User manual ERICSSON GF788E

Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic This manual describes Ericsson GF788e AB s Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic First edition (January 1998) This manual is published by Ericsson Mobile Communications AB, without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Ericsson Mobile Communications AB at any time and without notice. Such changes will, however, be incorporated into new editions of this manual. All rights reserved. © Ericsson Mobile Communications AB, 1998. Publication number: EN/LZT 126 1433 R1A Printed in Sweden INNOVATRON PATENTS AB s Guidelines for Safe and Efficient Use Important: Read this information before using your portable phone General Since its introduction in the mid 1980s the portable phone is one of the most exciting and innovative products ever developed. With it, you can stay in contact with your office, your home, emergency services, and others. Your telephone is a radio transmitter and receiver. When it is ON it receives and also sends out radio frequency (RF) energy. Depending upon the type of mobile phone you have purchased, it operates in different frequency ranges and employs commonly used modulation techniques. When you use your phone, the system handling your call controls the power level at which your phone transmits. For the safe and efficient operation of your phone, observe these guidelines. Exposure to radio frequency energy Er The International Commission on Non-Ionizing Radiation Protection (ICNIRP), sponsored by the World Health Organization (WHO), published a statement in 1996 which sets limits for exposure to RF fields from handheld mobile se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic phone. According to this statement, which is based on the available body of research, there is no evidence that mobile terminals meeting the recommended limits can cause any adverse health effects. All Ericsson telephones conform to the ICNIRP recommendations, and international exposure standards, such as: CENELEC European Pre-standard ENV50166-2 ANSI/IEEE C95.1-1992 (USA, Asia- Pacific) If you want to limit RF exposure even further, you may choose to control the duration of your calls and operate your phone in the most power efficient manner. may cause the phone to operate at a higher power level than needed and shorten talk and standby times. AB s Antenna care and replacement Do not use the phone with a damaged antenna. Replace a damaged antenna immediately. Consult your manual to see if you may change the antenna yourself. If so, use only an Ericsson approved antenna. Otherwise, take your phone to a qualified service centre for repair. Use only the designated Ericsson antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate the appropriate regulations. Do not use an antenna designed for any other type of portable telephone than the telephone you have purchased. Efficient phone operation How to use your phone for optimum performance with minimum power consumption: Hold the phone as you would any other telephone. While speaking directly into the mouthpiece, angle the antenna in a direction up and over your shoulder. If the antenna is extendable, it should be extended during a call. Driving Check the laws and regulations on the use of telephones in the areas where you drive. Always obey them. Also, when using your phone while driving, please: Give full attention to driving. Use hands-free operation, if available. i Do not hold the antenna when the phone is IN USE. Holding the antenna affects call quality, Pull off the road and park before making or answering a call if driving conditions so require. RF energy may affect some electronic systems in motor vehicles. In addition, some vehicle manufacturers forbid the use of mobile phones in their vehicles. Check with your vehicle manufacturer's representative to be sure your phone will not affect the electronic systems of your vehicle. Electronic devices Most modern electronic equipment, for example, equipment in hospitals and cars, is shielded from RF energy. However, RF energy from telephones may affect some electronic equipment. Turn your phone OFF in health care facilities when regulations posted in the areas instruct you to do so. Always request permission before using your phone near medical equipment. Mobile telephones may affect the operation of some implanted cardiac pacemakers, equipment for people with hearing impairments and other medically implanted equipment. Pacemaker patients should be aware that the use of a mobile phone very close to a pacemaker may cause the device to malfunction. Avoid placing the phone over the pacemaker, i.e. in your breast pocket. When using the phone, place it at your ear opposite the pacemaker. If a distance of 15cm. is kept between the phone and the pacemaker, the Er ii se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Aircraft Turn your phone OFF before boarding any aircraft. Turn off your phone before the aircraft leaves the ground. Do not use it in the air. Use it on the ground only with crew permission risk of interference is limited. Contact your cardiologist for more information. Children Do not allow children to play with your phone. It is not a toy. Children could hurt themselves or others (by poking themselves or others in the eye with the antenna for example). Children could also damage the phone or make calls that increase your telephone bills. AB s Blasting areas To prevent possible interference with aircraft systems, safety regulations require you to have permission from a crew member to use your phone while the plane is on the ground. To prevent interference with communication systems, you must not use your phone while the plane is in the air. To avoid interfering with blasting operations, turn your unit OFF when in a "blasting area" or in areas posted "turn off two-way radio". Construction crews often use remote control RF devices to set off explosives. Potentially explosive atmospheres Power Supply Connect AC (Power supply) only to designated power sources as marked on the product. To reduce risk of damage to electric cord, remove from outlet by holding onto AC adapter rather than cord. Turn your phone OFF when in any area with a potentially explosive atmosphere. It is rare, but your phone or its accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fuelling areas, such as gas stations, below deck on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Make sure the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress. To reduce risk of electric shock, unplug unit from power source before attempting any cleaning, then use soft cloth dampened on with water. Do not transport or store flammable gas, liquid, or explosives in the compartment of your vehicle which contains your phone and accessories. Product care Do not expose product to water or moisture. Example: bathtub, laundry sink, wet/damp basement, swimming pools, etc. Do not expose product to extreme temperatures such as found near a hot radiator or stove, or in a car parked in the sun. Do not expose product to extreme cold temperatures such as a car parked outdoors in winter Do not expose product to lit candles, cigarettes, cigars, open flames, etc. Use only Ericsson Original accessories. Failure to do so may result in loss of performance, fire, electric shock, or injury, and will void the warranty. Do not attempt to disassemble the product. Doing so will void warranty. This product does not contain consumer serviceable components. Service should only be performed by Authorized Service Centres. Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic The symbol on our products signifies that they have been certified according to the EMC directive 89/336/EEC, the Telecommunications directive 91/263/EEC, and the Low Voltage directive 73/23/EEC when applicable. The products fulfil the requirements according to the following standards: Cellular Phones and Accessories in Combination:ETS 300 342-1 EMC for European digital cellular telecommunications. Accessories Without Direct Connection to a Cellular Phone:EN 50081 Electromagnetic compatibility, Generic Emission Standard, and EN 50082 Electromagnetic compatibility, Generic Immunity Standard. AB s iii Er iv se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic AB s Table of Contents Guidelines for Safe and Efficient Use Assembly Instructions Assemble and Charge ­ Four Steps 1. Inserting SIM Card 2. Attaching Battery 3. Connecting Charger to Phone 4. Connecting Charger to Mains The Charging Function The Battery and the SIM Card Turning On the Phone and General Information Turning On the Phone Learning about Your Phone Making and Receiving Calls Making a Call Ending a Call Making an International Call Making an Emergency Call Retry Function E ic r se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss i 1 1 1 2 2 Receiving a Call Answering a Call Rejecting a Call Putting a Call on Hold Calling Line Identification (CLI) Handling Two Calls Conference Calls Transferring Calls Line 2 Option 7 7 8 8 8 8 9 9 9 Storing Numbers on SIM Card Storing Numbers in Phone Memory Entering Letters Recalling Phone Numbers Position Recall Changing Phone Book Entry Last Dialled Numbers Unanswered Calls 2 3 AB s 12 12 13 13 13 14 14 14 Useful Information while Talking 10 10 10 Personalizing Your Phone 15 15 15 15 15 15 15 16 16 16 16 16 16 17 17 17 v 3 4 Changing Volume while Talking Using Phone as Scratch Pad Sending Tone Signals Checking Time or Cost of Calls 10 10 4 6 Navigating the Menu System 11 11 7 7 7 About the Menu System Moving Through the Menu System Selecting the Extended Menus 11 11 7 7 7 Creating Your Own Phone Book The Phone Book 12 12 Changing Ring Volume Changing Earpiece Volume Ring Type Viewing the Clock Setting Clock Setting Alarm Turning Off the Alarm Display Language Answering Modes Handsfree Types Greeting Call Waiting Call Information Changing Key Sound Choosing Message Signal Making Your Personal Ring Signal Phone Note System Simple Melody Diverting Calls Diverting Calls Diverting from Reduced Menu Diverting from Extended Menu Viewing Status of Call Divert Cancelling Call Divert Protecting Your Keypad, Phone and SIM Card Locks Keypad Lock Card Lock (SIM) Changing PIN Unblocking with PUK Phone Lock (Un)Locking Phone Barring Calls ­ Restricting Calls Barring Calls Activating Call Bars for Any Call Type Cancelling All Call Bars Er vi se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic 18 18 18 Customizing Your Reduced Menu Customizing Menus Adding Menus Changing Menu Position Deleting Menus Resetting Menus to Original 24 24 24 Knowing Cost and Duration of Calls Call Time Call Cost 19 19 19 24 24 Specific Data Menus Having Data Menus On Diverting Fax and Data Calls AB s 28 28 28 29 29 24 29 19 Sending and Receiving Text Messages Text Messages Checking Subscription Setting Service Centre Address Sending SMS Other Message Types Receiving a Message Reading an Old Message 25 25 25 Other Networks 30 30 30 20 20 Choosing Network Selecting a Network Index 31 21 21 21 21 21 21 21 22 25 25 25 26 26 Receiving Area Information Area Information Activating the Area Information Adding a Code Erasing a Code Changing a Code 27 27 27 27 27 27 23 23 23 23 Assembly Instructions Assemble and Charge ­ Four Steps q q q q Insert the SIM Card. Attach the battery. Connect the charger to the phone. Connect the charger to the mains. Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic 1. Inserting SIM Card Removing SIM Card Place the SIM Card with the golden connectors facing down and the cut corner turned to the left (see Figure 1). Slide the SIM Card into the SIM Card slot. The SIM release button slides towards the antenna as you push in the SIM Card. 3. Pull out the SIM Card. 1. 1. 2. 2. 1. Make sure the battery is removed. 2. Slide the SIM release button towards you (see Figure 2). AB s Figure 1. Inserting SIM Card Figure 2. Removing SIM Card 1 2. Attaching Battery Place the battery on top of the phone. Push until you hear a click (see Figure 3). 1. 3. Er 2 Figure 3. Attaching battery se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic 1. Make sure the phone is turned off. 2. Press the catch on the bottom of the battery (see Figure 4.). 3. Lift the battery up and away from the phone. 1. 2. 2. Removing Battery Disconnecting Charger Lift the plug up and pull it out (see Figure 5). AB s To mains Figure 4. Removing battery Figure 5. Connecting and disconnecting charger 3. Connecting Charger to Phone 4. Connecting Charger to Mains Have the battery attached to the phone and connect the charger as described in Figure 5. Use the power plug that fits your mains. Plug the charger into a mains socket. The battery tarts charging. You can see the battery meter in the display move while charging. The Charging Function When you connect external power to the phone, the battery starts charging. When the battery is fully charged, the charging stops. You cannot overcharge your battery. When you are charging the battery, you can use your phone as normal, but the charging time will be longer. Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic The Battery Your phone is supplied with a Nickel Metal Hydride battery. The battery is not charged before shipment, even though there might be enough power to turn the phone on. The SIM Card Before you can start using your phone, you need to order a SIM Card from a GSM service provider. The SIM Card keeps track of your The Battery and the SIM Card phone number, the services that you order from the service provider and your phone book information. Your SIM Card is supplied with a security code or PIN (Personal Identity Number). You must enter this into the phone to gain access to the phone and network. AB s Note! Some services described in this manual may not be avialable in all networks. Please, see you service provider for more information. 3 Turning On the Phone and General Information Turning On the Phone 1. Press and hold down the NO key until you hear a click. The display prompts you to enter your PIN (the security code that follows your SIM Card). When your phone finds a network, the indicator light on the top of the phone flashes green once every second. The standby display is shown (see Figure 6). q 2. Enter the PIN and press YES. The PIN is indicated as in the display. If you entered the PIN correctly, you will be welcomed by your phone. Then it searches for a network. Er 4 se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Turning Off the Phone Press and hold down the NO key until you hear a click and the display turns dark. AB s 3,1 Figure 6. Standby display The Display q Your phone display helps you to: Make sure that you are dialling correctly. q Check your battery status. q Check your signal strength and service availability. q Indicate that you have received messages. Looking at the Display The picture below shows what the display looks like when the entire icon row is lit. Table 1 explains what each icon means. Figure 7. Display with all icons lit Note! All icons may not be visible at all times. Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Table 1. Description of display icons. Icon: Indicates: :25/' Network The name and country of the network. AB s Signal Strength The received signal strength in five steps. Line Whether line 1 or 2 is active. These icons only show if you have two lines on your SIM Card. Divert That the phone has a divert active. The arrows corresponds to the diverted line. Silent Ring Signal That no ring signal sounds when the phone is rings. Letter That you have received a short text message or area information. Phone That you are engaged in a call. Battery The current battery strength ­ more bars there are the more power there is. 5 Learning about Your Phone 1. Antenna The parts list corresponds to Figures 8 and 9: 2. Status light 3. Earpiece 5. Display 4. Volume keys 6. Keypad 8. Flip 7. Microphone (inside) 9. Microphone channel 10. Charging connector 11. Battery 12. SIM release button 13. Phone clip holder Er 6 se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic 1. 2. 3. 13. 4. 5. 6. 12. 7. 8. 11. 9. AB s 10. Figure 8. Front view of your phone Figure 9. Rear view of your phone Making and Receiving Calls Making a Call 1. Enter the area code and phone number. The phone number appears in the display. If the number is longer than 10 digits, the beginning of the number is shown as an arrow (see Figure 10). Figure 10. Number with more than 10 digits To erase a digit, press CLR. To erase the entire phone number, press and hold down CLR for a couple of seconds. 2. Press YES to make the call. The display shows Calling, followed by Connecting. The phone icon appears. If the number is busy, you hear a busy tone and the display shows Busy. Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Holding the Phone Put the earpiece to your ear for the best speech and reception quality (see Figure 11). Making an Emergency Call q Enter 112 (the international emergency number) and press YES. The display shows Emergency. The 112 emergency number can be used in any country with or without a SIM Card, if a GSM network is within range. Note! Some GSM networks do not support the international emergency number. AB s Figure 11. Holding your phone Retry Function Ending a Call q Press NO to end the call. If the call connection fails, the display shows Retry? Press YES to redial the number, otherwise NO. Making an International Call Receiving a Call 1. Press and hold the zero key until the international + sign is displayed. 2. Enter the country code, area code (without any leading zero) and the phone number. 3. Press YES to make the call. When you receive a call, the phone rings and the indicator light on the top of the phone blinks green rapidly. The display shows Answer? Answering a Call q Press YES to answer the call q When the call is finished, press NO. 7 Rejecting a Call q Press NO or a volume key twice when the phone rings. The display now looks like this: If the caller's network supports it, the caller hears a busy tone. If you have been unable to answer, or you have rejected a call, the number of the unanswered call is shown in the display until you press CLR (this depends on your subscription). Putting a Call on Hold If you are engaged in a call, you can put it on hold by pressing YES. This mutes the microphone so that you can have a private conversion without the person at the other end hearing. To put the call off hold, press YES again. Calling Line Identification (CLI) The Calling Line Identification service shows the caller's phone number when you receive a call (you have to order this service). If the caller's name is stored in your phone book, the name is displayed instead of the number. Er 8 se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic %USY7ONE If you subscribe to withhold your number when calling, you can show the number on a particular call. 1. Enter the number you wish to call. 2. Press . The display shows Send Id? 3. Press YES to make the call. q Showing Your Phone Number Receiving a Second Call While a Call Is in Progress When you receive a second call, you will hear a tone in the ear piece and the display shows Call Wait. Press YES answer the second call. The current call is put on hold. The display now looks like this. AB s 2N +OLD Hiding Your Phone Number q To reject the second call, press zero followed by YES. If you subscribe to show your number when calling, you can hide your number on a particular call. 1. Enter the number you wish to call. 2 Press twice. The display shows Hide Id? 3. Press YES to make the call. Switching Between Two Calls q Press YES to switch between the two calls. Ending the Current Call and Return to the Held Call 1. Press NO to end the current call. The display shows Retrieve? and you hear two beeps. Handling Two Calls Your phone can handle two calls simultaneously. This allows you to hold one call and make or receive another. You can switch between the two calls. 2. Press YES within three seconds to return to the held call. If you do not press YES within three seconds, the held call is ended automatically. To receive a second call, you must activate the Call Wait function (see the chapter on Personalizing Your Phone on page 12). Making a Second Call while a Call Is in Progress q Enter the second phone number and press YES. The first call is put on hold and the display looks like this: Receiving a Third Call If you are engaged in one call and have a second one on hold, you may receive a third call. You hear a tone in the ear piece and CallWait is shown in the display. You can only have one call on hold at a time, so you need to end the first or second call before you answer the third one. You can do one of the following: q q Press zero and then YES to reject the third call. End the first call, retrieve the held call, and answer the incoming call. q End both calls. The phone rings and the question Answer? appears in the display. Press YES to answer the call. Conference Calls The conference call service allows you to have a joint conversation with up to five people. You Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Line 2 Option may put an individual or a group or conference members on hold while you add other people to the conference call. You may also put conference members on hold while you talk to someone privately. The Conference Call service may not be available in all networks. Contact your operator to find out whether your network supports it. then YES. You are then disconnected from both calls. 2N +OLD Initiating a Conference Call Your phone can support two phone lines if your service provider offers this service. Having two different phone numbers on the same SIM Card makes it easy to keep business and private calls separate. AB s 1. Call the first person you wish to include in the conference call. 2. Put this person on hold by pressing YES. When you receive a call, the display shows Answer? After that it toggles between L1? (or L2?) and the caller's number. When you want to make a call, you choose the phone line by toggling between L1 and L2). q 3. Call the second person you wish to include in the conference call. 4. Press 3, then YES to include the two people in the conference. You can put the conference group on hold and then add a third member by repeating steps 2 to 4. It is possible to add up to five members in this way. To toggle between L1 and L2, press the right arrow key then YES. Divert L1 and L2 Transferring Calls If you have one active call and another call on hold, you can connect the two by pressing 4, When a second line is introduced, Line 2 is added to the menu structure and the Divert menu splits into Divert L1 and Divert L2 so that you will be able to divert each line separately (see Chapter Diverting Calls on page 19). You can divert Line 1 to an answering machine, for instance, and keep Line 2 active. 9 Useful Information while Talking Changing Volume while Talking Using Phone as Scratch Pad During a call, you can use the volume keys to increase or decrease the earpiece volume (see Figure 12). Figure 12. Changing volume Er 10 se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Checking Time or Cost of Calls 1. Enter a phone number on the keypad while talking. When you end the call, the number remains in the display. 2. Press YES to make the call in the display. When you start a call (incoming or outgoing), the airtime is counted in minutes and seconds and shown in the display like this: AB s Sending Tone Signals During a call you can press keys 0 ­ 9, and to send DTMF tones. For example, to use telephone banking services or to control an answering machine. If you want the phone to keep track of the costs you need to set that specifically. Check if your service provider supports this service (see chapter Knowing Price and Duration of Calls on page 28). Navigating the Menu System About the Menu System q q You control the functions of your phone by a menu system. There are two sizes: Rreduced Extended In this manual package, there is a separate leaflet which describes all the original settings of both the reduced and extended menu system. Hint! When you go through this manual, have the leaflet with all menus handy at the same time. Some menus have sub-menus that have individual settings. If the menu has sub-menus, three dots appear after the menu name. See the example below: The Reduced Menus The reduced menu consists of those functions and settings you probably use most. This menu system can be personalized to fit your specific needs. When you personalize the system, you Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic move menus and sub-menus from the extended menu system to the reduced. You learn how to personalize your menus in Customizing Your Reduced Menu System on page 24. Press: YES NO To: The Extended Menus CLR confirm a setting or a selection. reject a setting or a function. return to the standby display. scroll to the right in the menu system. scroll to the left in the menu system. AB s The extended menu contains all the functions and settings available from the phone. Glossary These terms will be used throughout the manual: Scroll: Press the left or right arrow key to move between the menus. Select: Scroll to a menu and then press YES. Enter: Key in letters or numbers from the keypad. Moving Through the Menu System Use these keys to move through the menu system and to find the different menus. Selecting the Extended Menus 6ETTINGS When you reach the desired menu, press YES to choose the menu. Use the / keys until you reach the function or setting you want. Then, in the same way you chose a menu, press YES to select the setting or function. 1. Press CLR to clear the display. Press the left arrow key four times until you reach the Menu Size menu. 2. Press YES. You are now in the Menu Size menu where you can switch to the Extended menu mode. 3. Press YES at the Extend prompt. 11 Creating Your Own Phone Book The Phone Book You can store phone numbers in two places: on your SIM Card and in your phone's own memory. The choice is based on your needs. If you use one SIM Card in many phones, the phone book stored on the SIM Card is always available to you. If you have one telephone and use several SIM Cards, the phone's phone book is always available to you. You can store up to 99 phone numbers in the phone memory. SIM Card capacities vary. International Numbers If you intend to use your phone book both at home and abroad, you should store all phone numbers as international phone numbers, i.e. with the international (+) sign and the country code before the area code (without any leading zero) and the number. q To enter the (+) sign, press and hold 0 (zero) until you see + in the display. Speed Dialling Er 12 The phone numbers that you store in positions 1­ 9 on the SIM Card can be called by entering the position number and then pressing YES. You should, therefore, save positions 1­9 for important numbers. se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Storing Numbers on SIM Card 1. Select the Store menu (second to the left from standby) by pressing YES. 2. If you don't have the right phone number in the display from the start, clear the display and enter it now. 3. Press YES. The display shows Name: overwrite or NO to return to the position number and change it. 6. Press YES to confirm the position number. The display briefly shows Stored. The listing has been saved. The display changes to Store. You are back to the Store menu and can now enter another phone number. AB s Storing Numbers in Phone Memory 4. Enter the first letter of the name by tapping the key with the appropriate letter. If it is the second letter, you need to tap the key twice to produce it (see Entering Letters). Wait for the cursor to move to the right before entering the next letter. The number of characters allocated for each name vary with SIM Cards. Press YES when you have keyed in the name. The display shows POS: and a number. This is the first available position on the SIM Card. 5. If you want the storage position suggested in the display, press YES (see step 6). If you want to store the number in a different position, press CLR to erase the suggested position number and enter another number. If you choose a position number that is already occupied, Overwrite? is displayed. Press YES to Follow the same procedure as for storing phone numbers on SIM Card, up to step 5. This is where you are prompted to accept or reject a storage position number. The suggested number is for a SIM Card position, if there is one available. Otherwise the phone suggests a position in the Phone memory. Clear the number by pressing CLR. Access the phone memory by pressing . The symbol } appears in the display. Press again. The symbol } is now followed by a number which represents the first available position in the phone memory. Confirm by pressing YES or change the digit. Entering Letters You can enter letters and other characters using the keypad: Press the appropriate key, 1-9, 0 or repeatedly until the desired letter, character or digit appears in the display. For example, to enter an A, press number key 2. To enter B, press number key 2 twice. 1 2 3 4 5 6 7 8 9 0 Note! In the letter mode, you can still enter digits but they are positioned deep. Hold down the key until the digit appears in the display instead of tapping. Er se n l U tio ia ca rc ni eu mm om om CC or le t f bi oo NM on ss ic Enter the letter A for example and then press *. The capital A is replaced by a lower case a. All letters will now be lower case until you press * again. 4. Press YES to call the number. Entering Lower Case Letters The selected name and number flash in the display until you press the key. Recalling by Number ­ Speed Dialling Space - ?! , . : " '( ) 1 ABCÅÄÆàÇ2G DEFèÈ3DF GHIì4 JK L 5 L MNOÑÖØò6 PQRSb7PS TUVÜù8 WXYZ9 0+&@/$%£QXYW Note! Pressing one of the volume keys together with a number key, will get you to the second or third letter position directly. To exit the letter mode and return to standby, clear the display, by pressing CLR. Then press CLR again. 1. Press CLR to erase any digits from the display. AB s 2. Enter a position number between 1 and 9. 3. Press YES to make the call. Position Recall From SIM Card 1. Enter the position number and press . 2. Press YES to call the number, or scroll until you find the number you want to call and press YES. Press CLR to return to the standby display with the number showing. q Press NO to return to the standby display. q Recalling Phone Numbers You can recall a phone number any time from either the SIM Card or the phone memory. You can recall the phone number either by the name or the storage position number. Recalling by Name From Phone Memory 1. Press CLR to erase any digits from the display. 1. Press and hold until the } symbol appears. 2. Select the RecallName menu. You are prompted to enter a name. 2. Enter the position number. 3. Press to recall number. 3. Enter either the full name or the first letter and press YES. The first name that matches the letter is displayed. If necessary, scroll to the name you want. 4. Press YES to call the number, or scroll until you find the number you want to call and press YES. 13 Changing Phone Book Entry 1. Select the EditPhBook menu. 2. Enter either the full name or the first letter and press YES. The first name that matches the letter is displayed. If necessary, scroll to the name you want and press YES. 3. Scroll through the name to change it letter by letter and press YES. The phone number is displayed. 4. Scroll through the phone number to change it digit by digit and press YES. The position number is displayed. 5. Enter a new position number and press YES. If the new position is already occupied, you will be asked to Overwrite? the position. Er 14