User manual GOVIDEO VR3845A - Product Manual

1 FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures: WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit. · · · · CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner's manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. Reorient or relocate the receiving antenna. Increase the separation between the product and receiver. Connect the product into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. Power Cord Caution Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION: CLASS 2M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED DO NOT STARE INTO THE BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. 2 DVD Recorder+VCR User's Guide Important Safety Instructions 1 2 3 4 5 Read these instructions - All these safety and operating instructions should be read before the product is operated. Keep these instructions - The safety, operating and use instructions should be retained for future reference. Heed all warnings - All warnings on the product and in the operating instructions should be adhered to. Follow all instructions - All operating and use instructions should be followed. Do not use this product near water ­ For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water. Clean only with dry cloth ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/product combination to avoid injury from tip-over. 6 7 13 Unplug this product during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped. 8 9 Congratulations! Congratulations on your purchase of this VR3845 DVD Recorder+VCR. We know you will enjoy this product for many years to come. In case service is required, please take a moment to write down your serial number located on the rear panel of the DVD Recorder+VCR: ______________________________________ 3 Table of Contents 1 - Welcome Unpacking / 7 Compatible Media / 7 Playback and recording / 7 Playback only / 7 Language Settings / 25 On-Screen Display Language / 25 Disc Menu/Audio/Subtitle Languages / 25 Audio Settings / 26 Dolby/DTS/MPEG / 26 Sampling Frequency / 26 Dynamic Range Control / 26 Surround Mode / 26 Front Panel / 8 Front Panel Display / 9 Rear Panel / 10 Remote Control / 11 Parental Control Settings / 27 Parental Control Rating / 27 Changing the Password / 27 Country Code / 27 2 - Connections Antenna/Basic Cable Connections / 13 Cable Box/Satellite Receiver Connections / 14 Basic TV Connections / 15 Enhanced Video Options / 16 Enhanced Audio Options / 17 Rear AV Connections / 18 Front AV Connections / 19 Record Settings / 28 Disc Record Mode / 28 VCR Record Mode / 28 Record Aspect Ratio / 28 DV Record Audio / 28 Auto Chapter Marking / 28 Disc Settings / 29 Initializing Discs / 29 Erasing/Reformatting Discs / 29 Finalizing Discs / 30 Labeling Discs / 30 Protecting Discs / 31 AutoPlay / 31 YourDVD / 31 3 - Setup Setup Menu Overview / 21 Menu Navigation Keys / 21 General Settings / 22 Auto Channel Search / 22 Adding/Deleting Channels / 22 Auto Clock Set / 22 Manual Clock Set / 23 TV Aspect Ratio / 23 Display Mode / 23 Progressive Scan / 23 Playback Control (PBC) / 24 Power Save Mode / 24 Factory Settings / 24 4 - Operations Basic Deck Controls / 33 Basic DVD/VCR Playback / 34 Playing a DVD/VCD / 34 Playing a Tape / 34 Special DVD Playback Options / 35 Special VCR Playback Options / 36 Audio CD/MP3 Playback / 37 Playing Audio CDs or MP3/WMA Files / 37 Special Audio Playback Options / 37 Program Playback / 38 Program Playback with Music CDs / 38 Play Modes during Program Playback / 38 Erasing Tracks from a Program List / 38 4 DVD Recorder+VCR User's Guide JPEG Playback / 39 Viewing JPEG Files / 39 Full Screen Options / 39 Slide Show Options / 39 5 - Help Programming the Remote / 55 Programming the Remote to Control Your TV / 55 About Recording / 40 About Disc Types/Formats / 40 Notes on Recording / 40 Basic Recording / 41 Recording from TV / 41 One-Touch Recording / 41 Watching and Recording / 41 Language Codes / 56 Country Codes / 56 Troubleshooting / 57 Product Care & Handling / 59 Handling Discs / 59 Storing Discs / 59 Cleaning Discs / 59 Moisture Condensation / 59 Other Disc Notes / 59 Recording From External Devices / 42 Recording from a Camcorder/Other Device / 42 Notes on DV Recording / 42 DV Troubleshooting / 42 Timer Recording / 43 Setting a Timer Recording / 43 Timer Recording Notes / 44 Canceling a Timer Recording / 44 Stopping a Timer Recording in Progress / 44 Timer Recording Troubleshooting / 44 Technical Specifications / 60 Other Reference Information / 61 Restrictions on Video Recording / 61 What is `CPRM'? / 61 Copyright Information / 61 Progressive Scan Notice / 61 One Touch Copy / 45 Copying VCR to DVD / 45 Copying DVD to VCR / 45 Warranty / 62 GoVideo Limited Warranty / 62 About Editing / 46 Editing Terminology / 46 Editing Options by Disc Type / 46 Index / 63 Editing Options / 47 Adding Chapter Markers / 47 Changing Thumbnail Images / 47 Making a New Playlist / 48 Adding Titles/Chapters to a Playlist / 48 Deleting Titles/Chapters / 49 Deleting Part of a Title / 49 Renaming a Title / 50 Moving Chapters in a Playlist / 50 Dividing a Title / 51 Merging Two Chapters / 51 Hiding/Showing a Chapter / 52 Protecting a Title / 52 Overwriting a Title / 53 Previewing a Title List Menu / 53 Playing Edited Discs on Other DVD Players / 53 ©2005 GoVideo. All rights reserved. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc. All other brand and product names are trademarks or registered trademarks of their respective companies. 5 1 Welcome This Chapter provides a basic introduction to the DVD Recorder+VCR, including an overview of the front panel, rear panel, and remote control. 6 DVD Recorder+VCR User's Guide Unpacking Check to make sure the following items are included with your DVD Recorder+VCR: Compatible Media The following media can be used in your DVD Recorder+VCR: Playback and recording · · · · · · · · · DVD-RW (VR and Video mode) DVD-R DVD+RW DVD+R VHS tapes DVD Video Video CD Audio CD CD-R/RW and DVD+-R/RW with audio titles, MP3, WMA, or JPEG files NOTE: · This unit is designed for playback of Region 1 encoded DVDs. 1 - Welcome Playback only 7 Front Panel Front panel overview: 1 2 3 4 5 6 7 8 9 10 POWER button DVD deck DVD EJECT button VCR deck VCR EJECT button AUDIO/VIDEO 2 IN jacks S-VIDEO IN jack DV IN jack CHANNEL / buttons COPY button 11 12 13 14 15 16 17 18 19 Front Panel Display (see page 9) Remote Sensor DVD/VCR SELECT button RECORD button PAUSE button STOP button REWIND button PLAYbutton FF button NOTE: · You can lock the front panel buttons to prevent unwanted operation. Simply press LOCK on the remote control to toggle this feature on and off. 8 DVD Recorder+VCR User's Guide Front Panel Display Front panel display overview: DVD SVCD A B REC Hi-Fi ST SAP PRG TTL VR TV CHP TRK DUB When lit, indicates: 1 Current disc type 2 Timer recording in progress 3 Recording in progress 4 Program playback enabled 5 Current title number 6 Disc loaded 7 Tape loaded 8 DVD-RW (VR mode) disc loaded 9 TV mode active 10 11 12 13 14 15 Current chapter/track number Copy in progress Front panel keys locked Tape with Hi-Fi audio playing TV show broadcast in Stereo TV show broadcast in SAP (Secondary Audio Program) mode 16 Current Repeat mode 17 Current DVD Recorder+VCR status 1 - Welcome 9 Rear Panel Rear panel overview: 1 ANTENNA IN jack 2 AC Power cord 3 OPTICAL DIGITAL AUDIO OUT jack 4 S-VIDEO OUT jack 5 AUDIO/VIDEO 1 IN jacks 6 AUDIO/VIDEO OUT jacks 7 COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks 8 AUDIO OUT jacks 9 ANTENNA OUT jack 10 COAXIAL DIGITAL AUDIO OUT jack 10 DVD Recorder+VCR User's Guide Remote Control Remote control overview: 1 POWER button EJECT button 2 DVD button VCR button INPUT button 3 0-9 buttons 4 TITLE button COPY button 5 REW/FF buttons PREV/NEXT buttons 6 PAUSE/STEPbutton PLAYbutton STOP button 7 DISC MENU/LIST button 8 ARROW buttons CH buttons TRACK+/- buttons 9 DISPLAY button 10 LOCK button AUDIO button ZOOM button CLEAR button 11 RECORD button RECORD MODE button TIMER button ADD CHAPTER button 12 PLAY MODE button A-B button THUMBNAIL button TV/VCR button 13 MARKER button SEARCH button 14 TV POWER button TV INPUT button TV CH+/- buttons TV VOLUME+/- buttons 15 SETUP button 16 RETURN button 1 - Welcome 11 2 Connections This Chapter shows you how to connect the DVD Recorder+VCR to your TV and other home theater components. · · For basic connections, see pages 13-15. For advanced connections, see pages 16-19. 12 DVD Recorder+VCR User's Guide Antenna/Basic Cable Connections If you are using an antenna or basic cable TV service: 1 Connect the RF coaxial cable from your antenna or cable wall jack to the rear panel of the DVD Recorder+VCR as shown. 2 Connect the DVD Recorder+VCR to your TV; see page 15. NOTE: · Do not connect the AC power cord until all other connections have been made. · The DVD Recorder+VCR receives broadcast channels 2-69 and cable TV channels 1-125. 2 - Connections 13 Cable Box/Satellite Receiver Connections If you are using a cable box or satellite receiver: 1 Connect an RF cable from the wall jack to the cable box/receiver. 2 Connect an RF cable from the cable box/receiver to the DVD Recorder+VCR. 3 Connect the DVD Recorder+VCR to your TV; see page 15. NOTE: · With this connection, set the DVD Recorder+VCR to channel 3 or 4 and then select channels on the cable box/receiver. · If your cable box/receiver is equipped with AV Out jacks, use the Rear or Front AV Connections for better picture and sound quality; see pages 18-19. 14 DVD Recorder+VCR User's Guide Basic TV Connections If your TV has standard RF or AV inputs: 1 Connect the supplied RF cable from the DVD Recorder+VCR to your TV as shown. OR Connect the supplied audio/video cables from the DVD Recorder+VCR to your TV as shown. 2 Press POWER to turn on the DVD Recorder+VCR. 3 Turn on your TV and set it to channel 3 or 4 (for the RF connection) or the appropriate Video input (for the AV connection). 4 Continue with Chapter 3 to set up your DVD Recorder+VCR. NOTE: · If your TV has S-Video or Component Video inputs, see page 16. · To change the RF Out channel to 3 or 4, first turn off the unit. Then press and hold both of the CH buttons on the front panel for 5 seconds. The selected output channel appears on the front panel display. Tune your TV to this channel. 2 - Connections 15 Enhanced Video Options If your TV has S-Video or Component/Progressive Scan Video inputs, you can enjoy superior picture quality (DVD playback only): 1 Connect an S-Video cable OR set of Component Video cables from the DVD Recorder+VCR to your TV as shown. 2 Select the S-Video or Component Video input on your TV to view the DVD Recorder+VCR. · If you have a Progressive Scan TV, you must activate "Progressive Scan" in the Setup menu; see page 23. NOTE: · Be sure to choose one of the audio connection options on page 17. · If your TV is capable of receiving a Progressive Scan signal, see page 23. 16 DVD Recorder+VCR User's Guide Enhanced Audio Options If you have a stereo system or amplifier/receiver, you can enjoy superior sound quality: 1 Connect left/right audio cables from the DVD Recorder+VCR to your stereo system or analog receiver as shown. OR Connect a digital coaxial or optical cable from the DVD Recorder+VCR to your digital audio receiver as shown. 2 Select the appropriate audio input on your stereo or receiver to hear the DVD Recorder+VCR. · If you used the coaxial or optical connection, you must set the appropriate Audio Settings for your equipment; see page 26. NOTE: · If your receiver is equipped with a Dolby Digital and/or DTS decoder your can enjoy 5.1 surround sound playback while watching DVD movies; see page 26. 2 - Connections 17 Rear AV Connections To view and record from an external device, such as a VCR, connected to the rear AV 1 inputs: 1 Connect standard audio/video cables from the outputs of the external device to the inputs of the DVD Recorder+VCR as shown. 2 Press INPUT until AV1 appears on the screen. NOTE: · To record from the external device, see page 42. 18 DVD Recorder+VCR User's Guide Front AV Connections To view and record from an external device, such as a camcorder or video game, connected to the front panel AV 2 or DV inputs: 1 Connect audio+video cables or S-Video+audio cables from the outputs of the external device to the inputs of the DVD Recorder+VCR as shown. OR Connect a DV cable from the external device to the front panel of the DVD Recorder as shown. 2 Press INPUT until AV2 or DV appears on the screen. NOTE: · To record from the external device, see page 42. · If you use the S-Video In jack on the front panel, the Video In jack is not available. 2 - Connections 19 3 Setup This Chapter allows you to customize the DVD Recorder+VCR to meet your system requirements and personal preferences. 20 DVD Recorder+VCR User's Guide Setup Menu Overview The Setup menu allows you to customize your DVD Recorder+VCR. Choose from these categories: · General Settings ­ see page 22 · Language Settings ­ see page 25 · Audio Settings ­ see page 26 · Parental Lock Settings ­ see page 27 · Record Settings ­ see page 28 · Disc Settings ­ see page 29 Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode TV CATV START Factory Set Prev Menu Navigation Keys POWER Press POWER to turn on the DVD Recorder+VCR. SETUP Press SETUP to display and exit the Setup menu. ARROW KEYS Use the keys to select the desired option. Use the keys to move to the next or previous level. ENTER Press ENTER to confirm your selections. RETURN Press RETURN to exit the Setup menu. 3 - Setup 21 General Settings Auto Channel Search Specifies whether the DVD Recorder+VCR is connected to an antenna or cable TV source, then automatically searches for all available TV stations. 1 Press SETUP. 2 Select "GENERAL" > "Tuning Band" . 3 Choose from the following: TV - Select if you have an antenna. CATV - Select if you have cable TV. 4 Select "Start" . · The DVD Recorder+VCR searches for all available stations. This may take several minutes to complete. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode TV CATV START Factory Set Prev NOTE: · If you receive channels from a cable box or satellite receiver, there is no need to set the Tuning Band or search for channels. Adding/Deleting Channels Allows you to add or delete channels. 1 Press SETUP. 2 Select "GENERAL" > "CH. Add/Del" >"Edit" . 3 Add or delete channels: · Use CH or 0-9 to select the desired channel, then press . · Press ENTER to add or delete the selected channel. Ch. 02 0-9 Input Add Delete Return Auto Clock Set Sets the clock automatically whenever the DVD Recorder+VCR is turned off. 1 Press SETUP. 2 Select "GENERAL" > "Clock Set" > "Auto" . 3 Choose from the following: Time Zone - Set your local time zone to Auto (default), Hawaii, Alaska, Pacific, Mountain Central, or Eastern. Daylight Savings - Set Daylight Saving to Auto (default), OFF, or ON. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set Auto Manual Time Zone Daylight Savings Auto Auto Prev Move Select 22 DVD Recorder+VCR User's Guide General Settings (continued) Manual Clock Set Sets the date and time manually (if Auto Clock is not available in your area). 1 Press SETUP. 2 Select "GENERAL" > "Clock Set" > "Manual" . 3 Set the date and time. · Use to move the cursor. · Use to change each setting. · When finished, press ENTER. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set Auto Manual Date 01 / 01 Year 2005 Time 12 : 00 AM Prev Move Select TV Aspect Ratio Sets your TV Type. 1 Press SETUP. 2 Select "GENERAL" > "TV Aspect" . 3 Choose from the following: 4:3 - Select if you have a standard TV. 16:9 - Select if you have a widescreen TV. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set 4:3 16:9 Prev. Select Display Mode Sets your preferred aspect ratio for DVD movies if you have a standard TV. 1 Press SETUP. 2 Select "GENERAL" > "TV Aspect" . 3 Choose from the following: LetterBox - Select to display widescreen movies with black bars above and below the picture. Fullscreen - Select to crop widescreen movies to fit the screen. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set Letterbox Fullscreen Prev. Select Progressive Scan Activates the Progressive Scan output. 1 Press SETUP. 2 Select "GENERAL" > "Progressive Scan" . 3 Turn Progressive Scan on or off. · Only activate Progressive Scan if your TV is capable of receiving a Progressive Scan signal. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set Prev. Select OFF ON 3 - Setup 23 General Settings (continued) To Cancel Progressive Scan If you enable Progressive Scan accidentally, the picture will be distorted. To reset the unit: 1 Remove any disc or tape in the unit. 2 Press and hold the STOP button for 5 seconds. Playback Control (PBC) PBC stands for Playback Control and refers to special menus and navigation features available on some Video CDs. 1 Press SETUP. 2 Select "GENERAL" > "PBC" . 3 Set PBC to "ON" (Video CDs are played according to the PBC, if available), or "OFF" ( Video CDs are played the same way as Audio CDs). Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set Prev. Select OFF ON Power Save Mode Sets the DVD Recorder+VCR to an economical power saving mode. 1 Press SETUP. 2 Select "GENERAL" > "Power Save Mode" . 3 Turn Power Save Mode on or off. Tuning Band CH. Add/Del Clock Set TV Aspect Display Mode Progressive Scan PBC Power Save Mode Factory Set OFF ON Prev. Select Factory Settings Restores the DVD Recorder+VCR to its original factory settings. 1 Press SETUP. 2 Select "GENERAL" > "Factory Set" > "SET" . 3 Select "Yes" and press ENTER. · All menu settings will be restored to their factory defaults. · Some settings cannot be reset, including the Parental Control, Password, and Area Code settings. Tuning Band CH. Add/Del Clock Set TV Aspect It initializes the Display Mode system status. Continue? Progressive Scan Yes No PBC Power Save Mode Factory Set Prev. Set Select 24 DVD Recorder+VCR User's Guide Language Settings On-Screen Display Language Sets the default language for the Setup menu and On-Screen Displays. 1 Press SETUP. 2 Select "LANGUAGE" > "Display Menu". 3 Select your preferred OSD language (English, Français, Español, or Português). Display Menu Disc Menu Disc Audio Disc Subtitle English Français Español Português Prev Disc Menu/Audio/Subtitle Languages Sets your preferred language for DVD disc menus, audio soundtracks, and subtitles. 1 Press SETUP. 2 Select "LANGUAGE" > "Disc Menu", "Disc Audio" or "Disc Subtitle" , . 3 Select your preferred languages. · For the disc's default language, choose "Original" . · To select other languages, choose "Others" and enter the 4-digit code corresponding to your desired language using the table on page 56. · To disable subtitles, choose "OFF" . Display Menu Disc Menu Disc Audio Disc Subtitle Original English French Japanese Korean Portuguese Spanish Chinese Others - - - Prev 3 - Setup 25 Audio Settings Dolby/DTS/MPEG Sets the format of the digital audio signal from the Coaxial and Optical jacks. 1 Press SETUP. 2 Select "AUDIO" > "Dolby Digital","DTS", or "MPEG" . 3 Choose from the following options: PCM ­ Select if the unit is connected to a 2-channel digital stereo amplifier. Bitstream - Select if the unit is connected to a 5.1 channel amplifier/receiver with a built-in Dolby Digital, DTS, or MPEG decoder. Dolby Digital DTS MPEG Sampling Freq. DRC Surround PCM Bitstream Prev Sampling Frequency Sets the digital output frequency to match the capabilities of your amplifier. 1 Press SETUP. 2 Select "AUDIO" > "Sampling Freq". 3 Choose "48KHz" or "96KHz". · Only select 96kHz if your amplifier is capable of handling 96 kHz signals Dolby Digital DTS MPEG Sampling Freq. DRC Surround 48KHz 96KHz Prev Dynamic Range Control Compresses the dynamic range (DRC) of the audio output--the difference between the loudest and quietest passages--during DVD playback. 1 Press SETUP. 2 Select "AUDIO" > "DRC". 3 Turn DRC on or off. Dolby Digital DTS MPEG Sampling Freq. DRC Surround OFF ON Prev Surround Mode Sets the surround mode. 1 Press SETUP. 2 Select "AUDIO" > "Surround". 3 Choose "Stereo","3D (Virtual Surround)""Dolby Digital" or "DTS" to , , match the capabilities of your audio system. Dolby Digital DTS MPEG Sampling Freq. DRC Surround Stereo 3D Dolby Digital DTS Prev 26 DVD Recorder+VCR User's Guide Parental Control Settings Parental Control Rating Blocks playback of rated DVDs based on their content. Not all discs are rated. 1 Press SETUP. 2 Select "LOCK" > "Rating". 3 Enter your password using the 0-9 keys. · If this is your first visit, you will be prompted to enter and verify your "New Password" . 4 Select the desired Rating from "1(Kids)" to "8(Adult)" then press EN, TER. · Choose "No Limit" to disable the Parental Control feature. · Playback of discs that exceed the set rating will be blocked unless you enter the correct password. Set Password Rating Area Code No Limit 8 (Adult) 7 6 5 4 3 2 1 (Kids) Prev Changing the Password Changes the Parental Control password. 1 Press SETUP. 2 Select "LOCK" > "Set Password" > "Change" . 3 Enter your old password using the 0-9 keys. 4 Enter your new password. 5 Re-enter your new password. Set Password Rating Area Code Change Delete New Password OK Prev 0-9 Input Select Country Code Selects the country whose standards were used to rate the disc. 1 Press SETUP. 2 Select "LOCK" > "Area Code". 3 Enter your password using the 0-9 keys. 4 Enter the desired Country Code from the list on page 56. NOTE: · If you forget your password, press SETUP to display the Setup menu, then press 2-1-0-4-9-9. Select "Yes" and press ENTER. 3 - Setup 27 Record Settings Disc Record Mode Sets the default quality for DVD recording. 1 Press SETUP. 2 Select "RECORD" > "Disc Record Mode". 3 Choose "XP" (1 hr/disc),"SP" (2 hrs/disc), "LP" (4 hrs/disc), or "EP" (6 hrs/disc). Disc Record Mode VCR Record Mode Rec Aspect DV Rec Audio Auto Chapter Disc Record Mode VCR Record Mode Rec Aspect DV Rec Audio Auto Chapter XP SP LP EP SP SLP VCR Record Mode Sets the default quality for VCR recording. 1 Press SETUP. 2 Select "RECORD" > "VCR Record Mode". 3 Choose "SP" (2 hrs/tape), or "SLP" (6 hrs/tape) (T-120 tape). Prev Prev Record Aspect Ratio Sets the aspect ratio for recording. 1 Press SETUP. 2 Select "RECORD" > "Rec Aspect". 3 Choose "4:3" (standard), or "16:9" (widescreen). Disc Record Mode VCR Record Mode Rec Aspect DV Rec Audio Auto Chapter 4:3 16:9 Prev DV Record Audio Sets the audio track to record when dubbing from a DV camcorder connected to the front DV input. 1 Press SETUP. 2 Select "RECORD" > "DV Rec Audio". 3 Choose "Audio 1" to record the original audio, or "Audio 2" to record overdubbed audio. Disc Record Mode VCR Record Mode Rec Aspect DV Rec Audio Auto Chapter Audio 1 Audio 2 Prev Auto Chapter Marking Enables automatic chapter marking at regular intervals during DVD recording. 1 Press SETUP. 2 Select "RECORD" > "Auto Chapter". 3 Choose from the following: OFF ­ Disables auto chapter marking. 5, 10, 15 Min ­ Creates chapters every 5~15 minutes during recording. Disc Record Mode VCR Record Mode Rec Aspect DV Rec Audio Auto Chapter OFF 5 Min 10 Min 15 Min Prev 28 DVD Recorder+VCR User's Guide Disc Settings Initializing Discs Whenever you load a blank recordable disc, the DVD Recorder+VCR will initialize the disc (prepare it for recording): DVD-R - DVD-R discs are always initialized in Video mode. They can be recorded only once. DVD-RW - DVD-RW discs can be initialized in VR Mode or Video Mode. When the "Initialize" menu appears, select "VR Mode" for maximum editing features, or "Video mode" for maximum compatibility with other DVD players. DVD-RW discs can be erased and recorded repeatedly. DVD+R,DVD+RW - When you load a DVD+R and DVD+RW disc, you will be prompted, "Do you want to initialize the disc?" Select "Yes" then press ENTER. DVD+R discs can be recorded once. DVD+RW discs can be erased and recorded repeatedly. NOTE: · Initialization options vary by disc type. These options are presented automatically whenever you insert a blank recordable disc. Erasing/Reformatting Discs To initialize (erase and reformat) a DVDRW or DVD+RW disc: 1 Press SETUP. 2 Select "DISC" > "Initialize" > "Start". 3 Choose from the following: DVD-RW - Select "VR Mode" or "Video Mode" and press ENTER. DVD+RW - Select "Yes" and press ENTER. · All contents will be erased and the disc will be formatted. Initialize Finalize Disc Label Disc Protect AutoPlay YourDVD Start Prev 3 - Setup 29 Disc Settings (continued) Finalizing Discs Finalizing a disc enables it to be played on other DVD players or computers equipped with DVD-ROM drives. DVD+RW discs are finalized automatically. To finalize a DVD+R, DVD-R, or DVD-RW disc: 1 Press SETUP. 2 Select "DISC" > "Finalize". 3 Select "Yes" and press ENTER. · Finalization may take up to 3-4 minutes. Not all finalized discs are compatible with all DVD players. NOTE: · Once you have finalized a DVD-R or DVD+R disc, you cannot edit or record anything else on that disc. · If you finalize a DVD-RW disc, you can record on it again by choosing "Unfinalize" . Initialize Finalize Disc Label Disc Protect AutoPlay YourDVD Finalize Unfinalize Prev Labeling Discs To label your disc (up to 32 characters): 1 Press SETUP. 2 Select "DISC" > "Disc Label" > "Edit". 3 Select the desired characters from the keypad, pressing ENTER after each entry. 4 When finished, select "OK" and press ENTER. · The disc label appears on screen when you press DISC MENU/LIST or DISPLAY. Title 1 Alphabet Capital