User manual FUJITSU SIEMENS AMILO DESKTOP SI 3535 - FIRST-TIME SETUP

Manual abstract:

... the packaging. After removal from the packaging, check the equipment for evidence of damage in transport. Check that that the equipment matches the delivery note. If you find damage in transport or a mismatch with the delivery note, inform your sales office without delay! Steps for initial startup Starting Up Initialstartup,overview Only a few steps are required to start up your machine for the first time: · Select the position for your machine and place it there · Connect the external devices · Check the rated voltage and connect the machine to the mains · Switch on the machine You can find more details on the individual steps in the following sections. External devices If you wish to attach other external devices (such as a printer) to your machine, complete the initial installation of your machine before connecting them. The steps for connecting these external devices are described in the following sections. Drives and modules If you wish to fit other drives or modules to your machine, complete the initial installation of your machine before fitting them. The steps for fitting drives and modules are described in the "AMILO Desktop" manual in the chapter"System expansion" . 10600985317, edition 1 English - 7 Getting started Setting up the device Device, Ergonomic Video workstation When installing your device, please read the recommendations and safety notes in the "Safety" manual. Do not place the machine in any position other than the one intended (upright on its feet). We recommend that you place your device on a surface with good anti-slip qualities. In view of the multitude of different finishes and varnishes used on furniture, it is possible that the rubber feet will mark the surface they stand on. Do not stack several devices on top of each other. Do not start the machine in any position other than upright on its feet. Depending on the location of your machine, it may emit annoying vibration or noises. To avoid this, allow a minimum clearance of 3 mm from other equipment or objects at the sides of the casing where there are no ventilation grilles. Make sure that the device is adequately ventilated. In order to avoid overheating, do not cover the ventilation area of the monitor or the device. Do not expose the device to extreme ambient conditions (see "AMILO Desktop S", Page 21, "Ambient conditions"). Protect the device against dust, humidity and heat. Connecting external devices Read the documentation on the external device before connecting it. With the exception of USB devices, always remove all power plugs before connecting external devices! Do not connect or disconnect cables during a thunderstorm. Always take hold of the actual plug. Never unplug a cable by pulling the cable itself. Connect and disconnect the cables in the order described below. Connecting the cables Turn off all power and equipment switches. Remove all power plugs from the grounded mains outlets. Connect all the cables to the device and the external devices. Please make sure that you always observe the safety notes provided in "Important information", Page 3 . Plug all data communication cables into the appropriate sockets. Plug all power cables into the grounded mains outlets. Cable, Cord Disconnecting the cables Switch off all affected devices. Remove all power plugs from the grounded mains outlets. Unplug all data communication cables from the appropriate sockets. Disconnect all of the cables from the device and from the external devices. Cable, 8 - English 10600985317, edition 1 Getting started Connecting the monitor Follow the instructions contained in the monitor manual to prepare the monitor for operation (e.g. connecting cables). Plug the data cable into the monitor port of the device. Monitor Depending on the expansion stage of your machine and your monitor, you can also connect the data cable to the DVI interface. Plug the monitor power cable into the grounded mains outlet. LX300 Wireless Keyboard Set The LX300 Wireless Keyboard Set with wireless mouse and keyboard is supplied with your machine. Digital radio technology frees you from cumbersome cables. Comply with the safety information in the safety manual and in the operating instructions for the "AMILO Desktop". Always use type AAA batteries. A symbol in the battery compartment shows you which way round to insert the batteries. Inserting batteries in the mouse 1 2 Insert the batteries (1). Set the on/off switch on the underside of the mouse to "ON" (2). 10600985317, edition 1 English - 9 Getting started To save power, set the on/off switch on the underside of the mouse to "OFF" when you are not going to use the mouse for an extended period. Inserting batteries in the keyboard A symbol in the battery compartment shows you which way round to insert the batteries. Insert the batteries. 10 - English 10600985317, edition 1 Getting started Connect the receiver Move the receiver in the direction of the arrow to take it out of the keyboard. 10600985317, edition 1 English - 11 Getting started Plug the receiver into a free USB port on your computer. The radio connection will be established automatically. Re-establishing the radio connection to the Keyboard Set if required Normally a radio connection code is generated automatically and the Keyboard Set is then immediately ready for operation. When the connection has successfully been established the LED on the receiver lights up green. The LEDs on the keyboard and mouse light up red if the battery voltage falls below 2.2 V. If the connection is not established automatically, or if it breaks down, proceed as follows: Unplug the receiver from your computer and plug it in again. Place the mouse at a distance no greater than 30 cm from the receiver. Keep the left mouse button pressed for five seconds. The LED on the receiver will flash green 4 times to indicate that the connection to the mouse has been established successfully. Keep the Esc key on the keyboard pressed for five seconds. Esc . The LED on the receiver will flash green 4 times to indicate that the connection to the keyboard has been established successfully. Skip forward and back buttons on the mouse In addition to the right and left mouse buttons and a mouse wheel, your mouse has two additional buttons (1): 12 - English 10600985317, edition 1 Getting started 1 These two buttons allow you to skip easily forward and back within an application, e.g. between Internet pages in a Web browser. Connecting external devices to the USB ports Devices, Externaldevices, USB devices, port, You can connect a wide range of external devices to the USB ports (e.g. printer, scanner, modem or keyboard). USB devices are hot-pluggable. This means you can connect and disconnect USB cables while your device is switched on. Additional information can be found in the documentation for the USB devices. Connect the data cable to the external device. Connect the data cable to one of the USB ports on your device. Device drivers The external USB devices you connect to the USB ports usually require no driver of their own, as the required software is already included in the operating system. However, if the external USB device requires its own software, please install it from the data carrier provided with the USB device. To ensure USB 2.0, the length of the cable used between the front USB port of your device and the external USB device must not exceed 3 m. 10600985317, edition 1 English - 13 Getting started Connecting the machine to the mains Mains adapter, 1 2 Connect the mains cable to the machine (1). Plug the mains plug into a three-pin socket (2). Switching on for the first time: installing the software Software, Installing, If the device is integrated into a network, the user and server details as well as the network protocol are required during the software installation. When you switch on the device for the first time, the supplied software is installed and configured. Plan a reasonable amount of time for this, as this process must not be interrupted. Once the installation has been started the device must not be switched off, unless the installation has been completed. During installation, the device may only be rebooted when you are requested to do so! The installation will otherwise not be carried out correctly and the contents of the hard disk must be completely restored. Switch on the monitor and the machine Switch on the monitor (see operating instructions for the monitor). 14 - English 10600985317, edition 1 Getting started Press the on/off button on the front of the machine. The operational display will light up and the machine will start. Installing the software During installation, follow the on-screen instructions. If anything is unclear regarding the data you are asked to input, read the online Help in your operating system. Installing, Software, Further information on the system, its drivers, utilities and updates can be found on the DVD "Drivers & Utilities" and on the Internet under "http://www.fujitsu-siemens.com/support". 10600985317, edition 1 English - 15 Operation Operation Switch the device on If necessary, switch the monitor on (see the operating manual for the monitor). Press the ON/OFF switch on the front of the device. The operational display will light up white and the machine will start. Monitor, Device, Switching off the device Shut down the operating system properly. If the operating system does not automatically switch the device into power-saving mode or switch it off, press the ON/OFF switch for at least 4 seconds. The device then consumes a minimum amount of energy. Monitor Device The ON/OFF switch does not fully disconnect the TV from the mains voltage. To completely disconnect the mains voltage, remove the power plug from the power socket. If necessary, switch the monitor off (see the operating manual for the monitor). 16 - English 10600985317, edition 1 Operation Operational display Machine Operationaldisplay The operational display appears on the front of the c ...