User manual FUJITSU 435DX

Copyright Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. LifeBook, Fujitsu,and the Fujitsu logo are trademarks of Fujitsu Limited. The following are registered trademarks of IBM Corporation:IBM,IBM PC AT, IBM PS/2. The following are registered trademarks of Microsoft Corporation:MS,MS-DOS, Windows NT, Microsoft Windows for Workgroups, Windows 95. PCMCIA is a trademark of the Personal Computer Memory Card International Association. Phoenix and the Phoenix logo are registered trademarks of Phoenix Technologies,Ltd. Pentium and MMX technology are trademarks of Intel Corporation. All Kensington Corporation products are registered trademarks of Kensington Microware Limited. PC-Doctor is a trademark of watergate.software.inc. SoftPEGTM is a registered trademark of CompuCore Multimedia Inc. LapLink is registered trademark of Traveling Software Inc. All other products are trademarks or registered trademarks of their respective companies. We cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. © Copyright 1996 Fujitsu PC Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu PC Corporation. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu PC Corporation. CAUTION Changes or modification not expressly approved by Fujitsu PC Corporation could void this user's authority to operate the equipment. FCC Notices Notice to Users of Radios and Television These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi on s ,m ay cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. s Increase the separation between the equipment and receiver. s Connect the equipment into an outlet that is on a different circuit than the receiver. s Consult the dealer or an exp erienced radio/TV technician for help. Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. s If you experience trouble with this equipment please contact your support representative, toll free at 1-8008FUJITSU (1-800-838-5487) or Fujitsu Computer Products of America (FCPA),7300 NE Evergreen Parkway, Hillsboro, OR 97124, telephone 503-681-7300. UL Notice(For Authorized Repair Technicians Only) CAUTION: For continued protection against risk of fire, replace only with the same type and rating fuse. CAUTION:Danger of explosion if CMOS battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instruction. WARNING: CMOS Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. DOC (Industry Canada) Notices Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada. Table of C ontents Table of Contents Preface . . . . . . . . . . . . . . . . . . . vi Section Two Using Your LifeBook 400 Series Using your LifeBook 400 Series from Fujitsu . . . . . . . . . . . . . Status Indicator Panel . . . . . . . . . Power Management Controls . . . . . Power On . . . . . . . . . . . . . . . Special Operating System Features . . Power OV . . . . . . . . . . . . . . . Restarting the System . . . . . . . . . Battery . . . . . . . . . . . . . . . . . Integrated TouchPad Pointing Device Using the Keyboard . . . . . . . . . . Floppy Disk Drive . . . . . . . . . . . CD-ROM Drive . . . . . . . . . . . . Hard Drive . . . . . . . . . . . . . . . Power-Saving . . . . . . . . . . . . . Video and Audio Functions. . . . . . File Transfers. . . . . . . . . . . . . . Infrared Communication Port . . . . Anti-Virus Software . . . . . . . . . . Section Three Configuring Your LifeBook 400 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 17 20 22 23 23 24 25 28 30 32 35 35 36 41 43 43 43 Boot Sequence . . . . . . . . . . . . . . . . Identifying the Dr ives . . . . . . . . . . . . BIOS Setup Utility. . . . . . . . . . . . . . Navigating Through the Setup Utility . . . Main Menu ­ Setting System Parameters . Exiting from the Main Menu . . . . . . . . Advanced Menu ­ Setting Device Controls Exiting from the Advanced Menu . . . . . Security Menu . . . . . . . . . . . . . . . . Exiting from the Security Menu . . . . . . Power Savings Menu . . . . . . . . . . . . Exiting from the Power Savings Menu . . . Boot Menu ­ Selecting the Operating System Source. . . . . . . . . Exiting from the Boot Menu . . . . . . . . Exit Menu ­ Leaving the Setup Utility . . . Setting Up Your Save-To-Disk File Allocation. . . . . . . . . . . . . . . . . . . . . . . . . . . 46 46 47 48 50 59 59 66 67 69 71 71 Section One Setting Up Your LifeBook 400 Series Unpacking. . . . . . . . . . . . . . . . . . . . 2 Overview of Features . . . . . . . . . . . . . . 3 Component Identification . . . . . . . . . . . 4 Power Sources. . . . . . . . . . . . . . . . . . 9 Data Security . . . . . . . . . . . . . . . . . . 9 Starting Your NoteBook for the First Time . 10 User Registration . . . . . . . . . . . . . . . 13 Learning About Your Operating System and Application Software. . . . . . . . . . 14 . 73 . 74 . 74 . 75 ii LifeBook 4 00 Series from Fujitsu Table of Contents Section Four User Installable Features RAM Module . . . . . . . . . . . . PC Cards . . . . . . . . . . . . . . . Installing a Theft Prevention Lock . Optional External Installation of Floppy Disk Drive . . . . . . . . Nickel Metal Hydride Battery Pack . Multi-function Bay . . . . . . . . . CD-ROM Drive . . . . . . . . . . . Removable Floppy Disk Drive . . . Installing Devices on the LPT Port . Installing Devices on the COM Port Installing External Monitors . . . . Installing a Mouse or Keyboard . . Installing a Replicator Port or Mini-Docking Station . . . . . . Installing Audio Input Devices . . . Installing Audio Output Devices . . . . . . . 78 . . . . . 81 . . . . . 84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 85 86 87 88 88 88 88 88 Section Five Troubleshooting Identifying the Problem . . . . . . . . . . . . 92 Specific Problems . . . . . . . . . . . . . . . 93 Power On Self Test Messages . . . . . . . . 112 Emergency CD-ROM Tray Release . . . . . 115 Installing and Removing the Internal Hard Drive . . . . . . . . . . . . 115 Restoring Your Pre-installed Software from CD-ROM . . . . . . . . . . . . . . 116 Appendices Appendix A Specifications . . . Warranty . . . . . . . . . . . . LifeBook 435Dx Specifications Approvals . . . . . . . . . . . . Popular Accessories . . . . . . Appendix B Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 122 122 124 124 126 Index . . . . . . . . . . . . . . . . . . . . 134 Section Six Care and Maintenance Care and Maintenance . . . . . . . . . . . . 119 Caring for Your Notebook . . . . . . . . . . 119 Increasing Battery Life . . . . . . . . . . . . 119 . . . . . 88 . . . . . 89 . . . . . 89 iii Preface Li feB ook 40 0 Se ri e s from F uj i tsu Preface Preface The LifeBook 400 Series from Fujitsu PC Corporation is a powerful notebook computer. It is powered by an Intel Pentium microprocessor with MMX technology, has a built-in color display, a CD-ROM drive and brings the computing power of desktop personal computers (PCs) to a portable environment. This manual explains how to operate your LifeBook 400 Series' hardware and built-in system software. The LifeBook 400 Series is compatible with the IBM PC AT.® Depending on your model,it comes with Windows® 95, Windows for WorkgroupsTM Version 3.11 and MS-DOS Version 6.22 or only Windows 95 pre-installed. When you first start your notebook, you will be asked to select a single operating system if both are present. (See pages 10­13 for more information on selecting your operating system.) Your LifeBook 400 Series is a completely selfcontained unit with a passive-matrix (DSTN) color LCD display. It has a powerful interface that enables it to support a variety of optional features. (Figure P-1.) CAUTION When you first turn on your LifeBook 400 Series the Windows 95 Setup screen will appear. This is true even if you will be using Windows for Workgroups. vi LifeB ook 40 0 Series from Fuj itsu LifeBook 400 Series from Fujitsu Figure P-1 LifeBook 400 Series with both Fujitsu and Third Party Options vii Preface Conventions Used in the Guide In this manual, figures which show screens are intended as examples only, and screen and file names may differ in actual use. Messages displayed by your LifeBook 400 Series appear in Courier type. Example: Starting MS-DOS Commands that you enter into your notebook using the keyboard appear in Courier type. Example: C:>DIR/P Keyboard keys are shown in boldface Helvetica type. Example: Fn, F1, Esc, and Ctrl. Pages with additional information about a specific topic are cross-referenced within the text. Example: (See page xx.) POINT The point icon highlights information that will enhance your understanding of the subject material. CAUTION The caution icon highlights information that is important to your safety, to the safe operation of your notebook, or to the integrity of your files. Please read all caution information carefully. viii Section S e t ti n g U p Yo u r Li fe B o o k 4 0 0 Ser i e s Unpacking . . . . . . . . . . . . . . . . . . . 2 Overview of Features . . . . . . . . . . . . . 3 Component Identification . . . . . . . . . . . 4 Power Sources . . . . . . . . . . . . . . . . . 9 Data Security. . . . . . . . . . . . . . . . . . 9 Starting Your Notebook for the First Time . . 10 User Registration . . . . . . . . . . . . . . . 13 Learning About Your Operating System and Application Software . . . . . . . . . . . 14 One Section One Section ONE Setting Up Your LifeBook 400 Series from Fujitsu This section describes how to set up your LifeBook 400 Series from Fujitsu. We strongly recommend that you read it before using your notebook ­ even if you are already familiar with notebook computers. s Modular 3.5" Floppy Disk Drive (located in the accessories box).(Figure 1-3.) User's Guide. Registration card and customer information pack. Microsoft Windows 95 Manual. Additional equipment and documentation depending on the option package you have purchased. Figure 1-2 AC Adapter Unit s s s s Unpacking When you receive your notebook,unpack it carefully, and compare the parts you have received with the items listed below. For a standard configuration you should have: s s LifeBook 400 Series from Fujitsu.(Figure 1-1.) AC Adapter with AC power cord (located in the accessories box).(Figure 1-2.) Modular 10-speed CD-ROM Drive (already installed in your notebook). Figure 1-1 LifeBook 400 Series Notebook Figure 1-3 Floppy Disk Drive s 2 LifeBook 4 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 40 0 Se r i e s Once you have checked and confirmed that your notebook system is complete, connect the AC Adapter and follow the instructions on pages 10­13 to accept the conditions for using the LifeBook 400 Series and for selecting the operating system you will use. When you have completed that setup process please complete and send in your registration card. s s Built-in 1.3GB hard drive. Multi-function bay which supports warm swapping of the following: s s Full size keyboard with three dedicated Windows 95 keys. Hot swap connection for an external keyboard or an external mouse. Stereo line in jack. Stereo headphone jack. Standard Pre-installed software: s s s 3.5" floppy disk drive (included with all models). 10-speed CD-ROM drive (included with all models). s s s s Overview of LifeBook 400 Series Features The LifeBook 400 Series is a compact, yet powerful notebook computer available with standard features including: (See Appendix A, pages 122­125, for detailed information.) s s s s Nickel Metal Hydride (NiMH) Battery Pack. 16-bit Sound BlasterTM-compatible sound chip. Zoomed Video port for full motion video acceleration. Built-in stereo speakers. Two Type II or one Type III PC Card slot. IrDA 1.0 compatible infrared port for wireless data transfer. Integrated TouchPad Pointing Device for easy cursor control. External monitor support. Operating System. LapLink®7.0 for file transfers via modem, cable or infrared port. PC-DoctorTM for system diagnostics. SoftPEGTM from CompCore,a MPEG-1 video player. ESS AudioRackTM, to take advantage of the notebook's audio capabilities. McAfee® VirusScan®. Some models may include additional software. s s s s s 133 MHz Intel PentiumTM processor with MMX technology. 16MB EDO RAM standard, expandable to 80MB. 12.1" passive-matrix (DSTN) color display with 800 x 600 resolution. 1MB Video RAM. s s s s s s s s 3 Section One Component Identification For detailed specifications refer to Appendix A on pages 122­125. Display Panel Latch This latch locks and releases the display panel. LCD Display Panel This is a color LCD panel with back lighting for the display of text and graphics. Brightness Control The brightness control adjusts the overall intensity of the display screen back lighting. Contrast Control The contrast control adjusts the contrast of the display screen. It is located just below the brightness control. Status Indicator Display LCD display of the status of the power state and source, Suspend Mode, battery charge, floppy disk drive activity, hard drive activity, CD-ROM drive activity, PC Card activity, Caps Lock, Num Lock and Scroll Lock. 4 Suspend/Resume Button The Suspend/Resume Button allows you to suspend computer activity without turning off your notebook power, and to return it to an active state. This feature saves power, and is particularly useful when your notebook is running only on battery power. (See pages 20­22, 36­41,and 69­72 for more information on Power Management.) Display Latch Figure 1-4 Top and Front Panel LifeBook 4 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 40 0 Se r i e s Display Latch LCD Display Status Indicator Display Stereo Speaker Brightness Control Keyboard Contrast Control Keyboard Removal Tab Suspend/Resume Button Closed Cover Switch Stereo Speaker TouchPad Pointing Device Multi-function Bay Keyboard Removal Tab Figure 1-5 LifeBook 400 Series with Display Open 5 Section One CAUTION Be sure you know what settings are active for your Suspend/Resume Button before you use it as misuse can result in data loss. (See the Power Savings Menu of the BIOS Setup Utility on pages 69­72 for more information.) the front of the keyboard in place.Lifting the tabs is only necessary to access the Memory Expansion Chamber which is under the keyboard. (See pages 78­81 for more information. ) PC Card Slots Eject Buttons Optional External Floppy Disk Drive Adapter Connector Built in Microphone CAUTION Do not attempt to install or remove a RAM Module if your notebook has been recently used. The surface area under the keyboard can be very hot and may injure you. Lock Battery Eject Button Figure 1-6 LifeBook 400 Series Left Side Panel Closed Cover Switch This switch turns off the LCD back lighting when the display panel is closed,thus saving power. Speakers The built-in dual speakers output stereo sound from your notebook. Keyboard A full size keyboard with dedicated Windows 95 keys for input into your notebook. Keyboard Removal Tabs A pair of tabs which cover screws which hold 6 TouchPad Pointing Device A touch sensitive cursor control system with two click buttons. Multi-function Bay This bay accommodates: s s PC Card Slots, with Cover, Lock and Eject Button The PC Card Slots allow you to install two type I or II PC Cards or one type III PC Card. (See pages 81­83 for more information on PC Cards.) The buttons to the left of the card slots lock the cards in place,and the buttons to the right of the slot ejects the card(s) from the slot. External Floppy Disk Drive Adapter Connector A connector for attaching an optional external floppy disk drive adapter. The adapter allows you to use your modular floppy disk drive when the multi-function bay is being used for another purpose. 10-speed CD-ROM drive. 3.5" floppy disk drive. LifeBook 4 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 40 0 Se r i e s Main Battery Eject Button This button releases the Removable Main Nickel Metal Hydride Battery Pack for removal and installation. Built-in Microphone The built-in microphone allows mono audio input to your notebook. Volume Control This knob provides hardware control of sound level of audio outputs from your notebook. Audio Stereo Line In Jack The Audio Input Jack allows you to connect an external audio source to your notebook,like an audio cassette player. This jack will not support an external microphone. Headphone Jack You can install headphones or powered external speakers in the Headphone Jack. Multi-function Bay Release Button This is the release to allow removal and installation of devices in the Multi-function Bay. Power Switch This switch is the main power switch for your notebook. PS/2 Connector The PS/2 Connector allows you to connect an external PS/2 keyboard,mouse, or numeric keypad. DC Power Input Connector The DC Power Input Connector allows you to plug in the Fujitsu AC Adapter or the optional Fujitsu Auto Adapter. Theft Prevention Lock Slot This is a slot that allows you to attach a physical lock down device. Serial Interface Connector (COM Port) The Serial Interface Connector allows you to connect serial RS-232C devices, such as a serial printer or a serial scanner. Expansion Bus Connector This connector is for connection to an optional port replicator or docking station. The connector cover must be closed and the sliding panel opened to reveal only the Expansion Bus Connector when connecting a port replicator or docking station. 7 Volume Control Headphone Jack Power Switch DC Power Input Connector Audio Stereo Line In Jack Multi-function Bay Release Button PS/2 Connector Theft Prevention Lock Slot Figure 1-7 LifeBook 400 Series Right Side Panel CAUTION There are software volume controls. The knob setting and the software settings will interact. Software volume Off will override the knob setting. (See Volume Control on pages 42­43 for more information.) Section One Parallel Interface Connector (LPT Port) The Parallel Interface Connector allows you to connect parallel devices, such as a parallel printer, to your notebook. External SVGA or Hi Res Monitor Connector This connector allows you to connect an external VGA or SVGA CRT or Hi-Res monitor to your notebook. Infrared IrDA Compatible Communication Port The IrDA compatible Communication Port allows you to communicate with another IrDA compatible device without a cable. (See page 43 for more information.) Tilt Adjustment Feet These are a pair of feet which flip down and hold the back of the keyboard approximately 6° higher than the front when resting on a flat surface. They are designed to make using your notebook keyboard more comfortable. Main Unit Label This label has the model number, serial number and other information about your notebook. 8 COM Port Expansion Bus Connector Tilt Adjustment Foot Tilt Adjustment Foot LPT Port Configuration Label Main Unit Label Internal Hard Drive Chamber Monitor Connector Infrared Port Figure 1-8 LifeBook 400 Series Back Multi-function Bay Battery Chamber Figure 1-9 LifeBook 400 Series Bottom CAUTION The cover which closes over the connectors on the rear of your notebook can be damaged if it is left open when your notebook is moved around. Configuration Label This label has manufacturer information that you will need to give your support representative so that he or she can help you. It identifies exactly the version of various component parts of your notebook. LifeBook 4 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 40 0 Se r i e s Internal Hard Drive Chamber This chamber houses the internal hard drive. It should only be accessed for maintenance by an authorized maintenance provider. Battery Chamber This chamber houses the Nickel Metal Hydride Battery Pack or the optional Lithium ion Battery Pack. Power Sources Your notebook has three possible power sources: the Nickel Metal Hydride Battery Pack, the AC Adapter, or the optional Auto Adapter. Connecting the Power Adapters The AC Adapter or the Auto Adapter provides power for operating your notebook and charging the battery pack.(Figure 1-10.) To Connect the AC Adapter Data Security Your LifeBook 400 Series from Fujitsu has a built-in hardware control password security feature that allows you to protect stored data from unauthorized access. Your operating system and some applications have software control password security features that allows you to protect all or portions of the data stored in your notebook from unauthorized access. Hardware Data Security Features When you are using the built-in har dware control password to gain access to your notebook the actual password will not appear on the screen. This is a safety precaution. The hardware control security parame ters are set from the BIOS Setup Utility. (See Security Menu on pages 67­69 for more information on setting and clearing passwords and enabling and disabling built-in security features.) CAUTION The Nickel Metal Hydride Battery Pack is not charged when you purchase your notebook. Initially you will need to connect the AC Adapter or the Auto Adapter to use it. It can take up to 3 hours to charge a Battery Pack if your notebook is Off or in Suspend Mode. If your notebook is in use, it can take up to 9 hours or more to charge a Battery Pack. 1.Plug the DC output cable of the AC Adapter into the DC Power Input Connector on the right side panel of your notebook. 2.Plug the AC Adapter into an AC electrical outlet. To Connect the Optional Auto Adapter 1.Plug the DC output cable into the DC Power Input Connector on the right side panel of your notebook. 2. Plug the Auto Connector into the cigarette lighter of a car or other vehicle with the ignition key in the On or the Accessories position. 9 Section One Software Data Security Features The operating system and some applications have security features that are independent of the built-in hardware protection features that are controlled from the BIOS. See your software documentation for more information about these features. CAUTION Software security feature passwords may not be the same as the hardware security passwords. Be sure you know which features are controlled from software and which from hardware or you may lock yourself out of your own data or lock up your hardware and not be able to operate your notebook. CAUTION Make sure you memorize your passwords for both hardware and software. If you forget, you may not be able to use your notebook, and you will have to contact your service provider and arrange to have them reset the hardware system password. See your software manuals for what to do if you forget your software security password(s). When you turn on your notebook for the first time it will p erform a power on self test and display some status information on the screen with a message: Press for Setup . If you do nothing the system will read the hard drive for the operating system software and the Windows 95 Setup Screen will appear. (See Power On on pages 22­23 for additional help.) You will then be stepped through the condition of useand operating system selection process. You must complete this initial process before you will be able to use your notebook. Starting Your Notebook for the First Time Booting the System The first time that you turn on your notebook you will need to attach your AC Adapter as the battery is not charged when it arrives. We strongly recommend that you do not attach any other external devices and do not put any CD or floppy disk in the drives until you have gone through the initial power on sequence. CAUTION If you have purchased a system which allows you to use a choice of operating systems, the Operating System selection can only be made once. You cannot change your mind, the option will never be available again. 10 LifeBook 4 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 40 0 Se r i e s Conditions of Use The first time you start your notebook you must confirm your acceptance of the copyright limitations for your pre-installed software. If you have purchased a unit which allows you to use a choice of operating systems you must choose between Windows 95 and Windows for Workgroups. Once you have chosen your operating system you cannot change your mind, the other system will not be available to you.Please decide carefully. After your notebook completes the installation of the operating system it will not ask you again for confirmation of the conditions of use nor to choose an operating system. Every LifeBook 400 Series Model has 10 screens to read carefully and/or answer questions by typing in information. If your notebook has a choice to use Windows for Workgroups there will be three additional screens. All of the screens are Windows 95 Setup screens. You cannot use your notebook until this setup process is completed. The bottom of each screen has a Button and a Cancel Button which are activated by the Integrated Touchpad Pointing Device cursor control and button click. The Button activates any choices or information you have entered and takes you on to the next screen. The Cancel Button allows you to stop the setup process. If you stop the process your notebook will come back to the place in the Windows 95 Setup where you left off the next time you start your machine. The screens you will be required to respond to are shown with the required action. Welcome to Windows Setup Read and then click on the Next> Button. Regional Settings Select language, number format,date format, etc. for the operating system to use by moving cursor up and down the list to the desired world region shown in the table and then clic k on the Next> Button. Use the up arrow and down arrow keys to move down up and down the text one line at a time. Keyboard Layout Select the keyboard language and format you wish to use by moving cursor up and down the list to the desired selection shown in the table and then click on the Next> Button. You can scroll through the text using the up arrow and down arrow keys to move down up and down the text one line at a time. User Information ­ Software Licensing Fill in your name and your company name as you would like to see it on the software license and then click on the Next> Button. You must make an entry in order to continue. 11 CAUTION When you first turn on your notebook the Windows 95 Setup screen will appear. This is true even if you will be using Windows for Workgroups. Section One POINT If your system comes with Windows 95 only, you will find a Recovery CD-ROM packet in your accessories box. Please store the packet in a safe place in case there is a loss of data. (See Restoring Your Pre-installed Software from CDROM on page 116.) License of Windows 95 Read carefully and then click on the Next> Button. License Agreement Read the agreement carefully. You can scroll through the text using the Integrated TouchPad Pointing Device to activate the scroll bar or use the up arrow and down arrow keys to move up and down the text one line at a time. When you finish reading simply point and click to accept or reject the terms of the agreement and then click on the Next> Button. POINT If you reject the terms of the license agreement the operating system setup will abort and shutdown your notebook. When you turn on the system the next time, it will begin the Setup process again. Certificate of Authenticity Look in the box that your notebook came in and you will find a Windows 95 Certificate of Authenticity and a Windows 95 Users manual. On the certificate ­ and also on the back of the manual ­ you will find a bar-code with a number above it. These numbers should be the same. They are your product code and the number you should enter on the Certificate of Authenticity screen. When you have entered the number exactly as shown then click on the Next> Button. CAUTION If your system came with a choice of operating systems, you will need to make back up disks. (See Create System Disks page 13.) *Windows Version To select Windows for Workgroups point and click on the Change Button. To select Windows 95 point and click on the Next> Button. (If you select Windows 95 you will go directly to the Configuring the Computer Screen.) *Operating System Choice To select Windows for Workgroups point and click on the Windows for Workgroups selection and then point and click on the Next> Button. To select Windows 95 point and click on the Windows 95 selection and then point and click on the Next> Button. Configuring the Computer If you have a unit with only Windows 95 or have selected Windows 95 this screen will appear when Windows 95 is ready to install. (If you purchased a LifeBook 400 Series which only comes with Windows 95 this screen will appear immediately after the Certificate of Authenticity Screen.) You may be prompted for time zone and printer. You do not need to select a printer at this time. 12 LifeBook 4 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 40 0 Se r i e s Installing Devices This screen will appear while your notebook loads the operating system and when it finishes it will automatically go to the next screen. CAUTION If you have chosen Windows for Workgroups please follow the instructions on the coupon that is included in the accessories box with your notebook. This provides for exchanging the Windows 95 manual for a Windows for Workgroups manual. *Create System Disks If your system came with a choice of operating systems, you will be prompted to create system disks. We strongly recommend that you make a system backup so you can restore your factory installed software in case of data loss. If you have chosen Windows 95 you will need to backup your operating system and your factory installed applications and drivers. The backup will require 40 floppy disks. If you have chosen Windows for Workgroups you only need to backup the factory installed applications and drivers. The backup will require 9 floppy disks. Finishing Setup Click on the Finish Button and your notebook will restart with the selected Windows operating system ready for normal operation. User Registration There are three ways to register your notebook. 1. Mail-in Registration ­ Fill in the registration card provided in the box with your LifeBook 400 Series and mail it to Fujitsu. 2.On-line Electronic Registration ­ Fill out the registration form behind the Fujitsu Icon on your Desktop and send it by e-mail. 3. Internet Registration ­ Use the registration utility on the Fujitsu PC S ervice and Support Web Site at www.8fujitsu.com to register your notebook. POINT If you do not have enough floppy disks available during the setup process you can create system backup disks at any time. From the Start Menu, select Accessories, then System Tools, then Create System Disks. 13 Section One Learning About Your Operating System and Application Software Tutorials All operating systems and most application software have built-in tutorials. We highly recommend that you step through the tutorial before you use an application, even if you are familiar with the same application on a different machine,an earlier version of the application, or with a similar p roduct. Manuals In the accessories box you will find manuals f or Windows 95 and other pre-installed software. If you have Windows for Workgroups,and have chosen it as your operating system, follow the instructions on the coupon in the accessories box in order to exchange the Windows 95 manual for a Windows for Workgroups manual. Software manuals of pre-installed software that are not in the accessories box are available online. See the help screens of your pre-installed software. We recommend that you review these manuals for general information on the use of these applications and to get a basic understanding of what is covered in the manual,and how it is organized,should questions arise as you use the applications. 14 Section Using Your LifeBook 400 Series from Fujitsu Using Your LifeBook 400 Series from Fujitsu . 16 Status Indicator Panel. . . . . . . . . . . . . 17 Power Management Controls. . . . . . . . . 20 Power On . . . . . . . . . . . . . . . . . . 22 Special Operating System Features . . . . . . 23 Power Off . . . . . . . . . . . . . . . . . . 23 Restarting the System . . . . . . . . . . . . 24 Battery . . . . . . . . . . . . . . . . . . . . 25 Integrated TouchPad Pointing Device. . . . . 28 Using the Keyboard. . . . . . . . . . . . . . 30 Floppy Disk Drive . . . . . . . . . . . . . . . 32 CD-ROM Drive . . . . . . . . . . . . . . . . 35 Hard Drive . . . . . . . . . . . . . . . . . . 35 Power-Saving. . . . . . . . . . . . . . . . . 36 Video and Audio Functions . . . . . . . . . . 41 File Transfers . . . . . . . . . . . . . . . . . 43 Infrared Communication Port . . . . . . . . . 43 Anti-Virus Software. . . . . . . . . . . . . . 43 Two Section Two Section TWO Using Your LifeBook 400 Series from Fujitsu This section describes the indicators, buttons, connections and operating modes of your notebook and their use. Opening the Unit Lifting the latch releases the cover and allows your notebook to be opened.Lift the display backward until the screen is at a comfortable viewing angle.(Figure 2-1.) Adjusting the Built-in Display When you turn on your notebook, you may want to adjust the bri gh tn e s sl evel of the screen for best visibility. To do this, adjust the brightness slider on the right side of the built-in display screen. You may need to adjust the brightness periodically for different operating environments. You will probably want to adjust the contrast as well as the brightness. To do this, use the contrast slider on the right side of the built-in display screen just below the brightness control.(Figure 2-2.) 16 Brighter Less Bright Figure 2-1 Opening the LCD Display More Contrast POINT The higher the level of brightness, the more power your notebook will consume, and the faster the battery will discharge. Adjusting the Keyboard Angle On the bottom of your notebook, near the back,are a pair of feet which flip down and hold the back of the keyboard about 6° higher than the front when resting on a flat surfa ce. Less Contrast Figure 2-2 Display Adjustments They are designed to make using your notebook more comfortable when using the keyboard. The feet must be folded flat against the bottom of your notebook when opening or using a CD-ROM or it will not open or operate properly. (See Figure 1-9 on page 8. ) LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series CAUTION Do not operate the CD-ROM drive or attempt to open the tray unless your notebook is sitting on a flat surface and the adjustment feet are folded against the bottom of your notebook. Using a CDROM drive when it is not level may damage the drive or prevent proper operation. CAUTION When you are not using the adjustment feet be sure that they are folded flat against the bottom of your notebook. They could be broken off, or injure someone, if not used properly. Power Battery Charging AC Adapter Inidcator Battery Level Battery Identifier Status Indicator Panel The Status Indicator LCD Display Panel is located in the recess just above the keyboard. (Figure 2-3.) The appropriate indicators become visible when you use your notebook. Unused CD-ROM Floppy NumLock Scroll Lock Drive Disk Indicator PC Card Indicator Access Drive Access CAP Lock Indicator Access Indicators Indicator Hard Indicator Drive PC Card Access Identifier Indicator Figure 2-3 Status Indicators 17 Section Two Power Indicator The Power Indicator tells you when the system is operational. It is on steady when there is power to your notebook, and blinks when the system is in Suspend Mode. It goes off when the system has entered Save-to-Disk Mode, has entered the Windows 95 shutdown inactivity state, or the power is turned off from the Power Switch. when either of the adapters is active and Off when power comes from the battery alone. If a battery is charging the power adapter is active regardless of the setting of the Power Switch. The AC Adapter is also active in the Windows shutdown state, regardless of the battery status. If there is no battery charging, and the Power Switch is Off, then the AC Adapter Indicator and the Battery Condition Indicator will all be Off. Battery Condition Indicator This indicator shows whether or not the Nickel Metal Hydride Battery Pack is installed and indicates the condition.(Figure 2-3.) Battery 0 is the Nickel Metal Hydride Battery Pack. The Battery Status Indicator is displayed only if the battery is install ed .( Ba t tery 1 display will flash when you power up but will never be displayed.) A small arrow icon appears to the left of the battery symbol and above the number if the battery is charging. The charging indicator flashes if the battery is too hot or too cold to charge. The charging indicator operates whether the Power Switch is Off or On. The symbols inside the bat- tery outline indicate the operating level available for the battery. (Figure 2-4.) If there is no battery charging and the Power Switch is Off then the AC Adapter Indicator and the Battery Condition Indicator will all be Off. 76­100% 51­75% POINT When your notebook has been shutdown from Windows 95, it is the same as turned off from the Power Switch except that it can be turned on by pressing the Suspend/Resume Button. It is not drawing current in this state. 26­50% 13­25% Low Battery 12% Dead Battery AC Adapter Indicator The AC Adapter Indicator tells you whether the system is operating on the AC or Auto Adapter, or running on battery alone. The indicator is On 18 Shorted Battery Figure 2-4 Battery Condition Indicator LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series CAUTION Turning off the power with the Power Switch or using the Suspend/Resume Button when any of the Access Indicators are On may cause loss of data and/or system errors. CD-ROM Drive Access Indicator The CD-ROM Access Indicator tells you a CD-ROM is being accessed. POINT If you do not wish to have the CD automatic insertion function you can disable it. In order to disable the CD automatic insertion function proceed as follows: 1. Save all data and close all applications. 2. Click on the Start Button. 3. Point to Settings. 4. Click on the Control Panel. The Control Panel window will be displayed. 5. Double click on the System icon. The System Properties dialogue box will be displayed. 6. Click on the Device Manager tab. The device list will be displayed. 7. Click on the + to the left of the CD-ROM icon. The manufacturer and model of the installed CD-ROM Drive will be displayed. 8. Click on the CD-ROM Drive manufacturer and model identification. 9. Click on Properties. The CD-ROM Drive Properties dialogue box will be displayed. 10. Click on the Settings tab. 11. Click on the automatic insertion box to toggle it Off. 12. Click on OK. 13. Click on OK in the System Properties dialogue box. 14. Restart your notebook according to the message displayed. You can re-enable the function by repeating the process except in step 11 change the setting to On. POINT When using Windows 95, the CD-ROM automatic insertion function periodically checks for a CD installed in the drive, causing the access indicator to flash. The CD automatic insertion function allows the system to automatically start a CD application as soon as a CD is inserted in the drive and the tray is closed. It will begin playing an audio CD or will start an application if the CD has an auto run file on it. 19 Section Two CAUTION If you switch off power using the Power Switch or operate the Suspend/Resume Button while any of the access indicators are on, you may cause data to be lost and/or a system error to occur. POINT Windows 95 displays of PC Card slot numbers may be different than Status Indicator slot numbers. ScrollLock Indicator The ScrollLock Indicator tells you when you are in Scroll Lock Mode. You can activate or deactivate the scroll lock mode by pressing the Scr Lk/Num Lk key. Deactivate the mode the same way that you activated it. This indicator is inactive if you are using an external keyboard. Hard Drive Access Indicator The Hard Drive Access Indicator tells you when the internal hard disk is being accessed. Floppy Disk Drive Access Indicator The Floppy Disk Drive Access Indicator tells you a floppy disk is being accessed. PC Card Access Indicators The PC Card Access Indicator tells you an installed PC Card is being accessed. Card 0 is the bottom connector and Card 1 is the upper connector in the card slot. Type III cards are always Card 0 only. NumLock Indicator The NumLock Indicator tells you the internal keyboard is set in ten-key numeric mode. (See page 31 for more information on the numeric keypad.) You can activate the NumLock Mode by pressing the Scr Lk/Num Lk key while holding down the Shift key. Deactivate the mode the same way that you activated it. This indicator is inactive if you are using an external keyboard. CapsLock Indicator The CapsLock Indicator tells you when the keyboard is set for all capital letters. Activate the Caps Lock Mode by pressing the CapsLock key on the keyboard. Deactivate the mode the same way that you activated it. This indicator is inactive if you are using an external keyboard. Power Management Controls The Power Panel by Phoenix provides Windows 95 desktop access to a comprehensive combination of power management settings without entering the BIOS Setup Utility. To access the Toolbar for the Power Panel left click on the "Atomic Icon" on the end of the Windows Taskbar. The Toolbar will appear. (The default position for the Toolbar is on the left edge of the screen, but you can move it wherever you like.) The standard Power Management Toolbar has three power saving profile choices and four activation choices. The profiles are groups of system settings designed to fit power operation to specific user operating conditions. 20 LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series The standard profile choices are: Maximum Battery Life. Maximum Performance. Presentation. The standard activation choices are: Suspend Mode. Save-to-Disk Mode. Video Standby Mode. PC Card Control. A custom Power Management Toolbar is also available from the "Atomic Icon" by right clicking and using the menu. Use your on-line help from the menu for instruction on how to create a custom Toolbar. Once you have created your Custom Toolbar you can use the menu to set the Custom Toolbar as the default. Power Panel On-line Help On-line help is accessed from the menu that appears when you right click on the "Atomic Icon" of the Windows Taskbar. Maximum Battery Life Profile The Maximum Battery Life profile is a combination of timeouts and other power savings parameters selected by Fujitsu as the settings that will produce the longest possible battery life. Maximum Performance Profile The Maximum Performance profile is a combination of timeouts and other power savings parameters selected by Fujitsu as the settings that will produce superior performance with reasonable battery life. Presentation Profile The Presentation profile is the same combination of timeouts and other power savings parameters as the Maximum Battery Life profile except that the display is never turned off. (This profile was designed to enhance the use o f the notebook for slide show style presentations.) On Off Figure 2-5 Power Switch Suspend Mode Activation Pressing the Suspend Mode button turns off power to the all of the notebook except RAM. Pressing the Suspend/Resume Button turns the power back on and lets you begin where you left off. (See Figure 1-5 on page 5 and text on pages 4, 37­39 and 70­71.) 21 Section Two Save-to-Disk Mode Activation Pressing the Save-to-Disk Mode button will cause all of RAM to be stored in the Save-toDisk space on the hard drive and the notebook to shutdown. Shutdown turns off all notebook power. If the Power Switch is not turned off the notebook can be restarted by pressing the Suspend/Resume Button which will cause the RAM to reloaded,letting you begin where you left off. (See Figure 1-5 on page 5 and text on pages 4, 37­39 and 70­71.) Video Standby Mode Activation Pressing the Video Standby Mode button toggles the enable/disable feature for the display time-out. When disabled only the Suspend Mode or the Standby Mode will turn off the display, the video time-out setting will be ignored. (See pages 41 and 70­71.) PC Card Control Pressing the PC Card Control button accesses a dialog box which allows you to view the properties of the PC Card installed in each slot and enable or disable each card. When you turn on your notebook be sure you have a power source. This means that the battery is installed and charged, or that the AC Adapter or the Auto Adapter is connected and has power. Power On Facing the Keyboard and Built-in Display, move the Power Switch towards the rear of your notebook. This is the On position. (See Figure 2-5.) When you are done working you can leave your notebook in Suspend Mode, (see pages 39 and 71), or you can turn it off. The Power Switch moved toward the front of your notebook is in the Off position. See the section Power Off, (page 23), for recommended shutoff procedures. CAUTION When the power is On, do not carry your notebook around, or subject it to shocks or vibration, as you risk damaging your notebook. CAUTION The Nickel Metal Hydride Battery Pack is not charged when you purchase your notebook. Initially you will need to connect the AC Adapter to use it. CAUTION After turning your notebook off, make sure that it has been off at least 10 seconds before turning the Power Switch to On. If you do not, it could cause a system error. 22 LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series When the Power Switch is turned On, your notebook carries out a Power On Self Test to check the internal parts and configuration. If a fault is found a beep will sound and/or an error message will be displayed. (See Troubleshooting on pages 92­115.) Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the Setup Utility and revising the settings. After satisfactory completion of the Power On Self Test your notebook will load the operating system. (See Boot Menu on pages 73­74 to see which kind of disk will be the source.) Special Operating System Features Every Windows desktop has some standard icons. To learn about these icons see the Windows manual or help screens. Your notebook desktop has some icons, such as a Fujitsu Icon, which are not standard Windows Icons. You can click on each one to see what is controlled. It will vary for different models. Some special control features of your notebook are accessed from icons on the Windows Control Panel: PC Card control; TouchPad cursor control adjustments; multimedia controls; and others. Using the Fujitsu Icon The Fujitsu Icon has product registration forms and instructions, change of address information and forms, contact information including telephone numbers and e-mail addresses and an accessory catalog with the information for ordering accessories for your notebook. Double click on the Icon and then on the selection you wish. Power Off Before turning off the power by putting the Power Switch in the Off position, check that the Hard Disk,CD-ROM,PC Card and the Floppy Disk Access Indicators are all Off. (See Figure 2-3, page 17.) If you turn off the power while accessing a disk or PC Card there is a risk of loss of data. The Off position is reached by facing the Keyboard and Built-in Display and moving the switch toward the front of your notebook. To assure that your notebook shuts down without error, use the shutdown sequence for the operating system. CAUTION Never turn your notebook off while an application is running. Be sure to close all files, exit all applications and shutdown the operating system prior to turning off the power with the Power Switch. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors. 23 CAUTION Never turn off your notebook during Power On Self Test or it will cause an error message to be displayed when you turn your notebook on the next time. (See the Trouble-shooting information on pages 112­115.) Section Two Shutting down your notebook from the operating system lets it close down operations and turn off the power in the proper sequence to prevent errors. The sequences are: Windows 95 1. Go to the Start Button Menu. 2. Click on Shutdown. 3. Verify that Shutdown is selected and click on YES. POINT If you do not turn the Power Switch to Off after shutting down you must use the use the Suspend/Resume Button to turn on your notebook as the Power Switch will already be in the On position. Windows 3.1 1. Save all data and exit all applications. 2. Exit Windows. 3. When the MS-DOS prompt appears put the Power Switch in the Off position. MS-DOS 1. Save all data and exit all applications. 2. When the MS-DOS prompt appears put the Power Switch in the Off position. If you are going to store your notebook for a month or more,take the following precautions: s s Windows 95 1.Go to the Start Button Menu. 2. Click on Restart the computer? 3. Verify that Restart the computer? is selected and click on YES. Windows will shutdown and restart your notebook. NOTE: You may also select Shut down the computer? and once the Power is off for 10 seconds or more you can restart your notebook with the Resume Button. You may also select Shut down the computer?nd once the a Power is Off turn the Power Switch to Off for 10 seconds or more and then turn the Power Switch to On. These alternative methods are not recommended. POINT In Windows 95 pressing the Ctrl+Alt+Del keys simultaneously triggers the Shutdown submenu of the Start Button Menu. Remove any CD and/or floppy disk. Turn off your notebook using the Power Switch. Close the notebook lid. Disconnect the AC Adapter. Remove the battery and store it separately in a cool dry place. s s s Restarting the System When you wish to restart the system be sure that you follow the appropriate procedure for the operating system. The procedures are as follows: 24 LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series Windows 3.1 1. Save all data. 2. Exit all applications. 3. Exit Windows. 4. When the MS-DOS prompt appears press the Ctrl+Alt+Del keys simultaneously. Or, when the MS-DOS prompt appears put the Power Switch in the Off position for 10 seconds or more and then put the Power Switch in the On position. MS-DOS 1. Save all data. 2. Exit all applications. 3. When the MS-DOS prompt appears press the Ctrl+Alt+Del keys simultaneously. Or, when the MS-DOS prompt appears put the Power Switch in the Off position for 10 seconds or more, and then put the Power Switch in the On position. s CAUTION Turning off the Power Switch without exiting Windows 95 may cause an error when you start the next time. Turning the power to On when it has been Off for less than 10 seconds may also cause an error when you start the next time. s The battery charging capacity is reduced as the battery ages. If the battery is running low quickly, you should replace it with a new one. When using a high cur rent device such as a modem, a LAN card,the CD-ROM drive, or the hard drive frequently. Battery The Nickel Metal Hydride Battery Pack is a rechargeable battery with an operating time of up to 2 hours depending on active Power Savings features and user activity levels. The battery operating time may become shorter than the reference value if it is used under the following conditions: s Using the AC Adapter will conserve the battery when using a high current device such as a modem, a LAN card, the CD-ROM drive, or the hard drive frequently. CAUTION Actual battery life will vary based on screen brightness, applications, features, power management setting, battery conditioning, and other customer prerences. CD-ROM or hard drive usage may also have a significant impact on battery life. When used at temperatures that exceed a low of 5°C or a high of 35°C. High temperatures not only reduce charging efficiency, but can also cause battery deterioration. (The charging icon on the Status Indicator Panel will flash when you try to charge a battery that is outside its operating temperature range.) 25 Section Two CAUTION Do not leave a faulty battery in your notebook. It might damage the AC Adapter, optional Auto Adapter, or your notebook itself. It may also prevent operation of your notebook by draining all available current into the bad battery. Shorted Battery If the Status Indicator shows a shorted battery, check the installation by removing and reinstalling it. If it still shows that it is shorted, replace it with a new battery. Recharging the Battery If you want to check the condition of the Nickel Metal Hydride Battery Pack, check the Battery Status Indicator located on the Status Panel. This indicator changes as the battery level changes. Battery 0 is the Nickel Metal Hydride Battery Pack. (See Figure 2-3 on page 17. ) You can also check the Power Management Controls. The battery is recharged internally using the AC Adapter or Auto Adapter. To recharge the battery: Make sure the battery to be charged is installed in your notebook and connect the AC Adapter or Auto Adapter. During charging, an arrow is displayed just to the left of the battery icon on the Status Indicator. The percentage charge is also shown inside the Battery Icon. (See Figure 2-4 on page 18.) The charging time from fully discharged is up to approximately 3 hours when your notebook is Off or in Suspend Mode. The charge times will be significantly longer if your notebook is in use while the battery is charging (up to approximately 9 hours with normal operating levels). CAUTION Using heavy current devices such as LAN cards or frequent CD-ROM accesses may prevent charging completely. Switching From AC Adapter To Battery Power 1. Be sure that you have a charged battery installed. 2. Remove the AC Adapter. Low Battery State When the battery is running low, your notebook beeps about every 15 seconds and the Battery Status Indicator flashes. If you do not respond to the low battery alarm, the battery will continue to discharge until it is too low to operate. When this happens there will be a multiple beep alarm, CAUTION Under federal, state or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at 1-800-8FUJITSU (1-800-838-5487). 26 LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series the Status Indicator will show dead battery, and your notebook will go into Suspend Mode to try and protect your data as long as possible. The Power Savings settings do not affect whether the dead battery alarm level will send your notebook into Suspend Mode. (See Figure 2-3 on page 17.) When the low battery alarm occurs you need to save all your active data and put your notebook into Suspend Mode until you can provide a new power source. You should provide this power as soon as possible. The new power source can be a charged battery or a power adapter, either AC or Auto. CAUTION When you are in Suspend Mode there must always be at least one power source active at all times. If you turn off the power with the Power Switch, or remove all power sources, Main Battery, AC Adapter or Auto Adapter, while your notebook is in Suspend Mode any data which has not been saved to disk will be lost. Once your notebook goes into Dead Battery Suspend Mode you will be unable to resume operation until you provide a source of power either from an AC Adapter, or an optional Auto Adapter. Dead Battery Suspend Mode shows on the Status Indicator just like the normal Suspend Mode .O n ce you have provided power, you will need to press the Resume Button to resume operation. In the Suspend Mode, your data can be maintained for sometime. If a power source is not provided promptly, the Power Indicator will stop flashing and go out, and you will have lost the data that was not stored. Once you provide power you can continue to use your notebook while an adapter is charging the battery, but the battery trickle charges under these conditions. If you want to charge the battery more quickly, put your notebook into Suspend Mode, or turn it off, while the adapter is charging the battery. (See Power Off on page 23 for shutdown procedures.) CAUTION There is no guarantee that data will not be lost once your notebook enters the Dead Battery Suspend Mode. CAUTION You may not be able to hear the audio alarms if the volume control is set too low, or is turned off by either hardware or software, but you will still be able to see the Battery Status Indicator flash. 27 Section Two Integrated TouchPad Pointing Device The TouchPad pointing device is composed of a small rectangular touch sensitive pad and two buttons located in front of the keyboard. The TouchPad pointing device has the function of a mouse,and moves the cursor around on the screen ­ up, down,left and right.A light pressure with the tip of your finger is all that is required to operate the pad. Pencil erasers, etc. do not work. The faster you move your finger the faster the cursor will move. The second part of the TouchPad pointing device ­ the buttons ­ function as mouse buttons, and the functions they perform depend on the application you are running. Figure 2-6 shows the position of the pointing device and mouse buttons. POINT The left (primary) mouse button functions can also be performed with your finger on the TouchPad. You can disable the TouchPad actuation of the button functions. (See TouchPad Pointing Device Adjustments on page 29.) Left Button Touch Sensitive Pad Right Button Figure 2-6 TouchPad Pointing Device POINT An external mouse can be connected to the PS/2 Connector on the right side of your notebook, and used at the same time as the Internal TouchPad Pointing Device. 28 Clicking Clicking means pushing and releasing a releasing a button. To left-click (primary-click) move the screen cursor to the item you wish to select, press the left (primary) pointing device button once,and then immediately release it. To rightclick, move the mouse cursor to the item you wish to select, press the right pointing device button once so that it makes a clicking sound, and then immediately release it.(Figure 2-7.) You can also left (primary) click by a light tap ending with the finger off the pad,instead of using the button. LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series Pad Clicking CAUTION If the interval between clicks is too long, the double-click will not be executed. POINT Button Clicking The interval between taps for double clicking, and other parameters of pointing and selecting, can be adjusted with the selections in the menu of the Mouse Icon in the Windows Control Panel. Figure 2-7 Clicking Button Dragging Pad-only Dragging Dragging Dragging means selecting an item with the pointing cursor, and while keeping the left (primary) pointing device button depre s s ed ,m oving the cursor to the desired location, then releasing the button .( F i g u re 2-8.) Dragging can also be done on the TouchPad without use of the button ­ two light taps ending with the finger on the pad and then moving. The function of dragging can be can be adjusted from the Mouse Icon in the Windows Control Panel. TouchPad Pointing Device Adjustments The built-in pointing device parameters are controlled by the Mouse Icon in the Control Panel. The mouse driver allows you to tailor the operation to suit your personal taste. The aspects of the TouchPad Pointing Device operation which you can adjust are: s Double-Clicking Double-clicking means following the Clicking procedure above, but pressing the pointing device button twice in rapid succession. Double click works with either the left or the right button. Double left (primary) clicking can be done on the touch pad, instead of using the button. It is similar to single left clicking using the touch pad ­ two light taps ending with the finger off the pad. Buttons ­ Allow you to adjust the interval between clicks that will be recognized as a double-click and also to set the b utton for left or right-handed primary operation. Pointers ­ Allow you to select the look of the cursor during various functions. 29 s Figure 2-8 Dragging Section Two You may want to try practicing with different adjustments until you find a combination that is comfortable for you. Figure 2-10 Cursor Keys Using the Keyboard Your notebook has an integral 86-key keyboard. (Figure 2-9.) The keys perform all the standard functions of a 101-key keyboard and also include Windows 95 keys and other special function keys. This section describes only those items specific to your notebook. They are the numeric keypad, the cursor keys, the function keys, the function extension key and the Windows 95 keys. Figure 2-9 Numeric Keypad Function s Motion ­ Allows you to set the sp eed of the cursor relative to the speed of your finger movement and whether to show a t rail as the cursor moves. TouchPad ­ Allows you to set what functions in addition to cursor movement can be performed on the TouchPad without use of the buttons. s s General ­ Lets you select the type of mouse. Your TouchPad is a Standard PS/2 Port Mouse and the port for external mouse connection is a Standard PS/2 Port. Use the Help Button in the lower right corner of the dialog box for additional guidance in setting up your TouchPad features. 30 LifeBo ok 400 Series from Fuji tsu Using Your LifeBook 400 Series Numeric KeyPad Certain keys on the keyboard perform dual functions as both standard character keys and as a numeric keypad.Figure 2-9 highlights these keys. To switch into numeric key pad mode, press the Num Lk while holding down the Shift key. You can now enter numerals 0 through 9, perform addition ( + ), subtraction ( ­ ), multiplication ( * ), or division ( / ),and enter decimal points ( . ) using the keys designated as ten-key functions. The keys in the numeric keypad are marked in the lower right corner of the key to indicate their secondary functions. To return these keys to their normal character function, press the Num Lk while holding down the Shift key again. Cursor Keys The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up , down , left and right as the application allows. Pressing F5 while holding down the Fn key allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with less than 800 x 600 pixel resolution will still cover the entire screen.) Pressing F10 while holding down the Fn key allows you to change your selection of where to send the display video. Each time you press the combination of keys you will step to the next choice. The choices,in order, are: built-in LCD only, external CRT only, or both LCD and CRT. Windows 95 Keys Your notebook has three Windows 95 keys, two Start keys and an Application key. The Start key displays the Start Button Menu, when in Windows 95. This is the same as the button on the toolbar which is typically at the bottom of the Windows 95 screens. The Application key has the same function in Windows 95 as the right mouse button, it displays the Shortcut Menu for whatever item is selected. See the Windows 95 documentation for additional information. 31 POINT The Integrated TouchPad Pointing Device and/or an external mouse are also used for moving the cursor around the screen. Function Keys Your notebook has twelve function keys, F1 through F12. The functions assigned to these keys differ for each application, and you should refer to the software documentation to find out how these keys are used. Fn Key The Fn key provides two extended functions for your notebook and is used in conjunction with other keys. POINT When an external keypad is connected to your notebook the NumLock Mode enables the external keypad and disables the built-in keyboard numeric keypad. Section Two CAUTION The optional External Floppy Disk Adapter is for use with the Removable Floppy Disk Drive only. Installing any other module in the Adapter may damage the module, your notebook, or the Adapter. Floppy Disk Drive