User manual ERICSSON GF768

User's Manual English Start here... Read the Safety Instructions _______________ (page i) Insert the SIM Card _______________________ (page 1) Charge the Battery _______________________ (page 2) Attach the Battery ________________________ (page 2) Turn on the Phone _______________________ (page 3) Make a Call ______________________________ (page 6) Answer a Call ____________________________ (page 6) ...and keep going... EN The symbol on our products signifies that they have been certified according to the EMC directive 89/336/EEC, the Telecommunications directive 91/263/EEC, and the Low Voltage directive 73/23/EEC when applicable. The products fulfil the requirements according to the following standards: Cellular Phones and Accessories in Combination: ETS 300 342-1 EMC for European digital cellular telecommunications. Accessories Without Direct Connection to a Cellular Phone: EN 50081 Electromagnetic compatibility, Generic Emission Standard, and EN 50082 Electromagnetic compatibility, Generic Immunity Standard. This manual describes Ericsson GF768 First edition (March 1997) This manual is published by Ericsson Mobile Communications AB, without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Ericsson Mobile Communications AB at any time and without notice. Such changes will, however, be incorporated into new editions of this manual. All rights reserved. © Ericsson Mobile Communications AB, 1997. Publication number: LZT 126 1343/1 R1A Printed in Sweden INNOVATRON PATENTS Important: Read this information before using your portable phone General Since its introduction in the mid 1980s the portable phone is one of the most exciting and innovative products ever developed. With it, you can stay in contact with your office, your home, emergency services, and others. Your telephone is a radio transmitter and receiver. When it is ON it receives and also sends out radio frequency (RF) energy. Depending upon the type of mobile phone you have purchased, it operates in different frequency ranges and employs commonly used modulation techniques. When you use your phone, the system handling your call controls the power level at which your phone transmits. For the safe and efficient operation of your phone, observe these guidelines. · ANSI/IEEE C95.1-1992 (USA, Asia- Pacific) If you want to limit RF exposure even further, you may choose to control the duration of your calls and operate your phone in the most power efficient manner. Do not use an antenna designed for any other type of portable telephone than the telephone you have purchased. Driving Check the laws and regulations on the use of telephones in the areas where you drive. Always obey them. Also, when using your phone while driving, please: Efficient phone operation How to use your phone for optimum performance with minimum power consumption: · Hold the phone as you would any other telephone. While speaking directly into the mouthpiece, angle the antenna in a direction up and over your shoulder. If the antenna is extendable, it should be extended during a call. · Give full attention to driving. · Use hands-free operation, if available. · Pull off the road and park before making or answering a call if driving conditions so require. RF energy may affect some electronic systems in motor vehicles. In addition, some vehicle manufacturers forbid the use of mobile phones in their vehicles. Check with your vehicle manufacturer's representative to be sure your phone will not affect the electronic systems of your vehicle. · Do not hold the antenna when the phone is IN USE. Holding the antenna affects call quality, may cause the phone to operate at a higher power level than needed and shorten talk and standby times. Exposure to radio frequency energy The International Commission on Non-Ionizing Radiation Protection (ICNIRP), sponsored by the World Health Organization (WHO), published a statement in 1996 which sets limits for exposure to RF fields from handheld mobile phone. According to this statement, which is based on the available body of research, there is no evidence that mobile terminals meeting the recommended limits can cause any adverse health effects. All Ericsson telephones conform to the ICNIRP recommendations, and international exposure standards, such as: Antenna care and replacement Do not use the phone with a damaged antenna. Replace a damaged antenna immediately. Consult your manual to see if you may change the antenna yourself. If so, use only an Ericsson approved antenna. Otherwise, take your phone to a qualified service centre for repair. Use only the designated Ericsson antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate the appropriate regulations. Electronic devices Most modern electronic equipment, for example, equipment in hospitals and cars, is shielded from RF energy. However, RF energy from telephones may affect some electronic equipment. Turn your phone OFF in health care facilities when regulations posted in the areas instruct you to do so. Always request permission before using your phone near medical equipment. · CENELEC European Pre-standard ENV50166-2 LZT 126 1343/1 R1A i EN Guidelines for Safe and Efficient Use Mobile telephones may affect the operation of some implanted cardiac pacemakers, equipment for people with hearing impairments and other medically implanted equipment. Pacemaker patients should be aware that the use of a mobile phone very close to a pacemaker may cause the device to malfunction. Avoid placing the phone over the pacemaker, i.e. in your breast pocket. When using the phone, place it at your ear opposite the pacemaker. If a distance of 15cm. is kept between the phone and the pacemaker, the risk of interference is limited. Contact your cardiologist for more information. · To reduce risk of electric shock, unplug unit from power source before attempting any cleaning, then use soft cloth dampened on with water. Product care · Do Not expose product to water or moisture. Example: bathtub, laundry sink, wet/damp basement, swimming pools, etc. Children Do not allow children to play with your phone. It is not a toy. Children could hurt themselves or others (by poking themselves or others in the eye with the antenna for example). Children could also damage the phone or make calls that increase your telephone bills. · Do Not expose product to extreme temperatures such as found near a hot radiator or stove, or in a car parked in the sun. · Do not expose product to extreme cold temperatures such as a car parked outdoors in winter. Blasting areas To avoid interfering with blasting operations, turn your unit OFF when in a "blasting area" or in areas posted "turn off two-way radio". Construction crews often use remote control RF devices to set off explosives. · Do Not expose product to lit candles, cigarettes, cigars, open flames, etc. Aircraft Turn your phone OFF before boarding any aircraft. · Use only Ericsson Original accessories. Failure to do so may result in loss of performance, fire, electric shock, or injury, and will void the warranty. · Use it on the ground only with crew permission · Turn off your phone before the aircraft leaves the ground. Do not use it in the air. To prevent possible interference with aircraft systems, safety regulations require you to have permission from a crew member to use your phone while the plane is on the ground. To prevent interference with communication systems, you must not use your phone while the plane is in the air. Potentially explosive atmospheres Turn your phone OFF when in any area with a potentially explosive atmosphere. It is rare, but your phone or its accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fuelling areas, such as gas stations, below deck on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Do not transport or store flammable gas, liquid, or explosives in the compartment of your vehicle which contains your phone and accessories. · Do Not attempt to disassemble the product. Doing so will void warranty. This product does not contain consumer serviceable components. Service should only be performed by Authorized Service Centres. Power Supply · Connect AC (Power supply) only to designated power sources as marked on the product. · To reduce risk of damage to electric cord, remove from outlet by holding onto AC adapter rather than cord. · Make sure the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress. ii LZT 126 1343/1 R1A Guidelines for Safe and Efficient Use Assembly Instructions Assemble and Charge ­ Four Steps 1. Inserting SIM Card 2. Attaching Battery 3. Connecting Charger to Phone 4. Connecting Charger to Mains About the Charging Function About the Battery and the SIM Card i 1 1 1 2 2 2 3 3 Useful Information while Talking Changing Volume while Talking Muting Microphone Using Phone as Scratch Pad Sending Tone Signals Checking Time of Calls 8 8 8 8 8 8 Setting Alarm Turning Off the Alarm About Display Language Changing Key Sound 14 14 14 14 Making Your Personal Ring Signal About the Phone's Note System Simple Melody Complex Melody 15 15 15 16 Navigating the Menu System About the Menu System Moving Through the Menu System Selecting the Key Sound Menu 9 9 9 9 Diverting Calls About Diverting Calls Diverting Viewing Status of Call Divert Cancelling Call Divert 17 17 17 17 17 Turning On the Phone and General Information Turning On the Phone About the Display Learning about Your Phone 3 3 4 5 Creating Your Own Phone Book About the Phone Book Storing Numbers on SIM Card Storing Numbers in Phone's Memory About Recalling Phone Numbers Position Recall Deleting Storage Position About Last Dialled Numbers About Unanswered Calls 11 11 11 11 12 12 12 13 13 Protecting Your Keypad, Phone and SIM Card About Locks Keypad Lock Card Lock (SIM) Changing PIN Unblocking with PUK Phone Lock (Un)Locking Phone 18 18 18 18 18 18 19 19 Making and Receiving Calls Making a Call Ending a Call Making an International Call Making an Emergency Call Retry Function Receiving a Call Answering a Call Rejecting a Call Putting a Call on Hold About Calling Line Identification (CLI) Handling Two Calls LZT 126 1343/1 R1A 6 6 6 6 6 6 6 6 6 7 7 7 Personalizing Your Phone Changing Ring Volume About Ring Type Viewing the Clock Setting Clock 13 13 13 14 14 Barring Calls ­ Restricting Calls About Barring Calls Activating Call Bars for Any Call Type Cancelling All Call Bars 19 19 20 20 iii EN Table of Contents Sending and Receiving Text Messages About Text Messages Checking Subscription Setting Service Center Address Sending SMS About Other Message Types Receiving a Message Reading an Old Message 21 21 21 21 21 22 22 22 Receiving Area Information About Area Information Activating the Area Information Adding a Code Erasing a Code Changing a Code 23 23 23 23 23 23 Knowing Duration of Calls About Duration of Calls Viewing Calling Information 24 24 24 Other Networks About Choosing Network Selecting a Network 24 24 25 Index 27 iv LZT 126 1343/1 R1A This chapter describes how you assemble the phone, what the SIM Card is, and how you handle the battery. Assemble and Charge ­ Four Steps q q 1. Inserting SIM Card Place the SIM Card with the golden connectors facing down and the cut corner turned to the left (see Figure 1). Slide the SIM Card into the SIM Card slot. The SIM release button will slide towards the antenna as the SIM Card is pushed in. 1. Removing SIM Card 1. Make sure the battery is removed. 2. Slide the SIM release button towards you (see Figure 2). 3. Pull out the SIM Card. Insert the SIM Card. Attach the battery. Connect the charger to the phone. Connect the charger to the mains. q q 1. 2. 2. Figure 1. Inserting SIM Card LZT 126 1343/1 R1A Figure 2. Removing SIM Card. 1 EN Assembly Instructions 2. Attaching Battery Place the battery on top of the phone and push until you hear a click (see Figure 3). Removing Battery 1. Make sure the phone is turned off. 2. Press the locking catch on the bottom of the battery (see Figure 4.). 3. Lift the battery up and away from the phone. 1. Disconnecting Charger Lift the plug up and pull it out (see Figure 5). 1. To mains 2. 2. Figure 3. Attaching battery. Figure 4. Removing battery. Figure 5. Connecting and disconnecting charger. 3. Connecting Charger to Phone Have the battery attached to the phone and connect the charger as described in Figure 5. Use the power plug that fits your mains. 2 4. Connecting Charger to Mains Plug the charger into a mains socket. The phone now starts to charge the battery and you can see the battery meter in the display move while charging. LZT 126 1343/1 R1A When you connect external power to the phone, the battery is charged. When the battery is fully charged, the charging stops. You cannot overcharge your battery. When you are charging the battery you can use your phone as normal; however the charging time will be longer. The Battery Your phone is supplied with a Nickel Metal Hydride battery. The battery is not charged before shipment, even though there might be enough power to turn the phone on. The SIM Card Before you can start using your phone, you need to order a SIM Card from a GSM service The SIM Card sometimes contains information that lets the phone automatically change the display texts into the language of the SIM Card. Your SIM Card is supplied with a security code or PIN (Personal Identity Number) that you need to enter into the phone to gain access to the phone and network. Turning On the Phone and General Information This chapter describes the display information you receive from your phone when you use it. Turning On the Phone 1. Press and hold down the NO key until you hear a click. The display will prompt you to enter the PIN (the security code that follows your SIM Card). 2. Enter the PIN and press YES. The PIN is indicated as **** in the display. If you entered the PIN correctly, you will be welcomed by your phone. Then it searches for a network. When a network is found, the indicator light on top of the phone flashes green once every second and the standby display is shown (see Figure 6). Figure 6. Standby display. PIN: Turning Off the Phone q Press and hold the NO key until you hear a click and the display is dark. LZT 126 1343/1 R1A 3 EN About the Charging Function About the Battery and the SIM Card provider. The SIM Card is a computer circuit that keeps track of your phone number, the services that you have ordered from the service provider, and your phone book information. About the Display Your phone display will help you to: Verify that you are dialling correctly. q Check your battery status. q Check your signal strength and service availability. q Indicate that you have received messages. q Table 1. Description of display icons. Icon: Indicates: The name and country of the network. The received signal strength in five steps, depending on the strength of the signal. Whether line 1 or 2 is active. The respective icon is lit when the current line is activated. These icons only show if you have two lines on your SIM Card. The divert arrow indicates that the phone has a divert active. The arrows corresponds to the line that is diverted. Shows that no ring signal will sound when the phone is ringing. That you have received a short text message or area information. That you are engaged in a call. The current battery strength ­ more bars means more power remaining. WORLD Network Signal Strength Line Looking at the Display The picture below shows how the display looks when the entire icon row is lit. Table 1 explains what each icon means. Note! All icons may not be visible at all times. Divert Silent Ring Signal Letter Figure 7. Display with all icons lit. Phone Battery 4 LZT 126 1343/1 R1A 1. 2. The parts list corresponds to Figures 8 and 9: 1. 2. 3. 4. 5. 6. 7. 8. 9. Antenna Status light Earpiece Volume keys Display Keypad Microphone (inside) Flip Microphone channel 6. 3. 13. 4. 5. 12. 7. 10. Charging connector 11. Battery 12. SIM release button 13. Phone clip 9. 8. 11. 10. Figure 8. Front view of your phone. LZT 126 1343/1 R1A Figure 9. Semi-back view of your phone. 5 EN Learning about Your Phone Making and Receiving Calls This chapter describes how to make and receive calls, how to make international and emergency calls, how to show or hide your phone number when calling (CLI ­ Calling Line Identification) and how to handle two calls simultaneously. Making a Call 1. Enter the area code and phone number. The phone number is shown in the display. If the number is longer than 10 digits, the beginning of the number will be shown as an arrow (see Figure 10). Making an International Call 1. Press and hold the zero key until the international + prefix is displayed. 2. Enter the country code, area code (without any leading zero) and the phone number. 3. Press YES to make the call. If you press YES, the number will automaitcally be redialled until the call is answered, or 10 times at the most. If you press any key, or you receive a call, the redailling is interrupted. If the redialling is successful, the phone rings twice to inform you. Receiving a Call When you receive a call, the phone rings and the indicator light on the top of the phone blinks green rapidly. The display shows Answer? Making an Emergency Call Figure 10. Number with more than 10 digits. To erase a digit, press CLR. To erase the entire phone number, press and hold down CLR for a couple of seconds. 2. Press YES to make the call. The display shows Calling, followed by Connecting and the phone icon is lit. If the number is busy, you will hear a busy tone and the display shows Busy. q Enter 112 (The international emergency number) and press YES. The display shows Emergency. The 112 emergency number can be used in any country with or without a SIM Card, provided a GSM network is within range. Answering a Call q q Press YES to answer the call When the call is finished, press NO. Rejecting a Call q Retry Function If the call connection fails and the receiver's network admits it, the display shows Retry? Press YES to redial the number, otherwise NO. Press NO or press a volume key twice when the phone rings. The display now looks like this: Ending a Call q BusyTone LZT 126 1343/1 R1A Press NO to end the call. 6 If you have been unable to answer, or you have rejected a call, the number of the unanswered call will be shown in the Missed Call menu. If you subscribe to normally show your number when calling, you can hide your number on a particular call. 1. Enter the number you wish to call. 2 Press R twice. The display shows Hide Id? 3. Press YES to make the call. When you receive a second call, you will hear a tone in the earpiece and the display shows Call Wait. q Putting a Call on Hold q Press YES answer the second call. The current call is put on hold. The display now looks like this. Press YES to put a call on hold. To put the call off hold, press YES again. Handling Two Calls Your phone can handle two calls simultaneously. This allows you to hold one call and make or receive another, then you can switch between the two calls. To be able to receive a second call, you have to activate the Call Wait function. 1 On Hold q About Calling Line Identification (CLI) The Calling Line Identification service shows the caller's phone number when you receive a call (you have to order this service). If the caller's name is stored in your phone book, the name is displayed instead of the number. To reject the second call, press zero followed by YES. Switching Between Two Calls q Press YES to switch between the two calls. Activating the Call Wait Function Press *43 # followed by YES. The display will show Please Wait followed by q Ending the Current Call and Return to the Held Call 1. Press NO to end the current call. The display shows Retrieve? and you hear two beeps. 2. Press YES within three seconds to return to the held call. If you do not press YES within three seconds, the held call is automatically ended. Showing Your Phone Number If you subscribe to normally withhold your number when calling, you can show the number on a particular call. 1. Enter the number you wish to call. 2. Press R. The display shows Send Id? 3. Press YES to make the call. ON. Deactivating the Call Wait Function q Press #43 # followed by YES. LZT 126 1343/1 R1A 7 EN If the caller's network supports it, the caller will hear a busy tone. Hiding Your Phone Number Receiving a Second Call While a Call Is in Progress Making a Second Call while a Call Is in Progress q Receiving a Third Call If you are engaged in one call and have a second one on hold, you may receive a third call. You will hear a tone in the ear piece and CallWait is shown in the display. You can only have one call on hold at a time, so you need to end the first or second call before you answer the call. You can do one of the following: Press zero followed by YES to reject the third call. q End the first call, retrieve the held call, and answer the incoming call q End both calls. The phone rings and the question Answer? appears in the display. Press YES to answer the call. q Enter the second phone number and press YES. The first call is put on hold and the display looks like this: 1 On Hold Useful Information while Talking During a call, you can: change the volume of the ear piece; use the display as a scratch pad; send DTMF tones; check the duration of the current call. Changing Volume while Talking During a call, you can use the volume keys to increase or decrease the ear piece volume (see Figure 11). Muting Microphone q Press and hold the CLR key for as long as you want the microphone muted. Sending Tone Signals During a call you can press keys 0 ­ 9, * and # to send DTMF tones. For example, to perform banking by phone or to control an answering machine. Using Phone as Scratch Pad 1. Enter a phone number on the keypad while talking. When you end the call, the number remains in the display. 2. Press YES to make the call in the display. Checking Time of Calls When you start a call (incoming or outgoing), the airtime is counted in minutes and seconds and shown on the display, like this: Figure 11. Changing volume. 8 1:34 LZT 126 1343/1 R1A This chapter describes how you navigate through the menu system to get maximum use of your phone. About the Menu System You control the functions of your phone by a menu system. Some menus have sub-menus that have individual settings. If the menu has sub-menus, three dots appear after the menu name. See the example below: Moving Through the Menu System Use these keys to move through the menu system and to find the different menus. Glossary These terms will be used throughout the manual. Scroll: Pressing the left or right arrow key to move between the menus. Select: Scrolling to a menu and then press YES. Enter: Keying in letters or numbers from the keypad. Barring... When you reach the desired menu, press YES to choose the menu. Use the L/R keys until you reach the function or setting you want. Then, in the same way you chose a menu, press YES to select the setting or function. Selecting the Key Sound Menu 1. Press CLR to clear the display. Press the left arrow key until you reach the Keysound menu. 2. Press YES. This is an example to show how to select the Key Sound menu. Press this: To: YES NO CLR confirm a setting or a selection. reject a setting or a function. return to the standby display. scroll to the right in the menu system. scroll to the left in the menu system. R L LZT 126 1343/1 R1A 9 EN Navigating the Menu System Menu Overview RecallName Store ReadMm... SendMm... AreaMm... EditMelody Ring Type Key Sound Key Lock Language 10 LZT 126 1343/1 R1A Ring Vol Info... MissedCall Set Alarm Set Clock DivertLine Networks Locks... Barring... This chapter describes how you can store phone numbers both on your SIM Card and in your phone's own memory. About the Phone Book You can store your phone numbers both on your SIM Card and in your phone's own memory. The difference between the two is you can remove the SIM Card and use all those telephone numbers in other phones, while phone's memory always stays the same no matter which SIM Card is inserted. You can store up to 50 phone numbers in the phone memory. The number of phone numbers you can store on your SIM Card is SIM Card dependent. Speed Dialling The phone numbers that you store in positions 1­9 on the SIM Card can be called by entering the position number and then pressing YES. You should, therefore, save positions 1­9 for important numbers. If you want to store the number in a different position, press CLR to erase the position number displayed and enter another number. 5. Press YES to confirm the position number. The display shows Stored. If you have chosen a position number that is already occupied, Overwrite? is displayed. Press YES to overwrite or NO to return to the position number and change it. Storing Numbers on SIM Card 1. Enter the phone number you wish to store. 2. Press the left arrow key until Store is shown and press YES twice. 3. Enter the first letter of the name by pressing the appropriate numeric key as many times as required (see Table 2 for all characters). Enter the next letter when the cursor has moved to the next letter position. The number of letters the name can have is SIM Card dependent. Press YES when you are done with the name. 4. If you want to store the phone number in the storage position suggested in the display, go directly to step 5. Storing Numbers in Phone's Memory Follow the the same procedure as storing a phone number on the SIM Card up to step 4. When you are prompted to set storage position number, press # once to enter the ¤ character (which indicates storage in phone memory) and twice to have the phone suggesting the first free storage position. Press YES to confirm the storage. International Numbers If you intend to use your phone book both at home and abroad, you should store all phone numbers as international phone numbers, i.e. with the international prefix "+" and the country code before the area code (without any leading zero) and the number. q To enter the plus prefix, press and hold the zero until you see the plus in the display. LZT 126 1343/1 R1A 11 EN Creating Your Own Phone Book About Recalling Phone Numbers You can recall a phone number any time from either the SIM Card or the phone memory. You can recall the phone number by either the name or the storage position number. Position Recall From SIM Card 1. Enter the position number and press #. 2. Press YES to call the number, or scroll until you find the number you want to call and press YES. q 3. Press # to recall number. 4. Press YES to call the number, or scroll until you find the number you want to call and press YES. Deleting Storage Position 1. Select the RecallName menu. 2. Choose the name you want to delete, press and hold CLR. 3. Press YES at the Erase prompt. Recalling by Name 1. Press CLR to erase any digits from the display. 2. Select the RecallName menu. You are prompted to enter a name. 3. Enter either the full name or the first letter and press YES. The first name that matches the letter string is displayed. If needed, scroll to the name you want. The selected name and number will blink on the display until you press the * key. 4. Press YES to call the number. Press CLR or NO to return to the standby display with the number showing. From Phone Memory 1. Press and hold # until the ¤ symbol is shown. 2. Enter the position number. Table 2. List of keypad numbers, symbols and letters. Press * to get lower-case letters. Press and hold a key to get the number directly Press a volume key together with a numeric key to get the second or third letter position. Key 1 2 3 4 5 6 7 8 9 0 Press the corresponding key this many times to get the symbol. 1 space A D G J M P T W + 2 B E H K N Q U X & 3 ? C F I L O R V Y @ 4 ! Å è ì 5 Ñ S Ü Z / Ö ß Ù 9 $ % £ 0 Ø 7 8 Ò 6 5 , Ä É 4 6 . Æ 3 7 : à 8 " Ç 9 ' 2 10 ( 11 ) 12 1 Recalling by Number ­ Speed Dialling 1. Press CLR to erase any digits from the display. 2. Enter a position number between 1 and 9. 3. Press YES to make the call. # 12 * # LZT 126 1343/1 R1A Your phone can store at least the 5 last dialled numbers. The most you can store depends on your SIM Card. 3. Press YES to call the number or scroll to the number you want to call. About Unanswered Calls Sometimes you are unable to answer a call. Then the phone keeps track of your latest missed calls in the MissedCall menu. Select the MissedCall menu. A number, a name or Unknown is shown. Now do one of the following: Press YES to see who the call is from (CLI). Press CLR to erase the call. q Scroll between the entries. q q Recalling From List of Last Dialled Numbers 1. Press CLR to erase any digits from the display. Personalizing Your Phone This chapter describes all the different ways you can personalize your phone to your own requirements. Changing Ring Volume 1. Select the Ring Vol menu. 2. Scroll to the desired ring volume, press YES. Use the volume keys to scroll silently. Turning Off Ring Volume 1. Select the Ring Vol menu. 2. Press the left arrow key until no squares are lit and press YES. The standby display now looks like this: About Ring Type You can choose between different types of ring signals. You also have the possibility to choose a melody that you have created yourself. See the chapter on Making Your Personal Ring Signal. Changing Ring Type 1. Select the Ring Type menu. The display now looks like this. Melody 1? LZT 126 1343/1 R1A 13 EN About Last Dialled Numbers 2. Press YES. The number last called is shown. Checking Unanswered Calls 2. Press the right or left arrow to listen to the different ring types. Use the volume keys to scroll silently. 3. Press YES to select your preferred ring type. Setting Alarm 1. Select the Set Alarm menu. The last alarm time is shown. 2 Enter the alarm time. 3. Press YES. The standby display now looks like this: About Display Language Your phone has many laguages that you can choose for your display texts. If you SIM card supports the automatic function, the phone has automatically chosen the SIM card default language. Note! When you change language, you change all display texts immediately. Viewing the Clock If you want to view the time on your phone, press one of the volume keys on the side of the phone. World * Setting Clock 1. Select the Set Clock menu. The display now looks like this. Your alarm works even though the phone is turned off. When the Alarm Rings... 1. Press any key and the Turn Off prompt appears. 2. Press YES to turn it off completely or any key to activate the snooze function (9 minutes). Changing Display Language 1. Select the Language menu. 2. Scroll to the language you want is shown and press YES. 14:30 2. Follow the instruction table below on how to set the clock. (Set hours before the minutes.) To change this: Do this: Hours Minutes am or pm 12-hours or 24-hours press the left or right arrow keys. press the number keys. press the * button to toggle. press the # button to toggle. Resetting Display Language to English 1. Clear the display. 2. Enter the digit string *#0000#. Turning Off the Alarm 1. Select the Set Alarm menu. The Off prompt appears. 2. Press YES. Changing Key Sound 1. Select the Key Sound menu. 2. Select the key sound you want. 3. Press YES to set the time. 14 LZT 126 1343/1 R1A This chapter describes how you can make your own ring signal. You will find one example of how to make a simple melody and one example of a little more complex melody. You will also find a table of sample melodies that you can use. About the Phone's Note System Your phone has the capability to handle a range of tones spreading over two octaves. Look in Table 3 to understand which notes and other notation corresponds to which keys. Figure 12 also explains which key goes with which note on the keypad. If you press and hold a key, you make the note long. Note! You do not need to be musical to make your own melody, just look in Table 4 for two sample melodies that are easy to create. _ 2. Press the 1 key. The display will now show a c. 3. Press the 2 key. The display now looks like this: 4. Press the 3 key. The display now looks like this: cde_ 5. Press YES to test the melody. The phone plays the melody and asks you if you want to save the melody. 6. Press YES to save the melody as an alternative in the Ring Type menu. cd_ Table 3. List of musical notation. Press this: 1­9 To: insert notes, where 1 gives a C and 9 a high D. increase or decrease the pitch in half tone steps. Press once to sharp (#), twice to flat (b), three times to get the normal pitch. insert a short pause (1/8). scroll within the melody. Press and hold to get to the beginning or end of the melody. get either a higher or a lower octave for the note you have inserted. You know it is higher as a plus sign is added in front of the note name. erase the note to the left of the cursor. If you press and hold CLR, the whole melody is erased. 15 # * 0 Simple Melody The simple melody is Do-Re-Me. This song corresponds to the C, D, and E tones on a music scale. L R Making Do-Re-Me 1. Select the Edit Melody menu. Your display now looks like this. LZT 126 1343/1 R1A CLR EN Making Your Personal Ring Signal Complex Melody The complex melody is Twinkle, Twinkle Little Star -- first section. This section corresponds to F, F, C, C, D and C tones on a music scale. 2. Press the 4 key twice. The display now looks like this: ff_ 3. Press the 8 key twice. The display now looks like this: 5. Press and hold the 8 key until you see a capital C with a plus sign in the display. The display now looks like this: c+c+d+d+C_ 6. Press YES to test the melody. The phone plays the melody and asks you if you want to save the melody. 7. Press YES to save the melody as an alternative in the Ring Type menu. Making Twinkle, Twinkle Little Star 1. Select the Edit Melody menu. Your display now looks like this. ff+c+c_ 4. Press the 9 key twice. The display now looks like this: _ f+c+c+d+d_ Table 4. List of key pressures to make melodies. s = short key pressure L = long key pressure Twinkle, Twinkle Little Star. Enter: 1s Display: c 1s c 5s g 5s g 6s a 6s a 5s g * p 4s f 4s f 3s e 3s e 2s d 2s d 1L C Fanfare. Enter: 5s Display: g Figure 12. Keypad in musical notes. 5s g 5s g * p 7s b * p 2s +d