User manual FUNAI F42PDME

SIMPLE SET UP GUIDE GUÍA DE INSTALACIÓN RÁPIDA GUIDE D'INSTALLATION RAPIDE Some cables here are not included with the plasma display. In order to view television, it is necessary to connect a tuner device (example: cable box, satellite box, DTV, etc.) to the plasma display. Algunos de los cables no se suministran con la pantalla de plasma. Con el fin de ver televisión, es necesario conectar un dispositivo sintonizador (por ejemplo: un decodificador de televisión por cable, un decodificador de televisión por satélite, DTV, etc.) a la pantalla de plasma. Certains des câbles présentés ici ne sont pas fournis avec l'écran plasma. Un tuner doit être raccordé au moniteur pour pouvoir regarder la télévision (par exemple : décodeur câble ou satellite, télévision numérique, etc.) Plasma Display rear side Parte posterior de la pantalla de plasma Arrière de l'écran plasma 1CAMCORDER CÁMARA GRABADORA CAMÉSCOPE 4DVD AC IN AUDIO AUDIO OUT L R VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 R L VIDEO S-VIDEO REPRODUCTOR DE DVD LECTEUR DVD AUDIO L VIDEO S-VIDEO COMPONENT1 COMPONENT2 R L Y Pb Pr R L Y Cb Cr R AC IN AUDIO AUDIO OUT L R R L VIDEO S-VIDEO COMPONENT1 COMPONENT2 R L VIDEO S-VIDEO R R AUDIO L Y Cb Cr VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 L Y Pb Pr Power cord is included. El cable de alimentación viene incluido. Le cordon d'alimentation est fourni. OR CABLE/SAT 2AMPLI 3 FIER/RECEIVER O OU TV POR CABLE/SATÉLITE CÂBLE/SAT OR O OU 5SET TOP BOX FOR DTV AJUSTE DECODIFICADOR SUPERIOR PARA DTV DÉCODEUR DE TV NUMÉRIQUE AMPLIFICADOR/RECEPTOR AMPLIFICATEUR/RÉCEPTEUR VCR VIDEOGRABADOR MAGNÉTOSCOPE OR O OU DVD REPRODUCTOR DE DVD LECTEUR DVD 1 CAMCORDER CÁMARA GRABADORA CAMÉSCOPE Plasma Display Pantalla de Plasma Ecran Plasma AUDIO AUDIO OUT L R VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 R L VIDEO S-VIDEO R L VIDEO S-VIDEO R L VIDEO S­VIDEO OR O OU 2 AMPLIFIER/RECEIVER AMPLIFICADOR/RECEPTOR AMPLIFICATEUR/RÉCEPTEUR Plasma Display Pantalla de Plasma Ecran Plasma AUDIO AU D I O I N VI D EO TV AU X L AUDIO OUT L R R R VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 L VIDEO S-VIDEO R L VIDEO S-VIDEO 3 VCR VIDEOGRABADOR MAGNÉTOSCOPE CABLE/SAT TV POR CABLE/SATÉLITE CÂBLE/SAT OR O OU OR O OU Plasma Display Pantalla de Plasma Ecran Plasma AUDIO AUDIO OUT L AU D I O VI D EO L VI D EO S­VI D EO R VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 L VIDEO S-VIDEO R OR O OU R R L VIDEO1 S-VIDEO1 DVD REPRODUCTOR DE DVD LECTEUR DVD OR O OU 4 DVD REPRODUCTOR DE DVD LECTEUR DVD Plasma Display Pantalla de Plasma Ecran Plasma AUDIO R AUDI O R L Y C O M PO N EN T VI D EO Cb Cr L Y Cb Cr COMPONENT1 COMPONENT2 R L Y Pb Pr 5 SET TOP BOX FOR DTV AJUSTE DECODIFICADOR SUPERIOR PARA DTV DÉCODEUR DE TV NUMÉRIQUE Plasma Display Pantalla de Plasma Ecran Plasma AUDIO R L Y Cb Cr COMPONENT1 Pr AUDI O R L Y C O M PO N EN T Pb COMPONENT2 R L Y Pb Pr FOR MORE INFORMATION PARA MÁS INFORMACIÓN POUR PLUS D'INFORMATIONS 1. Owner's Manual Manual del usuario / Manuel de l'utilisateur 2. http://www.funai.us 3. 1-800-605-8453 Printed in Malaysia 1EMN20190 L0605UF PLASMA DISPLAY Owner's Manual F42PDME Before you can view a picture on the plasma display, you must first connect the unit to an external video source. See page 18 of the owner's manual. IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING AFTER READING OWNER'S MANUAL, PLEASE CALL TOLL FREE 1-800-605-8453, OR VISIT OUR WEB SITE AT http://www.funai.us WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. S3125A RADIO-TV INTERFERENCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. The serial number of this product may be found on the back of this unit. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Date of Purchase Dealer Dealer Address Dealer Phone No. Model No. Serial No. 2 Thank you for purchasing this plasma display. Please make sure to read this manual before using the plasma display and pay particular attention to the Safety Instructions enclosed within. When you have finished reading this manual, store it in a safe place for easy access in the future. When moving the plasma display Due to the weight of this plasma display, two people should be used when moving it. Both people should make sure to grasp the top of the display with one hand and the base of the display with the other hand, as in the following illustration. Regarding This Manual · Product and company names appearing within this manual are trademarks or registered trademarks of their respective owners. · Although special care has been taken to ensure that all information contained within this manual is correct at time of writing, the information is subject to change without notice. · Make sure to read the manual carefully and follow all instructions contained within. We will not be held responsible for any damages caused by improper use or handling of this product. · Reproducing this manual by any means, in whole or in part, is prohibited. Optional Accessories To mount the plasma display on a wall, the following accessory is available: VISIONMOUNTTM Flat Panel TV Wall Mount from SANUS SYSTEMS, for large flat panel televisions (32" to 60"). Refer to page 21 for mounting the plasma display. NOTE: The wall mounts are not supplied with the plasma display. # CAUTION · This PDP F42PDME is for use only with the Sanus Systems Model VMPL. Wall Mount. Use with other wall mounts is capable of resulting in instability, causing possible injury. · When mounting the plasma display with the Sanus Systems wall mount, make sure to mount it on the wood studs inside the wall, as failure to do so may result in instability, causing possible injury. · Refer to the instruction manual included with the wall mount for details when securing the plasma display to the wall. 3 English CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 INSERTING THE REMOTE CONTROL BATTERIES . . . . . . . . . . . . . . . . . . . . . .5 REMOTE CONTROL RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 COMPONENT NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 OPERATING THE PLASMA DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 BASIC OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 SELECTING THE INPUT SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 CHANGING THE ASPECT RATIO (SCREEN MODE) . . . . . . . . . . . . . . . . . . . . . . . . .10 STILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 SLEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 NAVIGATING THE SET UP MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Layout of the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ENTERING THE MAIN MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 PICTURE SELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Automatically Adjusting the Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Manually Adjusting the Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Initializing the Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 WINDOW SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 SWITCHING THE DISPLAY LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 SETTING THE SCREEN SAVER AND THE BACKGROUND COLOR . . . . . . . . . . . . .16 Setting the Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Setting the Background Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 EXTERNAL INPUT TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 CONNECTING DEVICES TO THE AV INPUT TERMINALS . . . . . . . . . . . . . . . . . . . .18 VIDEO Signal Connection (Basic Signal Transfer) . . . . . . . . . . . . . . . . . . . . . . . . .18 S-VIDEO Signal Connection (Better Signal Transfer) . . . . . . . . . . . . . . . . . . . . . . .18 CONNECTING DEVICES TO THE COMPONENT INPUT TERMINALS . . . . . . . . . . .19 Component 1 Signal (Y, Cb, Cr) Connection (Best Signal Transfer) . . . . . . . . . . . .19 Component 2 Signal (Y, Pb, Pr) Connection (Best Signal Transfer) . . . . . . . . . . . .19 CONNECTING PLASMA DISPLAY TO AUDIO SYSTEM . . . . . . . . . . . . . . . . . . . . . .20 AUDIO Signal Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 CONNECTING THE POWER CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ATTACHING A WALL MOUNT BRACKET (SOLD SEPARATELY) . . . . . . . . . .21 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 CLEANING THE PLASMA DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 FUNAI CORPORATION LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . .26 4 SUPPLIED ACCESSORIES POWER VOL MUTE SCREEN MODE STILL INPUT SELECT DISPLAY MENU PREVIOUS SLEEP P Owner's Manual (1EMN20189) P Remote Control (NE802UD) P AA batteries x 2 P Set Up Guide (1EMN20190) P Power cable (WBC0202H0001) NOTE: If any of these accessories are missing, please contact your dealer. INSERTING THE REMOTE CONTROL BATTERIES 1 Remove the back cover of the remote control while pressing the tab on the back cover down with your finger. 3 Replace the back cover of the remote control. 2 Insert two AA size batteries, making sure that the polarities of the batteries match the symbols inside the remote control. NOTE: · Do not insert a mix of old and new batteries. · Do not insert a mix of different brands of batteries or different types of batteries. · Always use new, fresh batteries as replacement. · Never attempt to charge, heat, burn or take apart batteries. REMOTE CONTROL RANGE Operate the remote control within a 30 degree angle on both sides of the infrared sensor on the main unit. You can operate the remote control from a distance of several yards away from the main unit. NOTE: Other devices which use infrared beams, sunlight, fluorescent lights, etc., may affect the range and effectiveness of the remote control. Make sure the plasma display is positioned in a place which minimizes interference from them. Approximately 5.5 yds (5 m) With in 30 degrees Approximately 7.6 yds (7 m) With in 30 degrees Approximately 5.5 yds (5 m) 5 English This product comes with the following accessories: Please confirm that they are included. COMPONENT NAMES MAIN UNIT Front 3 Rear POWER AC IN AUDIO AUDIO OUT L R R L VIDEO S-VIDEO COMPONENT1 COMPONENT2 R L VIDEO S-VIDEO AUDIO R L Y Cb Cr VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 VOLUME INPUT SELECT R L Y Pb Pr 3 POWER 1 VOLUME INPUT SELECT VOLUME INPUT SELECT 2 AC IN AUDIO OUT L R VIDEO1 S-VIDEO1 VIDEO2 S-VIDEO2 R Input Terminals AUDIO R L VIDEO S-VIDEO COMPONENT1 COMPONENT2 L VIDEO S-VIDEO AUDIO R L Y Cb Cr Infrared Sensor R L Y Pb Pr 4 5 6 7 8 9 1 2 3 4 5 6 7 6 POWER button: Turns the power ON or in STANDBY. POWER indicator: Lights up (Blue) when the power is in the standby mode. Lights up (Green) when the power is ON. STANDBY indicator: Lights up when the power is in the standby mode. Disappears when the power is ON. INPUT SELECT button: Selects input terminals. VOLUME K(up) / L(down) button: Increases or decreases the volume. AC IN terminal: Connect the supplied power cable for a standard AC outlet. AUDIO OUT: Output terminals for audio. 8 9 AUDIO/VIDEO/S-VIDEO: Input terminals for an audio and video signal. You can select either VIDEO or S-VIDEO. COMPONENT: Input terminals for a component signal. You can make a Y-Cb-Cr interlaced connection to component 1 or Y-Pb-Pr progressive or interlaced connection to component 2. 1 POWER VOL 2 3 4 5 MUTE SCREEN MODE STILL INPUT SELECT 6 7 MENU DISPLAY 9 PREVIOUS SLEEP 10 11 8 1 2 3 4 5 6 7 8 POWER button: Turns the main power ON or in STANDBY. VOL K(up) / L(down) button: Increases or decreases the volume. MUTE button: Turns the audio off or on. SCREEN MODE button: Selects aspect ratios available for the screen. STILL button: Pauses the image shown on the screen. INPUT SELECT button: Selects input terminals. DISPLAY button: Displays the name of the selected input terminal on the screen. SLEEP button: Sets the sleep timer. 9 MENU button: Accesses the setup menu, allowing you to access various settings. 10 PREVIOUS button: Moves up one level in the setup menu. 11 K(up) / L(down) button: Selects the various modes in the setup menu. {(left) / B(right) button: Selects and adjusts levels for the various settings. B(enter) button: Also used as the enter button. 7 English REMOTE CONTROL OPERATING THE PLASMA DISPLAY BASIC OPERATIONS POWER VOL 3 POWER MUTE SCREEN MODE Adjust the volume and screen size according to your requirements. Perform adjustments to the volume (VOL K / L button), screen aspect ratio (SCREEN MODE button) and picture settings (MENU button). NOTE: · When you adjust the volume with the VOL K / L button, a message such as the following is displayed on the screen. This message disappears approximately 4 seconds after performing adjustments. STILL INPUT SELECT INPUT SELECT DISPLAY The following is a simple explanation of the procedure for turning the power of the display ON or in STANDBY and the procedure for selecting the input signal. The procedure described here is for the remote control, however the POWER, INPUT SELECT and VOLUME buttons on the plasma display can also be used in the same way. · If you turn the audio mute on, a message slowly flashes on the screen. At this time, if you press another button, this flashing stops. 1 Press the POWER button. Confirm that the STANDBY indicator is lit before pressing the POWER button. The power turns ON and the POWER indicator on the main unit turns green. The STANDBY indicator on the main unit disappears. NOTE: · It takes approximately 8 seconds for the screen to display after turning the power ON, but this is not a malfunction. · To turn the audio mute off, either press the MUTE button again or press the VOL K / L button. · If you press either the PREVIOUS, K, L, B or { button in a mode apart from the image adjustment mode. A message such as the following is displayed. 4 Press the POWER button to turn the power STANDBY. The POWER indicator on the main unit turns blue and the STANDBY indicator lights up. 2 Select the input signal by pressing the INPUT SELECT button. Each time you switch the input, the name of the selected input terminal is displayed on the screen for approximately 4 seconds. NOTE: · "No signal" is displayed on the screen if there is no input from the selected terminal and there is no message currently displayed on the screen for volume adjustment or the setup menu, etc. · If there is no video signal and there has been no operation from the remote control or the buttons on the main unit for more than 15 minutes, the auto shut-off function activates and the display switches to standby mode. NOTE: · You cannot turn the power ON for approximately 3 seconds after the power enters the standby mode. Do not turn the power to STANDBY and then ON again in a short time interval. · Even if the power is turned to STANDBY, the main unit is in the standby mode. In order to shut the main power of the display OFF, it is necessary to remove the AC cord from the power outlet. 8 Selecting the Input Signal POWER VOL MUTE SCREEN MODE 1 Press the INPUT SELECT button to select the input signal. Each time you switch the input signal, the name of the selected input terminal is displayed on the display for approximately 4 seconds. The INPUT SELECT button cycles through the input terminals in the following pattern: Video 1 (S-Video 1) Video 2 (S-Video 2) Component 2 Component 1 STILL INPUT SELECT INPUT SELECT DISPLAY DISPLAY The procedure for selecting the input signal described here is for use with the remote control. However, the INPUT SELECT button on the plasma display can also be used in the same way. Displaying the Current Input Signal NOTE: · When switching the input signal, audio mute turns ON temporarily. · S-VIDEO1 takes priority over the VIDEO 1 jack, as does S-VIDEO 2 over the VIDEO 2 jack. Therefore, if there is input to the VIDEO and SVIDEO terminals at the same time, the S-VIDEO signal is displayed on the screen. If the S-VIDEO cable is not connected to the plasma display, the VIDEO signal will be displayed on the screen. · 480i (interlaced) signals can be connected to the COMPONENT 1 and 2 terminals. Any of the following display formats: 480i, 480p (progressive), 1080i and 720p (progressive) signals can be connected to the COMPONENT 2 terminal. If one of these video signals is detected, the format of the input signal is displayed after the name of the current input terminal, as in the following manner. 1 Press the DISPLAY button. The name of the current input terminal is displayed on the screen. 2 To clear the name of the current input terminal, press the DISPLAY button again or wait for approximately 4 seconds. NOTE: · To redisplay the name of the input terminal, press the DISPLAY button again. · A "No signal" message appears if there is no video signal and there is no message currently displayed on the screen for volume adjustment or the setup menu, etc. If there continues to be no video signal for more than 10 seconds, "No signal" slowly moves around the screen. · If there is no video signal and there has been no operation from the remote control or the buttons on the main unit for more than 15 minutes, the auto shut-off function activates and the display switches to standby mode. 9 English SELECTING THE INPUT SIGNAL OPERATING THE PLASMA DISPLAY CHANGING THE ASPECT RATIO (SCREEN MODE) POWER VOL MUTE SCREEN MODE SCREEN MODE STILL Each time you change the screen mode, the name of the selected mode is displayed on the screen for approximately 4 seconds. The SCREEN MODE button switches between the screen modes in the following pattern. Normal Full Wide Zoom INPUT SELECT DISPLAY NOTE: · When switching the input signal, the audio mute turns ON temporarily. · You can only select the "Normal" and "Zoom" screen modes for 1080i and 720p video signals connected to the COMPONENT 2 terminal. By changing the aspect ratio of the screen you can select the manner in which you wish to view the picture. 1 2 Press the SCREEN MODE button to display the current screen mode. Press the SCREEN MODE button a second time to change the screen mode. Mode Normal Picture Explanation Normal will display a 4:3 picture at its standard 4:3 size. For 1080i and 720p video signals, a picture will be displayed at 16:9 size. Normal Full Full Full will display a 4:3 picture at a 16:9 size, with horizontal elongation necessary to fill the screen. Wide Wide Wide will display a 4:3 picture at a 16:9 size, with less horizontal elongation necessary to fill the screen because a little bit of the top and bottom will be cut off. Zoom Zoom Zoom will magnify the entire 4:3 picture to fill the screen, with no horizontal elongation to fill the screen, as more of the top and bottom are cut off. Use this mode to view letterboxed 4:3 picture content to get a widescreen picture. A 16:9 picture will be magnified similarly, but to a lesser extent. 10 INPUT SELECT POWER VOL DISPLAY MUTE SCREEN MODE MENU PREVIOUS STILL STILL INPUT SELECT SLEEP SLEEP DISPLAY To freeze the image on the screen. Selecting sleep timer. 1 Press the STILL button. The still mode turns on and the image displayed on the screen is frozen. 1 Press the SLEEP button. The sleep timer is displayed on the screen. NOTE: NOTE: · When the still mode is on, the message "Still" slowly flashes on the screen. · When the still mode is on, the audio is muted. · You cannot turn the still mode on when there is no video signal or when switching between video signals. · If the sleep timer is activated, the remaining time is displayed on the screen. If not activated, "0 minutes" is displayed. 2 Press the SLEEP button to set the time. The SLEEP button switches between the times. 0 minutes 10 minutes 90 minutes 2 Press the STILL button again to turn the still mode off. NOTE: · You can also press the INPUT SELECT, DISPLAY, SLEEP, VOL K(up) / L(down), MUTE, SCREEN MODE or MENU buttons to turn the still mode off. The timer starts counting down after the message displaying the set time disappears (after approximately 4 seconds). NOTE: · The remaining time displayed for the sleep timer changes in steps of 1 minute. · To change the set time, repeat the above procedure. 11 English STILL SLEEP OPERATING THE PLASMA DISPLAY NAVIGATING THE SET UP MENU In the setup menu, you can specify settings for picture adjustment, picture position, language, screen saver and background. NOTE: · If you do not press any buttons for approximately 20 seconds, the display automatically exits the menu mode. · We recommend to set to the initialized setting of "Manual" in the picture mode. Layout of the Setup Menu The various functions in the setup menu are outlined below: MAIN MENU Picture select Picture mode Dynamic Manual News Brightness Contrast Color Tint Sharpness Cool Color temp. Reset Normal Warm Movie Window setting H-Position V-Position Français Language English Español Detail Screen saver Back ground Fast Off Slow Opaque Translucent 12 INPUT SELECT INPUT SELECT DISPLAY DISPLAY K MENU PREVIOUS MENU PREVIOUS MENU SLEEP MENU SLEEP PREVIOUS B L 1 Press the MENU button. The display enters the main menu and the MAIN MENU is displayed on the screen. 1 Enter the main menu with the MENU button. "Picture select" is selected on the MAIN MENU. 2 Press the B button to select. The PICTURE SELECT menu is displayed on the screen. NOTE: · If you press the PREVIOUS button or the MENU button on the MAIN MENU, the menu is cancelled. · To select a setting, use the B button. NOTE: · Press the PREVIOUS button to return to the MAIN MENU. Pressing the MENU button cancels the menu. · Picture select display will disappear from the TV screen automatically after about 20 seconds if you do not press any buttons. 13 English ENTERING THE MAIN MENU PICTURE SELECT OPERATING THE PLASMA DISPLAY INPUT SELECT Manually Adjusting the Picture Settings DISPLAY K MENU PREVIOUS 1 PREVIOUS B SLEEP Select "Picture mode" on the PICTURE SELECT screen with the K / L buttons. Select "Manual" with the { / B buttons. The display enters the manual mode and you can specify individual adjustments. MENU { L 2 3 Automatically Adjusting the Picture Settings Select the mode to adjust with the K / L buttons. The modes rotate in the following order: "Picture mode" - "Brightness" - "Contrast" - .. ...- "Reset" - "Picture mode" 1 2 Select "Picture mode" on the PICTURE SELECT screen with the K / L buttons. Select the automatic adjustment mode according to the type of picture displayed on the screen with the { / B buttons. 4 Adjust the selected mode using the { / B buttons. NOTE: · If you have selected Brightness, Contrast, Color, Tint or Sharpness, the menu display disappears, and a bar for adjusting the selected mode appears in the center of the bottom of the screen. · You can select "Color temp." from among three modes: "Normal", "Warm" and "Cool". · If you select "Reset" and press the B button, the adjusted values return to their initial settings. 5 6 To adjust a different mode, repeat steps 3 and 4. Press the PREVIOUS button to return to the Picture mode. NOTE: · Pressing the MENU button cancels the menu. NOTE: · There are 3 modes for automatically adjusting the picture settings; "News", "Movie" and "Dynamic". Initializing the Adjustments 3 Press the PREVIOUS button to return to the MAIN MENU. NOTE: · Pressing the MENU button cancels the menu. 1 2 Select "Reset" on the PICTURE SELECT screen with the K / L buttons. Press the B button. The settings you specified individually are initialized. NOTE: · The initialized setting of "Manual" are as follows: BRIGHTNESS: 50/100 CONTRAST: 70/100 COLOR: 50/100 TINT: 50/100 SHARPNESS: 1/2 COLOR TEMP.: Normal 14 INPUT SELECT