Crux_View Test Program Manual (version 1.6.3) EMTAC Technology Corp. NOTE · · · · · This Crux_View Test Program is a trial version program and only for testing purpose. This Crux_View program is only for use with CRUX II / BTGPS and Pocket PC (PPC) with Bluetooth enabled. Current version of CRUX_View supports ARM (Strong ARM/X Scale) based PPC. Read and consult CRUX II / BTGPS User Guide before operating the CRUX_View program. The Bluetooth trademarks are owned by Bluetooth SIG, Inc. USA and licensed to EMTAC Technology Corp. Copyright 2002 EMTAC Technology Corp. All other company names, trade marks and tradenames are belonged to respective corporation. Crux_View Test Program 1. Installation 1.1 Connect the PPC to the Host PC then `Active Sync' them. 1.2 Open `My Computer' 'Mobile Device' 'My Pocket PC', Copy Crux_View.exe to `\Windows\Start Menu' of the PPC. 1.3 Disconnect the PPC to the Host PC. 1.4 From PPC `Start' menu, Click `Crux_View' to execute it. 2. Operation 2.1 Turn-On the power of BTGPS. 2.2 Pair and Connect the BTGPS with the PPC, if you did NOT have done this before. (Please refer to Pairing Manual of the BTGPS). 2.3 Execute `Crux_View' from `Start' menu on PPC. 2.4 Click `Accept' to continue, if you accept the claim. 2.5 Set `COM' to `COM8' for iPAQ 3870/3975; `COM4' for the PPC that with Socket's BT card. For other PPC and BT card, please refer to the BT card's manual. 2.6. Set the `Baud' to `38400' bps. 2.7 Click `Open' to connect to the BTGPS. 2.8 The GPS Status Page. Indicator and Function Buttons: Fix: The fix status, None, 2D or 3D; plus DGPS. Reset: Cold Start the BTGPS Open: Connect BTGPS. Close: Disconnect BTGPS. Exit: Exit this program. View SV: The No. of the Satellite Visible. 12-Channel Signal-Level View: The Signal Level in dB-Hz of each GPS channel. 2.9 The Position Page. Indicators: Position: The Latitude and Longitude. GPS time: UTC Date and Time. DOP & Speed: Fix: The Fix Status, None, 2D or 3D; plus DGPS. PDOP: Position Dilution of Precision. HDOP: Horizontal Dilution of Precision. VDOP: Vertical Dilution of Precision. The `Unit' of the `Speed' can be select either in `knots' or `km/hr'. 2.10 The Protocol Page. Set NMEA Update Rate: Click this button will send the NMEA update rate setting commands to BTGPS. The new update rate settings (seconds per message) were selected in left side pull down menus before click the `Set NMEA Update Rate' button. Switch to SiRF Binary Protocol 38400 bps: Click this button will switch the BTGPS to SiRF binary protocol in 3800 bps baud rate. Command Status: Indicate the status of sending commands. 2.11 The Message Page. In this page the window display the NMEA messages that coming from BTGPS. Function Buttons: Run: Run displaying. Stop: Stop displaying. 2.12 The ABAS Page. SBAS Channel setting. OFF: Do NOT use SBAS channel. AUTO: BTGPS auto searching available SBAS satellite and use it for correction. PRN120(EGNOS): Use PRN120 only. PRN131(EGNOS): Use PRN131 only. PRN122(WAAS): Use PRN122 only. PRN134(WAAS): Use PRN134 only. Manual Set: Key in PRN No. that desired to be used only. After set the SBAS Channel, Click the `Apply' button to send the command to the BTGPS. SBAS Setting: Show the current SBAS Channel setting of the BTGPS. Command Status: Shows the Command Proceed. 2.13 The LowPower Page Mode: You may set the Low power mode by select the Continuous/TricklePower Mode and setting the desired Update rate/On Time. After changed the Power Mode, Click the `Apply' button to send the command to the BTGPS. Trickle Power Status: Display current power mode setting. 2.14 The About Page. This page shows the software version and copyright claim. ...