27 28 29 30 31 32 33 34 35 36 37 Tune/Track/Chapter Up Display Title Subtitle Random Repeat Preset #3/Menu* Preset #5/Mute* Preset #6/Volume Up* Key #9/Function 3* Key #0/Function 5* Angle/Function 6* * Dedicated DUAL XNAV9525 functions 9 XDVD8130 OPERATION General Operation Power On/Off Press PWR or any other button (except EJECT or OPEN) to turn the unit on. Inserting a disc will turn the unit on automatically. Press PWR to turn the unit off. Press RESET the unit upon initial installation or if abnormal operation occurs. Refer to page 8 for the reset button location. Press MODE to select between tuner, DVD player and auxiliary input. Modes of operation are indicated in the display. Press VID to select between OFF, AV1, AV2 and V3 modes. Modes of operation are indicated in the display. The auxiliary A/V inputs can be selected from any mode (except DVD mode). This allows video to be displayed while listening to the AM/FM tuner (only when the vehicle is in Park and the parking brake is applied), for instance. Notes · The vehicle must be in park and the parking brake applied to view video on the in-dash monitor. · As a safety feature, "Picture Off For Your Safety" will appear on the display for 5 seconds anytime the vehicle's parking brake is not engaged. DVD, AV1 and AV2 audio can be heard while the vehicle is in motion. · The video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction. In-dash video functions will only operate when vehicle is in Park and the parking brake is engaged. It is illegal in most states for the driver to view video while the vehicle is in motion. Refer to local laws in your area. The angle of the monitor can be adjusted to provide the best view. To adjust, press TILT for more than 2 seconds. "Tilt Cont" will momentarily appear in the TFT display. Use the rotary encoder or the VOL buttons to adjust the angle. If the tilt is not adjusted for 5 seconds, the unit will return to normal operation. Adjust volume using rotary encoder or the VOL buttons (00-46). Reset Mode Video (AUX) Tilt Control (monitor angle) Volume 10 XDVD8130 OPERATION General Operation Programmable Turn-On Volume Press and hold PWR for 3 seconds to program currently selected volume level. "ON VOL" and the current volume level will momentarily appear in the display. The unit will return to this volume level anytime the unit turned on. Press LOUD to activate and deactivate l ...