User manual GOVIDEO DV2150 - Product Manual

1 Congratulations! Congratulations on your purchase of this DV2150 DVD+VCR. We know you will enjoy this product for many years to come. In case service is required, please take a moment to write down your serial number located on the rear panel of the DVD+VCR: ______________________________________ FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help. Laser Product Notice 1 CLASS 1 LASER PRODUCT 2 DANGER: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3 CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. For DVD Players with 525p, but not 625p, progressive scan output CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE `STANDARD DEFINITION' OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 525p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. CAUTION THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN THE COVER AND DO NOT REPAIR YOURSELF REFER SERVICING TO QUALIFIED PERSONNEL. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO MOISTURE AND ENSURE THAT OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED AWAY FROM THE APPARATUS. Macrovision Notice U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,516,132. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. 2 DVD+VCR User's Guide Table of Contents 1 - Welcome Unpacking / 7 Compatible Media / 7 Front Panel / 8 Front Panel Display / 9 Rear Panel / 10 Remote Control / 11 DVD DVD Setup Menu Overview / 26 About DVD Menu Navigation / 26 Language Settings / 27 Video Settings / 28 Audio Settings / 29 Other DVD Settings / 30 2 - Connections BASIC Antenna/Basic Cable Connections / 13 Cable Box/Satellite Receiver Connections / 14 Basic TV Connections / 15 ADVANCED Enhanced Video Options / 16 Enhanced Audio Options / 17 Rear AV Connections / 18 Front AV Connections / 19 4 - Operations PLAY Basic DVD+VCR Playback / 33 Special DVD Playback Options / 34 Special VCR Playback Options / 35 Other Disc Playback / 36 RECORD Basic Recording / 37 Special Recording Options / 38 Timer Recording / 39 5 - Help Customer Support / 42 Troubleshooting / 42 Product Care & Handling / 44 Technical Specifications / 45 Warranty / 46 Index / 47 3 - Setup VCR VCR Setup Menu Overview / 21 About VCR Menu Navigation / 21 Clock Settings / 22 Channel Settings / 23 Other VCR Settings / 25 ©2004 GoVideo. All rights reserved. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. All other brand and product names are trademarks or registered trademarks of their respective companies. 3 Important Safety Instructions Read Instructions ­ All the safety and operating instructions should be read before the product is operated. 2 Retain Instructions ­ The safety and operating instructions should be retained for future reference. 3 Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. 4 Follow Instructions ­ All operating and use instructions should be followed. 5 Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6 Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7 Water and Moisture ­ Do not use this product near water ­ for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8 Accessories ­ Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9 A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10 Ventilation ­ Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. 1 The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Power Sources ­ This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. Grounding or Polarization ­ This product may be equipped with a polarized alternating­current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Power-Cord Protection ­ Power­supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Protective Attachment Plug ­ The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug. Outdoor Antenna Grounding ­ If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides informa- 11 12 13 14 15 4 DVD+VCR User's Guide Important Safety Instructions tion with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna­discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 21 Damage Requiring Service ­ Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a When the power-supply cord or plug is damaged, b If liquid has been spilled, or objects have fallen into the product, c If the product has been exposed to rain or water, d If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e If the product has been dropped or damaged in any way, and f When the product exhibits a distinct change in performance ­ this indicates a need for service. 22 Replacement Parts ­ When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 23 Safety Check ­ Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24 Wall or Ceiling Mounting ­ The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25 Heat ­ The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 16 Lightning ­ For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power lines surges. 17 Power Lines ­ An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 18 Overloading ­ Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19 Object and Liquid Entry ­ Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20 Servicing ­ Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 5 1 Welcome This Chapter provides a basic introduction to the DVD+VCR, including an overview of the front panel, rear panel, and remote control. 6 DVD+VCR User's Guide Unpacking Check to make sure the following items are included with your DVD+VCR: POWER EJECT DVD 2 5 8 0 TV VIEW 3 6 9 VCR 1 4 7 TRK- TRK+ 100+/P.S CAN CLEAR DISPLAY SETUP CH+ ENTER MENU TITLE CHSEARCH PLAY ZOOM FF SUBTITLE AUDIO REW PREV STOP NEXT REC TV/VCR SKIP SPEED AUTO PLAY REPEAT MARK LAST CH. A-B ANGLE PROG. REPLAY Compatible Media This DVD+VCR will play the following media: · DVD · Audio CD · Video CD/Super Video CD · MP3 files on CD-R/RW · JPEG files on CD-R/RW · DVD-R/RW · DVD+R/RW · VHS tape This DVD+VCR will record on the following media: · VHS tape 1 - Welcome 7 Front Panel Front panel overview: 1 2 3 4 5 6 7 POWER button VCR deck DVD deck AUDIO/VIDEO IN jacks VCR EJECT button RECORD button CHANNEL / buttons 8 9 10 11 12 13 14 Front Panel Display DVD·VCR SELECT button STOP button REW button PLAY/ button FF button DVD EJECT button NOTE: · CHILD LOCK - To lock the DVD+VCR to prevent unwanted operation, press and hold the POWER button on the remote control for 8 seconds. SAFE will flash on the front panel display. Press and hold POWER for 8 seconds to restore normal operation. 8 DVD+VCR User's Guide Front Panel Display Front panel display overview: 1 2 3 4 VHS tape loaded indicator VCR mode indicator DVD mode indicator Disc loaded indicator 5 Record indicator 6 DVD+VCR status indicator 7 Timer Record indicator 1 - Welcome 9 Rear Panel Rear panel overview: DVD ONLY AUDIO OUT R Pb L COAXIAL Y VIDEO S-VIDEO OUT L COMPONENT VIDEO OUT Pr R AUDIO RF DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN DIGITAL AUDIO OUT (TO TV) OUT DVD Playback Only These jacks are for DVD playback only: 1 STEREO AUDIO OUT jacks 2 DIGITAL AUDIO OUT jack 3 COMPONENT VIDEO OUT jacks 4 S-VIDEO OUT jack DVD+VCR Playback These jacks are for both DVD and VCR playback: 5 AUDIO/VIDEO OUT jacks 6 AUDIO/VIDEO IN jacks 7 ANTENNA IN jack 8 ANTENNA OUT jack 10 DVD+VCR User's Guide Remote Control Remote control overview: 1 EJECT button 2 VCR button DVD button TV VIEW button 3 0-9 buttons TRACKING+/- buttons 4 100+/P.SCAN button 5 SETUP button 6 ARROW buttons CH buttons 7 TITLE button 8 SUBTITLE button AUDIO button SEARCH button ZOOM button 9 REW/FF buttons PLAY/PAUSE button 10 PREV/NEXT buttons STOP button 11 RECORD button RECORD SPEED button REPEAT button A-B REPEAT button 12 TV/VCR button AUTO PLAY button MARK button ANGLE button 13 SKIP button REPLAY button LAST CHANNEL button PROGRAM button 14 POWER button 15 CLEAR button 16 DISPLAY button 17 ENTER button 18 DISC MENU button EJECT POWER VCR 1 4 7 DVD 2 5 8 0 TV VIEW 3 6 9 TRK- TRK+ 100+/P.SCAN SETUP CLEAR DISPLAY CH+ ENTER TITLE MENU CHSUBTITLE AUDIO SEARCH REW PLAY ZOOM FF PREV STOP NEXT REC SPEED REPEAT A-B ANGLE TV/VCR AUTO PLAY MARK SKIP REPLAY LAST CH. PROG. NOTE: · Press VCR to control the VCR deck and press DVD to control the DVD deck. · Press TV VIEW to switch among all inputs. 1 - Welcome 11 2 Connections This Chapter shows you how to connect the DVD+VCR to your TV and other home theater components. · · For basic connections, see pages 13-15. For advanced connections, see pages 16-19. 12 DVD+VCR User's Guide Antenna/Basic Cable Connections If you are using an antenna or basic cable TV service: 1 Connect the RF coaxial cable from the antenna or cable wall outlet to the rear panel of the DVD+VCR as shown. 2 Connect the DVD+VCR to your TV; see page 15. DVD ONLY AUDIO OUT R Pb L COAXIAL Y S-VIDEO OUT L COMPONENT VIDEO OUT Pr R DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN AUDIO RF DIGITAL AUDIO OUT VIDEO (TO TV) OUT NOTE: · Do not connect the AC power cord until all other connections have been made. · The DVD+VCR receives broadcast channels 2-69 and cable TV channels 1-125. 2 - Connections 13 Cable Box/Satellite Receiver Connections If you are using a cable box or satellite receiver: 1 Connect an RF cable from the wall outlet to the cable box/receiver. 2 Connect an RF cable from the cable box/receiver to the DVD+VCR. 3 Connect the DVD+VCR to your TV; see page 15. DVD ONLY AUDIO OUT R Pb L COAXIAL Y VIDEO S-VIDEO OUT L COMPONENT VIDEO OUT Pr R AUDIO RF DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN DIGITAL AUDIO OUT (TO TV) OUT NOTE: · With this connection, set the DVD+VCR to channel 3 or 4 and then select channels on the cable box/receiver. For Cable Box Setup options, see page 24. · If your cable box/receiver is equipped with AV Out jacks, use the Rear or Front AV Connections for better picture and sound quality; see pages 18-19. 14 DVD+VCR User's Guide Basic TV Connections If your TV has standard RF or AV inputs: 1 Connect the supplied RF cable from the DVD+VCR to your TV as shown. OR Connect the supplied audio/video cables from the DVD+VCR to your TV as shown. 2 Connect the supplied power cable from the DVD+VCR to a standard wall outlet. 3 Press POWER to turn on the DVD+VCR. 4 Turn on your TV and set it to channel 3 or 4 (for the RF connection) or the appropriate Video input (for the AV connection). · The GoVideo splash screen appears. 5 Continue with Chapter 3 to set up your DVD+VCR. DVD ONLY AUDIO OUT R Pb L COAXIAL Y VIDEO S-VIDEO OUT L COMPONENT VIDEO OUT Pr R AUDIO RF DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN DIGITAL AUDIO OUT (TO TV) OUT NOTE: · If your TV has S-Video or Component Video inputs, see page 16. · To change the RF Out channel to 3 or 4, see page 24. 2 - Connections 15 Enhanced Video Options If your TV has S-Video or Component Video inputs, you can enjoy superior picture quality (DVD playback only). 1 Connect an S-Video cable OR set of Component Video cables from the DVD+VCR to your TV as shown. 2 Select the S-Video or Component Video input on your TV to view the DVD+VCR. · If you use the S-Video Out or Component Video connection, you must set Video Out and Scan Mode in the DVD Setup menu; see page 28. DVD ONLY AUDIO OUT R Pb L COAXIAL Y VIDEO S-VIDEO OUT L COMPONENT VIDEO OUT Pr R AUDIO RF DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN DIGITAL AUDIO OUT (TO TV) OUT NOTE: · Be sure to choose one of the audio connection options on page 17. · The S-Video and Component Video connections are for DVD playback only! 16 DVD+VCR User's Guide Enhanced Audio Options If you have a stereo system or digital audio receiver, you can enjoy superior sound quality. 1 Connect left/right audio cables from the DVD+VCR to your stereo system as shown. OR Connect a digital coaxial cable from the DVD+VCR to your digital audio receiver as shown. 2 Select the appropriate audio input on your stereo or receiver to hear the DVD+VCR. · If you used the coaxial connection, you must set Digital Out in the DVD Setup menu; see page 29. DVD ONLY AUDIO OUT R Pb L COAXIAL Y VIDEO S-VIDEO OUT L COMPONENT VIDEO OUT Pr R AUDIO RF DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN DIGITAL AUDIO OUT (TO TV) OUT NOTE: · If your receiver is equipped with a Dolby Digital and/or DTS decoder your can enjoy 5.1 surround sound playback while watching DVD movies. 2 - Connections 17 Rear AV Connections You can view and record from an external device, such as a VCR, connected to the rear AV inputs. 1 Connect standard audio/video cables from the outputs of the external device to the inputs of the DVD+VCR as shown. 2 Press TV VIEW until Video 1 appears on the screen. DVD ONLY AUDIO OUT R Pb L COAXIAL Y VIDEO S-VIDEO OUT L COMPONENT VIDEO OUT Pr R AUDIO RF DVD + VCR OUT VIDEO VIDEO 1 IN (FROM ANT.) IN DIGITAL AUDIO OUT (TO TV) OUT NOTE: · To record from the external device, see page 38. 18 DVD+VCR User's Guide Front AV Connections You can view and record from an external device, such as a camcorder or video game, connected to the front panel AV inputs. 1 Connect standard audio/video cables from the outputs of the external device to the inputs of the DVD+VCR as shown. 2 Press TV VIEW until Video 2 appears on the screen. NOTE: · To record from the external device, see page 38. 2 - Connections 19 3 Setup This Chapter allows you to customize the DVD+VCR to meet your system requirements and personal preferences. Key settings: · · To set the time and date, see page 22. To search for TV channels, see page 23. 20 DVD+VCR User's Guide VCR Setup Menu Overview The VCR Setup menu allows you to set your preferences for the VCR deck. Choose from these categories: · Clock Settings ­ see page 22 · Channel Settings ­ see page 23-24 · Other VCR Settings ­ see page 25 About VCR Menu Navigation · · · · · · Press VCR to switch to VCR mode. Press SETUP to display the VCR Setup menu. Use the keys to move up and down. Use the keys to move left and right. Press ENTER to make selections. Press SETUP again to go back and exit the Setup menu. EJECT POWER VCR 1 4 7 DVD 2 5 8 0 TV VIEW 3 6 9 TRK- TRK+ 100+/P.SCAN SETUP CLEAR DISPLAY CH+ ENTER MENU TITLE CHSUBTITLE AUDIO SEARCH REW PLAY ZOOM FF PREV STOP NEXT REC SPEED REPEAT A-B ANGLE TV/VCR AUTO PLAY MARK SKIP REPLAY LAST CH. PROG. NOTE: · For DVD Setup, see page 26. 3 - Setup 21 Clock Settings Time & Date Set Allows you to set the date and time. This is necessary if you wish to record TV shows with the timer record feature. 1 Press VCR, then press SETUP. 2 Select Clock Set > Time and Date Set. 3 Set the time and date: · Use to move the cursor. · Use to change each setting. 4 When finished, press SETUP to exit. Auto Clock Set Automatically adjusts the clock for Daylight Saving Time. If you live in an area that does not use Daylight Saving Time, turn this feature off. 1 Press VCR, then press SETUP. 2 Select Clock Set > Auto Clock Set. 3 Choose from the following: On - Adjusts the DVD+VCR's clock automatically for Daylight Saving Time. Off - Ignores Daylight Saving Time. 4 When finished, press SETUP to exit. 22 DVD+VCR User's Guide Channel Settings Auto Channel Search Automatically searches for all available TV stations from antenna or cable TV. If you are using a cable box or satellite receiver, you do not need to run Auto Channel Search. 1 Press VCR, then press SETUP. 2 Select Channel Set > Auto Channel Search. 3 Choose from the following: Cable TV - Select if the DVD+VCR is connected to a cable TV source. Antenna - Select if the DVD+VCR is connected to an antenna. Detect Automatically - Select to have the DVD+VCR detect your signal source automatically. 4 The DVD+VCR searches for all available stations. This may take several minutes to complete. 5 When finished, the DVD+VCR tunes to the lowest channel found. Add/Remove Channels Allows you to manually add or remove channels. 1 Press VCR, then press SETUP. 2 Select Channel Set > Add/Remove Channels. 3 Add or remove channels: · Use to select the desired channel. · Press to add or to remove the channel. 4 When finished, press SETUP to exit. 3 - Setup 23 Channel Settings (continued) Signal Type Specifies whether the DVD+VCR is connected to an antenna or cable TV source. 1 Press VCR, then press SETUP. 2 Select Channel Set > Signal Type. 3 Choose from the following: Antenna - Select if the DVD+VCR is connected to an antenna. Cable - Select if the DVD+VCR is connected to a cable TV source. 4 When finished, press SETUP to exit. Cable Box Setup Allows you to specify the channel or input the DVD+VCR uses to view an external cable box or satellite receiver. 1 Press VCR, then press SETUP. 2 Select Channel Set > Cable Box Setup. 3 Set the cable box channel/input: · Use to select the cable box output channel (usually 3 or 4). · Use the TV VIEW button on the remote to select the Video 1 (rear) or Video 2 (front) input. 4 When finished, press SETUP to exit. RF Output Sets the RF Output Channel (the channel you set on your TV to view the DVD+VCR). 1 Press VCR, then press SETUP. 2 Select Channel Set > RF Output. 3 Set the RF Output Channel to 3 or 4. 4 Set your TV to the channel you selected in step 3. 5 When finished, press SETUP to exit. 24 DVD+VCR User's Guide Other VCR Settings Auto Play Starts VCR playback automatically when you load a tape with its record safety tab removed. 1 Press VCR, then press SETUP. 2 Select Functions > Auto Play. 3 Turn Auto Play on or off. 4 When finished, press SETUP to exit. Auto TV/VCR Controls whether the DVD+VCR switches to VCR mode automatically when turned on. 1 Press VCR, then press SETUP. 2 Select Functions > Auto TV/VCR. 3 Choose from the following: On - Select if you want the DVD+VCR to switch to VCR mode when it is turned on or a tape is inserted. Off - Select if you want the DVD+VCR to remain in TV mode when powered on. 4 When finished, press SETUP to exit. Language Setting Sets the default language for the VCR Setup menu. 1 Press VCR, then press SETUP. 2 Select Language Select. 3 Select your preferred language (English, Spanish, or French). 4 When finished, press SETUP to exit. 3 - Setup 25 DVD Setup Menu Overview The DVD Setup menu allows you to set your preferences for the DVD deck. Choose from these categories: · Language Settings ­ see page 27 · Video Settings ­ see pages 28 · Audio Settings ­ see page 29 · Other Settings ­ see page 30-31 About DVD Menu Navigation · · · · · · · Press DVD to switch to DVD mode. Press STOP to make sure DVD playback is stopped. Press SETUP to display the DVD Setup menu. Use the keys to move up and down. Use the keys to move left and right. Press ENTER to make selections. Press SETUP again to exit the Setup menu. EJECT POWER VCR 1 4 7 DVD 2 5 8 0 TV VIEW 3 6 9 TRK- TRK+ 100+/P.SCAN SETUP CLEAR DISPLAY CH+ ENTER MENU TITLE CHSUBTITLE AUDIO SEARCH REW PLAY ZOOM FF PREV STOP NEXT REC SPEED REPEAT A-B ANGLE TV/VCR AUTO PLAY MARK SKIP REPLAY LAST CH. PROG. NOTE: · For VCR Setup, see page 21. 26 DVD+VCR User's Guide Language Settings On-Screen Display Language Sets the default language for the DVD Setup menu and on-screen displays. 1 In DVD Stop mode, press SETUP. 2 Select Language > OSD Language. 3 Select your preferred OSD language (English, French, or Spanish). Audio Language Sets your preferred language for DVD audio soundtracks. 1 In DVD Stop mode, press SETUP. 2 Select Language > Audio. 3 Select your preferred DVD Audio language. · Select Auto to choose the DVD's default Audio language.