FO T IN AN O RT e use ence I M P befor refer ure ead r fut R n fo retai & IO M AT R N For all customer enquiries or for replacement parts, contact:- 01325 300303 www.flymo.com eop.customer.services@electrolux.co.uk ¤ 1 Carton Contents Height Adjust Nut (if applicable) Handle Knob Steady Handle NonHeight Adjust Bolt Nut (if applicable) Handle Knob Bolt Steady Handle Guard Guard Instruction Manual Electric Cable with moulded on plug Electric Cable with moulded on plug Scraper Tool (Multi-Trim 200 only) Instruction Manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 Safety Please note: This manual covers various products. Please read the user instructions carefully to fully identify, assemble and use the features that apply to your trimmer. If not used properly this trimmer can be dangerous! This trimmer can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this trimmer. The operator is responsible for following the warning and safety instructions in this manual and on the trimmer. Explanation of Symbols on the Multi Trim The use of eye protection is recommended to protect against objects thrown by the cutting line. Warning Read the user instructions carefully to make sure you understand all the controls and what they do. Keep others, including children, pets and bystanders outside the 10 metre hazard zone. Stop the trimmer immediately if you are approached. To avoid the possibility of electric shock, do not use in damp or wet conditions. 10m Switch off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Warning: The cutting line continues to rotate after the machine has been switched off. Electrical 1. The British Standards Institute recommend the use of a Residual Current Device (R.C.D.) with a tripping current of not more than 30mA. Even with a R.C.D. installed 100% safety cannot be guaranteed and safe working practice must be followed at all times. Check your R.C.D. every time you use it. 2. Before use, examine cable for damage, replace it if there are signs of damage or ageing. 3. Do not use the trimmer if the electric cables are damaged or worn. General 1. Never allow children or people unfamiliar with these instructions to use the trimmer. Local regulations may restrict the age of the operator. 2. Only use the trimmer in the manner and for the functions described in these instructions. 3. Never operate the trimmer when you are tired, ill or under the influence of alcohol, drugs or medicine. 4. The operator or user is responsible for accidents or hazards occurring to other people or their property. 360º 2 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your trimmer. 6. Keep the cable clear of the cutting area and obstacles at all times. 7. Do not pull cable around sharp objects. 8. Always switch off at the mains before disconnecting any plug, cable connector or extension cable. 9. Never pull on the cable to disconnect any of the plugs. 10. Switch off, remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage. Do not repair a damaged cable, replace it with a new one. Use only Flymo replacement cable. 11. Always wind cable carefully, avoiding kinking. 12. Use only on AC mains supply voltage shown on the product rating label. 13. Flymo trimmers are double insulated to EN60335. Under no circumstance should an earth be connected to any part of the trimmer. Preparation 1. While using your product always wear substantial footwear and long trousers. 2. Before using the machine and after any impact, check for signs of wear or damage and repair as necessary. 3. Inspect the area to be cut before each use. Remove all objects such as stones, broken glass, nails, wire, string etc, which can be thrown or become entangled in the trimmer head. 4. Check that the cutting head, spool and cap are fitted correctly. Use AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM MAINS AND KEEP FEET AWAY FROM THE SWITCH LEVER WHEN:- CLEANING AROUND THE INSIDE OF THE SAFETY GUARD, REMOVING OR REFITTING SPOOL CAP, MANUALLY FEEDING OR REPLACING NYLON LINE. 1. Use the trimmer only in daylight or good artificial light. 2. Avoid operating your trimmer in wet grass, where feasible. 3. Take care in wet grass, you may lose your footing. 4. On slopes, be extra careful of your footing and wear non-slip footwear. 5. Do not walk backwards when trimming , you could trip. Walk never run. 6. Keep cutting head below waist level. 7. Switch off before pushing the trimmer over surfaces other than grass. 8. Never operate the trimmer with damaged guards or without guards in place. 9. Never fit metal cutting elements. 10. Keep hands and feet away from the cutting means at all times and especially when switching on the motor. 11. Never pick up or carry a trimmer by the cable. 12. Do not lean over the trimmer guard - objects may be thrown by the cutting line. 13. Remove the plug from the mains : before leaving the trimmer unattended for any period; before clearing a blockage; before checking, cleaning or working on the appliance; if you hit an object. Do not use your trimmer until you are sure that the entire trimmer is in a safe operating condition.; if the trimmer starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury. Maintenance and storage 1. Keep all nuts, bolts and screws tight to be sure the trimmer is in safe working condition. 2. Replace worn or damaged parts for safety. 3. Only use the replacement cutting line specified for this product. 4. Only use replacement parts and accessories recommended by Electrolux Outdoor Products. 5. To avoid the risk of injury keep fingers and hands clear of the line cutter on the leading edge of the guard. 6. Inspect and maintain the trimmer regularly. Any repairs must be carried out by an authorised repairer. Cables IMPORTANT Use only 1.00mm2 size cable up to 30 metres length maximum. Maximum rating: 1.00mm2 size cable, 10 amps 250 volts AC. THE MULTI TRIM IS SUPPLIED WITH AN ELECTRIC MAINS CABLE WIRED DIRECTLY INTO THE PRODUCT. 1. Flymo Mains Cables and Extension Cables are available from your local Electrolux Outdoor Products Approved Service Centre. 2. Do not wire an extension cable directly to your product yourself. Please contact your local Electrolux Outdoor Products Approved Service Centre for further information on the connectors and kits available. 3. Only use extension cables specifically designed for outdoor use. CONNECTORS Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT · If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. 1. No earth required. Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product. 2. Ensure the mains voltage suits your product. 3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE NEUTRAL BROWN LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter `N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter `L' or coloured RED. 4. It is important that the outer sheath is clamped correctly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 5 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. If your product is hard wired i.e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. 3 Assembly Instructions A 3 1 Safety Guard Assembly (A), (B) & (C) · If you have a Multi Trim 200 your safety guard will be fitted with a wire guard as shown in figure J2. 1. Align the arrow on the top of the safety guard (A1) with the arrow on the side of the trimmer (A2). 2. Locate the safety guard (A3) over the cutting head (A4). Ensure the nylon line is fed through the hole in the safety guard as illustrated in fig A. Please note: Depending on which model you have purchased, your trimmer may be fitted with one line or two lines. 3. Push into location and turn safety guard in the direction illustrated in Fig B, until a click is heard and the safety guard is securely locked in position. · ENSURE THE SAFETY GUARD IS SECURELY IN PLACE BY ATTEMPTING TO TWIST GUARD. See fig C. 2 4 B C D handle knob E Steady Handle Assembly (D), (E) & (F) 1. Insert the nut into the handle knob. (if applicable). 2. Attach steady handle to product using bolt and handle knob as shown in Fig D. 3. To adjust steady handle to new position, loosen handle knob as shown in Fig E. and move handle to one of the three positions as shown in Fig F. 4. Re-tighten handle knob nut (if applicable) bolt F G H height adjust knob Height Adjustment (if fitted) If your trimmer is fitted with Height Adjust, follow the procedure below. 1. Loosen the height adjust knob. (fig G) 2. Adjust length of the handle to the most comfortable operating position (fig H). 3. Re-tighten the height adjust knob. Auto Line Feed System If you have a Multi Trim 200, it will be fitted with a wire guard as shown in figure J2. Please note: Depending on which model you have purchased, your trimmer may be fitted with one line or two lines. How the automatic line feed works (J) 1. When initially switching on the trimmer, a small length of line is fed out. 2. A `clattering' noise will be heard when the nylon line hits the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. · Make sure the motor is up to full speed before trimming or edging. 3. If the noise of the nylon line being cut cannot be heard, more line will need to be fed out. 4. To feed more line, it is first necessary to to allow the motor to stop completely, then re-start, allowing the motor to reach full speed. 5. Repeat step 4. until you hear the line hitting against the cutter. (Do not repeat this procedure more than 6 times) 6. If problems are experienced with the automatic line feed refer to Fault Finding Chart. J1 J2 Multi Trim 200 only line cutter wire guard line cutter 4 How to Trim and Edge WARNING: The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. Disconnect from the mains electricity supply before attempting any maintenance or adjustment. BEFORE USE: Make sure that the line is fed out (if 2 lines are fitted, make sure both are fed out). Make sure motor is up to full speed before trimming or edging. How to trim 1. Hold as illustrated in Fig K. 2. To start, squeeze the switch lever. 3. Cut with nylon line at an angle using the tip. See Fig L 4. Swing trimmer in and out of the cutting area taking small cuts (M) 5. Line is fed out automatically every time the trimmer head stops rotating and returns to operating speed. · Extra line can be fed out manually as described on page 5. 6. To stop your trimmer release the switch lever. How to edge 1. To convert to edging mode, depress locking button and twist head anti-clockwise until arrow lines up with "EDGE". An audible "click" will confirm that the head is locked. Ensure the button has returned to its original position. See Fig N. 2. Hold as illustrated in Fig K. 3. To start, squeeze the switch lever. 4. Rest edger on roller/skid plate for extra stability and line up with edge of lawn. see fig P. Edge in direction indicated in Fig Q. so that de ...