MODELS: ASG100, ASG120 OPERATING INSTRUCTIONS Thank you for purchasing an Earlex Electric Airless Spray Gun, this is a highly versatile spray gun and can be used for a variety of applications. Please read all these instructions before operating this product and retain them for future reference. Earlex Ltd will accept no responsibility for the use of this product if used for any other purposes than those detailed herein. SAFETY OPERATING INSTRUCTIONS WARNING: When using the spraygun, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury. G Keep work area clean - Cluttered areas and benches G Never under any circumstances aim the nozzle at invite injuries. G Consider work area environment - Do not expose the another person or animal. In the event of injury occuring seek expert medical advice immediately. G Always keep the spray basket nozzle in place during spray gun to rain. Do not use the spray gun in damp or wet locations. Keep work area well lit. Do not use the spray gun where there is risk to cause fire or explosion. G Guard against electric shock - Avoid body contact with use. Never allow the spray to come in direct contact with the skin. G Always ensure there is adequate ventilation when spraying. G Never spray near a source of ignition, e.g. hot earthed or grounded surfaces (e.g. pipes, radiators, ranges, refrigerators). G Keep children away - Do not let visitors touch the tool surfaces, sparks, cigarettes, glowing wires & open flames including appliance pilot flame. G The spray gun must not be used for spraying or extension cord. All visitors should be kept away from the work area. G Store idle tools - When not in use, tools should be flammable materials below flashpoint 21°C. G Always beware of any hazards presented by the stored in a dry, high or locked place, out of reach of children. G Do not force the tool - it will do the job better and safer at the rate for which it was intended. G Dress properly - do not wear loose clothing or material being sprayed and consult the markings on the container or the information supplied by the manufacturer of the material to be sprayed, including requirements for the use of personal protective equipment. Do not spray any material where the hazard is not known. G G G G G G G jewellery, they can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when G The spray gun must not be cleaned with flammable liquids below flash point 21°C. working outdoors. Wear protective hair covering to contain long hair. G Check for damaged parts - Before further use of the Always wear a mask when spraying. tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for We recommend the use of eye protection to keep alignment of moving parts, free running of moving hazardous vapours out of eyes. parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or We recommend the use of ear protectors. other part that is damaged should be properly Do not abuse the cord - Never carry the tool by the repaired or replaced by an authorized service centre cord or yank it to disconnect it from the socket. Keep unless otherwise indicated in this instruction manual. the cord away from heat, oil and sharp edges. Have defective switches replaced by an authorized service facility. Do not use the tool if the switch does Do not overreach - Keep proper footing and balance not turn it on and off. at all times. G Warning - The use of any accessory or attatchment, other than those recommended in this instruction Always disconnect from mains supply when not in manual, may present a risk of personal injury. use, when refilling the paint container and before cleaning. G Maintain tools with care - Follow instructions for Avoid unintentional starting, do not carry a plugged in lubrication and changing the accessories, inspect tool regularly and if damaged, get repaired by an tool with a finger on the switch and ensure the switch authorized service centre. is off when plugging in. G Have your tool repaired by a qualified person - This G When tool is used outdoors, use extension cords only intended for outdoor use. G It is recommended that a RCD (residual current device) rated at 30mA is fitted into the mains supply socket for added protection against electric shock. G Stay alert - Watch what you are doing. Use common electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user. G Use genuine Earlex parts only. sense and do not operate tool when you are tired. 2 WHAT IS INCLUDED WITH YOUR SPRAY GUN ASG100 & ASG120 kits include: G Spray gun with 1.0mm spray nozzle (yellow) fitted, for spraying woodcare treatments. G Viscosity cup, which enables you to test your paint for thickness before painting. G Flexible Extension (with Swirl head), can be bent up to 45°, to paint horizontal or angled surfaces. G 0.6mm general purpose spray nozzle (black). G Replacement atomiser valve. Atomiser valves wear with use. See `Maintenance and Repair'. Piston Punch, to help free the piston in the unlikely event of a seizure. G Bottle of Lubricating Oil G ASG120 kits also include: G Remote Pick Up system. For larger jobs, paint can be fed directly from a can. See section `Remote Pick Up system'. G 0.8mm spray nozzle (blue) for spraying emulsion and other thick materials. NOISE AND VIBRATION LEVELS The following values were measured in accordance with EN50144. Continuous A-weighted equivalent sound pressure level: 90 dB(A). A-weighted sound power level: 103 dB(A) Vibration level: 12 m/s2 PLEASE NOTE We have done all we can to ensure that used correctly and according to these instructions, the Earlex Electric Airless Spray Gun will give long trouble free service. We accept no responsibility for damage caused by the use of incorrect or unsuitable substances, paint or fluids which have not been thinned correctly or are unsuitable for the surfaces to which they are applied, health hazards arising from lack of ventilation when working in confined spaces, or failure of the equipment due to inadequate cleaning of components after use. If in doubt, always test a small inconspicuous area first. Always read the paint manufacturers instructions first. Neither our guarantee nor the above statement affect your statutory rights. 3 TECHNICAL SPECIFICATION MODEL ASG100 Power Supply Rated Input Container Capacity Spray Gun weight Cable length 230V 50Hz ~ 100 Watts 1.0 Itr 2.0 kg 2 mtr MODEL ASG120 Power Supply Rated Input Container Capacity Spray Gun weight Cable length 230V 50Hz ~ 120 Watts 1.0 Itr 2.0 kg 2 mtr TO OBTAIN THE BEST RESULTS FROM YOUR SPRAY GUN READ THESE INSTRUCTIONS CAREFULLY BEFORE USE. ABOUT THE SPRAY GUN The Spray Gun is a highly versatile electric airless spray gun. It can be used to spray many different materials including varnishes, wood preservatives, enamel paints, oil based paints & water based paints. Airless spraying reduces the mist associated with air spraying & reduces paint loss. The spray gun can be used for a variety of applications including, fences, sheds, boats, furniture, radiators, models & louvre doors. IMPORTANT - SELECTING THE PAINT Many paints & other materials can be sprayed but some cannot. Always check the manufacturer's recommendations before using products with your spray gun. THE SPRAY GUN MUST NOT BE USED FOR SPRAYING EXTERIOR TEXTURED WALL PAINTS OR TEXTURED COATINGS. USING THESE MATERIALS WILL CAUSE PREMATURE WEAR ON THE PISTON & WILL INVALIDATE YOUR GUARANTEE. PREPARING THE PAINT (OR OTHER SPRAY MEDIUM) It is most important to follow the paint manufacturer's recommendations for thinning. Most paints are supplied ready for brush application & must be diluted for use with the spray gun. If you are in any doubt about how much to thin the paint, consult the paint manufacturer. The viscosity cup supplied with your spray gun & the viscosity guide below, can be used to help you determine the correct thickness of the paint. The paint, or paint & thinners mixture, must be thoroughly stirred. We do not recommend the use of an electric stirrer as this can increase the volume of air in the paint, which will reduce the effectiveness of the spray gun. VISCOSITY GUIDE Water based paints Oil Based paints Enamel paints Wood preservatives Primers Varnishes 35-45secs 15-25secs 15-25secs no dilution 20-30secs 20-25secs Aluminium paints Wood stains Latex Emulsions Smooth Masonry Paint (non grit) 15-25secs no dilution *10-20% dilution *5-10% dilution * These paints cannot be measured in the viscosity cup. To spray them, remove the filter from the suction tube, thin according to manufacturer's recommendations and strain to remove any lumps or particles. 4 USING THE VISCOSITY CUP Dip the viscosity cup into the paint (or other medium) to fill it. Time how long the paint takes to empty from the cup (see fig.1) & refer to the viscosity guide on page 4 to compare the time. Thin the paint further until the recommended time is achieved. fig.1 PREPARING & USING YOUR SPRAY GUN SAFETY WARNING! DO NOT SPRAY FLAMMABLE MATERIALS (FLASH POINT < 21°C). ALWAYS SPRAY IN A WELL VENTILATED AREA. NEVER SPRAY NEAR NAKED FLAMES. ALWAYS WEAR PROTECTIVE FACE MASK, GOGGLES, GLOVES & EAR PROTECTORS WHEN USING YOUR SPRAYGUN. MASK THE AREAS OF THE ITEM THAT YOU DO NOT WANT TO SPRAY & PROTECT ANY ADJACENT AREAS THAT COULD BE AFFECTED BY OVERSPRAY. Before fitting the paint container, turn the spray gun upside down & put a few drops of lubricating oil down the inlet and outlet spouts. (see fig.2) Plug the spray gun into a power socket & run the motor for one or two seconds to distribute the oil around the cylinder & piston. Disconnect the power & push the Suction Tube & Filter firmly into the inlet spout, which is the longer of the two spouts. fig.2 Fill the container with the prepared paint or other medium, which as a precaution should be filtered through a suitable funnel that has a filter. As an alternative to a filter the paint can be poured through a nylon stocking or tights. This should ensure there is no contamination of the paint that could block or damage the spray gun. DO NOT FILL THE CONTAINER BEYOND THE MAXIMUM LEVEL INDICATED. Screw the spray gun tightly onto the filled container. Plug the spray gun into a power socket and it is now ready to be set up. 5 SETTING UP THE SPRAY GUN FOR OPTIMUM PERFORMANCE When setting up the spray gun we recommend that you spray the paint MAXIMUM onto some scrap material, newspaper or cardboard. Purge the air from the spray gun by running it for a few seconds until the paint comes out of the gun. The volume of paint & the spray pattern is controlled using the Output Control Knob, (see fig. 3) Turn the knob anti-clockwise to increase the volume of paint sprayed & clockwise to decrease the amount of paint sprayed. A good spray pattern is achieved when there is an even amount of paint in a fine spray throughout the pattern. A poor spray pattern will concentrate the paint in the centre of the spray & give a blotchy finish. To get the best spray performance, turn the Output Control Knob fully anticlockwise. Aim the gun at a piece of cardboard, or similar waste material, & press the switch to start the spray gun. With the spray gun running, turn the Output Control Knob clockwise until the best spray pattern is achieved. If you are unable to achieve an even, fine spray you will probably need to thin the paint further. Follow the thinning procedure as described under "Preparing the Paint". MINIMUM CONTROL KNOB fig.3 SPRAYING TECHNIQUE To obtain best results keep the spray gun level & square on to the surface being sprayed. The gun works best if the nozzle is kept about 25 ­ 30 cms (10" ­ 12") from the surface being sprayed. (See fig. 4) This will result in consistent, even coverage. To avoid overlap of the paint & therefore uneven coverage, we recommend that the spray gun be momentarily turned off whenever you change direction. Move the spray gun at an even speed. A fast speed will give a thin coat & a slow speed will give a thicker coat. Never tilt the spray gun more than 45° as this could result in paint getting in to the motor & causing serious damage. HELPFUL HINTS 1) Only apply one coat at a time. If more than one coat is required follow the paint manufacturers instructions for drying times. fig.4 2) If spraying small objects keep the output setting low as this will avoid excessive use of paint & will minimise overspray. 3) When spraying large areas or objects use a criss-cross pattern either left to right then up & down or vice-versa. Remember to momentarily stop spraying as you change directio ...