NOTE TO THE INSTALLER FINAL CHECK LIST REMOVE TRANSIT BOTTOM PACKER DRAIN HOSE After you have followed the procedures on the previous pages. Check the following. INSTALLATION INSTRUCTIONS FOR YOUR ECO SMART WASHER BEFORE YOU BEGIN - READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to installer: Be sure to leave these instructions with the Customer. Note to Consumer: Keep these instructions with your Use & Care Book for future reference. Note: This appliance must be properly grounded. INSTALLATION REQUIREMENTS LOCATION Washer must be installed on firm flooring to minimize vibration during spin cycles. Concrete flooring is best, but wood base is sufficient providing floor support meets FHA standards. Washer should not be installed on rugs or exposed to the weather. Washer end of hose Lid Clearance Standpipe Height 33 1/2" to 78" Faucet end of hose HAVE YOU CARRIED OUT THE FOLLOWING INLET HOSE CONNECTIONS Faucet end of hose SPECIFICATIONS PULL HOSE THROUGH GUIDE 3/4" (20mm) PLUMBING Bottom packer MUST be removed from the base of the washer, before the basket packer is removed. Filter end must be connected to faucet. Water Temperature Your cold water should not exceed 95°F (35°C) or your hot water exceed 150°F (65°C). Temperatures above this may damage your washer. HEIGHT The drain hose guide MUST be fitted to the drain hose and should not extend more than 3/4" (20mm) from the end of the guide. Place the drain hose in tub or standpipe. Washer end of hose. Shut off valves LEVELING Make sure washer is level and four rubber inserts are properly installed. GROUNDING MUST be properly grounded to conform to local codes and ordinances. WARNING: Improper connection of equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. OPERATION 1.Turn faucets on. Check for leaks, noise, vibration, correct water temperatures and proper operation in spin. 2.Turn hot and cold water faucets off and instruct customer to do the same when washer is not in use. 3. Give customer the Use & Care Book and Installation Instructions. Both hot and cold shut-off valves (faucets) should be available in laundry area. Drain Water may be drained into a standpipe or set tub. The standpipe must be 11/2" (38mm) minimum inside diameter and must be open to the atmosphere. Allow for adjustable feet WIDTH DEPTH Inlet water pressure Max 150 psi (1MPa) Min 3 psi (20kPa ) All models 251/2" (650mm) 251/2" (650mm) 1/2"- 411/2" (1020-1050mm) 40 551/2"- 561/2" (1410-1440mm) ELECTRICAL This appliance must be supplied with 110V-120V, 60Hz, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time delay fuse. DIMENSIONS MODEL DEPTH WIDTH HEIGHT to top of console HEIGHT LID OPEN READ AND OBSERVE ALL SAFETY INSTRUCTIONS - CONSULT THE PRODUCT USE & CARE BOOK FOR CUSTOMER CAUTIONS Specification subject to change without notice P/N 420264A Specification subject to change without notice STEP 1 REMOVE BOTTOM PACKER 1. Remove outer packaging. 2. Tilt the machine backwards and walk the machine off the bottom packer. The plastic bottom packer can now be removed from the machine. STEP 3 Drain Hose 1. Carefully pull the drain hose out from the back of the washer by pulling the exposed part of the hose downwards and then out. 2. The hose guide is used to guide the drain hose over the tub or standpipe. It MUST be fitted to the drain hose. To prevent siphoning the drain hose should not extend more than 3/4" (20mm) from the end of the guide. If necessary, the drain hose can be trimmed to length Note: If there is a cold water supply only, an inlet valve cap (available from Fisher & Paykel) MUST be connected to the hot valve. The cap prevents water leaking out the hot valve. Cold water connection is required. 5. Use the walls and adjacent counter tops as a sight guide to check to see if washer appears level. Readjust the feet if necessary. 6. Please test machine in permanent press cycle. 7. Open lid and check the washer basket to see that it sits slightly forward of centre (see illustration). SPECIAL REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION The minimum ventilation clearance between the washer and adjacent walls or other surfaces is: 1" (25mm) either side and front 3" (75mm) rear NOTE: The clearances stated are minimums. Consideration must be given to providing adequate clearance for installation and servicing. Minimum vertical space from floor to overhead shelves, cabinets, ceilings etc is 59" (1500mm). Closet doors must be louvered or otherwise ventilated and have at least 60 square inches open area for a washer only, or if the closet contains both a washer and dryer, doors must contain at least 120 square inches of open area equally distributed. Caution: DO NOT INSTALL THIS APPLIANCE IN A CLOSET WITH A SOLID DOOR. LOUVERED DOOR WASHER & DRYER GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or break down, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged in to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING: Improper connection of equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. STEP 5 LEVELING THE WASHER Leveling Feet 1. Insert the four rubber leveling feet inserts into the feet on the base of the washer. INCORRECT ADJUSTMENT Caution: Operating the machine when the bottom packer is in place can result in damage to the machine. PULL HOSE THROUGH GUIDE 3/4" (20mm) STEP 2 REMOVING BASKET PACKER AND ACCESSORIES 1. Lift lid and remove cardboard basket packer from under lid. 2.Keep the bottom packer and basket packer in case they are required for future transit. 3. Remove hoses, accessories and installation pack. 3.Place the drain hose in laundry tub or standpipe. Note: · In multi-storey apartments or any upper floor, the machine should be installed on a drained floor · Check that the tub or standpipe is free from lint or other obstructions. · In basement installation do not exceed standpipe height. (78") CORRECT ADJUSTMENT 8. Close the lid. Visually check that the lid and topdeck are aligned. OPERATION 1.Turn faucets on. Check for leaks, noise, vibration, correct water temperatures and proper operation in spin. Check lid locks during spin. 2. Turn hot and cold water faucets off and instruct customer to do the same when washer is not in use. 3.Give customer the USE & CARE Book and Installation Instructions. 2. Move the washer into its final position. We suggest a minimum clearance of 1" (25mm) on each side for ease of installation. 1" (25mm) 1" (25mm) If it does not look like the diagram below, adjust one of the front feet slightly until it matches. The installation pack contains the following: · 4 rubber inserts for the leveling feet · 1 drain hose guide STEP 4 Inlet Hoses 1.Install hoses with straight end (with filters) onto the faucets. 2.Install elbow ends onto washing machine (inlet valves are marked on the back of the machine H=hot, C=cold) 3. Turn on water and check hose connections for leaks. Make sure there are no kinks in the hoses. 4. It is IMPORTANT to level the washer to give proper performance in spin. Washer end of hose Faucet end of hose Lid Alignment lid 60 Sq. In (388 Sq. cm) SPECIAL INSTRUCTIONS 1. The washer may give warning signals when low water pressure, or drain problems are encountered. Consult the USE & CARE Book. 60 Sq. In (388 Sq. cm) x Topdeck lid Aft ma inst lid 2. Note user options shown in the USE & CARE Book. If further help is needed concerning this appliance call: MOBILE HOME INSTALLATION Installation must conform to STANDARD FOR MOBILE HOMES, ANSI A119.1 and NATIONAL MOBILE HOME CONSTRUCTION & SAFETY STANDARDS ACT OF 1974 (PL93-383). BASKET PACKER Make sure the rubber inserts are in the adjustable feet on the base of the washer. Adjust the feet by unscrewing/screwing to make sure the washer is level and cannot rock. Topdeck lid To foo Ch ma not TOLL FREE 1 888 9FNP USA (1 888 936 7872) IN CANADA Direct 1 877 744 7400 or write: Topdeck x Fisher & Paykel Appliances Inc., 27 Hubble, Irvine, CA 92618 ...