User manual EMERSON EWL20S5

Owner's Manual EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A. EWL20S5 20 INCH LCD TELEVISION (Tilt Stand Type) LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: LABOR: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Certain parts and LCD image burn-in are not covered under this warranty. FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase. FEATURES LIMITS AND EXCLUSIONS: This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty. This warranty shall not be extended to any other person or transferee. This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not purchased and used in the United States. This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God. THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS. FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER. THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED. MTS/SAP Tuner 181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels. PLL Frequency Synthesized Tuning- Provides free and easy channel selection and lets you tune directly to any channel using the channel number buttons on the remote control. Sleep Timer Closed Caption Decoder Auto Shut Off Function- If there is no signal input from the antenna terminal and no user operation for 15 minutes, the TV will turn itself off automatically. V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV. Full-Function Remote Control On-Screen Function Display S-VIDEO Input- Allows you to get better picture detail and clarity. Component Input PRECAUTIONS IMPORTANT: THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP. Place your TV in a room with adequate ventilation. Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight. Do not place your TV on soft surfaces, such as rugs or blankets. Leave enough room for air to circulate around the bottom, top and back of the set. ATTENTION: FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE. WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS: To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers without prior written approval. The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Date of Purchase Dealer Purchase from Dealer Address Dealer Phone No. Model No. Serial No. To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please contact us at : FUNAI CORPORATION Customer Service IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER READING OWNER'S MANUAL, PLEASE CALL TOLL FREE 1-800-256-2487 OR VISIT OUR WEB SITE AT http://www.EmersonAudioVideo.com Tel :1-800-256-2487 http://www.EmersonAudioVideo.com 19900 Van Ness Avenue, Torrance, CA 90501 1EMN21873A Printed in China L2621UB/L2601UB* * * * IMPORTANT SAFEGUARDS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. 1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated. 2. RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed. 5. CLEANING - Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6. ATTACHMENTS - Do not use attachments not recommended by the TV manufacturer as they may cause hazards. 7. WATER AND MOISTURE - Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. ACCESSORIES - Do not place this PORTABLE CART WARNING TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, S3126A or table recommended by the manufacturer, or sold with the TV. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. AMEUBLES - Cet appareil ne doit SYMBOLE D'AVERTISSEMENT POUR LES COMPOSANTES être placé que sur un meuble (avec APPAREIL ET MEUBLE A ROULETTES ou sans roulettes) recommandé par le fabricant. Si vous l'installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution. S3126A Un arrêt brusque, l'utilisation d'une force excessive et des surfaces irrégulières risquent de déstabiliser l'ensemble et de le renverser. 9. VENTILATION - Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. POWER SOURCES - This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions. 11. GROUNDING OR POLARIZATION - This TV is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12. POWER-CORD PROTECTION - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A) 14. LIGHTNING - For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges. 15. POWER LINES - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. OVERLOADING - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV. 18. SERVICING - Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the TV. c. If the TV has been exposed to rain or water. d. If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation. e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in performance, this indicates a need for service. 20. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards. 21. SAFETY CHECK - Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition. 22. HEAT - This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) FCC WARNING - This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. S2898A Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. PREPARATION FOR USE CONNECTIONS Plug the incoming cable into the ANT jack on the rear of the TV. Cable TV signal OR Antenna Rear of this TV INITIAL SETUP When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed. The "INITIAL SETUP" menu is displayed every time you turn on the unit unless the scanning is completed. 1 VIDEO2 R AUDIO L COMPONENT Y Pb Incoming cable from home Antenna / Cable Company (No Cable Box) Cable Box or Satellite Box* IN OUT HEAD Pr R AUDIO L VIDEO1 VIDEO S-VIDEO ANT Select the desired language according to the screen indication. After that, the TV performs "AUTO PRESET CH" to scan channels available for the broadcasting in your area. SELECT LANGUAGE ENGLISH ESPAÑOL FRANÇAIS NEXT:PRESS CHK DESPUÉS:PRESIONE CHL APRÈS:PRESSEZ VOLX 2 ­ INITIAL SETUP ­ PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT. THEN PRESS CH K, IN ORDER TO PERFORM "AUTO PRESET CH ". If the TV screen shows snow noise and there is no operation for more than 5 seconds, "HELPFUL HINTS" appears. Follow the instructions listed onscreen. - HELPFUL HINTS 1. PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED. 2. DID YOU PERFORM "AUTO PRESET CH" ? 3. PLEASE REFER TO FRONT PAGE OF THE OWNER'S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION. PHONE OR ANT Incoming cable from Cable Company or Satellite Antenna *NOTE (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company. When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel. Notes: In case no channel can be received by the channel scanning, "NO TV SIGNALS" is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again. If those settings do not work properly, please call our help line on the front page of this owner's manual. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. Note: · For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack before moving the unit. [EXTERNAL CONNECTION] VIDEO1 input VIDEO2 R AUDIO L COMPON Y ENT SELECTING AUDIO/VIDEO INPUT When you use the AUDIO/VIDEO input jacks, select "VIDEO1" or "VIDEO2" mode by pressing [INPUT SELECT] on the remote control or [INPUT SELECT] on the main unit. The input mode changes by pressing the button as following: INPUT SELECT TV channel VIDEO1 VIDEO2 TILT STAND Tilt Stand Adjust the stand to change the angle of TV (-5° ~ 10°). -5° 10° Rear of this TV Pb Pr (OUT) ex. Audio Cable (OUT) Video Cable Video Cassette Recorder (OUT) OR (IN) AUDIO VIDEO2 R R OPERATIONS REMOTE CONTROL AND TOP PANEL FUNCTION IR transmitter To send infrared ray (IR) signal INPUT SELECT AUDIO L COMPONENT Y Pb L Pr (IN) (IN) VIDEO1 VIDEO R AUDIO L VIDEO1 VIDEO S-VIDEO ANT S-VIDEO HEAD PHONE ANT POWER button To turn TV on/off VOL X/ Y buttons To adjust volume To decide the command of settings INPUT SELECT button To select TV or external input CH K/ L buttons To select channels and move up/down through menu items Channel number buttons Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel. +100 button Press to select cable channels higher than 99. SLEEP button To set Sleep Timer CH RET button To return to previous channel POWER o HEA D PHONE CH m VOL p n 2 3 S-Video Cable Notes: The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment. The S-VIDEO jack is given priority over the VIDEO jack. VIDEO2 input ex. (OUT) (IN) VIDEO2 R AUDIO L COMPON ENT 1 4 5 6 7 8 9 Rear of this TV Audio Cable Video Camera Y (IN) Pb Pr MENU button To view on-screen menu MUTE button To mute sound DISPLAY button To display CH No./Audio Status MENU 0 +100 MUTE SLEEP DISPLAY CH RET VIDEO2 R R Note: You can test if the remote control sends out the infrared signal with an AM radio. (Refer to "TROUBLESHOOTING GUIDE".) MENU button To view on-screen menu VOLUME K/ L buttons To adjust volume CHANNEL K/ L buttons To select channels INPUT SELECT button To select TV or external input POWER button To turn TV on/off AUDIO L (OUT) AUDIO L VIDEO1 VIDEO COMPONENT Y Pb Pr R AUDIO L VIDEO1 VIDEO S-VIDEO ANT S-VIDEO HEAD PHONE Video Game Component Video Cable ANT HEAD PHO NE Notes: This TV can accept 480p / 480i / simplified 1080i video signal. Simplified 1080 video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal. MENU VOLUME CHANNEL INPUT SELECT POWER INSTALLING THE BATTERIES MENU VOLUME CHANNEL INPUT SELECT POWER 1 2 3 Install two AAA batteries (supplied) matching the polarity indicated inside battery compartment of the remote control. [BATTERY PRECAUTIONS] · Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device. · Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones. · If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. · Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. POWER Power Indicator Infrared Sensor Window Note: If some digits appear in the corner of the screen when the unit is turned on at the first time, press [POWER] without unplugging the power cord. OPERATIONS (Continued) CHANNEL SETTING [AUTO PRESET CHANNELS] Channel presetting is necessary at the start or in case you moved the TV to a different area. This feature automatically scans and memorizes all available channels in your area and lets you easily select with [CH /]. [ADDING/DELETING CHANNELS] You can add channels that was not memorized by AUTO PRESET CH due to the bad reception status and also delete channels you no longer receive or seldom watch. BRIGHTNESS Adjust until the darkest parts of the picture are as bright as you prefer. [-] : decrease brightness [+] : increase brightness CONTRAST Adjust to increase or decrease contrast. [-] : decrease contrast [+] : increase contrast COLOR Adjust to be brilliant or pale color. [-] : be pale color [+] : be brilliant color TINT Adjust to obtain natural skin tones. [-] : add red [+] : add green SHARPNESS Adjust the detail of the picture. [-] : less clear [+] : more clearer Note: The display will disappear automatically after 10 seconds unless you press any buttons. 1 1 Select "CHANNEL SET UP" MENU - TV SET UP PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE Select "CHANNEL SET UP" MENU - TV SET UP PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE CH CH o p VOL o p VOL m m 2 Select "AUTO PRESET CH" CH - CHANNEL SET UP ADD/DELETE CH (TV) AUTO PRESET CH 2 Select "ADD/DELETE CH" - CHANNEL SET UP - BACK LIGHT SETTING 1 Select "BACK LIGHT" - TV SET UP - o p VOL VOL ADD/DELETE CH (TV) AUTO PRESET CH m 2 Select the desired brightness mode VOL MENU m 3 Select the channel you wish CH 1 2 3 The tuner starts scanning automatically. CH 3 After scanning (completed) The lowest memorized channel appears. OR (in failure) Check antenna connection and try again. 15 o p or 4 5 6 o p PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE m n [BRIGHT] [NORMAL] [DARK] 7 8 9 3 0 +100 To exit the menu MENU 4 Add or delete the channel VOL 15 NO TV SIGNAL m n CLOSED CAPTION ADD/DELETE Note: The TV may recognize TV channels as CATV channels if reception condition is poor. If this happens, check the antenna connections and try scanning again when reception conditions are better. Add: light blue Delete: light red You may view specially labeled (cc) TV programs, movies, news and prerecorded tapes, etc. with either a dialogue caption or text display added to the program. 2 Select the desired caption mode VOL m n 5 To exit the menu MENU 1 Select "CAPTION" MENU - TV SET UP PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE [OFF] [CAPTION1] [CAPTION2] [TEXT2] [TEXT1] SLEEP TIMER SETTING 1 Select "SLEEP" MENU - TV SET UP PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE CH CH o p VOL m n · The time increases by 10 minutes up to 90. Notes: When you disconnect the unit from the AC outlet or when you have a power failure, the sleep time will be lost. To cancel the sleep timer, press [SLEEP] repeatedly until "SLEEP 0 MINUTE" is displayed. The Sleep Timer Setting SLEEP 10 MINUTE display will disappear automatically after 10 seconds of the operation. You can also set the Sleep Timer by pressing [SLEEP] repeatedly. o p 3 To exit the menu MENU MULTI-CHANNEL TELEVISION SOUND (MTS) SYSTEM 1 Select "TV SOUND" MENU - TV SET UP PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE Menu Selection Type of broadcast Regular Stereo broadcast SAP MAIN -NoneSTEREO MAIN MONO -NoneMONO MAIN SAP* -NoneSTEREO SAP CH [CAPTION MODE (CAPTION1, CAPTION2)] CAPTION1 displays standard closed captions (what a character is saying). CAPTION2 displays foreign language closed captions (foreign language words showing what a character is saying). There are three ways of displaying according to programs: Paint-on mode: Displays input characters on the screen immediately. Pop-on mode : Once characters are stored in memory, they are displayed all at once. Roll-up mode : Displays the characters continuously by scrolling (max. 4 lines). [TEXT MODE (TEXT1, TEXT2)] TEXT1 and TEXT2 display half-screen text by scrolling (such as a channel guide, schedule or announcement). Notes: If closed captioning is not broadcasted, you cannot receive it and nothing is displayed. When your TV receives a special effects playback signal (i.e., Search, Slow and Still) from a VCR's video output channel (CH3 or CH4), the TV may not display the correct caption or text. Captions and texts may not match the TV voice exactly. Interference may cause the closed caption system not to function properly. The caption or text characters will not be displayed while the menu display or functions display is shown. If a black box appears on the screen, this means that the TV is set to TEXT mode. To clear screen, select [CAPTION1], [CAPTION2] or [OFF]. o p *Second Audio Program (SAP) : Select the desired sound mode [MONO] [SAP] Your program can also be received in a second language or sometimes a radio station. Note: If you select [SAP] when second audio is not available, the TV will receive normal audio. 2 VOL m n [MAIN] 3 To exit the menu MENU OPTIONAL SETTINGS LANGUAGE SELECTION 1 Select "LANGUAGE" - TV SET UP - PICTURE ADJUSTMENT 1 Select "PICTURE" - TV SET UP - 2 PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE Select an item to adjust CH 2 PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE Select the desired language VOL MENU o p MENU m n VOL [BRIGHTNESS] [CONTRAST] CH [ENGLISH] [ESPAÑOL] m o p [FRANÇAIS] [SHARPNESS] [TINT] [COLOR] 3 3 Adjust the setting VOL To exit the menu MENU m n ... + BRIGHTNESS ... ­ - + OPTIONAL SETTINGS (Continued) V-CHIP SET UP This enables parents to prevent their children from watching inappropriate material on TV. The limitation is not available for news, sports programs, unedited movies on premium cable channels and Emergency Broadcast System signals. When you try to access to a program which is blocked, "PROTECTED PROGRAM by ..." message appears on the TV screen. Programming may be rated by the Motion Picture Association of America (MPAA) or according to the Television Parental Guidelines. In order to block any inappropriate programming, set your limits in both MPAA RATING and TV RATING. Set to [BLOCK] or [VIEW] 6 [BLOCK] [VIEW] [BLOCK] [BLOCK] [BLOCK] To exit the menu MENU A 4 [TV RATING SET UP] Select a rating CH VOL TV-PG BD L S V m B TV-Y TV-Y7 ( TV-G TV-PG ( TV-14 ( TV-MA( ) ) ) ) [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] o p 1 Select "V-CHIP SET UP" MENU - TV SET UP PICTURE CHANNEL SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] TV SOUND [MAIN] BACK LIGHT [BRIGHT] SLEEP [0] MINUTE · TV-Y : Appropriate for all children · TV-Y7 : Appropriate for children seven and older · TV-G : General Audience · TV-PG : Parental Guidance suggested · TV-14 : Unsuitable for children under 14 · TV-MA : Mature audience only · TV-Y7 FV : Fantasy Violence · TV-PG / TV-14 / TV-MA : D: Suggestive Dialog (TV-PG, TV-14 only) L: Coarse Language S: Sexual Situation V: Violence Notes (for TV RATING and MPAA RATING): You cannot access the setup menu when the "PROTECTED PROGRAM by ..." message appears. Move to an unblocked channel before you press [MENU]. When you select a rating and set it to [BLOCK], the higher ratings will be blocked automatically. The lower ratings will be available for viewing. When you set the lowest rating to [VIEW], all other ratings will automatically be available for viewing. 6 To exit the menu MENU C 4 [CHANGING THE ACCESS CODE] Enter 4-digit code 1 2 3 5-1 CH * Rating with no sub categories Set to [BLOCK] or [VIEW] VOL TV-Y TV-Y7 ( ) B TV-G TV-PG (DLSV) TV-14 (DLSV) TV-MA( LSV) [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] [BLOCK] NEW CODE o p VOL B 4 4 5 6 [[[[ CONFIRM CODE [MPAA RATING SET UP] 7 8 9 Select a rating CH ____ 0 m m o p BG PG PG-13 R NC-17 X [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] 5 To exit the menu MENU 2 Enter 4-digit code 1 2 3 5-2 ACCESS CODE * Rating with sub categories VOL 5 [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] [VIEW] Set to [BLOCK] or [VIEW] VOL 4 5 6 ____ 7 8 9 m 0