What would you like to do ? Help us find the most requested user's guides Upload your
user manual Search for a user manual Register Login and access your manuals Reset your password

	Browse all user guides
	The FLUKE 2063513 product forum
	Upload your user manual
	Sign-up Log in
	Help us find the most requested user's guides
	Include the add-on to download manuals from your site, forum or blog
	Frequently Asked Questions
	Contact Diplodocs team
ALL GUIDES BY CATEGORY Domestic Appliance TV & Audio Car & Motorcycle Phone Computer Camera & Video Music Sport Gardening & Housekeeping Video Game & Software Jewelry & Watch Baby & Toys Hygiene & Health Other

® 16 Multimeter with Temperature Instruction Sheet P Read First: Safety Information To ensure that the meter is used safely, follow these instructions: · Do not use the meter if the meter or test leads appear damaged, or if you suspect that the meter is not operating properly. · Disconnect the live test lead before disconnecting the common test lead. · When using the probes, keep your fingers behind the finger guards on the probes. · Do not use the V·Check mode to measure voltages in circuits that could be damaged by this mode's low input impedance (2 k). · Turn off power to the circuit under test before cutting, desoldering, or breaking the circuit. Small amounts of current can be dangerous. · Do not apply more than 600V rms between a meter terminal and earth ground. · Use caution when working with voltages above 60V dc or 30V ac rms. Such voltages pose a shock hazard. PN 2063513 December 2002 Rev.1, 9/04 2002,2004 Fluke Corporation. All rights reserved. Printed in China Symbols Press button. Press button to switch between modes. Double insulation. Manual ranging mode. ip14i.eps Automatic Range Selection The meter defaults to autoranging when you turn it on. The 4000 mV range can be entered only with manual range selection. Manual Range Selection 16 MULTIMETER OFF CAT 600V COM + To return to autoranging, press for 2 seconds, or change the measurement mode. ip15i.eps Battery Saver If the meter is ON but inactive and not connected to voltage for more than 45 minutes, the display goes blank to preserve battery life. To resume operation, press any button. Battery Saver is disabled in MIN/MAX record mode. AC and DC Voltage Also refer to V·Check. Volts AC Input Impedance 5 M 50 Hz to 400 Hz 16 MULTIMETER Volts DC Input Impedance 10 M 16 MULTIMETER AC DC 4000 mV 4V 40V OFF 400V 600V OFF V AC / DC CAT V AC / DC CAT 600V 600V COM + COM + ip01i.eps Resistance and Continuity eR Turn off circuit power before testing. Also refer to V·Check. Resistance 16 MULTIMETER Continuity 16 MULTIMETER 16 MULTIMETER Mk OFF A CAT V¥Check OFF 600V TEMPERATURE COM + Low Impedance V¥Check V¥Check OFF A CAT V¥Check A CAT 600V TEMPERATURE 600V TEMPERATURE COM + COM + Short Open ip02i.eps <25 Detects shorts and opens 250 µS. W V·Check If a dc or ac voltage greater than about 4.5V is present across the inputs when the meter is set to R, G, or e, the meter switches automatically to dc or ac voltage mode (V·Check mode). W Warning Repetitive transients on a dc bus will cause V·Check to select ac volts, even though a hazardous dc voltage may be present. To avoid a misleading display and possible electric shock, manually select the proper volts function for measurements on these circuits. When V·Check is activated, the meter has low input impedance (LoZ) 2 k. This load can alter the voltages in electronic control circuits. Do not use V·Check to measure voltage in circuits that could be damaged by a 2 k load. Hint: V·Check can be effectively used to eliminate "ghost" voltages. 16 MULTIMETER If AC detected If DC detected Meter puts 2 k load on circuit. Disable and re-enable V·Check For , and , Disables V·Check and locks meter in selected mode. 2 sec OFF A CAT V·Check 600V TEMPERATURE COM + or Re-enables V·Check or or ip09i.eps Temperature 16 MULTIMETER F C OFF A CAT V·Check 600V TEMPERATURE COM + 80BK Integrated Temperature Probe (Type K) Vent or Pipe ip19f.eps Note correct connector polarity. To meet stated accuracy, the 80BK temperature adapter must be at the same temperature as the meter. W Warning To avoid possible electric shock, DO NOT apply thermocouple tip to any conductor that is greater than 30V AC, 42.4V pk, or 60V DC to earth. Capacitance E Turn off circuit power; then disconnect and discharge the capacitor before measuring capacitance. 16 MULTIMETER If the capacitor requires more discharging, diSC is displayed while the capacitor discharges. OFF A CAT V·Check 600V TEMPERATURE COM + 1 µF 10 µF 100 µF 10,000 µF + ip05i.eps Note correct probe polarity for polarized capacitors. Microamps µA Range 0 to 200 µA 16 MULTIMETER µA AC µA DC OFF A CAT V·Check 600V TEMPERATURE COM + Flame sensor probe Control module ip20i.eps Example: Flame rectification circuit. To measure flame rectification circuits: 1. 2. 3. 4. Turn function switch to far right position. Push select button 3 times to select µA. Connect meter between flame sensor probe and control module. Turn heating unit on and record µA measurement. Diode Test G Turn off circuit power before testing. For best results diodes should be measured out of circuit. Also refer to V·Check. Good Diode 16 MULTIMETER Typical voltage for silicon diode 16 MULTIMETER Low Impedance V·Check OFF A CAT V·Check OFF A CAT V·Check 600V TEMPERATURE 600V TEMPERATURE COM + COM + Single beep ip03i.eps Forward Bias Bad Diode 16 MULTIMETER Reverse Bias 16 MULTIMETER OFF A CAT V·Check OFF A CAT V·Check 600V TEMPERATURE 600V TEMPERATURE COM + COM + or ip04i.eps Shorted Open MIN MAX µF (Records the lowest and highest measurements) V·Check, autoranging, and Battery Saver are disabled. Put the meter in the proper range before entering MIN MAX. When the reading changes more than about 50 digits, the meter gives a short beep. When a new minimum or maximum is recorded, the meter gives a long beep. Enter Present Reading with MIN MAX Input Change Alert TM Maximum Reading 2 sec To Exit Minimum Reading ip10i.eps MIN MAX with Elapsed Time µF Records the hours and minutes between when MIN MAX was entered and the last high and low was recorded. OL is displayed for times longer than 99:59. To enable the MIN MAX timer, hold down M while turning the rotary switch from OFF to either measurement mode. Enter MIN MAX. View Present Reading Maximum Reading Maximum Reading Elapsed Time 2 sec Minimum Reading Elapsed Time Minimum Reading Exit MIN MAX ip11i.eps To disable the beeper for all modes, hold down r for 2 seconds while turning the meter on. Disabling the Beeper Continuity Capture To set up the meter to capture intermittent shorts and opens, turn the switch to GR, connect the leads to the circuit; then press M. ip12i.eps Captures transitions longer than 250 µs (1/4000th of a second). Transitions after the first transition cause the meter to beep, but the display does not change. To reset the display to the current condition, press M. To exit, press M for 2 seconds, or change the measurement mode. Maintenance Clean the case with a damp cloth and detergent. Do not use abrasives or solvents. Battery Replacement Remove the test leads before disassembling the case. Replacement Parts Fluke TL-75 (Double-insulated leads) PN 855705 80BK (Integrated Temperature Probe) PN 1273124 Service and Parts This meter should be serviced only by a qualified service technician. To locate an authorized service center, call: USA: 1-888-99-FLUKE (1-888-993-5853) Canada: 1-800-36-FLUKE (1-800-363-5853) Europe: +31 402-675-200 Japan: +81-3-3434-0181 Singapore: +65-738-5655 Anywhere in the world: +1-425-446-5500 Or, visit Fluke's Web site at www.fluke.com. C O M 60 0V + + ip13i.eps Specifications Accuracy is specified for a period of one year after calibration, at 18°C to 28°C (64°F to 82°F) with relative humidity to 90%. AC conversions are ac-coupled, average responding, and calibrated to the rms value of a sine wave input. Accuracy specifications are given as follows: ±([% of reading] + [number of least significant digits]) Function Temperature Range -10°C to 400°C 14°F to 752°F Resolution 0.1°C or 0.2°F 0.1°C or 0.2°F Accuracy ±(1.0% + 0.8°C) typical ±(1.0% + 1.5°F) typical ±(5.0% + 1.5°C) typical ±(5.0% + 3.3°F) typical Accuracy (Type K Thermocouple) -40°C to -10°C -40°F to 14°F Error does not include Type K Thermocouple errors. Function Range 4000 mV 4.000V 40.00V 400.0V 600V 1 4000 mV 4.000V 40.00V 400.0V 600V 400.0 4.000 k 40.00 k 400.0 k 4.000 M 40.00 M 1.000 µF 10.00 µF 100.0 µF 10000 µF 1 Resolution 1 mV 0.001V 00.01V 000.1V 1V 1 mV 0.001V 00.01V 000.1V 1V 0.1 0.001 k 0.01 k 0.1 k 0.001 M 0.01 M 0.001 µF 0.01 µF 0.1 µF 1 µF ±(1.9% + 3) ±(1.9% + 3) f ±(1.9% + 3) (50 to 400 Hz) ±(1.9% + 3) ±(1.9% + 3) ±(0.9% + 2) ±(0.9% + 2) ±(0.9% + 1) E ±(0.9% + 1) ±(0.9% + 1) ±(0.9% + 2) ±(0.9% + 1) ±(0.9% + 1) ±(0.9% + 1) ±(0.9% + 1) ±(1.5% + 3) ±(1.9% + 2) ±(1.9% + 2) ±(1.9% + 2) | 1000 µF ±(1.9% + 2) >1000 µF ±(10% + 90) typical ML 2.000V 0.001V ±(1.9% + 2)2 1. The 4000 mV range can be entered only in manual range mode. Use the 4000 mV range with accessories. 2. The beeper is guaranteed to come on at <25 and turn off at >250. The meter detects opens or shorts 250 µs. Function Range 0 to 200 µA 0 to 200 µA Resolution 0.1 µA 0.1 µA Accuracy ±(2% + 3 counts) ±(1% + 2 counts) Burden Voltage <5 mV/µA <5 mV/µA N (50 Hz to 400 Hz) M Function f E Overload 1 Protection 600V rms 600V rms Input Impedance (Nominal) >5 M <100 pF V·Check and LoZ = >2 k <200 pF (ac coupled)2 >10M <100 pF V·Check and LoZ = >2 k <200 pF2 Common Mode Rejection Ratio (1 k Unbalanced) Normal Mode Rejection f E 600V rms 600V rms >60 dB at dc 50 or 60 Hz >100 dB at dc, 50 or 60 Hz Open Circuit Test Voltage >50 dB at 50 Hz or 60 Hz Full Scale Voltage To 4.0 M 40 M <450 mV dc <1.5V dc 2.400V dc J L 600V rms 600V rms <1.5V dc 2.4-3.0V dc Short Circuit Current J L 600V rms 600V rms <500 µA 0.95 mA (typical) 1. 3 x 106 V Hz maximum 2. 2 k input impedance up to 50V. Impedance increases with input voltage to >300 k at 600V. MIN MAX Recording Accuracy and Response Time Specified accuracy of the measurement function ±12 digits in dc for changes >200 ms in duration (±40 digits in ac). Typical 100 ms response to 80%. Example 1: This would mean ±1.2° when recording temperature. Example 2: This would mean ±1.2 µA when recording µA or ±12A if used with a dc amp probe (with a mV input). MIN MAX Recording with Elapsed Time Elapsed Time 0 to 100 hours (99:59) Resolution 1 minute Accuracy 0.3% typical Maximum Voltage Between any Terminal and Earth Ground: Display: Operating Temperature: Storage Temperature: Temperature Coefficient: Relative Humidity: Battery Type: Battery Life: Shock: Vibration: Size (H x W x L): Weight: Safety: 600V rms 3 3/4-digits, 4000 counts, updates 4/sec -10°C to 50°C (14°F to 122°F) -30°C to 60°C (-22°F to 140°F) indefinitely (to -40°C (-40°F) for 100 hrs) (.1 x specified accuracy)/°C (<18°C or >28°C) 0% to 90% (-10°C to 35°C; 14°F to 95°F) 0% to 70% (35°C to 50°C; 95°F to 122°F) 9V, NEDA 1604 or IEC 6F22 650 continuous hours with alkaline 450 continuous hours with carbon-zinc 1 meter drop 6 sides. Class II vibration MIL-PRF-28800F 3.46 cm x 7.05 cm x 14.23 cm (1.35 in x 2.75 in x 5.55 in) 286g (10 oz) Designed to Protection Class II requirement of UL3111, ANSI/ISA-S82, CSA C22.2 No 231, and VDE 0411, and IEC 1010 overvoltage Category III (CAT III, 600 Volts). Complies with FCC Part 15, Class B, and VDE 0871B. Trademark of TÜV Product Services. Complies with EN 61010-1: 1993. EMI Regulations: Certifications: P$ TUV, UL and VDE LIMITED WARRANTY & LIMITATION OF LIABILITY Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is three years and begins on the date of shipment. Parts, product repairs and services are warranted for 90 days. This warranty extends only to the original buyer or end-user customer of a Fluke authorized reseller, and does not apply to fuses, disposable batteries or to any product which, in Fluke's opinion, has been misused, altered, neglected or damaged by accident or abnormal conditions of operation or handling. Fluke warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Fluke does not warrant that software will be error free or operate without interruption. Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is available if product is purchased through a Fluke authorized sales outlet or Buyer has paid the applicable international price. Fluke reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased in one country is submitted for repair in another country. Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is returned to a Fluke authorized service center within the warranty period. To obtain warranty service, contact your nearest Fluke authorized service center or send the product, with a description of the difficulty, postage and insurance prepaid (FOB Destination), to the nearest Fluke authorized service center. Fluke assumes no risk for damage in transit. Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB Destination). If Fluke determines that the failure was caused by misuse, alteration, accident or abnormal condition of operation or handling, Fluke will provide an estimate of repair costs and obtain authorization before commencing the work. Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges (FOB Shipping Point). THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, WHETHER ARISING FROM BREACH OF WARRANTY OR BASED ON CONTRACT, TORT, RELIANCE OR ANY OTHER THEORY. Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision. Fluke Corporation Fluke Europe B.V. P.O. Box 9090 P.O. Box 1186 Everett WA 5602 B.D. Eindhoven 98206-9090 The Netherlands 5/94