User manual FUJITSU 770TX

COPYRIGHT Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu and the Fujitsu logo are registered trademarks and LifeBook is a trademark of Fujitsu Limited. Built for Humans and ErgoTrac are trademarks of Fujitsu PC Corporation. The following are registered trademarks of IBM Corporation:IBM, IBM PC AT, IBM PS/2. The following are registered trademarks of Microsoft Corpora ti on :M S ,M S - DO S , Windows 95. PCMCIA is a trademark of the Personal Computer Memory Card International Association. Phoenix and the Phoenix logo are registered trademarks of Phoenix Technologies,Ltd. Intel and Pentium are registered trademarks and MMX technolory is a trademark of Intel Corporation. PC-Doctor is a trademark of watergate.software.inc. SoftPEG is a registered trademark of CompuCore Multimedia Inc. LapLink is a registered trademark of Traveling Software Inc. AudioRack is a registered trademark of ESS Technology, Inc. MegaPhone is a registered trademark of AVEO, Inc. All other trademarks mentioned herein are the property of their respective owners. We cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. © Copyright 1998 Fujitsu PC Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu PC Corporation. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu PC Corporation. D E C LA RATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Fujitsu PC Corporation Address: 598 Gibraltar Drive Milpitas,CA 95035 Telephone: (408) 935-8800 Declares that product: Model:LifeBook 770Tx. LifeBook 790Tx. Complies with Part 15 of the FCC Rules. This device complies with Part 15 of the FCC rules. Operations is subject to the following two conditions: (1) This device must not be allowed to cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation. David Woo FULL NAME Fujitsu COMPANY 4/17/98 DATE CAUTION Changes or modification not expressly approved by Fujitsu PC Corporation could void this user's authority to operate the equipment. Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone Network The LifeBookTM 700 Series notebook computers are supplied with an internal modem which complies with Part 68 of the FCC rules.On this notebook is a label that contains the FCC Registration Number and the Ringer Equivalence Number (REN) for this equipment among other information. If requested, the user must provide their telephone company with the following information: 1. The telephone number to which the notebook is connected. 2. The Ringer Equivalence Number (REN) for this equipment. 3. That the equipment requires a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant. 4. The FCC Registration Number. This equipment is designed to be connected to the telephone network or premises wiring using a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant and a line cord between the modem and the telephone network with a minimum of 26AWG. FCC NOTICES Notice to Users of Radios and Television These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi on s ,m ay cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s s The REN is used to determine the number of devices that you may connect to your telephone line and still have all of those devices ring when your number is called. Too many devices on one line may result in failure to ring in response to an incoming call. In most, but not all ,a reas the sum of the RENs of all of the devices should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the RENs, contact your local telephone company. If this equipment causes harm to the telephone network, your telephone company may discontinue your service temporarily. If possible,they will notify you in advance. If advance notice is not practical they will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC. This fax modem also complies with fax branding requirements per FCC Part 68. Your telephone company will probably ask you to disconnect this equipment from the telephone network until the problem is corrected and you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service telephones provided by your telephone company. Connection to party lines is subject to state tariffs. Contact your state's public utility commission,public service commission or corporation commission for more information. s s Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet that is on a different circuit than the receiver. Consult the dealer or an exp erienced radio/TV technician for help. This equipment includes automatic dialing capability. When programming and/or making test calls to emergency numbers: Remain on the line and b riefly explain to the dispatcher the reason for the call. s Perform such activities in off-peak hours, such as early morning or late evening. FCC rules prohibit the use of non-hearing aid compatible telephones in the following locations or applications: s s s s Public transportation terminals where telephones are used to call taxis or to rese rve lodging or rental cars. In hotel and motel rooms as at least ten percent of the rooms must contain hearing aid compatible telephones or jacks for plug-in hearing aid compatible telephones which will be provided to hearing impaired customers on request. DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada. Notice to Users of the Canadian Telephone Network The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. The LifeBook 700 Series notebook computers are supplied with an internal modem which complies with the Industry Canada certification standards for telecommunication network protection and safety requirements. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations. Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by FujitsuTM PC Corporation or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line. The connecting arrangement code for this equipment is CA11A. The Load Number is 3. The Load Number assigned to each telephone terminal device denotes the percentage of the total load to be connected to a telephone loop or circuit which is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices such that the total of the load numbers of all devices does not exceed 100. s s s s s s All public or semipublic coin-operated or credit card telephones. Elevators ,h i ghways, tunnels (automobile, subway, railroad or pedestrian) where a person with impaired hearing might be isolated in an emergency. Places where telephones are specifically installed to alert emergency authorities such as fire, police or medical assistance personnel. Hospital rooms, residential health care facilities, convalescent homes and prisons. Workstations for the hearing impaired. Hotel,motel or apartment lobbies. Stores where telephones are used by patrons to order merchandise. CAUT ION For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician. This may be particularly important in rural areas. Avis Aux Utilisateurs Du Réseau Téléphonique Canadien L'étiquette canadienne Industrie Canada identifie l'équipement certifié. Cette certification signifie que l'équipement satisfait certaines normes de protection,d'exploitation et de sécurité des réseaux de télécommunications. Le département ne garantit pas le fonctionnement de l'équipement à la satisfaction de l'utilisateur. La série LifeBookTM 700 possède un modem interne conforme aux normes de certification d'Industrie Canada pour protéger les réseaux de télécommunications et satisfaire aux normes de sécurité. Avant de connecter cet équipement à une ligne téléphonique,l'utilisateur doit vérifier s'il est permis de connecter cet équipement aux installations de télécommunications locales. L'utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service. Les réparations de l'équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n'est pas expressément approuvée par Fujitsu PC Corp., ou toute défaillance de l'équipement peut entraîner la compagnie de télécommunications à exiger que l'utilisateur déconnecte l'équipement de la ligne téléphonique. Le code d'arrangement de connexion de cet équipement est CA11A. Le numéro de charge est 3. Le numéro de charge assigné à chaque terminal téléphonique indique le pourcentage de la charge totale pouvant être connecté à une boucle ou à un circuit téléphonique, utilisé par ce périphérique afin de prévenir toute surcharge. La terminaison d'une boucle peut être constituée de n'importe quelle combinaison de périphériques de sorte que le total de numéros de charge de tous les périphériques n'excède pas 100. AVERTISSEMENT UL NOTICE (FOR AUTHORIZED REPAIR TECHNICIANS ONLY) CAUTION: For continued protection against risk of fire, replace only with the same type and rating fuse. CAUTION:Danger of explosion if CMOS battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instruction. WARNING: CMOS and NiCAD batteries may explode if mistreated. Do not recharge,disassemble or dispose of in fire. Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d'électricité, les lignes télphoniques et les conduites d'eau métalliques sont connectées ensemble. Les utilisateurs NE doivent PAS tenter d'établir ces connexions eux-mêmes, mais doivent contacter les services d'inspection d'installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales. Table of C ontents Table of Contents PREFACE . . . . . . . . . . . . . . . . . . vi SECTION TWO USING YOUR LIFEBOOK 700 SERIES FROM FUJITSU Display Panel . . . . . . . . . . . . . Adjusting the Keyboard Angle . . . . Status Indicator Panel . . . . . . . . . Power On . . . . . . . . . . . . . . . Power Off . . . . . . . . . . . . . . . Restarting The System. . . . . . . . . Batteries . . . . . . . . . . . . . . . . Fujitsu Welcome Center . . . . . . . . Integrated ErgoTrac Pointing Device . Using The Keyboard. . . . . . . . . . Volume Control . . . . . . . . . . . . Floppy Disk Drive . . . . . . . . . . . CD-ROM Drive . . . . . . . . . . . . Hard Drive . . . . . . . . . . . . . . . Power Management . . . . . . . . . . Internal Modem . . . . . . . . . . . . Infrared Port . . . . . . . . . . . . . . Pre-Installed Software . . . . . . . . . Agaté Tioman ProSwap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 19 19 23 24 25 26 26 30 32 34 34 36 38 38 47 47 48 50 SECTION THREE CONFIGURING YOUR LIFEBOOK 700 SERIES FROM FUJITSU Boot Sequence . . . . . . . . . . . . . . . . . 54 Identifying the Drives . . . . . . . . . . . . . 54 BIOS Setup Utility. . . . . . . . . . . . . . . 55 Navigating Through the Setup Utility . . . . 57 Main Menu ­ Setting Standard System Parameters . . . . . . . . . . . . . 58 Advanced Menu ­ Setting Device Feature Controls . . . . . . . . . . . . . . 67 Security Menu ­ Setting the Security Features . . . . . . . . . . . . . . 89 Power Menu ­ Setting Power Management Feature Controls. . . . . . . 95 Boot Menu ­ Selecting the Operating System Source . . . . . . . . . 103 Info Menu ­ Displaying Basic System Information . . . . . . . . . . . . 107 Exit Menu ­ Leaving the Setup Utility . . . 109 Setting Up Your Save-to-Disk File Allocation . . . . . . . . . . . . . . . 112 SECTION ONE SETTING UP YOUR LIFEBOOK 700 SERIES FROM FUJITSU Unpacking. . . . . . . . . . . . . . . . . . . . 2 Overview of Lifebook 700 Series Features . . . 4 Component Identification . . . . . . . . . . . 6 Top and Front Components . . . . . . . . . . 7 Left-side Panel Components . . . . . . . . . . 8 Right-side Panel Components . . . . . . . . . 8 Rear Panel Components . . . . . . . . . . . . 9 Bottom Components . . . . . . . . . . . . . 11 Power Sources . . . . . . . . . . . . . . . . . 11 Data Security . . . . . . . . . . . . . . . . . 12 Starting Your Notebook for the First Time. . 13 User Registration . . . . . . . . . . . . . . . 15 Learning About Your Operating System and Application Software. . . . . . . . . . 16 ii LifeBook 7 00 Series from Fujitsu Table of Contents SECTION FOUR USER INSTALLABLE FEATURES Multi-function Bay Devices PC Cards . . . . . . . . . . Parallel Port Devices . . . . Serial Port Devices . . . . . USB Devices . . . . . . . . Microphone . . . . . . . . Stereo Line In Devices . . . Headphones . . . . . . . . Telephone Lines . . . . . . Mouse or Keyboard . . . . External Monitor . . . . . . Theft Prevention Lock . . . External Installation of a Floppy Disk Drive . . . . Memory Upgrade Module . LANdock . . . . . . . . . . Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 124 126 126 126 126 126 126 127 127 127 127 128 129 132 136 SECTION FIVE TROUBLESHOOTING Identifying the Problem . . . . . . . . . . Specific Problems . . . . . . . . . . . . . Power On Self Test Messages . . . . . . . Emergency CD-ROM Drive Tray Release . Modem Setup and Commands . . . . . . Restoring Your Pre-Installed Software from CD-ROM . . . . . . . . . . . . . 138 139 158 161 161 APPENDIX A SPECIFICATIONS Warranty . . . . . . . . . . . . Lifebook 770Tx Specifications. Lifebook 790Tx Specifications. Approvals . . . . . . . . . . . . Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 168 171 175 175 APPENDIX B GLOSSARY Glossary. . . . . . . . . . . . . . . . . . . . 176 . 162 SECTION SIX CARE AND MAINTENANCE Caring for your Notebook . . . . . . . . . . 164 Increasing Battery Life . . . . . . . . . . . . 165 Caring for Your Batteries . . . . . . . . . . 165 INDEX Index . . . . . . . . . . . . . . . . . . . . . 183 iii Preface Li feB oo k 7 0 0 Se ries fr om Fujit su Preface PREFACE The LifeBook 700 Series from Fujitsu PC Corporation is a powerful notebook computer. It is powered by an Intel Pentium microprocessor with MMX technology, has a built-in color display, a CD-ROM drive and brings the computing power of desktop personal computers (PCs) to a portable environment. This manual explains how to operate your LifeBook 700 Series' hardware and built-in system software. The LifeBook 700 Series is compatible with the IBM ® PC AT. It comes with Windows 95 pre-installed. A LifeBook 700 Series is a completely selfcontained unit with an active-matrix (TFT) color LCD display. It has a powerful interface that enables it to support a variety of optional features. (Figure P-1.) CONVENTIONS USED IN THE GUIDE Screen examples in this manual are intended as examples only, and screen and file names may differ in actual use. Messages displayed by the LifeBook 700 Series appear in Courier type. Example: Shutdown the computer? Keyboard keys are shown in boldface Helvetica type. Example: Fn, F1, Esc, and Ctrl. Pages with additional information about a specific topic are cross-referenced within the text. Example: (See page xx.) POINT The point icon highlights information that will enhance your understanding of the subject material. CAUTION The caution icon highlights information that is important to your safety, to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully. vi LifeB ook 70 0 Series from Fuj itsu Lif eBook 700 Series f rom Fujitsu Figure P-1 LifeBook 700 Series with Both Fujitsu and Third Party Options vii Section S et tin g U p Yo u r Li f eB oo k 7 0 0 Ser ie s Unpacking . . . . . . . . . . . . . . . . . . . 2 Overview of LifeBook 700 Series Features . . . 4 Component Identification . . . . . . . . . . . 6 Top and Front Components . . . . . . . . . . 7 Left-side Panel Components . . . . . . . . . . 8 Right-side Panel Components . . . . . . . . . 8 Rear Panel Components . . . . . . . . . . . . 9 Bottom Components . . . . . . . . . . . . . 11 Power Sources . . . . . . . . . . . . . . . . 11 Data Security . . . . . . . . . . . . . . . . . 12 Starting Your Notebook for the First Time . . 13 User Registration . . . . . . . . . . . . . . . 15 Learning About Your Operating System and Application Software. . . . . . . . . . 16 One Section One SECTION ONE SETTING UP YOUR LIFEBOOK 700 SERIES FROM FUJITSU This section describes how to set up your LifeBook 700 Series from Fujitsu. We strongly recommend that you read it before using your notebook ­ even if you are already familiar with notebook computers. s Modular 20-speed maximum CD-ROM drive.(Already installed in Multi-function Bay 2 of your notebook.) Modular 3.5" floppy disk drive (located in the accessories box). (Figure 1-4.) Device adapter for Multi-function Bay 2 (located in the accessories box.) (Figure 1-3.) RJ-11 cable (located in the accessories box). Getting Started Guide. User's Guide. Microsoft Windows 95 Manual. Registration card and customer information pack. Recovery CD-ROM (located in the accessories box). LANdesk Client Manager 3.2 CD-ROM (located in the accessories box). Figure 1-2 AC Adapter Unit Figure 1-1 LifeBook 700 Series Notebook s s s UNPACKING When you receive your notebook,unpack it carefully, and compare the parts you have received with the items listed below. For a standard configuration you should have: s s s s s LifeBook 700 Series from Fujitsu. (Figure 1-1.) AC adapter with AC power cord (located in the accessories box). (Figure 1-2.) Modular Lithium ion battery. (Already installed in Multi-function Bay 1 of your notebook.) s s s s 2 LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s Once you have checked and confirmed that your notebook system is complete, connect the AC adapter and follow the instructions on page 12-14 to accept the conditions for using the LifeBook 700 Series. When you have completed the Conditions of Use process please register your notebook. (See page 15.) Figure 1-3 Device Adapter for Multi-function Bay 2 Figure 1-4 Floppy Disk Drive 3 Section One OVERVIEW OF LIFEBOOK 700 SERIES FEATURES The LifeBook 700 Series is a compact, yet powerful notebook computer available with standard features including: (See Appendix A, pages 170-177, for detailed information on individual models.) s s 20-speed maximum CD-ROM drive (included with all models) (for Bay 2 only). Optional second 3.2GB hard drive (for Bay 2 only). Optional Zip drive. Lithium ion battery (one included with all models). Optional second Lithium ion battery. POINT The Multi-function bays are warmswappable with the Tioman ProSwap software. (see page 50) s s s 200MHz or 266MHz Intel Pentium processor with MMX technology. 32MB SDRAM standard, expandable to 96MB. 12.1" active-matrix (TFT) color display with 800 x 600 resolution. 2MB EDO video RAM. DMI 2.0 compliant. Built-in 3.2GB or 4.0GB hard drive. Multi-function Bays which support the following: s s CAUTION The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a digital PBX as it may cause serious damage to the internal modem or your entire notebook. Consult your PBX manufacturer's documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem. s s Internal 56K fax/data/voice modem with built-in telephony and DSVD support. CAUTION Your internal modem is designed to allow faster downloads from K56flex compliant digital sources. Maximum achievable download transmission rates may not reach 56kbps and will vary with line conditions. s s s s s 3.5" floppy disk drive (included with all models). 4 LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s s Full audio and video features: s s 16-bit SoundBlaster-compatible sound chip. 3D-Stereo for multiple speaker effect. Zoomed Video support for full motion video acceleration. Built-in stereo speakers. Built-in mono microphone. Stereo line in jack. Stereo headphone jack. Microphone jack. "No re-learning", full-size keyboard with three dedicated Windows 95 keys. Hot swap connection for an external keyboard or an external mouse. USB device support. Bridge battery for warm-swapping capabilities for batteries. Standard pre-installed software: s s s s s s s Display Latch Multi-function Bay Power Port Power Switch PS/2 Port Figure 1-5 Top and Front Panel s s s s s s s s Microsoft Windows 95 operating system. LapLink for file transfer via modem,cable or infrared port. PowerPanel for system power management. Agate Tioman ProSwap for warm-swapping functionality in Multi-function bays. PC-Doctor for system diagnostics. SoftPEG from CompCore,an MPEG-1 video player. McAfee VirusScan for virus protection. s s s ESS AudioRack for 3D-Stereo, audio CD and other audio controls. MegaPhone for telephone applications including fax,dialing, and speakerphone. AT&T WorldNet Service. AOL 3.0. Netscape Communicator 4.04. Internet Explorer 4.01. s s Two Type II/one Type III PC Card slot. Fast IrDA (4Mbps) compatible infrared port for wireless data transfer. Integrated ErgoTrac pointing device for superb comfort and cursor control. TM Standard user-install software: s s s s s s s s External monitor support with simultaneous display capabilities. s 5 Section One COMPONENT IDENTIFICATION For detailed specifictions on each model refer to Appendix A on pages 170­177. Display Panel Display Panel Latch Status Indicator Panel Brightness Control Keyboard Built-in Microphone ErgoTrac pointing device Suspend/Resume Button TM Multi-function Bay 1 Closed Cover Switch Multi-function Bay 2 6 Figure 1-6 LifeBook 700 Series with Display Open LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s TOP AND FRONT COMPONENTS Display Panel Latch This latch locks and releases the display panel. When the display panel is released it pops up slightly to make it easier to o pen. (Figure 1-6.) Display Panel This is a color LCD panel with back lighting for the display of text and graphics. (Figure 1-6.) Brightness Control The brightness control adjusts the overall intensity of the display panel back lighting. (Figure 1-6.) Built-in Microphone The built-in microphone allows mono audio input to your notebook. (Figure 1-6.) Status Indicator Panel An LCD display of the status of the power state and source, Suspend mode,battery charge (battery in either Multi-function Bay), floppy disk drive activity, hard drive or zip drive activity, CD-ROM drive activity, PC Card activity, CapsLock, NumLk and Scr Lk. (Figure 1-6.) Suspend/Resume Button The Suspend/Resume button allows you to suspend notebook activity without turning off the notebook power, and to return it to an active state. This feature saves power, and is particularly useful when the notebook is running only on battery power. (See pages 38-46 and 95-102 for more information on power management.) (Figure 1-6.) Closed Cover Switch The closed cover switch turns off the LCD back lighting when the display panel is closed, thus saving power. This switch also behaves as a Suspend/Resume button, when the closed cover switch is set to Suspend/Resume in the BIOS Setup Utility. (see pages 95-102 for more information on the BIOSSetup Utility) (Figure 1-6.) CAUTION Be sure you know which settings are active for your Suspend/Resume button before you use it because misuse can result in data loss. (See the Power Savings Menu of the BIOS setup utility, pages 95-102, for more information.) Keyboard A full-size keyboard with dedicated Windows 95 keys for input into the notebook. (Figure 1-6.) ErgoTrac Pointing Device The ErgoTrac pointing device is a joystick-like cursor control system with two click buttons. (Figure 1-6.) Multi-function Bay One This bay accommodates: s s s Lithium ion battery. Optional Zip Drive 3.5" floppy disk drive. 7 Section One Multi-function Bay Two This bay accommodates: s s PC Card Eject Buttons RIGHT-SIDE PANEL COMPONENTS Theft Prevention Lock Slot This is a slot that allows you to attach a physical lock down device. (Figure 1-8.) USB Port This port allows you to connect Universal Serial Bus devices, such as external game pads, pointing devices, keyboards and speakers. (Figure 1-8.) 20-speed maximum CD-ROM drive. Optional Zip drive mounted in the device adapter for Multi-function Bay 2. Lithium ion battery mounted in the device adapter for Multi-function Bay 2 (a second battery can be purchased separately for a dual battery configuration). Optional second 3.2GB hard drive (which must be purchased separately). 3.5" floppy disk drive mounted in the device adapter for Multi-function Bay 2. CAUTION Do not use your notebook with either of the Multi-function bays empty. It may damage your notebook. PC Card Lock PC Card Slots Left Speaker s Figure 1-7 LifeBook 700 Series Left-side Panel s s DC Power Jack LEFT-SIDE PANEL COMPONENTS The DC power jack allows you to plug in the PC Card Slot AC adapter or the optional auto/airline adapter. The PC Card Slot allows you to install two Type (Figure 1-8.) I or Type II PC Cards or one Type III PC Card. (See pages 124-126 for more information on PC Stereo Line Cards.) The button to the left of the card slot External Floppy In Jack Disk Drive Port Theft Prevention locks the card(s) in place,and the buttons Lock Slot Headphone Jack Microphone to the right of the slot eject the card(s) from Jack Power Switch the slot. (Figure 1-7.) Volume Left Speaker The built-in dual speakers output stereo sound from the notebook. (Figure 1-7 and Figure 1-8.) Control PS/2 Port Port Cover Right Speaker DC Power Jack USB Port Figure 1-8 LifeBook 700 Series Right-side Panel 8 LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s Power Switch This switch is the main power switch for your notebook. (Figure 1-8.) Right Speaker The built-in dual speakers output stereo sound from the notebook. (Figure 1-7 and Figure 1-8.) External Floppy Disk Drive Port A port for attaching an optional external floppy disk drive. This allows you to connect an optional floppy disk drive when the Multifunction bays are being used for other purposes. (Figure 1-8.) PS/2 Port The port allows you to connect an external PS/2 keyboard,mouse, or numeric keypad. (Figure 1-8.) Microphone Jack The microphone jack allows you to connect an external mono microphone. (Figure 1-8.) Stereo Line In Jack The stereo line in jack allows you to connect an external audio source to your notebook,like an audio cassette player. This jack will not support an external microphone. (Figure 1-8.) Headphone Jack You can connect headphones or powered external speakers to the headphone jack. (Figure 1-8.) Volume Control The volume control is a knob which provides manual control of the sound level of all audio output from your notebook. (Figure 1-8.) CAUTION There are also software volume controls. The knob setting and the software settings will interact. Software volume off will override the knob setting and the software volume setting will control the maximum knob setting. (See Volume Control on page 34 for more information.) RJ-11 Jack Docking Port Serial Port Parallel Port External Monitor Port Slide Panel Connector Cover Infrared Port Figure 1-9 LifeBook 700 Series Rear Panel REAR PANEL COMPONENTS RJ-11 Jack This is the jack for attaching a telephone line to the internal modem. This jack can be used with the connector cover closed and the sliding panel in the connector cover slightly opened for added convenience. (Figure 1-9.) 9 Section One CAUTION The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a digital PBX as it may cause serious damage to the internal modem or your entire notebook. Consult your PBX manufacturer's documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem. Docking Port This port is for connection to an optional port replicator or docking station. The connector cover must be closed and the sliding panel fully opened to reveal the docking port and the RJ-11 jack when connecting a port replicator or a docking station. (Figure 1-9.) CAUTION The cover ­ which closes over the ports on the rear of the notebook ­ can be damaged if it is left open when the notebook is moved around. Serial Port The serial port allows you to connect serial RS-232C devices, such as serial printers or serial scanners. (This is also sometimes referred to as a COM port.) (Figure 1-9.) Parallel Port The parallel port allows you to connect parallel devices, such as a parallel printer to your notebook. (This is also sometimes referred to as a LPT port.) (Figure 1-9.) External Monitor Port This port allows you to connect an external VGA or SVGA CRT monitor. (Figure 1-9.) Infrared Port The fast IrDA (4Mbps) compatible port allows you to communicate with another IrDA compatible infrared device without a cable. (See page 47 for more information.) (Figure 1-9.) Docking Alignment Receptacle Tilt Adjustment Feet Docking Alignment Receptacle Memory Upgrade Compartment Main Unit and Configuration Label Multi-function Bay 2 Multi-function Bay 1 Multi-function Bay 2 Release Button Multi-function Bay 1 Release Button Figure 1-10 LifeBook 700 Series Bottom 10 LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s BOTTOM COMPONENTS Tilt Adjustment Feet These are a pair of feet which flip down and hold the back of the notebook approximately 6° higher than the front when resting on a flat surface. They are designed to make using your notebook keyboard more comfortable. (Figure 1-10.) Main Unit and Configuration Label This label shows the model number and other information about your notebook. In addition the configuration portion of the label has the serial number and manufacturer information that you will need to give your support representative so that he or she can help you. It identifies the exact version of various components of your notebook. (Figure 1-10.) Memory Upgrade Compartment This compartment houses the memory upgrade module which allows you to expand the system memory capacity of your notebook. (See pages 129-130 for more information on installing added memory capacit y.) (Figure 1-10.) Multi-function Bay 1 Release Button This is the release to allow removal and installation of devices in Multi-function Bay 1. (Figure 1-10.) Multi-function Bay 1 This compartment is accessed from the front of your notebook. (See Figure 1-6 on page 6.) Multi-function Bay 2 Release Button This is the release to allow removal and installation of devices in Multi-function Bay 2. (Figure 1-10.) Multi-function Bay 2 This compartment is accessed from the front of your notebook. (See Figure 1-6 on page 6.) Figure 1-11 Connecting the AC Adapter POWER SOURCES Your notebook has four possible power sources: the primary Lithium ion battery; an optional dual Lithium ion battery configuration; the AC adapter; or an optional auto/airline adapter. Connecting the Power Adapters The AC adapter or an optional auto/airline adapter provides power for operating your notebook and charging the batteries. (Figure 1-11.) To Connect the AC Adapter 1. Plug the DC Output cable of the AC adapter into the DC Power jack on the right-side panel of your notebook. Plug the AC adapter into an AC electrical outlet. 11 2. Section One To Connect the Optional Auto/airline Adapter 1. Plug the DC Output cable into the DC Power jack on the right-side panel of your notebook. Plug the auto/airline adapter plug into the cigarette lighter of a car or other vehicle with the ignition key in the On or the Accessories position or into the DC Power jack on an airplane seat. CAUTION The primary Lithium ion battery is not charged when you purchase your notebook. Initially you will need to connect the AC adapter or the auto/airline adapter to use it. If you purchase a second Lithium ion battery it will not be charged when you get it. You will need to charge it prior to use. It can take up to three (3) hours to charge a single battery if your notebook is turned off or is in Suspend mode. If your notebook is in use it can take up to nine (9) hours or more to charge a single battery. software control password security features that allow you to protect all or portions of the data stored in the notebook from unauthorized access. Hardware Data Security Features When you are using your notebook built-in hardware control password to gain access to the notebook the actual password will not appear on the screen. This is a safety precaution. The hardware control security parameters are set from the BIOS setup utility. (See Security Menu on pages 89-94 for more information on setting and clearing passwords and enabling and disabling built-in security features.) Software Data Security Features The operating system and some applications have security features that are independent of the built-in hardware protection features that are controlled from the BIOS. See your software documentation for more information about these features. 2. To Switch From AC Adapter Power To Battery Power 1. Be sure that you have at least one charged battery installed. 2. Remove the AC or auto/airline adapter. DATA SECURITY Your LifeBook 700 Series has a built-in hardware control password security feature that allows you to protect the data stored in the notebook from unauthorized access. Your operating system and some applications have 12 LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s CAUTION Make sure you memorize your passwords, both hardware and software. If you forget, you may not be able to use the notebook, and you will have to contact your service provider and arrange to have them reset the hardware system password. See your software documentation for what to do if you forget your software security password(s). STARTING YOUR NOTEBOOK FOR THE FIRST TIME Booting the System The first time that you turn on your notebook you will need to attach your AC adapter because the battery is not charged when you get your machine. We strongly recommend that you not attach any other external devices and do not put any CD or fl oppy disk in your drives until you have gone through the initial power on sequence. When you turn on your notebook for the first time it will display a Fujitsu logo on the screen. If you do nothing the system will read the hard drive for the operating system software, flash the notebook configuration information on the screen,and then the Windows 95 Setup Wizard Screen will appear. (See Power On on pages 2324 for additional help.) You will then be stepped through the condition of use process. You must complete this initial process before you will be able to use your notebook.(If you wish to access the BIOS setup utility before you go through the condition of use process you must press the F2 key while the Fujitsu logo is still visible. If you press the Esc key while the Fujitsu logo is still present you will get a dialog box which will allow you to sele ct which drive is to be used for finding the operating system.) If you turn off the power without using the on screen Cancel button you will get an error message when you start your notebook again. Conditions of Use Process The first time you start your notebook you must confirm your acceptance of the copyright limitations for your pre-installed software. After you complete the Condition of Use process these screens will not appear again. There are 6 screens to read carefully and respond to. You cannot use your notebook until this Condition of Use process is completed. The bottom of each screen has a Button and a Cancel button which are activated by the integrated ErgoTrac cursor control and button click. The button activates any choices or 13 CAUTION Software security feature passwords may not be the same as the hardware security passwords. Be sure you know which features are controlled from software and which from hardware or you may lock yourself out of your own data or lock up your hardware and not be able to operate your notebook. Section One information you have entered and takes you on to the next screen. The Cancel button allows you to stop the setup process. If you stop the process your notebook will start up at the b eginning of the Windows 95 Setup Wizard. The screens you will be required to respond to are described with the required action. User Information Fill in your name and your company name as you want the software licensed. To step from the name blank to the company blank press the Tab key. When the information has been entered click on the Next> button. You will not be allowed to continue until you make an ent ry. License Agreement Read the agreement carefully. You can scroll through the text using the integrated ErgoTrac pointing device to activate the scroll bar or use the up arrow and down arrow keys to move up and down the text one line at a time, or use the Page Up and Page Down keys to 14 move the text one screen at a time. When you finish reading you must point and click to accept or reject the terms of the agreement and then click on the Next> button. Start Wizard The Start Wizard screen will appear if you have entered a valid product code. When you click on the Finish button the display will flash various screens as the system identifies what hardware is installed and runs a virus check. Time Zone When your notebook has completely identified all of the installed hardware it will display a dialog box for entering which time zone you wish to set the clock to. Windows Messaging Once you have selected a time zone you will see a screen announcing that Windows messaging is being set up. Printer Setup When the messaging setup is complete a dialog box will appear for selecting which printer is to be attached to your notebook. You do not have to select a printer at this time. If you do not wish to select a printer, click on the Cancel button. If you do wish to sele ct a printer click on the Next button and answer the questions. POINT If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows 95 or to shut down your notebook. Certificate of Authenticity Look in the box that your notebook came in and you will find a Windows 95 Certificate of Authenticity shrink w rapped with the Windows 95 Users manual.On the certificate you will find a bar-code with a number above it. This is your product code and the number you should enter on the Certificate of Authenticity screen. When you have entered the number exactly as shown then click on the Next> button. LifeBook 7 00 Series from Fujitsu Se t t i n g U p Yo u r L i fe B oo k 70 0 Se r i e s Windows 95 Setup Once you have completed the printer setup, or if you have chosen not to set up a printer at this time, you will see the Windows 95 Setup screen. This screen lets you set up Internet Explorer 4.0 with Active Desktop on your Lifebook. Follow the on-screen direction to complete installation of IE 4.0 POINT If you would like to skip the installation of Internet Explorer 4.0, go the the Start Menu on the desktop, select Shutdown and Restart the computer. After returning to Windows, you can install Internet Explorer 4.0 at any time by selecting the icon Setup for Internet Explorer 4.0 in the Internet Starts Here folder on the desktop. POINT You will find a Recovery CD-ROM packet in your accessories box. Please store the packet in a safe place in case there is a loss of data, and it becomes necessary to re-install your operating system and/ or application programs. (See Restoring Your Pre-installed Software from the Recovery CD-ROM on pages 161-164.) REGISTERING YOUR LIFEBOOK What are the benefits of registering? You will receive an identification label for your LifeBook, which, if your LifeBook is ever lost, may help in getting it returned to you. You also receive priority Personal Identification Number (PIN) technical support access and useful product mailings. Proof of purchase is not required if you register within 30 days of your purchase. How do I register? By modem,fax,mail or telephone.To register your system by modem, with your system up and running, click on the Fujitsu Welcome Center Icon. Complete the electronic form and click on the "send registration" button. Your registration information will be t ransmitted via phone lines to the Fujitsu Registration Center and you will receive registration confirmation in one week to 10 days. You may also print your completed registration form and fax it to 1-714-450-9140 or mail it to: Fujitsu PC Corporation 15355 Barranca Pkwy, Irvine,CA 92618-9520 Alternately you may call: 1-800-8fujitsu (1-800-838-5487) 15 Section One LEARNING ABOUT YOUR OPERATING SYSTEM AND APPLICATION SOFTWARE Tutorials All operating systems and most application software have tutorials built-in. We highly recommend that you step through your tutorial before you use an application even if you are familiar with the same application on a different machine,an earlier version of the application, or a similar product. Manuals In the accessories box you will find manuals for Windows 95 and other pre-installed software. Software manuals of pre-installed software that are not in the accessories box are available online. See the help screens of your preinstalled software. We recommend that you review these manuals for general information on the use of these applications and to get a basic understanding of what is covered in the manual, and how it is organized, should questions arise as you use the applications. 16 Section Using Your LifeBook 700 Series from Fujitsu Display Panel . . . . . . . . . . . . . . . . . 18 Adjusting the Keyboard Angle . . . . . . . . 19 Status Indicator Panel . . . . . . . . . . . . . 19 Power On . . . . . . . . . . . . . . . . . . 23 Power Off . . . . . . . . . . . . . . . . . . 24 Restarting the System . . . . . . . . . . . . 25 Fujitsu Welcome Center . . . . . . . . . . . 26 Batteries . . . . . . . . . . . . . . . . . . . 26 Integrated ErgoTrac Pointing Device . . . . . 30 Using the Keyboard. . . . . . . . . . . . . . 32 Volume Control . . . . . . . . . . . . . . . . 34 Floppy Disk Drive . . . . . . . . . . . . . . . 34 CD-ROM Drive . . . . . . . . . . . . . . . . 36 Hard Drive . . . . . . . . . . . . . . . . . . 38 Power Management . . . . . . . . . . . . . 38 Internal Modem . . . . . . . . . . . . . . . 47 Infrared Port . . . . . . . . . . . . . . . . . 47 Pre-installed Software . . . . . . . . . . . . 48 Agaté Tioman Pro-Swap . . . . . . . . . . . 50 Two Section Two SECTION TWO USING YOUR LIFEBOOK 700 SERIES FROM FUJITSU This section describes the indicators, buttons, connections and operating modes of your LifeBook 700 Series and their use. Brightness Control Brighter Figure 2-1 Opening the Display Panel Less Bright DISPLAY PANEL Opening the Display Panel Lifting the latch releases the top of the display panel from the front of the notebook body. When the display panel is released it pops up slightly to make it easier to open. Lift the display panel backward until the screen is at a comfortable viewing angle. (Figure 2-1.) Adjusting the Display Panel When you turn on your notebook, you may want to adjust the brightness level of the screen for best visibility. To do this, adjust the brightness control slider on the right side of the display panel. (Figure 2-2.) You may need to adjust the brightness periodically for different operating environments. POINT The higher the brightness level, the more power the notebook will consume and the faster your batteries will discharge. For maximum battery life, make sure that the brightness is set as low as possible. Figure 2-2 Display Adjustments 18 LifeBo ok 700 Series from Fuji tsu Using Your LifeBook 700 Series ADJUSTING THE KEYBOARD ANGLE On the bottom of your notebook,near the back,are a pair of feet which flip down and hold the back of the notebook about 6° higher than the front when resting on a flat surfa ce. They are designed to make it more comfortable to use the keyboard with your notebook. The feet must be folded flat against the bottom of the notebook when opening or using the CD-ROM drive or it will not open or operate properly. (Figure 1-10 on page 10) CAUTION Do not operate your CD-ROM drive or attempt to open the tray unless your notebook is sitting on a flat surface and the adjustment feet are folded against the bottom of the notebook. Using a CD-ROM drive when it is not level may damage the drive or prevent proper operation. CAUTION When you are not using the adjustment feet be sure that they are folded flat against the bottom of the notebook. They could be broken off or injure someone if not used properly. POINT When your notebook has been shut down from Windows 95, it is not the same as turned off from the power switch. It is in a pseudo-off state, with all applications closed, but can be turned on by pressing the Suspend/Resume button. It is drawing some current in the pseudo-off state. STATUS INDICATOR PANEL The Status Indicator panel is located in the recess just above the keyboard. (Figure 2-3 on page 20.) The appropriate indicators become visible as you use your notebook. Power Indicator The Power indicator tells you when the system is operational. It is on steady when there is power to your notebook,and blinks when the system is in Suspend mode. It goes off when the system has entered Save-to-Disk mode,has entered the Windows 95 pseudo-off state, or the power is turned off from the power switch. CAUTION Your notebook's power switch must be turned off to prevent all current draw. 19 Section Two AC Adapter Indicator The AC Adapter indicator tells you whether the system is operating on an AC or auto/airline adapter, or batteries alone. The indicator is On when either of the adapters is active and Off when power comes from the batteries alone. If a battery is charging, the Power Adapter indicator is active regardless of the setting of the power switch. The AC Adapter indicator is also active in the Windows 95 pseudo-off state, regardless of the battery status. If there is no battery charging, and the power switch is Off,then the AC Adapter indicator and the Battery indicators will all be Off. Power Battery Identifier AC Adapter Battery Charging Battery Level CD-ROM Drive Access Floppy Disk Drive Access PC Card Slot Identifier NumLk Scr Lk Hard Drive or Zip Drive Access PC Card Access CapsLock Figure 2-3 Status Indicator Panel Battery Indicators The two sets of battery indicators show whether or not the primary Lithium ion battery and/or the optional second Lithium ion battery are installed,and indicate the condition of each. (Figure 2-3.) Battery 1 is the Lithium ion bat tery which is installed in Multi-function Bay 1 and Battery 2 is the Lithium ion battery which is installed in Multi-function Bay 2. The battery indicators are displayed only for a battery which is installed. 20 LifeBo ok 700 Series from Fuji tsu Using Your LifeBook 700 Series A small arrow icon (Battery Charging indicator) appears to the left of each of the Battery Level indicators and above the number (Battery identifier) if that battery is charging . The Battery Charging indicator flashes if the battery is too hot or too cold to charge. (Figure 2-3.) The Battery Charging indicators operate whether the power switch is Off or On. The symbols inside the battery outline of the Battery Level indicator show the operating level available in that battery. (Figure 2-4.) If there is no battery charging and the power switch is Off then the AC Adapter indicator and the Battery indicators will all be off. CAUTION A shorted battery is damaged and must be replaced. (See Figure 2-4.) CAUTION Turning off the power with the power switch or using the Suspend/Resume button when any of the Access indicators are On may cause loss of data and/or system errors. 76%­100% 51%­75% 26%­50% 13%­25% CAUTION Batteries subjected to shocks, vibration temperatures or extreme temperatures can be permanently damaged. CD-ROM Drive Access Indicator The CD-ROM Access indicator tells you the CD-ROM drive is being accessed. The CD-ROM Access indicator will flash when the software tries to access a CD or CD-ROM even if no CD-ROM drive is installed. Low Warning 12% Dead Battery Shorted Battery Figure 2-4 Battery Level Indicator 21 Section Two POINT The Windows 95 CD automatic insertion function will periodically check for a CD installed in the drive, causing the CD-ROM Access indicator to flash. The CD automatic insertion function allows your system to automatically start a CD as soon as it is inserted in the drive and the tray is closed. It will begin playing an audio CD or will start an application if the CD has an auto run file on it. To disable the CD automatic insertion function do as follows: 1. Save all data and close all applications. 2. Click on the Start button. 3. Point to Settings. 4. Click on the Control Panel. The control panel window will be displayed. 5. Double click on the System icon. The system properties dialogue box will be displayed. 6. Click on the Device Manager tab. The device list will be displayed. 7. Click on the + to the left o f the CD-ROM icon. The CD-ROM drive manufacturer's name and model will be displayed. 8. Click on the CD-ROM drive manufacturer's name and model. 9. Click on Properties. The CD-ROM drive manufacturer's name and model properties dialogue box will be displayed. 10. Click on the Settings tab. 11. Click on the automatic insertion notification box to toggle it off. 12. Click on OK. 13. Click on OK in the system properties dialogue box. 14. Restart your notebook according to the message displayed. You can re-enable the function by repeating the process except in step 11 change the setting to on. Hard Drive or Zip Drive Access Indicator The Hard Drive Access indicator tells you when either the internal hard drive,the optional second hard drive, or the optional Zip drive is being accessed. POINT The Hard Drive Access indicator does not show which hard drive, or Zip drive is being accessed. It works the same for any one. POINT If you do not wish to have the CD automatic insertion function on you can disable it. 22 LifeBo ok 700 Series from Fuji tsu Using Your LifeBook 700 Series Floppy Disk Drive Access Indicator The Floppy Disk Drive Access indicator tells you a floppy disk drive is being accessed. The Floppy Disk Drive Access indicator will flash when your software tries to access a floppy disk even if no floppy disk drive is installed. PC Card Access Indicators The PC Card Access indicators tell you when an installed PC Card is being accessed. Card 1 is the bottom connector inside the slot and Card 2 is the upper connector inside the card slot. Type III cards are always Card 1 only. The PC Card Access indicator will flash if your software tries to access a PC Card even if none are installed. NumLk Indicator The NumLk indicator tells you the internal keyboard is set in ten-key numeric keypad mode. (See page 33 for more information on the numeric keypad.) You can activate the NumLk mode by pressing the NumLk/Scr Lk key while holding down the Shift key. Deactivate the mode the same way that you activated it. CapsLock Indicator The CapsLock indicator tells you when the keyboard is set for all capital letters. Activate the all capital letters setting by pressing the CapsLock key on the keyboard. Deactivate the setting the same way that you activated it. Scr Lk Indicator The Scr Lk indicator tells you when scroll lock is active. You can activate or deactivate the scroll lock by pressing the NumLk/Scr Lk key. Deactivate the mode the same way that you activated it. On Off Figure 2-5 Power Switch POWER ON Facing the keyboard and display panel ,m ove the power switch towards the rear of your notebook. This is the On position. (See Figure 2-5.) When you are done working you can leave your notebook in Suspend mode, (see pages 44 and 95), or you can turn it off. The power switch moved toward the front of your notebook is in the Off position. (See the section Power Off, pages 24-25, for the recommended shutoff procedures.) 23 Section Two CAUTION After turning off your notebook, make sure that it has been Off at least 10 seconds before turning the power switch to On. If you do not you could cause a system error. When you turn on your notebook be sure you have a power source. This means that at least one battery is installed and charged, or that the AC adapter or the auto/airline adapter is connected and has power. CAUTION The main Lithium ion battery is not charged when you purchase your notebook. Initially you will need to connect the AC adapter to use it. If you purchase an optional second Lithium ion battery, it will not be charged when you get it, you will need to charge it prior to use. When the power switch is turned on, your notebook carries out a Power On Self Test (POST) to check the internal parts and configuration. If a fault is found a beep will sound and/or an error message will be displayed. (See Troubleshooting on pages 138-140) Depending on the nature of the problem you may be able to continue by starting the operating system or by entering the setup utility and revising the settings. After satisfactory completion of the Power On Self Test (POST) your notebook will load your operating system. (See Boot Menu on pages 105106 to see which kind of disk will be the source.) CAUTION Never turn off your notebook during Power On Self Test (POST) or it will cause an error message to be displayed when you turn your notebook on the next time. (See the Troubleshooting information on pages 138-140.) POWER OFF Before turning off the power by putting the power switch in the Off position, check that the Hard Drive,CD-ROM, PC Card and the Floppy Disk Drive Access indicators are all Off. (See Figure 2-3, page 20.) If you turn off the power while accessing a disk or PC Card there is a risk of loss of data. The Off position is reached by facing the keyboard and display panel,and moving the switch toward the front of your notebook. To assure that your notebook shuts down without error, use the Windows 95 shut down procedure. CAUTION Do not carry your notebook around with the power on or subject it to shocks or vibration, as you risk damaging your notebook. 24 LifeBo ok 700 Series from Fuji tsu Using Your LifeBook 700 Series CAUTION Never turn your notebook off while an application is running. Be sure to close all files, exit all applications and shut down your operating system prior to turning off the power with the power switch. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors. Shutting down your notebook from Windows 95 lets your notebook shut down operations, and turn off the power in the proper sequence to prevent errors. The sequence is: 1.Go to the Start button menu. 2. Click on ShutDown. 3. Verify that Shut down the computer? is selected and click on Yes . If you are going to store your notebook for a month or more,take the following precautions: 1. Remove any CD and/or floppy disk. 2. After shutting down with Windows 95 turn off your notebook using the power switch. 3. Close your notebook display panel. 4. Disconnect the AC adapter. 5. Remove the batteries and store them separately in a cool dry place. POINT When your notebook has been shut down from Windows 95, it is not the same as being turned off from the power switch. It is in a pseudo-off state, with all applications closed, but can and must be turned on by pressing the Suspend/ Resume button. It is drawing some current in the pseudo-off state. RESTARTING THE SYSTEM When you wish to restart your system be sure that you follow the proper procedure. The procedure is as follows: 1.Go to the Start button menu. 2. Click on ShutDown. 3. Click on Restart the computer? 4. Verify that Restart the computer? is selected and click on Yes. Windows 95 will shutdown and restart your notebook. POINT You may also select Shut down the computer and once the power is off for 10 seconds or more you can restart your notebook with the Suspend/Resume button, or once the power is off, turn the power switch to Off for 10 seconds and then switch it to On. These alternative methods are not recommended. 25 Section Two POINT In Windows 95 pressing the Ctrl+Alt+Del keys simultaneously triggers the ShutDown submenu of the Start menu. catalog with the information for ordering accessories for your notebook. Double left-click on the icon and then on the appropriate button for the information selection you wish. s BATTERIES The Lithium ion batteries are rechargeable with an operating time of up to three (3) hours depending on active power management features and user activity levels. Your notebook can be operated on the primary Lithium ion battery alone or in a dual battery configuration with an optional second Lithium ion battery. A built-in bridge battery allows a charged Lithium ion battery to be exchanged for a discharged one by "warm-swapping". To warm-swap, have a charged battery ready, put your notebook in Suspend mode, remove the low battery and quickly insert a charged battery. The Lithium ion battery operating time may become shorter than the reference value if it is used under the following conditions: s When used at temperatures that exceed a low of 5°C or a high of 35°C. High temperatures not only reduce charging efficiency, but can also cause battery deterioration. (The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range.) The battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one. When using a high cur rent device such as a modem, a LAN card,the CD-ROM drive, or the hard drive frequently. CAUTION Turning off the power switch without exiting Windows 95 may cause an error when you start the next time. Turning the power to On when it has been Off for less than 10 seconds may also cause an error when you start the next time. s FUJITSU WELCOME CENTER The Fujitsu Welcome Center is an icon on your Windows 95 desktop. Clicking on it gives you access to product registration forms and instructions, change of address information and forms, contact information including telephone numbers and e-mail addresses, and an accessory Using the AC adapter will conserve your battery when using a high current device such as a modem, a LAN card,the CD-ROM drive, or the hard drive frequently. 26 LifeBo ok 700 Series from Fuji tsu Using Your LifeBook 700 Series CAUTION Actual battery life will vary based on screen brightness, applications, features, power management settings, battery condition, and other customer preferences. CD-ROM drive or hard usage may also have a significant impact on battery life. CAUTION Under federal, state or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at 1-800-8FUJITSU (1-800-838-5487). Bridge Battery The bridge battery is a NiCd battery that is built-in your notebook and is constantly being recharged.A bridge battery allows a charged Lithium ion battery to be exchanged for a discharged one by "warm-swapping". To warm-swap have a charged battery ready, put your notebook in Suspend mode, remove the low battery and quickly insert a charged battery. The bridge battery capacity is not large, about 3 minutes,and can vary with the condition of your notebook. CAUTION Data may be lost and/or system errors introduced if the warm swap is not performed quickly or a power adapter installed. CAUTION Do not leave a faulty battery in your notebook. It might damage your AC adapter, optional auto/airline adapter, another battery, or your notebook itself. It may also prevent operation of your notebook by draining all available current into the bad battery. CAUTION The bridge battery can not support an operating notebook. The notebook must be in Suspend mode. Shorted Batteries If your Status Indicator panel shows a shorted battery, check the installation for that battery by removing and re-installing it. If it still shows that it is shorted, replace it with a new battery. 27 Section Two s CAUTION A shorted battery is damaged and must be replaced so that it does not damage anything else. Recharging the Batteries If you want to check the condition of either the primary Lithium ion battery or an optional second Lithium ion battery, check the Battery Level indicators located on the Status Indicator panel. These indicators change as the battery levels change. Battery 1 is a Lithium ion battery which is installed in Multi-function Bay 1 and Battery 2 is a Lithium ion battery which is installed in Multi-function Bay 2. (Figure 2-3 on page 20.) You can also check the PowerPanel toolbar. The Lithium ion batteries are recharged internally using the AC adapter or auto/airline adapter. To recharge the batteries: Make sure the battery to be charged is installed in either Multi-function bay of your notebook and connect the AC or auto/airline adapter. Make sure that the Battery Charging indicator to the left of the Battery Level indicator of the battery to be charged is visible on the Status Indicator panel. Make sure the percentage charge is shown inside the Battery Level icon. (Figure 2-4 on page 21.) s s When two Lithium ion batteries are installed, the charge/discharge rate of the primary and optional second Lithium ion batteries are the same,as they are connected in parallel and are both charging and/or discharging at the same time. Since the rates are the same, one may finish charging or discharging before the other if they were not at the same charge le vel when they were installed and/or the AC or auto/ airline adapter was connected. There is no memory effect on the Lithium ion batteries, which means that you do not need to discharge them completely before recharging. A single fully discharged Lithium ion battery will charge in approximately three (3) hours when your notebook is Off or in Suspend mode. The charging time from fully discharged for two Lithium ion batteries together, is approximately 5 hours when your notebook is Off or in Suspend mode.Of course partially charged batteries will not take as long to charge. The charge times will be significantly longer if your notebook is in use while the batteries are charging (from approximately nine (9) hours for one battery to approximately 15 hours for two batteries with normal operating levels). CAUTION Using heavy current devices such as LAN cards or frequent CD-ROM accesses may prevent charging completely. 28 LifeBo ok 700 Series from Fuji tsu Using Your LifeBook 700 Series Low Battery State When the battery is running low, your notebook beeps about every 15 seconds and the Battery Level indicator(s) flash. If you do not respond to the low battery alarm,the batteries will continue to discharge until they are too low to operate. When this happens there will be a multiple beep alarm,the Battery Level indicator will show dead battery, and your notebook will go into Suspend mode to try and protect your data as long as possible. Your power management settings do not affect what happens at the dead battery alarm level. Your notebook will go to Suspend mode. (Figure 2-3 on page 20.) CAUTION You may not be able to hear the audio alarms if the volume control is set too low or is turned off by either hardware or software but you will still be able to see the Battery Level indicator(s) flash. When the low battery alarm occurs you need to save all your active data and put your notebook into Suspend mode until you can provide a new power source. You should provide this power as soon as possible. The new power source can be a charged battery or a power adapter, either AC or auto/airline. CAUTION When you are in Suspend mode there must always be at least one power source active. If you turn off the power with the power switch, or remove all power sources, battery, AC adapter or auto/ airline adapter, while your notebook is in Suspend mode any data which has not been saved to the hard drive will be lost. Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an AC adapter, an optional auto/ airline adapter, or a charged battery. Dead Battery Suspend mode shows on the Status indicator just like the normal Suspend mode. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Suspend mode, your data can be maintained for sometime. If a power source is not provided promptly, the Power indicator will stop flashing and go out,and you will have lost the data that was not stored. Once you provide power you can continue to use your notebook while an adapter is charging the battery, but the battery trickle charges under these conditions. If you want to charge the battery more quickly, put your notebook into Suspend mode, or turn off your notebook while the adapter is charging the battery. (See Power Offon pages 24-25 for shutdown procedures.) CAUTION There is no guarantee that data will not be lost once your notebook enters the Dead Battery Suspend mode. 29 Section Two INTEGRATED ERGOTRAC POINTING DEVICE Cursor Cursor Control Left Button Right Button Figure 2-6 ErgoTrac Pointing Device The ErgoTrac pointing device is composed of a short, comfortable, dish-shaped pointing device and two buttons located in front of the keyboard. The ErgoTrac pointing device has the function of a mouse,and moves the cursor around on the screen ­ up, down, left and right. A light pressure with the tip of your finger is all that is required to operate the ErgoTrac. The more pressure you use the faster the cursor will move. The second part of the ErgoTrac pointing device ­ the buttons ­ function as mouse buttons,and the functions they perform depend on the application you are running. Figure 2-6 shows the position of the ErgoTrac pointing device and buttons. POINT An external mouse can be connected to the PS/2 port on the right side of the notebook, and used simultaneously with the ErgoTrac pointing device. 30 LifeBo ok 700 Series from Fuji tsu Using