User manual FANTOM TWISTER FM760 - INSTRUCTION MANUAL

INSTRUCTION MANUAL VACUUM CLEANER FM760 Contents IMPORTANT SAFETY INSTRUCTIONS NAME OF EACH PART PREPARATION BEFORE USE USING THE VACUUM CLEANER USING THE ATTACHMENTS EMPTYING THE DUST COMPARTMENT CLEANING THE FILTERS CLEARING BLOCKAGES IN THE SUCTION HOSE AND CLEANING THE AGITATOR ASSEMBLY REPLACEMENT INSTRUCTIONS TROUBLESHOOTING REPLACEMENT PARTS LIMITED WARRANTY 1 3 4 6 8 9 10 11 12 16 16 17 HOUSEHOLD USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following. READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING - To reduce the risk of fire, electric shock or injury: 1. Do not leave the vacuum cleaner when plugged in. Unplug it from the outlet when not in use and before servicing. 2. Do not use outdoors or on wet surfaces. 3. Do not allow it to be used as a toy. Close attention is necessary when used by or near children or infirmed persons. 4. Use only as described in this manual. Use only the manufacturer's recommended attachments. 5. Do not use with a damaged cord or plug. If the vacuum cleaner is not working as it should, or if it has been dropped, damaged, left outdoors or dropped into water, return to FANTOM at 94 Main Mill street, Door 16, Plattsburgh, NY 12901. 6. Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces. 7. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord. 8. Do not handle the plug or the vacuum cleaner with wet hands. 9. Do not put any objects into the openings. Do not use with any opening blocked: keep free of dust, lint, hair and anything that may reduce air flow. 10. Keep hair, loose clothing, fingers and all the parts of your body away from openings and moving parts. 11. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. 12. Do not use without dust compartment and filters in place. 13. Turn off all controls before unplugging. 14. Use extra care when cleaning on stairs. 15. Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present. 1 REV. 05/02B 16. Do not touch the agitator while it is spinning. 17. Do not place any heavy items on top of the vacuum cleaner. 18. Do not step on the hose or pull it too strongly. 19. Do not pick up items such as pieces of waste paper or cloth which look as though they may cause the hose to become blocked. 20. Do not clean or store the vacuum cleaner in places where there are high temperatures. 21. Store the vacuum cleaner away from excessive humidity. 22. When carrying the vacuum cleaner, hold it by the carrying handle. 23. Before servicing the vacuum cleaner, allow all metal parts to cool first. 24. Always place foot on handle release when adjusting the handle position of the vacuum cleaner. 25. If the supply cord of this appliance is damaged, it must only be replaced by FANTOM , because special purpose tools are required. SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only. Note to user concerning attachment plug: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2 NAME OF EACH PART FRONT REAR Handle Release Button C Suction Hose Release Button A Cord Storage Hooks Release Button B Carrying Handle ON/OFF Switch Crevice Tool Release Button D Upholstery Tool Dust Compartment Dusting Brush Filter Cover Wand Power Cord Power Cord Plug Height Adjustment Headlight Lever Handle Release Lever Set the ON/OFF switch to " ON " to light the headlight. Rug/Floor (Tools) SELECTOR Cleaning Utensil Operate vacuum cleaner only at the voltage specified on name plate. 3 PREPARATION BEFORE USE Caution: Do not connect the power cord plug to the wall outlet until assembly is completed. Attaching the handle Set the vacuum cleaner 1 to the upright position. lnsert the 2 as shown handleillustration. in the Attaching the suction hose & attachments Wand Suction Hose Crevice Tool Hose Hook Upholstery Tool Dusting Brush 4 PREPARATION BEFORE USE WINDING THE POWER CORD Hook the power cord over 1 the clip which is located on the upper cord storage hook as shown. Plug side Wind the power 2 storage hooks. cord around the cord Secure the power cord plug on the power cord. Cord Storage Hooks Clip RELEASING THE POWER CORD Rotate the 1 downward.upper cord storage hook to the 2 Return the hook before upright position attempting to rewind the power cord. Upper Cord Storage Hook INSERTING THE POWER CORD PLUG WARNING: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way. 5 USING THE VACUUM CLEANER ON/OFF SWITCH Start or stop vacuum cleaner by pushing on the switch. ADJUSTING THE HANDLE The handle of this vacuum cleaner can be set to one of three positions -Upright, Normal or Parallel. Place your foot on handle release lever as shown and pull back on the handle until it releases from its upright position. Handle Release Lever Upright position The handle is normally locked in this position for storage or when using the attachments. Push the handle forward until it locks. Normal position This position is used for normal cleaning. Parallel position Handle Release Lever This position is used for cleaning under furniture. 6 USING THE VACUUM CLEANER HEIGHT ADJU STMENT LEVE R Cautio n: Height Adjustment Lever The nozzle head can be adjusted to four different height settings. Before using the height adjustment lever,please make sure the nozzle head is tilted backward from the floor. Nozzle Head Set the height adjustment to the appropriate carpet length. Use the 3 rd( setting. Use the 4 th( setting. )height )heigh t RUG/FLOOR (TOOLS)SELECTOR The RUG/FLOOR(TOOLS)selector should only be adjusted while the vacuum cleaner is turned on RUG Position and in the upright position. When cleaning a rug or carpet,first turn the ON/OFF switch to the ON position,and then set the RUG/FLOOR(TOOLS)selector to the RUG position. FLOOR Position 1 2 When cleaning a bare floor or when using one of the attachments, set the RUG/FLOOR EDGE CLE AN ING RUG/FLOOR(TOOLS)selector (TOOLS)selector to the FLOOR position. Caution: Do not change the setting of the RUG/FLOOR(TOOLS)selector while the vacuum cleaner is turned off. This vacuum cleaner is equipped with an "edge cleaning" function for cleaning carpet edges near baseboards and stationary furniture. 7 USING THE ATTACHMENTS Caution: When using one of the attachments during cleaning,set the vacuum cleaner to the upright position. the attachments from the 1 Removecleaner. vacuum 2 Press the release button C to disconnect the handle from the vacuum cleaner. Wand Crevice Tool Release Button C Caution: When removing the attachments,pull them in the directions shown in the Upholstery Tool illustration.Pulling them in the wrong direction or pulling them forcefully may cause damage to the attachment clamp . Dusting Brush Attachment Clamp 3 Attach the attachments on the handle. Attach the attachments as shown below. Wand Crevice Tool Upholstery Tool Suction Hose Dusting Brush When you have finished using the attachments,replace them in their original positions as shown on page 4. 8 EMPTYING THE DUST COMPARTMENT Caution: Be sure to turn the ON/OFF switch to the "OFF" position and disconnect the power cord from the wall outlet before cleaning. 1 Empty the dust compartment when contents reach the MAX mark. 2 Press the release button A meanwhile press the release button B to remove the dust compartment. Release Button A Release Button B MAX mark 3 3 Press the release lever to open the trapdoor. Release Lever Turn the handle 4 direction spinnerto emptyseveral times in the shown the dust compartment. Trapdoor Spinner Handle Reattaching the Dust Compartment Close the trapdoor and insert the the dust 1 dust compartment into the grooveprojection onbody. 2 Push the body compartment into on the main the main as shown to reattach. Projection Groove 9 CLEANING THE FILTERS 1 Remove the dust compartment.(refer to page 9) Set the dust compartment to the 2 position.Open the trapdoor,then parallel push the release button E and pull out the main filter. The main filter and prefilter will be removed at the same time. Caution: Do not push the release button E at the upright position. As this may drop or damage the main filter and prefilter. the and prefilter with 3 Clean bothmain filterdry completely. a soft-bristled brush and rinse with cold water. Allow items to Caution: Do not use a hard-bristled brush to clean filters. This may result in damage to the filters. Do not attempt to dry with a hair dryer or by placing in a clothes dryer.Hot air may cause the filters to warp. Release Button E Cleaning Utensil To maintain optimum suction power, the dust filter fins should be kept clean of dirt. Clean the filter fins free of dirt with the forked end of cleaning utensil as shown. Cleaning Utensil Reattaching the filters 1 Insert the main filter into the prefilter as shown. Prefilter onto the main filter 2 Holddust compartment. and insert into the Align the ribs of the main filter to match the shape of the opening in the dust compartment and press firmly to insert. Dust Compartment Hole Main Filter Ribs 3 Close the trapdoor. 10 CLEARING BLOCKAGES IN THE SUCTION HOSE AND CLEANING THE AGITATOR ASSEMBLY Caution: Be sure to turn the ON/OFF switch to the "OFF" position and disconnect the power cord from the wall outlet before clearing any blockages in the suction hose and cleaning the agitator assembly. Clearing blockages in the suction hose Set the 1 Removevacuum cleaner to the upright position. the cuff from any from the hose. 2 then remove hoseblockagesthe suction inlet and Pull inspection cover out the bypass tube assembly. 3 pushthe dust dust clogging theaway from body and cuff to inlet,and dust inspection cover to the bypass tube assembly. 4 Reattach theonhose vacuum the suctioncheck that the Now switch the cleaner to Hose Cuff Suction Inlet Dust Inspection Cover Bypass Tube Assembly the blockage has been properly cleared. If the hose is still blocked, the suction force will be weak. Clearing blockages in the nozzle head Remove the bottom plate (refer to page 14) Remove any blockages from the nozzle head. Reattach the bottom plate to the nozzle head,and then operate the vacuum cleaner to check that the blockage has been properly cleared. If the nozzle head is still blocked, the suction force will be weak. Nozzle Head Cleaning the blockage in the nozzle air inlet pipe If the nozzle head still appears to be blocked, please clear the blockage in the nozzle air inlet pipe. Press release button F to remove the upper case. Remove the blockage in the nozzle air inlet pipe. Reattach the vacuum cleaner. Release Button F Release Button F Nozzle air inlet pipe Nozzle air inlet pipe Caution: Make sure that the Release Button F is at the original position. Cleaning the agitator assembly When threads get caught in the agitator assembly, clean the assembly. Remove the bottom plate (refer to page 14). Remove threads caught in the assembly by cutting them with scissors. Scissors Threads 11 REPLACEMENT INSTRUCTIONS Caution: Be sure to turn the ON/OFF switch to the"OFF" position and disconnect the power cord from the wall outlet before replacing any of the parts below. REPLACING THE HEADLIGHT LAMP 1 Set the vacuum cleaner to the parallel position. 2 Loosen the screws to remove the lens. 3 When removing the headlight lamp, be careful not to pull on the headlight lamp wiring. Lens Headlight Lamp Screw 4 Remove the lamp by pushing it gently in the direction of the arrow and then turning it counterclockwise. Lamp Socket 5 Push a new lamp gently into the socket and turn it clockwise to tighten it . Use a standard bayonet base appliance lamp rated at 120V and 15W (LAMP MAX.15W). Socket Caution: Be careful not to clamp the headlight lamp wiring. 6 Reattach the lens and fasten the screws. 12 REPLACEMENT INSTRUCTIONS Caution: Be sure to turn the ON/OFF switch to the"OFF" position and disconnect the power cord from the wall outlet before replacing any of the parts below. REPLACING THE FLAT BELT 1 2 Remove the bottom plate. (refer to page 14) Lift out the agitator assembly,and then remove the flat belt from the motor shaft and the agitator pulley. Motor Shaft Flat Belt Agitator Assembly 3 Place a new flat belt onto the motor shaft and pulley. Motor Shaft Flat Belt Flat Belt Pulley Place the agitator assembly into the grooves in the nozzle head, making sure that the new flat belt slides securely into the guide. 4 Bearing Holder Groove Nozzle Head Caution: Install the flat belt so that it has no twists in it,and so that all components turn smoothly. 5 13 Reattach the bottom plate (refer to page 14) REPLACEMENT INSTRUCTIONS REMOVING THE BOTTOM PLATE 1 Set the vacuum cleaner to the parallel position and turn it over. Latch Pull here Slide 2 of thethe latch in the direction arrow. Remove the bottom plate 3 the tabs as illustrated. by pulling Bottom Plate REATTACHING THE BOTTOM PLATE as shown. the projection on the bottom 1 Insertthe groove on the nozzle headplate 2 Push the bottom plate Press into and set the bottom plate in place. Press Bottom Plate Projection Groove 3 Latch Slide the latch in the direction shown. 4 Turn the vacuum over and place in the upright position. Nozzle Head Height Adjustment Lever 14 REPLACEMENT INSTRUCTIONS REPLACING THE HEPA FILTER Under normal usage, the HEPA Filter will not require replacement; however, vacuuming large amounts of extremely fine dust, powder or similar material over a long period of time may decrease airflow performance through the filter. If this occurs, it may become necessary to replace the HEPA Filter. Only use genuine FANTOM replacement filters. Release button D 1 2 1 Press the release button D at points 1 and pull the filter cover away from the vacuum cleaner. Filter Cover 2 Remove the HEPA filter. HEPA Filter Caution: Do not attempt to wash the HEPA filter. Always replace the old filter with a new one. a new filter with the seal 3 Insert inside HEPAvacuum cleaner. to the of the Reattach the filter cover. Caution: Be sure that seal on the HEPA filter is inserted towards the inside of the vacuum cleaner. The filter cover should be correctly oriented when it is reattached. Do not reattach it upside down. Seal 15 TROUBLESHOOTING If there is a problem with the vacuum cleaner, carry out the following checks to find the cause. If the problem still persists after the checks have been made, do not use the vacuum cleaner to prevent the possibility of an accident occurring. Turn the ON/OFF switch to the "OFF" position, disconnect the power cord from the wall outlet, and contact FANTOM Customer Service at 1-800-275-9251. Or visit our website at www.fantom.com Problem The motor does not operate when the ON/OFF switch is set to the "ON" position. Suction force is weak. Cause The power cord plug is not securely inserted into the wall outlet. Remedy Insert the power cord plug securely into the wall outlet.(refer to page 5 ) Empty the dust compartment. (refer to page 9) Remove the blockage. (refer to page 11) Remove the blockage. (refer to page 11) Clean the filters. (refer to page 10) Remove the blockage. (refer to page 11) Replace the flat belt. (refer to page 12 ) The dust compartment is full. The suction hose is blocked. The nozzle head is blocked. The filters are dirty. The nozzle air inlet pipe is blocked. The agitator does not operate. The flat belt is worn or broken. TO ORDER REPLACEMENT FILTERS CALL 1-800-275-9251 16 ONE (1) YEAR LIMITED WARRANTY FANTOM warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to In US: FANTOM, 94 Main Mill Street, Door 16, Plattsburgh N.Y. 12901 If the appliance is found by FANTOM to be defective in material or workmanship, FANTOM will repair or replace it free of charge. Proof of purchase date and $19.95 to cover the cost of return shipping and handling must be included. * Non-durable parts including, without limitation, dust cup filters, filters, belts, brushes and electrical parts which normally require replacement are specifically excluded from warranty. The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by FANTOM. This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of FANTOM if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is FANTOM liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. *Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package "ATTENTION CUSTOMER SERVICE". $ OWNERSHIP REGISTRATION CARD Please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable us to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions. RETURN TO FANTOM, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901 Model FM760 ____________________________________________________________________________________________ Appliance model ____________________________________________________________________________________________ Date purchased Name of store ____________________________________________________________________________________________ Owner's name ____________________________________________________________________________________________ Address City State Zip Code Printed in China