FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this Eric Lu equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) Responsible Party Name: G.B.T. INC. Address: 18305 Valley Blvd., Suite#A LA Puent, CA 91744 Phone/Fax No: (818) 854- 9338/ (818) 854-9339 hereby declare s that the product Product Name: Mother Board Model Number: GA 6OMM7 Conforms to the following specifications: FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a), Class B Digital Device Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful and (2) this device must accept any inference received, including that may cause undesired operation. ERIC LU Representative Person's Name: Signature: Date: May. 22, 2000 -Reorient or relocate the receiving antenna -Move the equipment away from the receiver -Plug the equipment into an outlet on a circuit different from that to which the receiver is connected -Consult the dealer or an experienced radio/television technician for additional suggestions You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void Your authority to operate such equipment. This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity We, Manufacturer/Importer (full address) G.B.T. Technology Träding GMbH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-6OMM7 is in conformity with (reference to the specification under which conformity is declared) in accordance with 89/336 EEC-EMC Directive EN 55011 Limits and methods of measurement of radio disturbance characteristics of industrial, scientific and medical (ISM high frequency equipment EN55013 Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and associated equipment Limits and methods of measurement of radio disturbance characteristics of household electrical appliances, portable tools and similar electrical apparatus Limits and methods of measurement of radio disturbance characteristics of fluorescent lamps and luminaries Immunity from radio interference of broadcast receivers and associated equipment Limits and methods of measurement of radio disturbance characteristics of information technology equipment EN 61000-3-2* EN60555-2 Disturbances in supply systems caused by household appliances and similar electrical equipment "Harmonics" EN61000-3-3* EN60555-3 Disturbances in supply systems caused by household appliances and similar electrical equipment "Voltage fluctuations" EN 55014 EN 50081-1 Generic emission standard Part 1: Residual, commercial and light industry Generic immunity standard Part 1: Residual, commercial and light industry Generic emission standard Part 2: Industrial environment EN 50082-1 EN 55015 EN 55081-2 EN 55020 EN 55082-2 Generic immunity standard Part 2: Industrial environment EN 55022 ENV 55104 Immunity requirements for household appliances tools and similar apparatus DIN VDE 0855 Cabled distribution systems; Equipment part 10 for receiving and/or distribution from part 12 sound and television signals EN 50091- 2 EMC requirements for uninterruptible power systems (UPS) CE marking (EC conformity marking) The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 73/23 EEC EN 60065 Safety requirements for mains operated electronic and related apparatus for household and similar general use Safety of household and similar electrical appliances EN 60950 Safety for information technology equipment including electrical business equipment EN 60335 EN 50091-1 General and Safety requirements for uninterruptible power systems (UPS) Manufacturer/Importer Signature (Stamp) : Rex Lin Rex Lin Date: May. 22, 2000 Name : 6OMM7 Socket 370 Processor Motherboard USER'S MANUAL Socket 370 Processor Motherboard REV. 1.1 First Edition R-11-01-000511 How This Manual Is Organized This manual is divided into the following sections: 1) Revision History 2) Item Checklist 3) Features 4) Hardware Setup 5) Performance & Block Diagram 6) Suspend to RAM 7) BIOS Setup 8) Appendix Manual revision information Product item list Product information & specification Instructions on setting up the motherboard Product performance & block diagram Instructions STR installation Instructions on setting up the BIOS software General reference Table Of Content Revision History Item Checklist Summary of Features 6OMM7 Motherboard Layout Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition Performance List Block Diagram Suspend to RAM Installation Memory Installation Page Index for BIOS Setup Appendix P.1 P.2 P.3 P.5 P.6 P.29 P.30 P.31 P.37 P.38 P.71 6OMM7 Motherboard Revision History Revision 1.1 Revision Note Initial release of the 6OMM7 motherboard user's manual. Date May.2000 The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. May. 11, 2000 Taipei, Taiwan, R.O.C 1 Item Checklist Item Checklist þThe 6OMM7 motherboard þCable for IDE / floppy device þDiskettes or CD (IUCD) for motherboard driver & utility oInternal COM B Cable (Optional) oInternal USB Cable (Optional) oCable for SCSI device þ6OMM7 user's manual 2 6OMM7 Motherboard Summary Of Features Form Factor CPU Y Y 24.3 cm x 20.5 cm Micro ATX form factor, 4 layers PCB. Socket 370 processor Intel Pentium ® !!! 100/133MHz FSB, Coppermine core FC-PGA Intel CeleronTM 100MHz FSB, Coppermine core PC-PGA Y Chipset Clock Generator Memory Y Y Y Y Y Y Y Y Y Y Y Y Y Y I/O Control Slots On-Board IDE On-Board Peripherals Y Y Y Y Y Hardware Monitor Y Y Y Y Y Y On-Board Sound 2nd cache in CPU (Depend on CPU) Intel 815 HOST / AGP / SDRAM Controller 82801AA I/O Controller Hub(ICH) ICS 9250AF-25 66/100/133 MHz system bus speeds 3 168-pin DIMM sockets Supports PC-100 / PC-133 SDRAM and VCM SDRAM Supports up to 512MB(Max) Supports only 3.3V SDRAM DIMM IT8712 1 AGP Slot Supports 4X mode & AGP 2.0 compliant 3 PCI Slot Supports 33MHz & PCI 2.2 compliant 1 AMR (Audio Modem Riser)Slot 2 IDE bus master (DMA 33/ ATA 66) IDE ports for up to 4 ATAPI devices Supports PIO mode 3, 4 (UDMA33/ATA66) IDE & ATAPI CD-ROM 1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2.88M bytes 1 parallel ports supports SPP/EPP/ECP mode 1 serial ports (COM A) 2 USB ports 1 IrDA connector for IR/CIR (Optional) CPU/Power Supply/System fan revolution detect CPU/Power/System temperature detect System voltage detect CPU overheat shutdown detect AC'97 CODEC Line In / Line Out / Mic In / AUX In / CD In / TEL / Game Port To be continued... 3 Summary of Features PS/2 Connector BIOS Additional Features Y Y Y Y Y Y PS/2 keyboard interface and PS/2 mouse interface Licensed AWARD BIOS, 4M bit Flash ROM Supports Wake-on-LAN (WOL) Supports Internal / External modem wake up Includes 3 fan power connectors Poly fuse for keyboard over-current protection 4 6OMM7 Motherboard 6OMM7 Motherboard Layout PS/2 JP1 USB JP3 JP6 J2 JP4 LED1 JP7 JP25 PGA 370 CPU JP5 COM A J1 Front USB ATX Power VGA LPT 6OMM7 BAT1 FW82815 Game & Audio IDE2 JP27 JP10 JP11 JP26 DIMM1 DIMM2 AGP DIMM3 J10 AC'97 DFP/TV JP12 BZ1 PCI1 J7 PCI2 J6 JP20 FWH JP21 JP24 AMR JP23 JP18 JP22 PCI3 J5 J12 J13 ICH82801 JP13 JP14 JP15 IDE1 J11 J14 5 Floppy 6OMM7 Motherboard Layout $ Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition CPU Speed Setup Connectors Game & Audio Port COM A / VGA / LPT Port USB Connector PS/2 Keyboard & PS/2 Mouse Connector J1 (CPU Fan) J2 (Power Fan) J14 (System Fan) ATX Power JP13 (IR/CIR) Floppy Port IDE 1(Primary)/ IDE 2(Secondary) Port J13 (Ring Power On) J12 (Wake on LAN) J7 (TEL) J6 (AUX_IN) J5 (CD Audio Line In) JP7 (STR LED Connector) & LED 1 (DIMM LED) Front USB Port (Optional) J10 (Extra SMBUS) JP25 (USB Port Selection) [Optional] DFP/TV Out Connector JP27 (SCR) Panel and Jumper Definition J11 (2x11 Pins Jumper) JP18 (Clear CMOS Function) JP4 (STR Enable) JP3 (PS/2 Keyboard Power On) JP22 (Case Open) JP1 (Rear USB Device Wake up Selection) JP20 (FWH Flash Write Protect) JP21 (Top Block Lock) JP5 (Over Voltage CPU Speed Up) JP6 (DIMM Over Voltage) [Optional] JP12 (Internal Buzzer) [Optional] 6 Page P.8 P.9 P.9 P.9 P.10 P.10 P.11 P.11 P.12 P.12 P.13 P.13 P.14 P.14 P.15 P.15 P.16 P.16 P.17 P.17 P.18 P.18 P.19 P.19 P.20 P.20 P.21 P.21 P.22 P.22 P.23 P.23 P.24 P.24 P.25 P.25 6OMM7 Motherboard JP14 (Timeout Reboot Function) P.26 7 6OMM7 Motherboard Layout JP15 (Safe mode/Recovery/Normal) JP23 (PCI/AGP 3VAUX) JP24 (AMR Selection) [Optional] BAT1 (Battery) P.26 P.27 P.27 P.28 8 CPU Speed Setup CPU Speed Setup The system bus frequency can be switched at 66MHz, 100MHz, 133MHz and Auto by adjusting JP10/JP11/JP26 (See Figure 1). The CPU Frequency is control by BIOS. M The CPU speed must match with the frequency RATIO. It will cause system hanging up if the frequency RATIO is higher than that of CPU. JP10/JP11/JP26: CPU Speed Setup 1 JP10 1 1 JP26 JP11 CPU SDRAM JP10 JP11 JP26 Auto Auto 1-2 1-2 1-2 66 100 2-3 2-3 1-2 100 100 2-3 Open 1-2 133 133 Open 2-3 1-2 133 100 Open Open 2-3 Auto Configuration: CPU SDRAM 66 100 100 100 Ö133/100 133 Figure 1 Ö If the CPU FSB is 133 FSB, the frequency of the SDRAM can be determined by SDRAM's SPD or setting in BIOS. M If JP10, JP11, JP25 is not present, FSB will be determined automatically. If these 3 jumpers are available, you can choose at 66MHz, 100MHz, 133MHz and Auto. M Note: Please set the CPU host frequency in accordance with your processor's specifications. We don't recommend you to set the system bus frequency over the CPU's specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals. Whether 9 CPU Speed Setup your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Chipsets, SDRAM, Cards....etc. 10 6OMM7 Motherboard Connectors Game & Audio Port Game Port Line Out MIC In Line In COM A / VGA / LPT Port LPT Port COM A VGA 11 Connectors USB Connector Pin No. 1 2 3 4 5 6 7 8 Definition USB V0 USB D0USB D0+ GND USB V1 USB D1USB D1+ GND 5678 1 23 4 PS/2 Keyboard & PS/2 Mouse Connector PS/2 Mouse 6 4 2 1 5 3 PS/2 Keyboard PS/2 Mouse/ Keyboard Pin No. Definition 1 Data 2 NC 3 GND 4 VCC(+5V) 5 Clock 6 NC 12 6OMM7 Motherboard J1: CPU Fan 1 Pin No. Definition 1 GND 2 +12V 3 SENSE J2: Power Fan 1 Pin No. Definition 1 GND 2 +12V 3 SENSE 13 Connectors J14: System Fan 1 Pin No. Definition 1 GND 2 +12V 3 SENSE ATX Power 10 20 1 11 Pin No. Definition 3,5,7,13,15-17 GND 1,2,11 3.3V 4,6,19,20 VCC 10 +12V 12 -12V 18 -5V 8 Power Good 9 5V SB stand by+5V 14 PS-ON(Soft On/Off) 14 6OMM7 Motherboard JP13: IR/CIR Pin No. Definition 1 VCC 2 NC 3 IRRX 4 GND 5 IRTX 6 NC 7 CIRRX 8 VCC 9 NC 10 NC 1 5 6 10 Floppy Port Red Line 15 Connectors IDE1 (Primary), IDE2 (Secondary) Port IDE 2 IDE 1 Red Line J13: Ring Power On (Internal Modem Card Wake Up) 1 Pin No. 1 2 Definition Signal GND 16 6OMM7 Motherboard J12: Wake On LAN 1 Pin No. Definition 1 +5V SB 2 GND 3 Signal J7: TEL: The connector is for Modem with internal voice connector 1 Pin No. Definition 1 Signal-In 2 GND 3 GND 4 Signal-Out 17 Connectors J6: AUX_IN Pin No. 1 2 3 4 1 Definition AUX-L GND GND AUX-R J5: CD Audio Line In 1 Pin No. Definition 1 CD-L 2 GND 3 GND 4 CD-R 18 6OMM7 Motherboard JP7: STR LED Connector & LED1: DIMM LED + DIMM LED 1 STR LED Connector External Front USB Port (Optional) 1 9 Pin No. 1,4,5,10 2 3,7,9 6 8 2 ...