User manual FITNESSQUEST GAZELLE POWER PLUS ASSEMBLY

HYDRAULICS INSTALLATION PARTS (after complete unit is assembled) fastener pack mounting brackets M8 x 70mm hex bolts, washers and nylon nuts washers (4) 12mm springs clips 1/20/05 We recommend having someone available to help you. Due to the size and weight of some of the pieces, assembly is easier and safer if there are two people. nut caps hydraulics pin left right closed end wrenches washers (2) 8mm ASSEMBLY INSTRUCTIONS nuts Occasionally our products contain components that are pre-lubricated at the factory. We recommend that you protect flooring, or anything else the parts may contact, with newspaper or cloth. rubber pad (4) Tools Required for Assembly: Phillips Screwdriver Wrenches (provided) poly bag TO INSTALL YOUR HYDRAULICS RESISTANCE LEVELS NOTE: There are 4 levels of resistance on the unit. Begin exercising at Level 1 (zero resistance) and slowly advance to the next level when the current level becomes too easy. The levels increase as you move the pin towards you to the next position. Zero Resistance Level 1 a. Fasten mounting brackets to the outside edges of the left and right foot tubes using (2) hex bolts, (2) washers and (2) nylon nuts. Tighten bolts with wrenches provided. b. Mount left hydraulic to left swing arm using (1) spring, (1) M12 washer, (2) rubber pads, (1) M12 washer (1) M8 washer, (1) nut, and (1) nut cap. rubber pad washer Note: the bottom of (M12) washer (M12) the hydraulic must washer (M8) have the pin facing nut the swing arm. cap spring nut To familiarize yourself with the parts, lay them out on the floor as shown. Cables should lay on top of the frames (be careful you do not tangle cables with swing arms). handlebars axle tube large washers frame plates end caps fastener pack c. Mount right hydraulic mounting bracket foot tube nut washer left swing arm M8 x 70mm hex bolts left side shown Repeat on right side. to right swing arm using (1) spring, (1) M12 washer, (2) rubber pads, (1) M12 washer, (1) M8 washer, (1) nut and (1) nut cap. Note: the bottom of the hydraulic must have the pin facing the swing arm. left frame right frame M6 x 40mm Phillips bolt (4) (attaches end caps to frame) left swing arm L inside of unit outside of unit pin Level 2 Level 3 Level 4 water bottle and holder left swing arm left right base base frame frame cross tube right swing arm M10 x 95mm hex bolt (4) and spring washer (attaches frame plate & cross tube to base frame) M8 x 25mm hex bolt (2), spring washer and washer (attaches axle tube to frame) wrench (2) If you do not wish to use the hydraulics, remove the clips and move the hydraulics into the zero resistance slot. Replace both clips. foot platform electronics a. Base Frame Assembly First, remove the 6, M8 x 25mm bolts and spring washers on the left and right base frames marked L and R with the arrows toward the front. Second, use 4 of the M8 x 25mm bolts, 2 on each end, to attach the cross tube to the top of the base frame. d. Pull left hydraulic down to allow pin to pass through resistance hole in mounting bracket. For ease of assembly, raise foot platform slightly so pin can reach mounting bracket. e. Lock clip onto hydraulic pin. Repeat Steps d and e on right side. Third, attach the frame plates to each side of the base frames using (4) M10 x 95mm hex bolts and spring washers from the fastener pack. These bolts also secure the base frame to the cross tube. Tighten bolts. clip in zero resistance remove 6 M8 x 25mm bolts from right base b. Lying Out Swing Arms replace 2 M8 x 25mm bolts to attach cross tube Move the left and right swing arms to the center of the frame assembly as shown. Make sure the cables lay on the top of all pieces. M10 x 95mm hex bolts front foot platform tube remove 6 M8 x 25mm bolts from left base replace 2 M8 x 25mm bolts to attach cross tube frame plate left frame right frame cross tube pin clip right base frame mounting bracket M10 x 95mm hex bolts frame plate left base frame left swing arm right swing arm ©2003, ©2004 and ©2005 Fitness Quest ® Inc. All rights reserved. Gazelle Power PlusTM is a trademark of Fitness Quest® Inc. left frame front c. Left Frame/Swing Arm Assembly Raise the left frame (marked with the L and arrow facing the front) and secure it onto the left base frame using (4) of the M8 x 25mm hex bolts and spring washers you removed in step a. When tightening these bolts, you can use the wrenches provided in either the fastener pack or the hydraulics fastener pack ­ whichever works best for you. Electronics Assembly Step 1: Remove the two small screws from the bottom of the electronics with the screwdriver provided. Insert the two "AAA" batteries in the top housing. Step 2: Attach the bottom housing with the large bolt provided in the bag with the batteries as shown. Step 3: From the front of the unit, place the top housing onto the bottom housing and replace the two small screws you removed in Step 1 as shown. Step 1 Step 2 view as if you are using the unit Step 3 M8 x 25mm hex bolt and spring washer left base frame Remove the two small screws left swing arm axle tube right swing arm d. Axle Tube Assembly Raise the left swing arm up to the top of the left frame. Slip the axle tube through the swing arm from the right. Make sure the arrow on the axle tube is pointing left and the notch on the end of the axle tube is down. IMPORTANT: Slip a large washer onto the axle between the swing arm and the left frame before inserting the axle tube into the left frame. Slide the axle tube through the left frame. Gently turn the axle tube back and forth until you feel the notch "catch" in place. This will tell you that the axle tube is locked into place. Secure the axle tube with a M8 x 25mm hex bolt, spring washer and washer from your fastener pack. right swing arm right frame insert screw reinsert the two small screws large washer axle tube with notch down arrow on axle pointing left left swing arm left frame M8 x 25mm hex bolt, spring washer and washer Handlebar Assembly Remove the bolts and washers from the handlebars. Slide the handlebars into swing arms as shown. On the front side of the unit, align the holes and insert bolts with washers. Tighten with the wrench provided. Attaching the End Caps and Water Bottle Holder Determine which side of your unit you want the water bottle (shown on the left side here). M6 x 40mm phillips bolts large washer M8 x 25mm hex bolt and spring washer e. Right Frame/Swing Arm Assembly Raise the right swing arm and slide it onto the axle tube. Slide the other large washer onto the axle tube between the right swing arm and the right frame. Now raise and slide the right frame (marked with the R and the arrow facing the front) onto the axle tube. As you did before, gently move the axle tube forward and backwards until the notch "catches" in place while pushing the right frame on. Secure everything onto the axle tube with the M8 x 25mm hex bolt, spring washer and washer that is left from your fastener pack. tab end cap front view Attach the end cap onto the frame using a M6 x 40mm Phillips bolt in the lower hole only. Align the water bottle holder on the end cap so the tab on the back of the holder fits into the bottom hole of the end cap. Secure the water bottle in place with an M6 x 40mm Phillips bolt. Attach the other end cap with (2) M6 x 40mm Phillips bolts. view as if stepping on unit front right base frame Slip the right frame onto the base frame assembly and secure it using the M8 x 25mm hex bolts and spring washers you removed in step a.