FO T IN TA N ce P O R ore use feren I M bef re re ad futu Re for tain & re IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www.flymo.com eop.customer.services@electrolux.co.uk ¤ 1 Carton Contents Switch levers handguard instruction manual electric mains cable with moulded plug cable holder blade cover/storage holder IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this Hedgetrimmer can be dangerous! This Hedgetrimmer can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this Hegetrimmer. The operator is responsible for following the warning and safety instructions in this manual and on the Hedgetrimmer. Explanation of Symbols on the Easi-Trim 420, 450s, 530, 530s. Do not use in the rain or leave the Hedgetrimmer outdoors while raining. Warning. Read the user instructions carefully to make sure you understand all the controls and what they do. The use of eye protection is recommended. Switch off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Keep the cable away from the blade. 2 General 1. Never allow children or people unfamiliar with these instructions to use the Hedgetrimmer. Local regulations may restrict the age of the operator. 2. Only use the Hedgetrimmer in the manner and for the functions described in these instructions. 3. Never operate the Hedgetrimmer when you are tired, ill or under the influence of alcohol, drugs or medicine. 4. The operator or user is responsible for accidents or hazards occurring to other people or their property. Electrical 1. The British Standards Institute recommend the use of a Residual Current Device (R.C.D.) with a tripping current of not more than 30mA. Even with a R.C.D. installed 100% safety cannot be guaranteed and safe working practice must be followed at all times. Check your R.C.D. every time you use it. 2. Before use, examine cable for damage, replace it if there are signs of damage or ageing. 3. Do not use the Hedgetrimmer if the electric cables are damaged or worn. 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your electric cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your Hedgetrimmer. 6. Keep cable away from the cutting area. 7. Never carry the product by the cable 8. Never pull on the cable to disconnect any of the plugs 9. Do not pull cable around sharp objects. 10. Always switch off at the mains before disconnecting any plug, cable connector or extension cable. 11. Switch off, remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage. Do not repair a damaged cable, replace it with a new one. Use only Flymo replacement cable. 12. Always wind cable carefully, avoiding kinking. 13. Use only on AC mains supply voltage shown on the product rating label. 14. Our products are double insulated to EN60335. Under no circumstance should an earth be connected to any part of the product. Preparation 1. Always wear suitable clothing, gloves, and stout shoes. The use of safety glasses is recommended. Do not wear loose clothing or jewellery which can be caught in moving parts. 2. Thoroughly inspect the area where the Hedgetrimmer is to be used and remove all wires and other foreign objects. 3. Before using the machine and after any impact, check for signs of wear or damage and repair as necessary. 4. Always ensure the hand guard supplied is fitted before using the Hedgetrimmer. Never attempt to use an incomplete Hedgetrimmer or one with an unauthorised modification. Use 1. Use the Hedgetrimmer only in daylight or good artificial light. 2. Avoid operating your Hedgetrimmer on a wet hedge, where feasible. 3. Know how to stop the Hedgetrimmer quickly in an emergency. 4. Never hold the Hedgetrimmer by the guard. 5. Never operate the Hedgetrimmer with damaged guards or without guards in place. 6. Remove plug from mains before passing Hedgetrimmer to another person. 7. Avoid operating while people especially children are nearby. 8. Whilst using the Hedgetrimmer always be sure of a safe and secure operating position. 9. Keep hands and feet away from the cutting means at all times and especially when switching on the motor. 10. Do not use stepladders whilst operating the Hedgetrimmer. 11. Remove the plug from the mains :before leaving the Hedgetrimmer unattended for any period; before clearing a blockage; before checking, cleaning or working on the appliance; if you hit an object. Do not use your Hedgetrimmer until you are sure that the entire Hedgetrimmer is in a safe operating condition; if the Hedgetrimmer starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury; before passing to another person. Maintenance and storage 1. Keep all nuts, bolts and screws tight to be sure the Hedgetrimmer is in safe working condition. 2. Replace worn or damaged parts for safety. 3. Be careful during adjustment of the Hedgetrimmer to prevent entrapment of the fingers between moving blades and fixed parts of the machine. 4. After use the Hedgetrimmer should be stored using the blade cover/storage holder provided. 3 CABLES IMPORTANT · Use only 1.00mm2 size cable up to 30 metres length maximum. 3. IMPORTANT! E L F U S E Maximum rating : 1.00mm2 size cable, 10 amps 250 volts AC. · THE EASI-TRIM IS SUPPLIED WITH CABLE WIRED DIRECTLY INTO THE PRODUCT. Flymo Mains Cables and Extension Cables are available from your local Electrolux Outdoor Products Approved Service Centre. Do not wire an extension cable directly to your product yourself. Please contact your local Electrolux Outdoor Products Approved Service Centre for further information on the connectors and kits available. Only use extension cables specifically designed for outdoor use. RED OR BROWN 1. BLACK OR N BLUE 2. 3. CONNECTORS IMPORTANT · Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. 4. 5. The wires in the mains lead are coloured in accordance with the following code: BLUE NEUTRAL BROWN LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. It is important that the outer sheath is clamped correctly into the 3-pin plug. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. A 13 Amp fuse must be fitted to the Mains Plug. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. · 6. 7. MAINS PLUG REPLACEMENT IMPORTANT · If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. No earth required. Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product. Ensure the mains voltage suits your product 1. 2. If your product is hard wired i.e. nondetachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. 4 Preparation Instructions Fitting the Cable Holder to Your Hedgetrimmer (A) and (B) A 1. Insert T-shaped hooks of cable holder into Tshaped holes on the underside of your Hedgetrimmer. (See Fig. A) B 2. Secure by pulling the cable holder, in the direction shown, away from the Hedgetrimmer, blades until it locks into position. (See Fig. B) Starting and Stopping Before starting your Hedgetrimmer. C D 1. Form a loop in mains cable and push the loop through the hole in the cable holder as illustrated in Fig. C. To secure, position the loop around the hook as illustrated in Fig. D. Connect to mains and switch on Remove blade cover/storage holder as illustrated in Fig. E. 2. 3. 4. E To start your Hedgetrimmer (F) 1. 2. There are two switch levers fitted to your Hedgetrimmer. Both switch levers need to be held in the operating position (See Fig F) for the product to start. F To stop your Hedgetrimmer (G) G · 1. Move Hedgetrimmer away from cutting area before stopping. To stop, release one of the switch levers. 5 How to Use H How to Use your Hedgetrimmer 1. Inspect area to be cut before each use remove objects which can be thrown or become entangled in the cutting blades. 2. Always keep the Hedgetrimmer in front of your body. Hold handle firmly with both hands and stand in a secure and stable position. 3. Allow the cutting blades to reach full speed before entering the material to be cut. 4. Always work going away from people and solid objects such as walls, large stones, trees, vehicles etc. 5. If blade stalls, immediately stop the Hedgetrimmer. Disconnect the Hedgetrimmer from the power source and clear jammed debris from the cutting blades. Inspect blades and repair or replace as needed. Top Cutting (H) Use a wide sweeping motion. See Fig. H. A slight downward tilt of the cutting blades in the direction of motion gives the best cutting results. Side Cutting (J) When trimming the sides of the hedge, begin at the bottom and cut upwards (See Fig. J), tapering the hedge inward at the top. This shape will expose more of the hedge, resulting in more uniformed growth. J Caring for your Hedgetrimmer K Cleaning (K) · 1. 2. USE GLOVES Using a soft brush - remove debris from all air intakes and cutting blade. Wipe over surface of your hedgetrimmer with a dry cloth. IMPORTANT Never use water for cleaning your hedgetrimmer. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. · 6 Caring for your Hedgetrimmer Lubricating the Cutting Blade For easier operation and longer life, lubricate the cutter blades before and after use. Apply the oil so that it runs between the two blades. See Pic L. At the end of the Cutting Season. 1. Clean your Hedgetrimmer thoroughly. 2. Check that all nuts and bolts are tight. 3. Visually inspect the Hedgetrimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement. To store your Hedgetrimmer · The Hedgetrimmer blade cover/storage holder is provided with 2 hanging slots for storing the Hedgetrimmer on the wall. (See Pic M) · Ensure the blade cover is fitted before storage. · Remove cable from cable holder before storage. 1. The use of 2 number 10 screws (40mm in length) and the appropriate wall fixing plugs is recommended 2. Drill 2 holes 48mm horizontally apart. 3. Fit wall plugs. 4. Fit screw ensuring enough length is available for secure location into hanging slot. 5. Store as illustrated in Pic N. L M N Store in a dry place where your hedgetrimmer is protected from damage. Fault Finding Hints Fails to Operate 1. Is the Power Turned On? 2. Check the fuse in the plug, if blown replace. 3. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Cutting blade stops under load 1. Cut at a slower pace. 2. If cutting blade still stops under load? Disconnect from the mains electricity supply and consult your local approved Service Centre. Fails to stop when one switch lever is released. Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Poor cut quality 1. Ensure the product is being used correctly (see How to Use) 2. Ensure blades are free from trapped debris 3. Damaged Blades? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Excessive Vibration Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Environmental Information Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products' life. · Pack ...