User manual EMERSON EWV603

EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A. RF Output Channel If channel 3 is already occupied for broadcasting, Hint 1) Set your TV to channel 4. · The RF output channel may 2) Insert a pre-recorded tape into the VCR. not change when you adjust 3) Press the PLAY button once. tracking during playback. In 4) After a few seconds, press the PLAY button on the VCR for 3 seconds. this case, stop the playback, · The RF output channel will change to channel 4 from channel 3 and you will and start the playback again. After that, press the PLAY see a playback picture. button on the VCR for 3 sec· When a picture does not appear on the TV screen, repeat step [4]. onds again. 5) Press the STOP button to stop playback. Owner's Manual Video Cassette Recorder If you need additional operating assistance after reading this owner's manual or to order replacement accessories, please call TOLL FREE : 1-800-256-2487 or visit our web site at http://www.funai-corp.com EWV603 Basic VCR/TV Connection Cable Signal or Antenna (Back of TV) Cable Signal or 1. Before using your VCR Antenna (Back of VCR) (Back of TV) ANT IN Stereo TV Connection You can use the AUDIO OUT jacks and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. In this case, you need to set the TV to external Line Input Mode. Please refer to your TV's owner's manual. VIDEO IN AUDIO IN L R AUDIO L OUT R VIDEO IN ANT IN OUT OUT IN Audio/Video Cables (not supplied) ANT IN VIDEO OUT AUDIO OUT Disconnect 2 Connect OUT 3 Connect (supplied) L R (Back of TV) Connect 1 OUT (Back of VCR) RF Cable Front & Rear Terminals AUDIO OUT jacks Connect the audio cables to the audio in jacks of a camcorder, another VCR, a stereo amplifier, or an audio system. AUDIO L AUDIO L ANT IN 4 Plug the AC power cords of the VCR and TV into the AC outlets. Hint for Cable Box or Satellite Box Connection A Cable Signal (Cable box or Satellite box) IN OUT AUDIO IN jacks Connect the audio cables from the audio out jacks of a camcorder, another VCR, or an audio source. ANT IN OUT R IN (Back of VCR) ANT IN Connection B ANT IN (Back of VCR) OUT OUT RF Cable (supplied) E Cable Signal (Cable box or Satellite box) IN OUT ANT IN jack Connect your antenna or cable box. ANT OUT jack Connect the RF cable (supplied) to the antenna input jack on your TV. E OUT R IN VIDEO OUT (Back of TV) RF Cable (supplied) RF Cable (Back of TV) OUT IN VIDEO OUT OUT IN Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the VCR. You can view or record ONLY the channels you have selected on the cable box or the satellite box. · While you are recording, only the recorded channel can be viewed. To select channels of the cable box or satellite box 1)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button.The POWER and the VCR/TV indicators on the front panel will light on. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box). · If you use the channel 4, you need to change the VCR's RF output to channel 4. Refer to "RF Output Channel". 2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1). 3) At the cable box or satellite box, select the channel you want to view or record. Select this connection when you want to change channels on the VCR. With this connection, you may watch one channel while recording another. · You may not view or record a scrambled channel. To select channels of the cable box or satellite box 1)At the cable box or satellite box, select channel 3 or 4 (the same channel as the VCR's RF output channel.) · Refer to "RF Output Channel". 2)At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box. 3)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button .The POWER and VCR/TV indicators on the front panel will light on. Then, select the channel you want to view or record. To play back a tape Follow the steps 1) to 2) above. Then, play back a tape. · Refer to "Playback" on page 5. To view one channel while recording another 1)While you are recording on the VCR, press the VCR/TV button so that the VCR/TV indicator disappears on the VCR. 2)At the cable box or satellite box, select the channel you want to view. - VIDEO OUT jack Connect the video cable to the video in jack of a camcorder, another VCR, or a TV. POWER CHANNEL VIDEO L-AUDIO-R POWER VCR/TV TAPE IN TIMER REC MENU REC/ VIDEO IN jack Connect the video cable from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.). Supplied Accessory · Remote control (NA372UD) with Two AA batteries · RF Cable · Owner's Manual (WPZ0901TM002) (0VMN03902) Installing the Batteries for the Remote Control Install two AA batteries (supplied) matching the polarity indicated on the bottom of the remote control. 1- Printed in China 0VMN03902 / HF440UD 2. Important Safeguards WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. 1. Read Instructions- All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions- The safety and operating instructions should be retained for future reference. 3. Heed Warnings- All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions- All operating and use instructions should be followed. 5. Cleaning- Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6. Attachments- Do not use attachments not recommended by the video product manufacturer as they may cause hazards. 7. Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. Accessories- Do not place this video product on an unstable cart, stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9. Ventilation- Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to . 10. Power Sources- This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 11. Grounding or Polarization- This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12. Power Cord Protection- Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. Outdoor Antenna Grounding- If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A) FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMP NEC ­ NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) S2898A 14. Lightning- For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges. 15. Power Lines- An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. Overloading- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 17. Object and Liquid Entry- Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product. 18. Servicing- Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. Damage Requiring Service- Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or damaged in any way. f. When the video product exhibits a distinct change in performance-this indicates a need for service. 20. Replacement Parts- When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 21. Safety Check- Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 22. Heat- This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. -2- EN 3. Preset for Use Turn on the VCR for the first time To Add/Delete Channels Clock Set Up 1 Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see"RF Output Channel" section. To Select a Channel You can select a channel by directly pressing the Number buttons on the remote control. Notes for using the Number buttons: · When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7) · You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). 1 MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUDIO OUT TV STEREO [ON] SAP 1 MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT AUDIO OUT TV STEREO [ON] SAP 5 STOP PLAY CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : ­­ AM/PM ­­ or STOP PLAY STOP PLAY or or 2 POWER Remote Control TV Screen F.FWD LANGUAGE SELECT B ENGLISH STOP PLAY · If the clock is not set, the CLOCK SET screen appears when you press the MENU button. In this case, go to step [2]. F.FWD Select the current hour F.FWD [ON] 6 STOP PLAY CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : 40 AM/PM ­­ FRANCAIS ESPAÑOL 2 STOP PLAY CHANNEL SET UP AUTO SET UP B MANUAL SET UP or or To Preset the Channel Again 1) Press the MENU button until the main menu appears. 2) Select "CHANNEL SET UP" by pressing the PLAY or STOP button. Then, press the F.FWD button. 3) Select "AUTO SET UP" by pressing the PLAY or STOP button. Then, press the F.FWD button. After scanning, the tuner stops on the lowest memorized channel. 2 STOP PLAY CLOCK SET MONTH DAY 03 / ­­ HOUR MINUTE ­­ : ­­ YEAR ­­­­ AM/PM ­­ or or F.FWD Select the current minute F.FWD F.FWD Select the current month F.FWD 3 F.FWD CH 01 7 STOP PLAY CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : 40 AM/PM P M AM B PM AUTO SET UP 3 STOP PLAY MANUAL SET UP CHANNEL 30 ADD or (CATV) 3 STOP PLAY CLOCK SET MONTH DAY 03 / 15 HOUR MINUTE ­­ : ­­ YEAR ­­­­ AM/PM ­­ or To Change the On-Screen Language Do you connect the cable of the cable box or the satellite box to the VCR's ANT IN jack? Yes 1) Press the MENU button until the main menu appears. 2) Select "LANGUAGE SELECT" by pressing the PLAY or STOP button. Then, press the F.FWD button. 3) Select "ENGLISH" , "FRANCAIS" or "ESPAÑOL" by pressing the PLAY or STOP button. Then, press the C.RESET/EXIT button. or Select "AM" or "PM" Yes Press the MENU button to exit · Refer to "Hint for Cable Box or Satellite Box" section on page 1. No Select the channel to be added or deleted. Select the current day F.FWD 8 4 REW F.FWD MANUAL SET UP CHANNEL 30 or ADD (CATV) To exit the CLOCK SET screen. F.FWD No Please wait for a few minutes. After scanning... · The tuner stops on the lowest memorized channel. · You can select only the channels memorized in VCR by using the CHANNEL buttons. · If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press the F.FWD button once again. 4 STOP PLAY CLOCK SET MONTH DAY 03 / 15 HOUR MINUTE ­­ : ­­ YEAR 2004 AM/PM ­­ or Hint · To go back one step, press the REW button (during the steps [2] to [7].) · Your clock setting will be lost if there is a power failure or if the VCR has been unplugged for more than 30 seconds. Hint · If you accidentally select Spanish or French and need English: Press the MENU button and choose SELEC. IDIOMA, or SELECTION LANGUE. Press the F.FWD button, and select ENGLISH. Finally, press the C.RESET/EXIT button. Select "ADD" or "DELETE" Select the current year F.FWD Hint · Repeat these steps only if there was a power failure or if the VCR has been unplugged for more than 30 seconds. 5 To exit the menu. -3- C.RESET EXIT EN 4. Precautions Precautions Install Location For safety and optimum performance of your VCR: · Install the VCR in a horizontal and stable position. Do not place anything directly on top of the VCR. Do not place the VCR directly on top of the TV. · Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the VCR. Avoid locations subject to strong vibration or strong magnetic fields. Important Copyright Information Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright laws. We assume no responsibility for the unauthorized duplication, use, or other acts which infringe upon the rights of copyright owners. Troubleshooting Guide If you are having problems operating your product even though you have followed the instructions in this manual, check the following list of problems and corrective actions. You may be able to solve the problem yourself. PROBLEM No power. Timer recording is impossible. CORRECTIVE ACTION · Make sure the power plug is connected to an AC outlet. · Make sure the power is turned on. · Make sure the timer recording is set correctly. · Make sure the power is off. · Make sure the VCR clock is set correctly. · Make sure the tape has a record tab. If needed, cover the hole with cellophane tape. A Note about Recycling This product's packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away Avoid the Hazards of Electrical Shock and or incinerated but disposed of in accorFire dance with your local regulations con· Do not handle the power cord with wet cerning chemical wastes. hands. · Do not pull on the power cord when Note to the Cable TV System Installer disconnecting it from AC wall outlet. This reminder is provided to call the Grasp it by the plug. Cable TV system installer's attention to Article 820-40 of the National Electrical Moisture Condensation Warning Code, which provides guidelines for Moisture condensation may occur inside proper grounding ­ in particular, specifythe unit when it is moved from a cold ing that the cable ground shall be conplace to a warm place, or after heating a nected to the grounding system of the cold room or under conditions of high building, as close to the point of cable humidity. Do not use the VCR at least for entry as possible. 2 hours until its inside is dry. CAUTION: FCC Warning TO PREVENT ELECTRIC SHOCK, This equipment may generate or use MATCH WIDE BLADE OF PLUG TO radio frequency energy. Changes or WIDE SLOT, FULLY INSERT. modifications to this equipment may ATTENTION: cause harmful interference unless the POUR ÉVITER LES CHOC modifications are expressly approved in ÉLECTRIQUES, INTRODUIRE LA the instruction manual. The user could LAME LA PLUS LARGE DE LA lose the authority to operate this equipFICHE DANS LA BORNE CORREment if an unauthorized change or modi- SPONDANTE DE LA PRISE ET fication is made. POUSSER JUSQU'AU FOND. Cannot go into Recording mode. Playback picture is partially noisy. · Adjust tracking control for a better picture by pressing the CHANNEL buttons. No playback picture (only sound can be heard.) No or poor playback picture. · Head cleaning may be necessary. Refer to "Auto Head Cleaning" on page 8. · Make sure the VCR is not in the Menu mode. · Turn on the TV and set the TV to channel 3. If channel 3 is already occupied for broadcasting, change the RF output to channel 4, and change the TV channel to channel 4. (See "RF Output Channel" on page 1 for the detail.) · Fine tune the channel reception on your TV. TV programs cannot be seen nor- · Re-check the ANT. IN and ANT. OUT connections. See page 1. mally. · Press the VCR/TV button on the remote control so that the VCR/TV indicator on the VCR disappears. No VCR operation from the infrared Remote Control. · Make sure the power plug is connected to an AC outlet. · Check batteries in remote control. Video or color fades in and out when · You cannot copy a copyrighted video tape. You are experiencing copy making a copy of a video tape. guard protection. Specifications Video Heads : Four Heads Power requirement : Operating temperature : 41°F~104°F Power consumption : (5°C~40°C) Dimensions : Converter output : VHF Channel 3 or 4. Weight : 120V, 60Hz 14 Watts W 14-3/16" (360mm) H 3-5/8" (92mm) D 8-9/16" (216mm) 4.0 lbs. (1.8 Kg.) (approx.) · Designs and specifications are subject to change without notice and legal obligation. · If an explanation in the Owner's Manual is not consistent across languages, please refer to the English version. -4- EN 5. Playback Before: Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see "RF Output Channel" section. 7. Other Operations 1 POWER To cue or review picture during playback (Picture Search) Press the F.FWD or REW button. · Press it again and the VCR will now search in super high speed. (in the LP/SLP modes only) MENU REC/OTR STOP /EJEC T To play back in slow motion Press the SLOW button during playback or the still mode. · If the noise bar appears on the TV screen, you can reduce it by pressing the CHANNEL buttons. 4 EJECT VCR /TV 1 4 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL 1 2 PLAY Remote Control TV Screen 7 MENU SEARCH -MODE REW PLAY F.FWD C.RESET EXIT POWER VCR/TV TAPE IN TIMER REC PLAYB POWER VCR/TV TAPE IN REC/OTR DISPLAY PAUSE /STILL To freeze the picture on TV screen during playback (Still mode) Press the PAUSE/STILL button. Each time you press the button, the picture will be forwarded by one frame. · If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing the CHANNEL buttons. · If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if equipped. To temporarily stop recording (Pause mode) Press the PAUSE/STILL button. · During the rec pause mode, five C marks appear on the TV screen. Each C mark represents one minute. · Press it again to resume recording. REW STOP PLAY F.FWD 3 STOP 4 EJECT STOP 3 Hint EJECT A 2 3 4 2 · When a tape without record tab is inserted, the VCR will start playback automatically at step [1]. · Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press the CHANNEL buttons. Auto Rewind When a tape reaches its end during playback, fast-forward, or recording (except timer recording and One Touch Recording), the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and turn itself to off. Counter Reset Press the C.RESET/EXIT button. 6. Recording & OTR (One Touch Recording) Before: Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see "RF Output Channel" section. Hint 2 6 EJECT VCR /TV 2 POWER 1 4 · Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the video head. · To return to playback from the Picture Search/Still/Slow mode, press the PLAY button. 1 with tab 2 1 4 7 2 5 8 0 Remote Control TV Screen 8. On-Screen Operations 1 R CHANNEL MENU REC/OTR 1 4 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL 3 6 9 CHANNEL To call up the main menu MENU CH12 7 MENU SEARCH -MODE C.RESET EXIT T P/EJEC STO REW PLAY F.FWD -MENUB TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT POWER VCR/TV TAPE IN TIMER REC POWER VCR/TV TAPE IN · Select the desired channel · Select the desired tape speed Recording/Playback Time T60 1hour 3hour T120 2hours 6hour T160 2-2/3hours 8hour POWER VCR/TV TAPE IN TIMER REC 3 SPEED SP Tape Speed Type of tape SP mode SLP mode 4 3 5 REC/OTR DISPLAY PAUSE /STILL REW STOP PLAY F.FWD 5 6 MENU REC/OTR STO T P/EJEC REW PLAY F.FWD 2 STOP To select an item PLAY -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT or 4 REC/OTR Accidental erasure prevention REC REC 1 4 23 You can select a fixed recording time by pressing the REC/OTR button repeatedly. REC (Normal recording) OTR(8:00) OTR(0:30) OTR(1:00)..... OTR(7:30) To prevent accidental recording on a recorded cassette, remove its record tab. To record on it later, cover the hole with cellophane tape. 3 Record tab To decide F.FWD POWER EJECT VCR/ TV CHANNEL SET UP AUTO SET UP B MANUAL SET UP 1 4 7 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL SEARCH -MODE C.RESET EXIT 5 STOP STOP 6 EJECT EJECT A Hint · If you have connected the VCR to a cable box or satellite box, refer to "Hint for Cable Box or Satellite Box" section on page 1. 4 To exit the menu C.RESET EXIT 41 2 MENU REC/OTR DISPLAY PAUSE /STILL 4 3 EN MENU REW STOP PLAY F.FWD -5- OR 9. Recording Features Timer Recording ·Insert a tape with its record tab into the VCR. Hint for Timer Recording 1 MENU -MENUB TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUDIO OUT TV STEREO [ON] SAP F.FWD 5 Select the desired start time (hour) STOP PLAY 9 STOP PLAY ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 0 5 / 0 3 MON START TIME 0 7 : 3 0 PM END TIME 0 8 : 3 0 PM CHANNEL 16 REC SPEED SP B SP SLP ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 0 5 / 0 3 MON START TIME 0 7 : 3 0 ­ ­ END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ or or F.FWD Select the desired recording speed C.RESET EXIT · If there is a power failure or the VCR has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost. · If the tape runs out before the end time, the VCR will switch to the Stop mode immediately, eject the tape and the VCR power will be turned off. The TIMER indicator will flash. · If a tape is not in the VCR or does not have the record tab, the TIMER indicator flashes and timer recording cannot be performed. Please insert a recordable tape. · When all the Timer Recording are completed, the TIMER indicator flashes. To play or eject the recorded tape, press the POWER button first, and then press the PLAY or EJECT button. Select the minute To cancel a Timer Recording that is in progress Press the STOP/EJECT button on the VCR. POWER 2 STOP PLAY STOP PLAY or PROGRAM NUMBER 4 DATE ­­/­­ START TIME ­ ­ : ­ ­ ­ ­ END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ or 10 Turn off the VCR for recording F.FWD Copying a Video Tape Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. (Back of TV) (Back of Playing VCR) (Back of Recording VCR*) · TIMER indicator on the VCR lights up. Select an empty program number F.FWD Hint 6 STOP PLAY ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 0 5 / 0 3 MON START TIME 0 7 : 3 0 PM END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ AM B PM · To go back one step, press the REW button (during the steps [3] to [9].) AUDIO AUDIO L L OUT OUT R R VIDEO VIDEO OUT OUT IN IN IN IN ANT