FO T IN AN nce O RT e use M P efor efere I er ad b for futur Re tain & re AT I O RM N For all customer enquiries or for replacement parts, contact:- 01325 300303 www.flymo.com eop.customer.services@electrolux.co.uk 1 Carton Contents adjustable handle trigger 2 handle knobs mode indicator 2 handle bolts Air inlets debris bag frame adjustable shoulder harness debris bag cutting lines instruction manual nozzle IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 Safety If not used properly this Gardenvac can be dangerous. The warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warnings and instructions in this manual and on the product. Explanation of Symbols on the Gardenvac EVERY TIME YOU USE YOUR GARDENVAC Switch off and disconnect from the mains electricity supply BEFORE fitting cutting line to cutting head & clipping into place and BEFORE REMOVING cutting line. Switch off and disconnect from the mains electricity supply BEFORE FITTING fully assembled debris bag to product and BEFORE REMOVING fully assembled debris bag from product. The use of eye protection is recommended. Warning Read the user instructions carefully to make sure you understand all the controls and what they do. Do not operate in the rain or leave the product outdoors while it is raining. Switch off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Keep bystanders away. 2 BEFORE USING YOUR GARDENVAC FOR THE FIRST TIME 1 Assemble debris bag to bag frame. NEVER CONNECT THE PRODUCT TO THE MAINS ELECTRICITY SUPPLY UNTIL THE FULLY ASSEMBLED DEBRIS BAG IS FITTED CORRECTLY General 1. Never allow children or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator. 2. Only use the product in the manner and for the functions described in these instructions. 3. Never operate the product when you are tired, ill or under the influence of alcohol, drugs or medicine. 4. The operator or user is responsible for accidents or hazards occurring to other people or their property. Electrical 1. The British Standards Institute recommend the use of a Residual Current Device (R.C.D.) with a tripping current of not more than 30mA. Even with a R.C.D. installed 100% safety cannot be guaranteed and safe working practice must be followed at all times. Check your R.C.D. every time you use it. 2. Before use, examine cable for damage, replace it if there are signs of damage or ageing. 2 3. Do not use the product if the electric cables are damaged or worn. 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your electric cable must be uncoiled, coiled cables can overheat and reduce the efficiency of the product. 6. Do not pull cable around sharp objects. 7. Always switch off at the mains before disconnecting any plug, cable connector or extension cable. 8. Switch off, remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage. Do not repair a damaged cable, replace it with a new one. Use only genuine replacement cable. 9. Never carry the product by the cable. 10. Never pull on the cable to disconnect any of the plugs 11. Always wind cable carefully, avoiding kinking. 12. Use only on AC mains supply voltage shown on the product rating label. 13. Our products are double insulated to EN60335. Under no circumstance should an earth be connected to any part of the product. Preparation 1. Always wear suitable clothing, gloves, and stout shoes. 2. The use of eye protection is recommended. 3. The use of ear protection is recommended. 4. To prevent dust irritation, the wearing of a face mask is recommended. 5. Do not wear loose clothing or jewellery that can be drawn into the air inlet. 6. Do not wear clothing with attachments, i.e. toggles or drawstrings that can be drawn into the air inlet. 7. Inspect your product before each use, especially the parts of the cutting head. Replace cutting line if worn or damaged. 8. Do not use if any part is damaged or broken or if any of the screws are loose. Have it repaired by an authorised repairer. CABLES IMPORTANT · Use only 1.00mm2 size cable up to 40 metres length maximum. Maximum rating : 1.00mm2 size cable, 10 amps 250 volts AC. · THE GARDENVAC IS SUPPLIED WITH CABLE WIRED DIRECTLY INTO THE PRODUCT. 1. Flymo Mains Cables and Extension Cables are available from your local Electrolux Outdoor Products Approved Service Centre. 2. Do not wire an extension cable directly to your product yourself. Please contact your local Electrolux Outdoor Products Approved Service Centre for further information on the connectors and kits available. 3. Only use extension cables specifically designed for outdoor use. CONNECTORS IMPORTANT · Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. · All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT IMPORTANT · If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. 9. Always check your product is in a safe operating condition before use. Use 1. Use the product only in daylight or good artificial light. 2. Do not use the product when it is raining or in damp and wet areas. 3. Never use the product in or near water or ponds. 4. Know how to stop the product quickly in an emergency. 5. On slopes, be extra careful of your footing and wear non-slip footwear. 6. Never pick up or carry the product by the cable. 7. Keep children, pets and bystanders at a safe distance when using your product. 8. Keep long hair away from air inlet. 9. Keep all inlets clear of debris. 10. Always remain alert. 11. Do not attempt to use your product without the fully assembled debris bag fitted. 12. Never blow debris in the direction of bystanders. 13. Do not overreach. Keep proper footing and balance at all times. 14. The cutting head and cutting line continue to rotate after your product has been switched off. 15. Remove the plug from the mains :before removing or replacing cutting line; before removing or replacing fully assembled debris bag; before leaving the product unattended for any period; before clearing a blockage; before checking, cleaning or working on the appliance; if the product starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury. Maintenance and storage 1. Keep all nuts, bolts and screws tight to be sure the product is in a safe working condition. 2. Replace worn or damaged parts for safety. 3. After use the product should be stored in a safe place where it is protected from damage. 4. Inspect the collection bag regularly. If the collection bag becomes worn or damaged, replace. 1. No earth required. Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product. 2. Ensure the mains voltage suits your product 3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE NEUTRAL BROWN LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. 4. It is important that the outer sheath is clamped correctly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 13 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. If your product is hard wired i.e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. 3 A Assembly Instructions C B D To Attach Debris Bag to Bag Frame With bag frame on the ground:1. Fit first two holes on the plastic trim of the debris bag to the first two location points on the front of the bag frame (where debris fin is attached). (A) 2. Fit next hole on the plastic trim to next location point on bag frame. (B) 3. ...until all holes on the plastic trim of the debris bag are securely located to bag frame. (C) · ENSURE THE DEBRIS BAG IS FITTED SECURELY TO THE BAG FRAME. To Fit the Cutting Line to the Cutting Head (D) · Switch off and disconnect from the mains electricity supply BEFORE removing or fitting the cutting line. · Handle the cutting line with care - sharp edges can cause injury. 1. Place the cutting line into the slot in the cutting head and click into place as illustrated in Figure D. · Ensure the cutting line is correctly located. · ONLY USE CUTTING LINE SPECIFIED FOR THIS PRODUCT. SEE PRODUCT RATING LABEL FOR MODEL DETAILS E 4 2 2 1 To Fit Assembled Debris Bag To Product (E) · · Switch off and disconnect from the mains electricity supply BEFORE REMOVING OR REPLACING the fully assembled debris bag. The cutting head and cutting line continue to rotate after your Gardenvac has been switched off. 2 IMPORTANT: Do not squeeze the trigger when fitting the debris bag (E1) 1. 2. 3. Ensure debris fin is horizontal (E2) as illustrated in fig E. Locate bag frame into clip on the underside of product. (E3). Lift handle towards product until bag latch locates and click into place. (E4) 3 1 debris fin F To Remove Debris Bag From Product (F) 1. 2. 3. Gently press bag latch (F1) down. See fig F. Lower handle of bag frame away from product. Move bag frame forward. 1 4 G Assembly instructions H Fitting the Handle Bolt (G) 1. Place handle bolt into the location slot on the product and slide into place.(G). 2. Repeat on the other side. Fitting the Handle (H) 1. Locate handle onto handle bolts on each side of the product. 2. Secure handle by turning handle knobs clockwise. (H) 3. The handle can be adjusted by turning handle knobs 3 full turns anti-clockwise, moving handle to position required and re-securing handle as described in 2. Fitting The Shoulder Harness (J) & (K). 1. Thread strap through the slots in the handle.(J) 2. Thread strap through the buckle. See fig J. Adjust as required to ensure the shoulder harness is in the most comfortable position. See fig. K. J Buckle K How to Use WARNING The use of eye protection is recommended. The use of ear protection is recommended. To prevent dust irritation, the wearing of a face-mask is recommended. Never point your product at bystanders. Do not use your product in the rain. Do not leave your product outdoors while it is raining. IMPORTANT!: YOUR PRODUCT WILL NOT OPERATE UNTIL THE FULLY ASSEMBLED DEBRIS BAG AND FRAME ARE PROPERLY FITTED. BEFORE USE: ENSURE THERE ARE NO GAPS BETWEEN THE DEBRIS BAG AND THE PRODUCT. · The Gardenvac has 3 modes of operation. · These can be selected by moving the mode indicator to adjust the nozzle position for blow, vacuum or jet vacuum mode. · In vacuum and jet vacuum modes the product will shred leaves etc. L BLOW Position 1 - Blow Mode The Gardenvac will blow debris from patios, paths, driveways, lawns, bushes, borders etc. Using As A Blower 1. Select position 1 on the mode indicator. See fig L. 2. Point nozzle towards the ground. 3. To start squeeze trigger. 4. Stand back from debris to be cleared. 5. Point nozzle towards the debris and slowly approach. 6. To stop release trigger. M VACUUM Position 2 - Vacuum Mode In this position your product will pick up leaves, paper, rubbish, cans etc. IMPORTANT: REMOVE NYLON LINE BEFORE VACUUMING CANS Using As A Vacuum 1. Select position 2 on the mode indicator. See fig M. 2. Position nozzle slightly above the debris, squeeze the trigger and move slowly back and forth. 3. Do not force the nozzle into the debris as this will impair performance. 4. To stop release the trigger. 5 How to Use Con't N JET VACUUM Position 3 - Jet Vacuum Mode This position is intended to be used to collect debris which is damp or stubborn. It directs a small jet of air towards the ground which will loosen stubborn material. Using As A Jet Vacuum 1. Select position 3 on the mode indicator. See fig ...