_________________________________________________________________________________________________English BT-03i user's manual 1 _________________________________________________________________________________________________English Index Overview Getting started How to answer the phone call Specification 2 _________________________________________________________________________________________________English Safety Information Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution: Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3 _________________________________________________________________________________________________English 1. Overview A B E F D C 1-1 Function keys: A B C D E F Silicon ear hook Power key Volume control (Slide control) Answer phone key Microphone USB connector (charging) 1-2 Package contents: Wireless headset 110~240V AC adaptor 50cm USB cable Quick guide CD manual 1-3 Charging: USB charge: 1. Plug your USB cable (Mini B side) into your wireless headset. 2. Plug your USB cable (A side) into your PC/NB. 4 _________________________________________________________________________________________________English 3. The Power key LED will be red when it is charging. Power key will be red continually 4. When the light turns off, the headset is ready for use. Adapter Charge: 1. Plug your USB cable (Mini B side) into your wireless headset. 2. Plug the USB (A side) into the adapter, then the plug the adapter into a power outlet. 3. The Power key LED will be red when it is charging. 4. When the light turns off, the headset is ready for use. 1-4 LED light defined: Event Power On Power On after 5 sec. Enter Pairing Connection Mode Adjust Volume Adjust Volume after 5 sec. Answer Call Hang Up Call USB Charger Connected Battery Charge OK * Continuously LED Status Red LED ON, Volume Blue LED ON, Hook Blue LED ON Red LED OFF, Volume Blue LED OFF, Hook Blue LED OFF Red LED blinks fast for 0.05 seconds, then is OFF for 0.05 seconds* Red LED blinks slow for 0.05 seconds, then is OFF for 5 seconds* Volume Blue LED ON Volume Blue LED OFF Hook Blue LED ON Hook Blue LED OFF Red LED ON Red LED OFF 1-5 Buttons defined: Button Press Press Long Press Very Long Press Seconds 3 5 8 5 _________________________________________________________________________________________________English Button 1 function Mode Power OFF Press --- Power On ; Connect to Last Paired Audio gateway and A2DP Media Long Press --- Enter Pairing Very Long Press --- Reset Paired Device Phone Mode Press --- Power Off Long Press --- Power Off Very Long Press --- Power Off Power Button 2 function Phone Mode Event Incoming Call Active Call Hook Short touch --- Answer Call Short touch --- Hang Up Call Volume Slide function Event Volume Control Volume Up Volume Down 2. Getting started 2-1 Power on: After you complete the charging, press the power key for three seconds to turn on the headset. After you turn on the wireless headset, the power LED will be lit RED, the volume and answer key will be lit BLUE. 2-2 Power off: Press the power key for three seconds in any mode and the wireless headset will power off. 2-3 Pairing: When the headset is off, press the power key for five seconds until the RED light blinks quickly, then the headset is under pairing mode. You can connect with other Bluetooth devices now. - Connect with mobile phone Turn on your mobile phone Bluetooth function, then search for the Bluetooth device, and the mobile phone will show "BT-03i" on the screen. When connected, input "0000" to complete the connection. You can listen to music from your mobile phone and receive phone calls as well. (Make sure the mobile phone supports A2DP and mp3 music play) - Connect with PC/NB Open PC/NB Bluetooth application software and start the search for the wireless headset. Once it finds the wireless headset, it will show "BT-03i". 6 _________________________________________________________________________________________________English When connected, input"0000" to complete the pairing. After you get a connection, connect to A2DP protocol, and you can open the media player to listen to music. 3. How to answer the phone call When connected with a mobile phone, the connection protocol will be "headset" profile. When you receive an incoming call, you can touch " " answer key, then you can receive the phone call. When you answer the call, the answer key " " will be lit blue until you finish the phone call. When you want to finish the phone call, just touch the answer key again, and you can hang up the phone call and the blue light will turn off. When you receive a phone call, the music will pause automatically, once you hang up the call, the music will start playing again. (Make sure the mobile phone supports Bluetooth function) Button 2 function Phone Mode Event Incoming Call Active Call Hook Short touch --- Answer Call Short touch --- Hang Up Call 4. Specifications Bluetooth spec Main chip Profile Range Battery Working voltage Charging time Working time Driver unit Sensitivity Frequency response Impedance Control interface Dimension Bluetooth2.0+EDR CSR BC-05 A2DP, headset, hands free 33 feet 320mA rechargeable Hi-polymer Li-on battery <30mA 3 hours Up to 15 hours 30mm full range driver 145dB +/- 3dB 18Hz~22KHz 32 ohm Touch panel 146 x 143 x 57mm 7 ...