User manual FUJITSU LIFEBOOK S2210 - Document

Fujitsu LifeBook S Series BIOS Guide LifeBook S Series Model: S2210 - Vista Document Date: 01/30/2007 Document Part Number: FPC58-1655-01 F U J I T S U C O M P U T E R S Y S T E M S C O R P O R AT I O N 1 LifeBook S Series Notebook S Series BIOS BIOS SETUP UTILITY The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there should be no need to set or change the BIOS environment to operate your notebook. The BIOS Setup Utility configures: Navigating through the Setup Utility The BIOS setup utility consists of six menus: Main, Advanced, Security, Boot, Info and Exit. This document explains each menu in turn including all submenus and setup items. The following procedures allow you to navigate the setup utility menus: 1. To select a menu, use the cursor keys: [ ], [ ]. Device control feature parameters, such as changing I/O addresses and boot devices. System Data Security feature parameters, such as passwords. 2. To select a field within a menu or a submenu, use the cursor keys: [ ], [ ]. Entering the BIOS Setup Utility To enter the BIOS Setup Utility, do the following (or use the TrustedCore Menu, as detailed in the next section): 1. Turn on or restart your notebook. 2. Press [F2] once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed. 3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings. 3. To select the different values for each field, press the [Spacebar] to change to the next higher selection and [F5] or [-] to go to the next lower selection. 4. To activate a submenu press the [Enter] key. 5. To return to a menu from a submenu, press the [Esc] key. 6. To go to the Exit menu from any other menu, press the [Esc] key. Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen. Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed. Pressing the Enter key again will select the highlighted choice. Using the TrustedCore Menu When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. The TrustedCore Menu provides shortcuts to the following menus and information screens: BIOS Setup Diagnostic Screen Boot Menu Patent Information System Information Continue Booting 7. Pressing the [F9] key resets all items in the BIOS to the default values. 8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be asked to verify this selection before it is executed. 9. Pressing the [F1] key gives you a general help screen. Clicking on any of the fields will invoke the screen, information, or action described. The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen. Entering the Setup Utility After a Configuration Change or System Failure If there has been a change in the system configuration that does not agree with the parameter settings stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an error message after the Power On Self Test (POST). If the failure is not too 2 Main Menu severe, it will give you the opportunity to modify the settings of the setup utility, as described in the following steps: 1. When you turn on or restart the computer there is a beep and/or the following message appears on the screen: Error message - please run SETUP program Press key to continue, to run SETUP 2. If an error message is displayed on the screen, and you want to continue with the boot process and start the operating system anyway, press the [F1] key. If your notebook emits a series of beeps that sounds like a code and the display is blank, please refer to the Troubleshooting section of your system Use's Guide. The Troubleshooting Section includes a list of error messages and their meanings. If your data security settings require it, you may be asked for a password before the operating system will be opened. 3. If an error message is displayed on the screen, and you want to enter the setup utility, press the [F2] key. 4. When the setup utility starts with a fault present, the system displays the following message: Warning! Error message [Continue] 5. Press any key to enter the setup utility. The system will then display the Main Menu with current parameters values. 3 LifeBook S Series Notebook MAIN MENU ­ SETTING STANDARD SYSTEM PARAMETERS The Main Menu allows you to set or view the current system parameters. (See Navigating through the Setup Utility on page 2 for more information) The following tables show the names of the menu fields for the Main menu and its submenus, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Note that the actual drive labels shown may vary. PhoenixBIOS Setup Utility Security Boot Info System Time and System Date can also be set from your operating system without using the setup utility. Use the Date and Time icon on your Windows Control panel or type time or date from the MS-DOS prompt. Main Advanced Exit Item Specific Help System Time: System Date: [02:34:56] [01/29/2007] [FUJITSU MHV2100BH PL] [None] [English (US)] Adjust calendar clock. , , or selects field. Drive0 Drive1 Language: F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 1. Main Menu Table 1: Fields, Options and Defaults for the Main Menu Menu Field System Time: Options ­-- Default ­-- Description Sets and displays the current time. Time is in a 24 hour format of hours:minutes:seconds with 2 digits for each. (HH:MM:SS). Example: 16:45:57. You may change each segment of the time separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys. 4 Main Menu Table 1: Fields, Options and Defaults for the Main Menu Menu Field System Date: Options ­-- Default ­-- Description Sets and displays the current date. Date is in a month/day/ year numeric format with 2 digits each for month and day and 4 digits for year. (MM/DD/YYYY) for example: 03/20/ 2006. You may change each segment of the date separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys. Display the type of device on this ATA/IDE interface. Pressing the Enter key selects the Drive0 submenu allowing additional device configuration options for this interface. Display the type of device on this ATA/IDE interface, if there is one. Pressing the Enter key selects the Drive1 submenu allowing additional device configuration options for this interface. The default setting differs between the US/European and the Japanese model. Selects the display language for the BIOS. Drive0 Selects the Drive0 Serial ATA drive submenu Selects the Drive1 Serial ATA drive submenu The product number of the hard drive. The product number of the CD-ROM drive. [English (US)] Drive1: Language: · English (US) · Japanese (JP) 5 LifeBook S Series Notebook Drive0 Submenu of the Main Menu The Drive0 submenu identifies what ATA devices are installed. Note that actual hard drive label shown may vary. Depending on the drive type, information such as cylinders, heads and sectors may also be displayed. PhoenixBIOS Setup Utility Main Drive0 [FUJITSU MHV2080BH] Item Specific Help Type: Total Sectors: Maximum Capacity: [Auto] LBA Format 195371568 100GB SATA1 Select Serial ATA/IDE drive installed here. [Auto] The BIOS auto-types the drive on boot time. [None] The drive is disabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 2. Drive0 Submenu Table 2: Fields, Options and Defaults for the Drive0 Submenu of the Main Menu Menu Field Type: Options · Auto · None Default [Auto] Description Selects the hard drive device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Setup items do not appear. Logical Block Addressing (LBA) LBA Format Total Sectors: Maximum Capacity: ----- ----- The total number of sectors on your hard disk The maximum capacity of your hard disk A bootable CD-ROM or DVD-ROM may have a floppy disk or hard drive format. When a bootable CD-ROM or DVD-ROM is used, drive allocations change automatically without changing the BIOS setup. If a floppy disk format CD-ROM or DVD-ROM is used, the disc becomes Drive A. The CD-ROM or DVD-ROM will only take drive C: (hard drive format) if the internal hard drive is not present or is disabled. The bootable CD-ROM or DVD-ROM can never use a C: designation if a formatted internal hard drive is present since the C: designator is always reserved for the internal hard drive.The boot sequence ignores the new drive designations, however, your application software will use the new designations. Be aware of the operating environment when booting from CD-ROM/DVD-ROM or you may mistakenly overwrite files. 6 Main Menu Drive1 Submenu of the Main Menu The Drive1 submenu allows you to configure secondary ATA devices. Note that actual hard drive label shown may vary. Depending on the drive type, information such as cylinders, heads and sectors may also be displayed. PhoenixBIOS Setup Utility Main Primary Master [None] Item Specific Help Type: Multi-Sector Transfers: LBA Mode Control: Transfer Mode: Ultra DMA Mode: [Auto] [Disabled] [Disabled] [Standard] [Disabled] Select Serial ATA/IDE drive installed here. [Auto] The BIOS auto-types the drive on boot time. [None] The drive is disabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 3. Drive1 Submenu F9 Setup Defaults F10 Save and Exit Table 3: Fields, Options and Defaults for the Drive1 Submenu of the Main Menu Menu Field Type: Options · Auto · None Default [Auto] Description NOTE: The Type field does not appear as a drop-down menu. Tap the spacebar to toggle the selections. Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following setup items do not appear. Multi-Sector Transfers: · · · · · Disabled 2 Sectors 4 Sectors 8 Sectors 16 Sectors [Disabled] The best option is selected by the BIOS automatically when Auto is selected and cannot be selected by the user. Specifies the number of sectors per block for multiple sector transfer. LBA Mode Control: · Disabled · Enabled [Disabled] The best option is selected by the BIOS automatically when Auto is selected and cannot be selected by the user. Enables or disables Logical Block Addressing in place of Cylinder, Head, Sector addressing. 7 LifeBook S Series Notebook Table 3: Fields, Options and Defaults for the Drive1 Submenu of the Main Menu Menu Field Transfer Mode: Options · · · · · · · · · · · · · · Standard Fast PIO 1 Fast PIO 2 Fast PIO 3 Fast PIO 4 Multiword DMA 1 Multiword DMA 2 Disabled Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Default [Standard] Description The best option is selected by the BIOS automatically when Auto is selected and cannot be selected by the user. Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. Ultra DMA Mode: [Disabled] The best option is selected by the BIOS automatically when Auto is selected and cannot be selected by the user. Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. Exiting from Main Menu When you have finished setting the parameters on this menu, you can either exit from the setup utility, or move to another menu. If you wish to exit from the setup utility, press the [Esc] key or use the cursor keys to go to the Exit menu or to move to another menu. 8 Advanced Menu ADVANCED MENU ­ SETTING DEVICE FEATURE CONTROLS The Advanced Menu allows you to: Set the I/O addresses for the infrared ports. Set the features of the keyboard/mouse. Select between the display panel and/or an external display or video projector. Set internal device configurations Configure USB features. Configure miscellaneous features such as Wake Up On LAN. Configure DMI Event Logging. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See Navigating through the Setup Utility on page 2 for more information) The following tables show the names of the menu fields for the Advanced Menu and its submenus, all of the options for each field, the default settings and a description of the field's function, and any special information needed to help understand the field's use. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help F1 Help ESC Exit Table 4: Fields, Options and Defaults for the Advanced Menu Menu Field Serial/Parallel Port Configurations Keyboard/Mouse Features Video Features Serial/Parallel Port Configurations Keyboard/Mouse Features Video Features Internal Device Configurations CPU Features USB Features Miscellaneous Configurations Event Logging Configures serial ports and parallel ports. Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 4. Advanced Menu F9 Setup Defaults F10 Save and Exit Description When selected, opens the Serial/Parallel Port Configurations submenu which allows the user to modify settings for serial, infrared, and parallel ports. When selected, opens the Keyboard/Mouse Features submenu, which allows setting external and internal keyboard and mouse parameters. When selected, opens the Video Features submenu, which allows setting of the display parameters, including routing of video signals to different displays or video projectors. 9 LifeBook S Series Notebook Table 4: Fields, Options and Defaults for the Advanced Menu Menu Field Internal Device Configurations CPU Features Description When selected, opens the Internal Device Configuration submenu, which allows enabling or disabling the IDE LAN, and modem controllers. When selected, opens the CPU Features submenu, which allows the user to enable or disable the AMD Virtualization(TM) features. USB Features Miscellaneous Configurations Event Logging Configures USB features. Configures miscellaneous features, such as Wake Up On LAN and Power Button. When selected, opens the event logging submenu. 10 Advanced Menu Serial/Parallel Port Configuration Submenu of the Advanced Menu The Serial/Parallel Port Configuration submenu provides the ability to set the I/O addresses and interrupt levels for the infrared ports of your system. To prevent IRQ and address conflicts, avoid changing the default settings. If you must change the settings, you can call 1-800-8Fujitsu for technical assistance. All I/O addresses in Table 5 are in hexadecimal. I/O addresses, DMA channels, and Interrupt levels can be entered in various ways, including via the BIOS setup utility, the control software for the I/O device, or the hardware. If any two ports or devices have the same I/O address assigned your system will not function normally. Please keep a record of original settings before making any changes in the event that a restoration is required. See your hardware and software documentation as well as the setup utility to determine settings, limitations, etc. PhoenixBIOS Setup Utility Advanced IrDA Port Configurations Serial Port: Base I/O Address/IRQ Infrared Port: Mode: Base I/O Address/IRQ: DMA Channel: Parallel Port: Mode: Base I/O Address: Interrupt: [Enabled] [3F8/IRQ 4] [Enabled] [FIR] [2E8/IRQ 3] [DMA 3] [Enabled] [Bi-directional] [378] [IRQ 7] Item Specific Help [Disabled] The port is disabled. [Enabled] The port is enabled with user configuration. [Auto] Plug & Play OS configure the port. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 5. Serial/Parallel Port Configuration Submenu 11 LifeBook S Series Notebook Table 5: Fields, Options and Defaults for Serial/Parallel Port Configurations Submenu of Advanced Menu Menu Field Serial Port: Options Default [Enabled] Description Configures the serial port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). Allows user to set the serial port base I/O address and interrupt when serial port is Enabled. Disabled Enabled Auto 3F8/IRQ 4 2F8/IRQ 3 3E8/IRQ 4 2E8/IRQ 3 Disabled Enabled Auto IrDA FIR 3F8/IRQ 4 2F8/IRQ 3 3E8/IRQ 4 2E8/IRQ 3 DMA 1 DMA 3 Disabled Enabled Auto Output Only Bi-directional ECP Base I/O Address/IRQ: [3F8/IRQ 4] Infrared Port: [Enabled] Configures the infrared port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). When the infrared port is enabled this option is available allowing the user to set the mode for the infrared port. Standard IrDA (IrDA 1.0) transmits data at up to 115.2 Kbps; FIR (IrDA 1.1) transmits at up to 4Mbps. Allows user to set the infrared port I/O address and interrupt when the infrared port is Enabled. Mode: [FIR] Base I/O Address/IRQ: [2E8/IRQ 3] DMA Channel: Parallel Port: [DMA 3] [Enabled] Allows user to set the direct memory access channel when FIR is Enabled. Configures the parallel port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). When the parallel port is enabled this option is available allowing the user to set the mode for the parallel port. Bi-directional allows two-way transfer of information between your notebook and a parallel device. Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP Mode allows communication with the ECP class of parallel I/O devices. Allows user to set the parallel port base I/O address when the parallel port is Enabled. Mode: [Bi-directional] Base I/O Address: 378 278 3BC IRQ 5 IRQ 7 [378] Interrupt: [IRQ 7] Allows user to set the parallel port interrupt when the parallel port is Enabled. 12 Advanced Menu Keyboard/Mouse Features Submenu of the Advanced Menu The Keyboard/Mouse Features submenu is for setting the parameters of NumLock. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Advanced Keyboard/Mouse Features Numlock: [Auto] Hot Plug: [Enabled] Internal Pointing Device: [Auto Disabled] Initialization on Resume: [Fast] [On] or [Off] Numlock is On or Off. [On/Padlock Off] Numlock is On, but use with [Fn] for 10-key input. [Auto] Numlock is set to On/ Padlock Off when PS/2 keyboard is connected, otherwise Off. * Windows XP preserves Numlock state when the user logs off. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 6. Keyboard/Mouse Features Submenu Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu Menu Field Numlock: Options · · · · Auto On Off On/Padlock Off Default [Off] Description Sets the NumLock function state when the computer completes booting. When [On] or [Off], Numlock is on or off. When [On/Padlock Off] is pressed, Numlock is on, but [Fn] key must be pressed used for 10-key input. When [Auto] is selected, Numlock is set to On/Padlock Off when a PS/2 keyboard is connected, otherwise it is off. Windows preserves Numlock state when the user logs off. Enables or disables the hot-pluggability of the external device. Hot Plug: · Disabled · Enabled · · · · Auto Disabled Manual Setting Always Enabled Always Disabled [Enabled] Internal Pointing Device: [Auto Disabled] When [Auto Disabled] is selected, the internal pointing device is disabled when an external PS/2 device is connected. When [Manual Setting] is selected, the internal pointing device can be enabled or disabled with a hot key. When [Always Enabled] is selected, the internal device is always enabled; when [Always Disabled] is selected, the device is always disabled. When [Fast] is selected, the initialization of external PS/2 devices is optimized to speed up upon resume. (If PS/2 devices do not function after resume, select [Normal]). When [Normal] is selected, PS/2 device initialization is not optimized. Initialization On Resume: · Fast · Normal [Fast] 13 LifeBook S Series Notebook Video Features Submenu of the Advanced Menu The Video Features Submenu is for setting the display parameters. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Video Features Display: Compensation: [Auto] [Enabled] Select display terminal. * This setting is not effective after operating system starts up. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 7. Video Features Submenu Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Display: Options · · · · Internal Flat Panel External (Analog) External (Digital) Auto Default [Auto] Description Selects where the video signal will be routed. Note that once the system boots up, the settings for the Windows video driver take precedence over this setting. Compensation: · Disabled · Enabled [Enabled] Enables or disables display compensation. Display compensation is used to match the native resolution of the display with the input. For example, if you are using an application whose resolution causes it to appear smaller than the screen, enabling Compensation will expand the image to fill the screen. 14 Advanced Menu Internal Device Configurations Submenu of the Advanced Menu The Internal Device Configuration submenu allows the user to configure other internal devices. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help [Disabled] Serial ATA port is disabled. [Enabled] Serial ATA port is enabled. Main Advanced Internal Device Configurations Serial ATA Controller: IDE Contoller: Bluetooth(R): LAN Controller: Wireless LAN: IEEE1394 Controller: [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 8. Internal Device Configuration Submenu Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu Menu Field Serial ATA Controller: Options · Disabled · Enabled · Disabled · Enabled · Disabled · Enabled · Disabled · Enabled · Disabled · Enabled · Disabled · Enabled Default [Enabled] Description Enables or disables serial ATA devices. IDE Controller: [Enabled] Allows you to enable and/or disable any or all IDE devices. Bluetooth(R): [Enabled] Enables or disables the optional Bluetooth device. LAN Controller: [Enabled] Enables or disables the LAN controller. Wireless LAN: [Enabled] Enables or disables the optional wireless LAN device. IEEE1394 Contrroller: [Enabled] Enables or disables the IEEE 1394 device. 15 LifeBook S Series Notebook CPU Features Submenu of the Advanced Menu The CPU Features Submenu allows the user to enable or disable the AMD Virtualization(TM) feature. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Select AMD Virtualization(TM) enabled or disabled. Main Advanced CPU Features AMD Virtualization(TM): [Disabled] F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 9. CPU Features Submenu Table 9: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu Menu Field Options · Enabled · Disabled Default Description AMD Virtualization(TM) [Disabled] Enables or disables the AMD Virtualization(TM) feature. 16 Advanced Menu USB Features Submenu of the Advanced Menu The USB Features Submenu configures the USB features for your system. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced USB Features Legacy USB Support: SCSI SubClass Support: [Enabled] [Enabled] [Disabled] The feature is disabled. [Enabled] Legacy Floppy Emulation is enabled and USB floppy is available without USB aware OS. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 10. USB Features Submenu Table 10: Fields, Options and Defaults for the USB Features Submenu of the Advanced Menu Menu Field Legacy USB Support: Options · Disabled · Enabled Default [Enabled] Description When Disabled is selected, legacy USB emulation is disabled. When Enabled is selected, legacy USB emulation is enabled and USB devices are available without USB-aware OS. When Enabled is selected, USB devices that belong to the SCSI subclass in the mass storage class (e.g., USB Memory Key) are enabled. SCSI SubClass Support: · Disabled · Enabled [Enabled] 17 LifeBook S Series Notebook Miscellaneous Configurations Submenu of the Advanced Menu The Miscellaneous Configurations Submenu configures miscellaneous features for your system. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced Miscellaneous Configurations Power Button: Wake up on LAN: Force LAN Boot: Volume Setting: UMA Video Memory Size: [Disabled] [Disabled] [Disabled] [Middle] [128MB] Configures the power button. *ACPI OS ignores this setting. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 11. Miscellaneous Configurations Submenu Table 11: Fields, Options and Defaults for the Miscellaneous Configurations Submenu Menu Field Power Button: Options · Disabled · Power Off · Disabled · Enabled · Disabled · Enabled Default [DIsabled] Description When Disabled is selected, the power button does not respond to a press. When Power Off is selected, the button turns the power off. When Enabled is selected, system will wake up when internal LAN device receives a Magic Packet while the system is powered off. This feature is active only when "Wake up on LAN" is enabled. When enabled, in the event of a system wake-up on LAN, the system will try to first boot from the LAN before attempting to boot from any other device, regardless of the BIOS boot priority settings or disabling of the Preboot Execution Environment. Selects the initial volume setting for the system. Wake up on LAN: Force LAN Boot: [Disabled] [Disabled] Volume Setting: · · · · · · · · Off Minimum Middle Maximum 32MB 64MB 128MB 224MB [Middle] UMA Video Memory Size: [128MB] Allows you to select the maximum shared video memory size. Video memory is dynamically allocated as needed for running applications by Dynamic Video Memory Technology (DVMT). 18 Advanced Menu Event Logging Submenu of the Advanced Menu The Event Logging Submenu configures event logging features for DMI events. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced Event Logging Event Log Capacity: Event Log Validity: View Event Log: Event Logging: System Boot Event: Clear All Event Logs: Mark Events as Read: Space Available Valid [Enter] [Enabled] [Disabled] [No] [Enter] Press key to view the contents of the event log. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 12. Event Logging Submenu Table 12: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu Menu Field Event Log Capacity: Options Default Space Available Valid · Enter · Disabled · Enabled · Disabled · Enabled · No · Yes · Enter Description Display only. Event Log Validity: View Event Log: Event Logging: Display only. Allows you to view content of event log. Turns event logging on and off for all DMI events. [Enter] [Enabled] System Boot Event: Clear All Event Logs: [Disabled] Turns event logging on and off for DMI system boot events. [No] When set to [Yes] all event logs will be cleared at next boot. Mark Events as Read: [Enter] Allows you to make all events currently in the event log as read. 19 LifeBook S Series Notebook SECURITY MENU ­ SETTING THE SECURITY FEATURES The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See Navigating through the Setup Utility on page 2 for more information) Entering a password incorrectly three times in a row will cause the keyboard and mouse to be locked out and the warning [System Disabled] to be displayed. If this happens, restart the computer by turning off and on the power with the power switch and use the correct password on reboot. Note: Unless you have previously enabled the power switch in the BIOS, it will not be possible to turn off the unit with the switch. This is applicable for non-ACPI OS's. If you set a password, write it down and keep it in a safe place. If you forget the password you will have to contact your support representative to regain access to your secured functions and data. If you make an error when re-entering the password a [Warning] will be displayed on the screen. To try again press the [Enter] key and then retype the password. Press the [Esc] key to abort the password setting process. If the Password on Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or Save-to-Disk modes. The following tables show the names of the menu fields for the Security menu and its submenus, the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. The default condition is no passwords required and no write protection. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Minimum User Password Length: Password on Boot: On Automatic Wake up: KB Lock on Resume: Boot from Removable Media: Flash Write: Hard Disk Security Owner Information Security Chip Setting Clear Clear [Enter] [Enter] [0] [Disabled] [Disabled] [Disabled] [All] [Enabled] Press key to set Supervisor Password to enable any password features. Then password entry is required to enter BIOS Setup. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 13. Security Menu F9 Setup Defaults F10 Save and Exit 20 Security Menu Table 13: Fields, Options and Defaults for the Security Menu Menu Field Supervisor Password is: User Password is: Options ­-- Default Clear Description A display-only field. Set is displayed when the system Supervisor Password is set and Clear when it is not. A display-only field. Set is displayed when the general User Password is set, and Clear when it is not. Sets, changes or cancels Supervisor Password. The Supervisor Password may be up to eight characters long and include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor Password is set it must be used to access the BIOS setup utility. This field can only be accessed if the Supervisor Password is set. Sets, changes or cancels the User Password. The User Password may be up to eight characters long and must include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a User Password is set it must be used to access the BIOS setup utility. Sets the minimum length for User Password. ­-- Clear Set Supervisor Password [Enter] [Enter]