User manual GIGABYTE GA-P35-DS3

GA-P35-DS3R/ GA-P35-DS3/ GA-P35-S3 LGA775 socket motherboard for Intel® CoreTM processor family/ Intel® Pentium® processor family/Intel® Celeron® processor family User's Manual Rev. 2002 12ME-P35DS3R-2002R Motherboard GA-P35-DS3R/GA-P35-DS3/GA-P35-S3 Motherboard GA-P35-DS3R/GA-P35-DS3/ GA-P35-S3 Jul. 25, 2007 Jul. 25, 2007 Copyright © 2007 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. The logo is exclusively licensed to GIGABYTE UNITED INC. by GIGA-BYTE TECHNOLOGY CO., LTD. GIGABYTE UNITED INC. is designated by GIGA-BYTE TECHNOLOGY CO., LTD as the exclusive global distributor of GIGABYTE branded motherboards. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations: For quick set-up of the product, read the Quick Installation Guide included with the product. For detailed product information, carefully read the User's Manual. For instructions on how to use GIGABYTE's unique features, read or download the information on/from the Support\Motherboard\Technology Guide page on our website. For product-related information, check on our website at: http://www.gigabyte.com.tw Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. Example: Table of Contents Optional Items ................................................................................................................. 6 Box Contents ................................................................................................................. 6 GA-P35-DS3R/DS3/S3 Motherboard Layout ................................................................. 7 Block Diagram ................................................................................................................ 8 Chapter 1 Hardware Installation .................................................................................... 9 1-1 1-2 1-3 Installation Precautions ..................................................................................... 9 Product Specifications .................................................................................... 10 Installing the CPU and CPU Cooler .............................................................. 13 1-3-1 1-3-2 Installing the CPU ................................................................................................ 13 Installing the CPU Cooler ................................................................................... 15 Dual Channel Memory Configuration ................................................................ 16 Installing a Memory ............................................................................................. 17 1-4 Installing the Memory ..................................................................................... 16 1-4-1 1-4-2 1-5 1-6 1-7 1-8 Installing an Expansion Card ......................................................................... 18 Installing the SATA Bracket ............................................................................. 19 Back Panel Connectors ................................................................................. 20 Internal Connectors ........................................................................................ 22 Chapter 2 BIOS Setup ................................................................................................. 35 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 Startup Screen ................................................................................................ 36 The Main Menu .............................................................................................. 37 Standard CMOS Features ............................................................................. 39 Advanced BIOS Features .............................................................................. 41 Integrated Peripherals ..................................................................................... 43 Power Management Setup ............................................................................. 47 PnP/PCI Configurations ................................................................................. 49 PC Health Status ........................................................................................... 50 2-9 MB Intelligent Tweaker(M.I.T.) ....................................................................... 52 2-10 Load Fail-Safe Defaults ................................................................................... 55 2-11 Load Optimized Defaults ................................................................................. 55 2-12 Set Supervisor/User Password ..................................................................... 56 2-13 2-14 Save & Exit Setup ......................................................................................... 57 Exit Without Saving ....................................................................................... 57 -4- Chapter 3 Drivers Installation ...................................................................................... 59 3-1 3-2 3-3 3-4 3-5 Installing Chipset Drivers ............................................................................... 59 Software Applications ..................................................................................... 60 Driver CD Information .................................................................................... 60 Hardware Information ..................................................................................... 61 Contact Us ..................................................................................................... 61 Chapter 4 Unique Features ......................................................................................... 63 4-1 4-2 Xpress Recovery2 ......................................................................................... 63 BIOS Update Utilities ..................................................................................... 68 4-2-1 4-2-2 Updating the BIOS with the Q-Flash Utility ...................................................... 68 Updating the BIOS with the @BIOS Utility ....................................................... 71 4-3 4-4 EasyTune 5 .................................................................................................... 73 Windows Vista ReadyBoost ........................................................................... 74 Chapter 5 Appendix .................................................................................................... 75 5-1 Configuring SATA Hard Drive(s) .................................................................... 75 5-1-1 5-1-2 5-1-3 5-1-4 Configuring Intel ® ICH9R SATA Controllers .................................................. 75 Configuring GIGABYTE SATA2 SATA Controller ............................................. 81 Making a SATA RAID/AHCI Driver Diskette ..................................................... 87 Installing the SATA RAID/AHCI Driver and Operating System ...................... 88 Configuring 2/4/5.1/7.1-Channel Audio ............................................................ 96 Installing the S/PDIF In Cable (Optional) ........................................................... 98 Configuring Microphone Recording ................................................................. 100 Using the Sound Recorder ............................................................................... 102 Frequently Asked Questions ........................................................................... 103 Troubleshooting Procedure .............................................................................. 104 5-2 Configuring Audio Input and Output ................................................................. 96 5-2-1 5-2-2 5-2-3 5-2-4 5-3 Troubleshooting ............................................................................................. 103 5-3-1 5-3-2 Regulatory Statements ............................................................................................... 106 Only for GA-P35-DS3R. -5- Box Contents GA-P35-DS3R, GA-P35-DS3, or GA-P35-S3 motherboard Motherboard driver disk User's Manual Quick Installation Guide Intel® LGA775 CPU Installation Guide One IDE cable and one floppy disk drive cable GA-P35-DS3R: Four SATA 3Gb/s cables GA-P35-DS3/S3: Two SATA 3Gb/s cables GA-P35-DS3R/DS3: One SATA bracket I/O Shield · The box contents above are for reference only and the actual items shall depend on product package you obtain. The box contents are subject to change without notice. · The motherboard image is for reference only. Optional Items 2-port USB 2.0 bracket (Part No. 12CR1-1UB030-51R) 2-port SATA power cable (Part No. 12CF1-2SERPW-01R) S/PDIF in cable (Part No. 12CR1-1SPDIN-01R) COM port cable (Part No. 12CF1-1CM001-32R) LPT port cable (Part No. 12CF1-1LP001-01R) -6- GA-P35-DS3R/DS3/S3 Motherboard Layout KB_MS RCA_SPDIF ATX_12V CPU_FAN LGA775 ATX R_USB1 R_USB2 R_USB3 USB_LAN F_AUDIO GA-P35-DS3R/DS3/S3 AUDIO SYS_FAN1 Intel ® P35 PCIE_3 DDRII1 SYS_FAN2 FDD DDRII2 DDRII3 DDRII4 PCIE_16 RTL8111B PWR_FAN PCIE_1 Intel ® ICH9R Intel ® ICH9 BATTERY PCI1 CLR_CMOS SATAII2 SATAII3 GSATAII0 GIGABYTE SATA2 GSATAII1 SATAII0 SATAII1 SATAII4 SATAII5 SPDIF_O CODEC SPDIF_I PCIE_2 PCI2 IT8718 BIOS IDE1 F_USB2 F_USB1 PCI3 CD_IN COMA LPT CI F_PANEL PWR_LED Only for GA-P35-DS3R. Only for GA-P35-DS3. Only for GA-P35-S3. "*" Only the GA-P35-DS3R/DS3 adopt All-Solid Capacitor design. -7- Block Diagram PCIe CLK (100 MHz) LGA775 Processor CPU CLK+/(400(O.C.)/333/266/200 MHz) Host Interface DDR2 1200(O.C.)/1066/ 800/667 MHz Dual Channel Memory MCH CLK (400(O.C.)/333/266/200 MHz) PCI Express x16 2 SATA 3Gb/s ATA-133/100/66/33 IDE Channel GIGABYTE SATA2 PCI Express Bus 3 PCI Express x1 x1 x1 x1 LAN RJ45 RTL 8111B x1 x1 Intel® P35 BIOS 6 SATA 3Gb/s Intel® ICH9R Intel® ICH9 4 SATA 3Gb/s 12 USB Ports PCIe CLK (100 MHz) PCI Bus Floppy IT8718 CODEC LPT Port COM Port Surround Speaker Out Center/Subwoofer Speaker Out Side Speaker Out MIC Line-Out Line-In 3 PCI PCI CLK (33 MHz) Only for GA-P35-DS3R. Only for GA-P35-DS3. Only for GA-P35-S3. -8- SPDIF In SPDIF Out PS/2 KB/Mouse Chapter 1 1-1 Hardware Installation English Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures: · Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or · · · · warranty sticker provided by your dealer. These stickers are required for warranty validation. Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components. When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely. When handling the motherboard, avoid touching any metal leads or connectors. It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity. Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container. Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off. Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard. Before using the product, please verify that all cables and power connectors of your hardware components are connected. To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components. Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing. Do not place the computer system on an uneven surface. Do not place the computer system in a high-temperature environment. Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user. If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. · · · · · · · · · · -9- Hardware Installation English 1-2 CPU Product Specifications Support for an Intel® Core 2 Extreme processor/ Intel ® Core 2 Quad processor/Intel ® Core 2 Duo processor/ Intel ® Pentium ® processor Extreme Edition/Intel ® Pentium ® D processor/ Intel ® Pentium ® 4 processor Extreme Edition/Intel ® Pentium ® 4 processor/ Intel ® Celeron ® processor in the LGA 775 package (Go to GIGABYTE's website for the latest CPU support list.) Support for Intel ® Hyper-Threading Technology L2 cache varies with CPU 1600(O.C.)/1333/1066/800 MHz FSB North Bridge: Intel ® P35 Express Chipset South Bridge: Intel ® ICH9R / ICH9 4 x 1.8V DDR2 DIMM sockets supporting up to 8 GB of system memory (Note 1) Dual channel memory architecture Support for DDR2 1200(O.C.)/1066/800/667 MHz memory modules (Go to GIGABYTE's website for the latest memory support list.) Realtek ALC889A codec High Definition Audio 2/4/5.1/7.1-channel Support for S/PDIF In/Out Support for CD In RTL 8111B chip (10/100/1000 Mbit) 1 x PCI Express x16 slot 3 x PCI Express x1 slots 3 x PCI slots South Bridge: - 6 x SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII2, SATAII3, SATAII4, SATAII5) supporting up to 6 SATA 3Gb/s devices - 4 x SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII4, SATAII5) supporting up to 4 SATA 3Gb/s devices (Note 2) - Support for SATA RAID 0, RAID 1, RAID 5, and RAID 10 GIGABYTE SATA2 chip: - 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices - 2 x SATA 3Gb/s connectors (GSATAII0, GSATAII1) supporting up to 2 SATA 3Gb/s devices - Support for SATA RAID 0, RAID 1, and JBOD iTE IT8718 chip: - 1 x floppy disk drive connector supporting up to 1 floppy disk drive TM TM TM Front Side Bus Chipset Memory Audio LAN Expansion Slots Storage Interface Only for GA-P35-DS3R. Only for GA-P35-DS3. Only for GA-P35-S3. "*" Only the GA-P35-DS3R/DS3 adopt All-Solid Capacitor design. GA-P35-DS3R/DS3/S3 Motherboard - 10 - English USB Internal Connectors Back Panel Connectors I/O Controller Hardware Monitor Integrated in the South Bridge Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets connected to the internal USB headers) 1 x 24-pin ATX main power connector 1 x 4-pin ATX 12V power connector 1 x floppy disk drive connector 1 x IDE connector 8 x SATA 3Gb/s connectors 6 x SATA 3Gb/s connectors 1 x CPU fan header 2 x system fan headers 1 x power fan header 1 x front panel header 1 x front panel audio header 1 x CD In connector 1 x S/PDIF In header 1 x S/PDIF Out header 2 x USB 2.0/1.1 headers 1 x parallel port header 1 x serial port header 1 x chassis intrusion header 1 x power LED header 1 x PS/2 keyboard port 1 x PS/2 mouse port 1 x coaxial S/PDIF Out connector 1 x optical S/PDIF Out connector 8 x USB 2.0/1.1 ports 1 x RJ-45 port 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone) iTE IT8718 chip System voltage detection CPU/System temperature detection CPU/System/Power fan speed detection CPU overheating warning CPU/System/Power fan fail warning CPU fan speed control (Note 3) Only for GA-P35-DS3R. Only for GA-P35-DS3. Only for GA-P35-S3. - 11 Hardware Installation English BIOS Unique Features Bundled Software Operating System Form Factor 1 x 8 Mbit flash Use of licensed AWARD BIOS PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b Support for @BIOS Support for Download Center Support for Q-Flash Support for EasyTune (Note 4) Support for Xpress Install Support for Xpress Recovery2 Support for Virtual Dual BIOS Norton Internet Security (OEM version) Support for Microsoft® Windows ® Vista/XP/2000 (Note 5) ATX Form Factor; 30.5cm x 21.0cm (Note 1) Due to Windows XP 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. (Note 2) To enable hot plug capability for the SATA connectors (SATAII0, SATAII1, SATAII4, SATAII5) controlled by the ICH9 South Bridge, you must install Windows Vista (on ICH9, hot plug is supported in Windows Vista only) and configure the SATA connectors for AHCI mode. (Refer to Chapter 2, "BIOS Setup," "Integrated Peripherals," for details on enabling AHCI.) (Note 3) Whether the CPU fan speed control function is supported will depend on the CPU cooler you install. (Note 4) Available functions in Easytune may differ by motherboard model. (Note 5) Due to chipset limitation, Intel ICH9R RAID driver does not support Windows 2000 operating system. GA-P35-DS3R/DS3/S3 Motherboard - 12 - 1-3 Installing the CPU and CPU Cooler Read the following guidelines before you begin to install the CPU: · Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.) · Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage. · Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.) · Apply an even and thin layer of thermal grease on the surface of the CPU. · Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur. · Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. Hyper-Threading Technology System Requirements: (Go to Intel's website for more information about the Hyper-Threading Technology) · An Intel ® CPU that supports HT Technology · A chipset that supports HT Technology · An operating system that is optimized for HT Technology · A BIOS that supports HT Technology and has it enabled (Refer to Chapter 2, "BIOS Setup," "Advanced BIOS Features," for instructions on enabling the HT Technology.) English 1-3-1 Installing the CPU A. Locate the alignment keys on the motherboard CPU socket and the notches on the CPU. LGA775 CPU Socket Alignment Key Alignment Key Pin One Corner of the CPU Socket LGA 775 CPU Notch Notch Triangle Pin One Marking on the CPU - 13 - Hardware Installation English B. Follow the steps below to correctly install the CPU into the motherboard CPU socket. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. CPU Socket Lever Step 1: Completely raise the CPU socket lever. Step 2: Remove the protective socket cover. Step 3: Lift the metal load plate on the CPU socket. Step 4: Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pin one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently insert the CPU into position. Step 5: Once the CPU is properly inserted, replace the load plate and push the CPU socket lever back into its locked position. GA-P35-DS3R/DS3/S3 Motherboard - 14 - 1-3-2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the motherboard. (The following procedure uses Intel ® boxed cooler as the example cooler.) Male Push Pin Direction of the Arrow Sign on the Male Push Pin English The Top of Female Push Pin Female Push Pin Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU. Step 2: Before installing the cooler, note the direction of the arrow sign on the male push pin. (Turning the push pin along the direction of arrow is to remove the cooler, on the contrary, is to install.) Step 3: Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Push down on the push pins diagonally. Step 4: You should hear a "click" when pushing down each push pin. Check that the Male and Female push pins are joined closely. (Refer to your CPU cooler installation manual for instructions on installing the cooler.) Step 5: After the installation, check the back of the motherboard. If the push pin is inserted as the picture above, the installation is complete. Step 6: Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard. Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU. - 15 Hardware Installation English 1-4 Installing the Memory Read the following guidelines before you begin to install the memory: · Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest memory support list.) · Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. · Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction. 1-4-1 Dual Channel Memory Configuration This motherboard provides four DDR2 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The four DDR2 memory sockets are divided into two channels and each channel has two memory sockets as following: Channel 0: DDRII1, DDRII2 Channel 1: DDRII3, DDRII4 Dual Channel Memory Configurations Table DDRII1 Two Modules Four Modules DS/SS -DS/SS DDRII2 -DS/SS DS/SS DDRII3 DS/SS -DS/SS DDRII4 -DS/SS DS/SS (SS=Single-Sided, DS=Double-Sided, "- -"=No Memory) DDRII1 DDRII2 Due to chipset limitation, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled if only one DDR2 memory module is installed. 2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used and installed in the same colored DDR2 sockets for optimum performance. When memory modules of different capacity and chips are installed, a message which says memory is operating in Flex Memory Mode will appear during the POST. Intel ® Flex Memory Technology offers greater flexibility to upgrade by allowing different memory sizes to be populated and remain in Dual Channel mode/performance. GA-P35-DS3R/DS3/S3 Motherboard - 16 - DDRII3 DDRII4 1-4-2 Installing a Memory Before installing a memory module , make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR2 DIMMs are not compatible to DDR DIMMs. Be sure to install DDR2 DIMMs on this motherboard. English Notch DDR2 DIMM A DDR2 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly install your memory modules in the memory sockets. Step 1: Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket. Step 2: The clips at both ends of the socket will snap into place when the memory module is securely inserted. - 17 - Hardware Installation English 1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: · Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. · Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage. PCI Express x16 Slot PCI Express x1 Slot PCI Slot Follow the steps below to correctly install your expansion card in the expansion slot. 1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel. 2. Align the card with the slot, and press down on the card until it is fully seated in the slot. 3. Make sure the metal contacts on the card are completely inserted into the slot. 4. Secure the card's metal bracket to the chassis back panel with a screw. 5. After installing all expansion cards, replace the chassis cover(s). 6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your expansion card(s). 7. Install the driver provided with the expansion card in your operating system. Example: Installing and Removing a PCI Express x16 Graphics Card: · Installing a Graphics Card: Gently insert the graphics card into the PCI Express x16 slot. Make sure the graphics card is locked by the latch at the end of the PCI Express x16 slot. · Removing the Card: Press the white latch at the end of the PCI Express x16 slot to release the card and then pull the card straight up from the slot. GA-P35-DS3R/DS3/S3 Motherboard - 18 - 1-6 Installing the SATA Bracket English The SATA bracket allows you to connect external SATA device(s) to your system by expanding the internal SATA port(s) to the chassis back panel. · Turn off your system and the power switch on the power supply before installing or removing the SATA bracket and SATA power cable to prevent damage to hardware. · Insert the SATA signal cable and SATA power cable securely into the corresponding connectors when installing. SATA Bracket SATA Signal Cable SATA Power Cable External SATA Connector The SATA bracket includes one SATA bracket, one SATA signal cable, and one SATA power cable. Power Connector External SATA Connector Follow the steps below to install the SATA bracket: Step 1: Locate one free PCI slot and secure the SATA bracket to the chassis back panel with a screw. Step 2: Connect the SATA cable from the bracket to the SATA port on your motherboard. Step 3: Connect the power cable from the bracket to the power supply. Step 5: Connect the other ends of the SATA signal cable and SATA power cable to your SATA device. For SATA device in external enclosure, you only need to connect the SATA signal cable. Before connecting the SATA signal cable, make sure to turn off the power of the external enclosure. Step 4: Plug one end of the SATA signal cable into the external SATA connector on the bracket. Then attach the SATA power cable to the power connector on the bracket. "*" The SATA bracket is included with the GA-P35-DS3R/DS3 only. - 19 Hardware Installation English 1-7 Back Panel Connectors PS/2 Keyboard and PS/2 Mouse Port Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard. Coaxial S/PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital coaxial audio. Before using this feature, ensure that your audio system provides a coaxial digital audio in connector. Optical S/PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector. USB Port The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as an USB keyboard/mouse, USB printer, USB flash drive and etc. RJ-45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs. Connection/ Speed LED Activity LED Connection/Speed LED: State Description Orange 1 Gpbs data rate Green 100 Mpbs data rate Off 10 Mpbs data rate Activity LED: State Blinking Off Description Data transmission or receiving is occurring No data transmission or receiving is occurring LAN Port · When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard. · When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector. GA-P35-DS3R/DS3/S3 Motherboard - 20 - Center/Subwoofer Speaker Out Jack (Orange) Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration. English Rear Speaker Out Jack (Black) Use this audio jack to connect rear speakers in a 4/5.1/7.1-channel audio configuration. Side Speaker Out Jack (Gray) Use this audio jack to connect side speakers in a 7.1-channel audio configuration. Line In Jack (Blue) The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc. Line Out Jack (Green) The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration. Mic In Jack (Pink) The default Mic in jack. Microphones must be connected to this jack. In addition to the default speakers settings, the ~ audio jacks can be reconfigured to perform different functions via the audio software. Only microphones still MUST be connected to the default Mic in jack ( ). Refer to the instructions on setting up a 2/4/5.1/ 7.1-channel audio configuration in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio." - 21 - Hardware Installation English 1-8 Internal Connectors 1 3 2 7 14 4 12 17 16 5 6 21 9 10 8 15 19 20 18 22 11 13 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) ATX_12V ATX CPU_FAN SYS_FAN1 SYS_FAN2 PWR_FAN FDD IDE1 SATAII0/1/2 /3 /4/5 GSATAII0/1 PWR_LED 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) BATTERY F_PANEL F_AUDIO CD_IN SPDIF_I SPDIF_O F_USB1/F_USB2 COMA LPT CLR_CMOS CI Read the following guidelines before connecting external devices: · First make sure your devices are compliant with the connectors you wish to connect. · Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices. · After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard. Only for GA-P35-DS3R. GA-P35-DS3R/DS3/S3 Motherboard - 22 - 1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start. · To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (400W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system. · The main power connector is compatible with power supplies with 2x10 power connectors. When using a 2x12 power supply, remove the protective cover from the main power connector on the motherboard. Do not insert the power supply cable into pins under the protective cover when using a 2x10 power supply. English ATX_12V : Pin No. 3 1 ATX_12V 4 2 Definition GND GND +12V +12V 1 2 3 4 ATX : 12 24 Pin No. 1 2 3 4 5 6 7 8 9 10 11 Definition 3.3V 3.3V GND +5V GND +5V GND Power Good 5V SB(stand by +5V) +12V +12V (Only for 2x12-pinATX) 3.3V (Only for 2x12-pinATX) Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Definition 3.3V -12V GND PS_ON(soft On/Off) GND GND GND -5V +5V +5V +5V (Only for 2x12-pin ATX) GND (Only for 2x12-pin ATX) 1 13 12 ATX - 23 - Hardware Installation English 3/4/5/6) CPU_FAN/SYS_FAN1/SYS_FAN2/PWR_FAN (Fan Headers) The motherboard has a 4-pin CPU fan header (CPU_FAN), a 3-pin system fan header (SYS_FAN1), a 4-pin system fan header (SYS_FAN2) and a 3-pin power fan header (PWR_FAN). Each fan header supplies a +12V power voltage and possesses a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation. Most fans are designed with colorcoded power connector wires. A red power connector wire indicates a positive connection and requires a +12V voltage. The black connector wire is the ground wire. The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. CPU_FAN (For PCB rev. 2.0): CPU_FAN (For PCB rev. 2.1): 1 CPU_FAN Pin No. 1 2 3 4 1 Definition GND Speed Control Sense +5V / Speed Control Pin No. 1 2 3 4 SYS_FAN2: Definition GND +12V Sense +5V / Speed Control Pin No. 1 2 3 4 Pin No. 1 2 3 Definition GND Speed Control Sense +5V Definition GND +12V Sense SYS_FAN2 SYS_FAN1 / PWR_FAN : 1 SYS_FAN1 / PWR_FAN · Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang. · These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers. 7) FDD (Floppy Disk Drive Connector) This connector is used to connect a floppy disk drive. The types of floppy disk drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB, and 2.88 MB. Before connecting a floppy disk drive, be sure to locate pin 1 of the connector and the floppy disk drive cable. The pin 1 of the cable is typically designated by a stripe of different color. 34 33 2 1 GA-P35-DS3R/DS3/S3 Motherboard - 24 - 8) IDE1 (IDE Connector) The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attaching the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices, remember to set the jumpers and the cabling according to the role of the IDE devices (for example, master or slave). (For information about configuring master/slave settings for the IDE devices, read the instructions from the device manufacturers.) English 39 1 40 2 9) SATAII0/1/2/3/4/5 (SATA 3Gb/s Connectors, Controlled by ICH9R, Orange) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The ICH9R controller supports RAID 0, RAID 1, RAID 5 and RAID 10. Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array. Pin No. Definition 7 SATAII2 SATAII3 1 7 1 7 SATAII4 SATAII5 1 7 7 1 1 7 1 SATAII0 SATAII1 1 2 3 4 5 6 7 GND TXP TXN GND RXN RXP GND Please connect the L-shaped end of the SATA 3Gb/s cable to your SATA hard drive. · A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number. · A RAID 5 configuration requires at least three hard drives. (The total number of hard drives does not have to be an even number.) · A RAID 10 configuration requires at least four hard drives and the total number of hard drives must be an even number. Only for GA-P35-DS3R. - 25 Hardware Installation English 9) SATAII0/1/4/5 (SATA 3Gb/s Connectors, Controlled by ICH9, Orange) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. 7 1 SATAII0 SATAII1 1 7 7 1 SATAII4 SATAII5 1 7 Pin No. 1 2 3 4 5 6 7 Definition GND TXP TXN GND RXN RXP GND 10) GSATAII0/1 (SATA 3Gb/s Connectors, Controlled by GIGABYTE SATA2, Purple) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The GIGABYTE SATA2 controller supports RAID 0 and RAID 1. Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array. Pin No. 1 2 GSATAII0 GSATAII1 1 7 Definition GND TXP TXN GND RXN RXP GND 7 1 3 4 5 6 7 Please connect the L-shaped end of the SATA 3Gb/s cable to your SATA hard drive. A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number. Only for GA-P35-DS3. Only for GA-P35-S3. GA-P35-DS3R/DS3/S3 Motherboard - 26 - 11) PWR_LED (System Power LED Header) This header can be used to connect a system power LED on the chassis to indicate system power status. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5). Pin No. 1 1 English Definition MPD+ MPDMPD- 2 3 System Status LED S0 On S1 S3/S4/S5 Blinking Off 12) BATTERY The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost. You may clear the CMOS values by removing the battery: 1. Turn off your computer and unplug the power cord. 2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.) 3. Replace the battery. 4. Plug in the power cord and restart your computer. · Always turn off your computer and unplug the power cord before replacing the battery. · Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model. · Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model. · When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side should face up). · Used batteries must be handled in accordance with local environmental regulations. - 27 Hardware Installation English 13) F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker and system status indicator on the chassis front panel to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. Message/Power/ Sleep LED Power Switch Speaker Connector MSG+ MSGPW+ PW- SPEAK+ 2 1 RES+ NC HD- SPEAK- 20 19 HD+ IDE Hard Disk Active LED · MSG (Message/Power/Sleep LED, Yellow): Connects to the power status indicator on the chassis front panel. The System Status LED LED is on when the system is operating. The LED keeps blinking when S0 On S1 Blinking the system is in S1 sleep state. The LED is off when the system is in S3/S4/S5 Off S3/S4 sleep state or powered off (S5). · PW (Power Switch, Red): Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for more information). · SPEAK (Speaker, Orange): Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup. If a problem is detected, the BIOS may issue beeps in different patterns to indicate the problem. Refer to Chapter 5, "Troubleshooting," for information about beep codes. · HD (IDE Hard Drive Activity LED, Blue) Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. · RES (Reset Switch, Green): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. · NC (Purple): No connection The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. GA-P35-DS3R/DS3/S3 Motherboard - 28 - RES- Reset Switch 14) F_AUDIO (Front Panel Audio Header) The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it. 1 2 English For HD Front Panel Audio: Pin No. Definition 1 MIC2_L 2 3 4 5 6 7 8 9 10 GND MIC2_R -ACZ_DET LINE2_R GND FAUDIO_JD No Pin LINE2_L GND For AC'97 Front Panel Audio: Pin No. Definition 1 MIC 2 3 4 5 6 7 8 9 10 GND MIC Power NC Line Out (R) NC NC No Pin Line Out (L) NC 9 10 · The front panel audio header supports HD audio by default. If your chassis provides an AC'97 front panel audio module, refer to the instructions on how to activate AC'97 functioninality via the audio software in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio." · When using an AC'97 front panel audio module, you can use either the front or the back panel audio connectors, but not both at the same time. · Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer. 15) CD_IN (CD In Connector) You may connect the audio cable that came with your optical drive to the header. 1 Pin No. 1 2 3 4 Definition CD-L GND GND CD-R - 29 - Hardware Installation English 16) SPDIF_I (S/PDIF In Header) This header supports digital S/PDIF in and can connect to an audio device that supports digital audio out via an optional S/PDIF in cable. For purchasing the optional S/PDIF in cable, please contact the local dealer. 1 Pin No. 1 2 3 Definition Power SPDIFI GND 17) SPDIF_O (S/PDIF Out Header) This header supports digital S/PDIF out and connects a S/PDIF digital audio cable (provided by expansion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time. For information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card. 1 Pin No. 1 2 Definition SPDIFO GND GA-P35-DS3R/DS3/S3 Motherboard - 30 - 18) F_USB1/F_USB2 (USB Headers, Yellow) The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer. Pin No. 9 10 1 2 English Definition Power (5V) Power (5V) USB DXUSB DYUSB DX+ USB DY+ GND GND No Pin NC 1 2 3 4 5 6 7 8 9 10 · Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header. · Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket. 19) COMA (Serial Port Header) The COMA header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer. Pin No. 1 2 3 4 5 6 7 8 9 10 Definition NDCD ANSIN A NSOUT A NDTR AGND NDSR ANRTS ANCTS ANRI ANo Pin 9 1 10 2 - 31 - Hardware Installation English 20) LPT (Parallel Port Header) The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional LPT port cable, please contact the local dealer. 25 1 26 2 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Definition STBAFDPD0 ERRPD1 INITPD2 SLINPD3 GND PD4 GND PD5 Pin No. 14 15 16 17 18 19 20 21 22 23 24 25 26 Definition GND PD6 GND PD7 GND ACKGND BUSY GND PE No Pin SLCT GND 21) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds. Open: Normal Short: Clear CMOS Values · Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. · After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard. · After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations). GA-P35-DS3R/DS3/S3 Motherboard - 32 - 22) CI (Chassis Intrusion Header) This motherboard provides a chassis detection feature that detects if the chassis cover has been removed. This function requires a chassis with chassis intrusion detection design. English 1 Pin No. 1 2 Definition Signal GND - 33 - Hardware Installation English GA-P35-DS3R/DS3/S3 Motherboard - 34 - Chapter 2 BIOS Setup English BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS. To access the BIOS Setup program, press the key during the POST when the power is turned on. To see more advanced BIOS Setup menu options, you can press + in the main menu of the BIOS Setup program. To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility. · Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system. · @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS. For instructions on using the Q-Flash and @BIOS utilities, refer to Chapter 4, "BIOS Update Utilities." · Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction. · BIOS will emit a beep code during the POST. Refer to Chapter 5, "Troubleshooting," for the beep codes description. · It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/clearing CMOS jumper in Chapter 1 for how to clear the CMOS values.) - 35 - BIOS Setup English 2-1 Startup Screen The following screens may appear when the computer boots. A. The LOGO Screen (Default) :POST Screen :BIOS Setup/Q-Flash :XpressRecovery2 :Boot Menu :Qflash Function Keys B. The POST Screen Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-2007, Award Software, Inc. Intel P35 BIOS for P35-DS3R F5c . . . . : BIOS Setup/Q-Flash : XpressRecovery2 : Boot Menu : Qflash 07/05/2007-P35-ICH9-6A79OG07C-00 Motherboard Model BIOS Version Function Keys Function Keys: : POST Screen Press the key to show the BIOS POST screen. To show the BIOS POST screen at system startup, refer to the instructions on the Full Screen LOGO Show item on page 42. : BIOS Setup Press the key to enter BIOS Setup. : Xpress Recovery2 If you have ever entered Xpress Recovery2 to back up hard drive data using the driver disk, the key can be used for subsequent access to XpressRecovery2 during the POST. For more information, refer to Chapter 4, "Xpress Recovery2." : Boot Menu Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up arrow key < > or the down arrow key< > to select the first boot device, then press to accept. To exit Boot Menu, press . The system will directly boot from the device configured in Boot Menu. Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order will still be based on BIOS Setup settings. You can access Boot Menu again to change the first boot device setting as needed. : Q-Flash Press the key to access the Q-Flash utility directly without having to enter BIOS Setup first. GA-P35-DS3R/DS3/S3 Motherboard - 36 - 2-2