Built-In Electric Oven Installation Instructions IMPORTANT ­ Save for local electrical inspector's use! READ THESE INSTRUCTIONS BEFORE INSTALLING THE OVEN. The rating plate is located on the internal side of the oven left hand side trim, it is visible when door is open. ! CAUTION ­ To avoid the risk of electrical shock, turn off power to oven branch circuit. 1. Check your local electric code or National Electric Code through your power company or secure the services of a qualified electrician. CAUTION ­ TO AVOID THE RISK OF FIRE: If your household branch-circuit wiring is aluminum, you must use special connectors designed for this purpose and listed by Underwriters Laboratories. Be certain to follow the connector manufacturer's instructions carefully. ! 3. Cut out cabinet to size specified on this sheet. Construct support-floor or 2 x 4 rails, covered with plywood or similar material. Check and level front to rear and side to side on support floor or rails. Make sure this support is rigidly mounted, as it supports the total weight of the unit (110 lbs). MAKE SURE THAT JUNCTION BOX IS PROPERLY LOCATED AS SHOWN IN DIAGRAM. Leave the bottom of the cabinet partially opened to permit free air circulation, otherwise water condensation may appear inside the control panel when operating the oven. 4. Remove all shipping and packing materials from unit and the lower grill assembly packed with the oven. FIGURE 1 27" min. 1 1/2" min. 5. There is 1 1/2" height adjustment on these models. (See Figure 2) With this adjustment and a 1/2" top trim overhand, a unit can be installed in existing opening 28 1/8" to 29 5/8" high. HOLE FOR CABLE 24 1/4" 28 1/8" min. 29 5/8" max. 23 1/2" min. (depth) 3" max. 26 7/8" 1 3/4" min. 24 7/8" min. (large) 25 5/32" max. FIGURE 2 GROUNDED ELECTRICAL JUNCTION BOX 29 1/8" 10" min. DOOR OPENING 72" 1 3/4" 4 MOUNTING SCREWS CABLE OVEN BOTTOM EXTENSION PANEL MOUNTING SCREWS SIDE OF OVEN NOTE: Allow at least 26 1/4" clearance for door depth when it is open. Maintain a minimum distance of 3" to a wall located on the door hinge side of the wall oven. 2. Measure cabinet carefully to ensure adequate clearance and proper fit. Do not install wall oven under the counter top. This oven requires a wall or cabinet opening of 28 1/8" high by 24 7/8" wide and 23 1/2" deep minimum. Install the oven at least 10" above the floor (refer to figure 1). 1 1 1/2" MAX. EXTENSION 318128601 (9806) Rev. D Printed in Canada To adjust oven height: A. Lay oven on its back. (See Figure 2) B. Remove the 6 screws that fasten the side extension panel to the bottom sides of the oven. C. Move each panel down to the position that increases the oven height to fit your opening. Each position changes oven height approximately 1/2". D. Line up the appropriate holes in the side extension panels and sides of the oven. Replace the 6 screws. E. Proceed with oven installation. Return oven to upright position. 6. Remove and lay aside the lower vent grille that is taped to the outer side panel of the oven. 7. Slide the oven into the opening until the side trims fit flush against the wall and check for levelness. Shim as required. Electrical conduit is pushed through the hole in the bottom of the opening. 8. Using the holes in the oven front frame as template, drill 1/8" diameter holes in the cabinet. 9. Fasten the top of the oven to the cabinet by means of 2 of the screws supplied in the miscellaneous parts bag. These holes are located underneath the control panel. 10. Fasten the bottom vent grille and the bottom of the oven to the cabinet by means of the 2 remaining screws (see figure 3). Electrical Connection to the Residence Electrical System The appliance should be connected directly to the fused disconnect or circuit breaker box through flexible, armored or nonmetallic sheathed copper cable (with grounding wire). Locate the junction box to allow 2 to 3 feet of slack in the line so that the range can be moved if servicing is ever necessary. Do not cut the conduit. A U.L.-listed conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box). Wire sizes (copper wire only) and connections must conform with the rating of the appliance. Electrical Shock Hazard · Electrical ground is required on this appliance. · Do not connect to the electrical supply until appliance is permanently grounded. · Disconnect power to the junction box before making the electrical connection. · This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. · Do not use the gas supply line for grounding the appliance. Failure to do any of the above could result in a fire, personal injury or electrical shock. FIGURE 3 SCREWS 2 FIGURE 4 Cable from Power Supply Black Wires FIGURE 5 Junction Box Cable from Power Supply Red Wires Red Wires White Wires White Wires Junction Box Bare Wires Black Wires Bare or Green Wire Cable from Range U.L.-listed Conduit Connector Cable from Range U.L.-listed Conduit Connector GROUNDED NEUTRAL 4-WIRE ELECTRICAL SYSTEM 2. Where local codes DO NOT permit, or if connecting to a 4-wire electrical system, DO NOT connect the cabinet-grounding conductor to the neutral (white) junction box wire (see Figure 5) A. Disconnect the power supply. B. Separate the bare copper and white appliance cable wires. C. Connect the white appliance cable wire to the neutral (white) wire in the junction box. D. Connect the 2 black wires together, then the two red wires together. E. Connect the bare copper grounding wire to the grounding wire in the junction box. Grounding Instructions This appliance is manufactured with neutral (white) power supply wire and a cabinet-connected green grounding wire. Connect the appliance cable to the junction box through the U.L.-listed conduit connector. Complete electrical connection according to local codes and ordinances. 1. Where local codes permit connecting the cabinetgrounding conductor to the neutral (white) junction box wire (see Figure 4) A. Disconnect the power supply. B. Connect together the 3 wires: green and white appliance cable wires and the neutral (white) wire in the junction box. C. Connect the 2 black wires together, then the two red wires together. Check Oven Operation 1. Check the oven in Bake. Turn the Oven Selector Knob to "Bake" and set the Oven Temperature Knob to 350°F. The Lower Oven Element should become red and the "Bake" Signal Light should glow. When the oven reaches the desired temperature, the light will go out. The "Bake" Signal Light is designed to turn on and off during baking as the Bake Element cycles on and off. 2. Check the oven in Broil. Turn the Oven Selector Knob to "Broil" and set the Oven Temperature Knob to "Broil". The Top Element should become red and Signal Light should glow. 3. Refer to the Use and Care Guide for proper operation of the electronic timer. 3 DOOR REVERSING FIGURE 6 DOOR REVERSAL PROCEDURE (see figure 6) 1. Pull the door open. HANDLE 2. While supporting the door with one hand, remove the 2 screws securing top hinge #1 to the door. Remove the top hinge, then lift up the door such as to clear the lower hinge pin and remove the door. 3. Lay the door on a table protected by a blanket; the inner door surface must face toward you. 4. Remove the 2 screws which secure the handle; remove the handle. Remove filler plates #2, #3, and #12 using a flat blade tool. 5. Reassemble upper hinge #1 at the lower end and on the opposite side of the door. This wall oven can easily be modified to a left or a right hand door opening. It is preferable to reverse door opening prior to the installation of the wall oven into the cabinet cavity. If wall oven is already installed, remove the 4 lateral screws securing it against the cabinet, then pull wall oven outward by approx. 50 mm (2"). Two of the lateral screws are located at the low end of upper grille; the other 2 screws hold the lower grille in place. Tools required: Philips #2 and Robertson #2 screwdrivers 6. Remove lower hinge #4. Relocate the nylon washer on the lower hinge pin. 7. Remove screws securing the top and bottom door trims #5 and #6 to the door; remove these trims. 8. Slide the glass panel flush with the edge of the enamelled steel inner door (toward the new handle location). 9. Invert position of trims #5 and #6 (trim #5 at the bottom and trim #6 at the top); reassemble trims. 10. Reassemble the handle and filler plates #2, #3 and #12 on the opposite side of the door. 11. Remove and relocate the filler plates #7 on the opposite side of the oven frame. 12. Remove the latch pin #10 and relocate latch on the opposite side of the oven door. 13. Invert positions of #8 and #9 hinge fixed parts (ex. from top left side to bottom right side). 14. Reassemble the door onto the wall oven; insert door into the fixed lower hinge, then proceed with the reassembly of the upper hinge. Align door by using available play in the hinge holes. 4 4 Horno eléctrico empotrado Instrucciones para la instalación IMPORTANTE - Guarde estas instrucciones para uso del inspector eléctrico local! LEA ESTAS INSTRUCCIONES ANTES DE REALIZAR LA INSTALACIÓN DEL HORNO. La placa de potencia indicada está ubicada en la parte interior del contramarco izquierdo del horno. Está visible cuando la puerta está abierta. cierre la energía eléctrica al circuito derivado del horno. 1. Verifique los códigos eléctricos locales o el Código Eléctrico Nacional con su compañia de electricidad, o el servicio debe de hacerlo un electricista calificado. ! AVISO - Para evitar el riesgo de choque eléctrico, ! AVISO - PARA EVITAR EL RIESGO DE FUEGO: Si el circuito derivado de la casa está fabricado con aluminio, use solamente los conectores especiales diseñados para este uso y enlistados de acuerdo con los Underwriters Laboratories. Asegurese de seguir atentamente las instrucciónes del fabricante de conectores. FIGURA 1 27" mín. 1 1/2" min. 24 1/4" 28 1/8" mín. 29 5/8" máx. 23 1/2" mín. 24 7/8" min. 25 5/32" máx. AGUJERO PARA EL CABLE 3" máx. 3. Corte el gabinete en conformidad con las dimensiones especificadas en esta hoja. Construya el soporte de suelo o ríeles de 2 x 4, recubridos con madera contrachapada u otro material similar. El soporte o los ríeles tienen que estar a nivel, de adelante hacia atrás, y de lado a lado. Para poder soportar todo el peso del electrodomestico (110 lbs.), la superficie donde se va a apoyar debe de ser de montaje muy rígido. ASEGURESE QUE LA CAJA DE EMPALME ESTA CORRECTAMENTE UBICADA COMO SE MUESTRA EN EL DIAGRAMA. Deje el fondo del gabinete parcialmente abierto para permitir la circulación de aire, de otra manera la condensación de agua puede aparecer al interior del panel de control cuando el horno está en funcionamiento. 4. Retire todos los artículos de expedición y de embalaje del electrodomestico y la asamblea de la rejilla inferior que vienen con el horno. 5. Estos modelos de horno cuentan con un ajuste de altura de 1 1/2" (vea la Figura 2). Con este ajuste y la pestaña de 1/2" el horno puede ser instalado en aberturas existentes de 28 1/8" a 29 5/8" de alto. 26 7/8" 1 3/4" mín. FIGURA 2 CAJA DE EMPALME ELECTRICA A TIERRA 10" mín. 29 1/8" ABERTURA DE PUERTA 72" CABLE FONDO DEL HORNO 4 TORNILLOS DE MONTAJE PANEL DE EXTENSION TORNILLOS DE MONTAJE PARTE LATERAL DEL HORNO NOTA: Deje por lo menos 26-1/4" de espacio libre para la profundidad de la puerta cuando esta abierta. Deje por lo menos 3" de espacio libre a una pared ubicada al lado de la bisagra de la puerta del horno de pared. 2. Meda atentamente las dimensiones del gabinete para asegurar una apertura adecuada y un ajuste apropiado. No instale el horno de pared debajo del mostrador. La abertura del gabinete o de la pared debe ser de 28 1/8" de alto por 24 7/8" de ancho y de una profundidad de 23 1/2" mínimum. Instale el horno por lo menos 10" por encima del suelo (refiera a la figura 1). 1 EXTENSION MÁXIMA 1 1/2" 318128601 (9806) Rev. D Impreso en Canadá Para ajustar la altura del horno: A. Ponga el horno apoyado en la parte trasera. (Vea la Figura 2). B. Quite los 6 tornillos que sujetan el panel de extensión lateral a los lados inferiores del horno. C. Mueva cada panel hacia abajo, hasta la posición que aumenta la altura del horno para que se adapte a la apertura que usted tiene. Cada posición cambia la altura del horno 1/2" aproximadamente. D. Alinee los agujeros apropiados en los paneles de extensión y en los lados del horno. Vuelva a poner los 6 tornillos. E. Proceda con la instalación del horno. Vuelva a poner el horno en posición vertical. 6. Retire y ponga a un lado la rejilla baja de ventilación que está pegada a la parte exterior del panel lateral del horno. 7. Deslize el horno en la apertura hasta que los contramarcos lateral ...