Dépliant LU 253106070A Selio EN_UK.fm Page 1 Lundi, 28. juillet 2008 11:02 11 Selio 1. Introduction Dear customer: Thank you for purchasing a DECT Grundig telephone we appreciate your trust in us. This product was manufactured with the utmost care, should you encounter difficulties during its use. We recommend that you refer to this user guide. You can also find information on the following site: http://www.grundig-dect.com For your comfort and safety, we ask that you read the following paragraph carefully: Selio 2. Before you begin Make sure your package includes the items: Base unit, Handset, One battery compartment cover, Handset battery, Telephone line cord, Two rechargeable batteries, AC power supply. Selio Only use the supplied power adapter, connect it to the base socket according to the installation instructions provided in this booklet and the indications on the identification label affixed to it (voltage, current, electric network frequency). As a safety measure, you can use the power adaptors to cut off the 230V current in case of danger. They must be located near to the device, and must be easily accessible. Selio 2.5. Quick guide to handset display icons Signal strength icon (blinking when no signal or the signal strength is weak). Call Handset ringer muted. Received call list (appears when a new call is in the caller list). Selio 4. Calls 4.1. Cordless phone basics 4.1.1. Make a call Ensure that the handset is switched on. 1. 2. 1. 2. Press the Talk key phone icon - OR :Full; : Flat; blinking during charging). If the AUTOMATIC PICKUP function is activated, take the handset off the base station. To end the call, press or place handset on the base station. . , you will hear the dialling tone and the display will show you the 2.3. Handset keys Screen Earpiece Recommendations and safety instructions Your DECT telephone must not be installed in a humid room (wash-up room, bathroom, laundry room, kitchen, etc.) unless it is 1.50 m away from a water point or outside. Your telephone must be operated at temperatures ranging from 5°C and 45°C. Memory. Battery charge state ( Enter the phone number. The number is dialled. In the case of purchasing a pack duo or trio, you will find in addition for each additional handset: A handset charger, One battery compartment cover, Two rechargeable batteries. Navigation key up / Access to dialled number Mute the microphone / Correction / Cancel Talk off / Switch handset on/off Talk on Navigation key down / Access the caller list 4.1.2. Answering a call (Refer to paragraph 8.3 page 12) Access to menu / Validadate 2.1. Digital security system Only use the supplied power adapter, connect it to the base socket according to the installation instructions provided in this booklet and the indications on the identification label affixed to it (voltage, current, electric network frequency). As a precaution, in case of danger, the mains adapters act as a disconnecting mechanism for the 230V power supply. They should be placed near the device and should be easily accessible. This telephone was designed for use on the public switched telephone network (PSTN). In case of a problem you must first contact your reseller. Only use the supplied telephone cord. Telephone cord is to be connected prior to opening the door. For your safety, never place your handset on the base station without its batteries, or without its battery cover. You could get an electric shock. To prevent your handset being damaged, only use approved rechargeable batteries. Never use non rechargeable batteries. Make sure to insert the batteries the right way round in your handset's battery compartment. batteries Your cordless phone uses a security system to provide protection against false ringing, unauthorised access and charges to your phone line. When you place the handset in the base, the unit verifies its security code. After a power cut or replacing batteries, you must leave the handset on the base station for about 20 seconds to reset this code. If the battery charge state displays , this means that your battery level is low and you can no longer use the handset number keypad. In this case, make sure to place the handset back on its base station to recharge the batteries. 1. When the phone rings, press the key to answer the call. - OR - 3. Menu structure phonebook add entry modify entry settings handset tone handset name auto answer base tones language 1. 2. If AUTO TALK MODE is ON, pick up the handset from the base station to answer. Ending a call press key or place the handset in the base station. 2.2. Installing the phone 4.1.3. Handset volume You can adjust the volume of what you hear through the handset at any time by pressing or key. You will hear a beep with each key press. You will hear a double beep when you reach the highest or lowest setting. INT Recall/Flash Internal call delete entry delete all 4.1.4. Caller timer After you press Talk key on the handset, the built-in call timer shows in the display (after 20 seconds) and counts the length of time of the call on minutes and seconds. Activate, deactivate keypad lock + inserting pause In areas where storms are frequent, we recommend that you protect your telephone line using a surge protection device. This equipment does not function in the case of an electric network shutdown: for emergency calls, it is recommended to use another unit during power cuts. The CE marking certifies that the product meets the essential requirements of Directive 1999/5/CE of the European Parliament and of the Council pertaining to microwave radio equipment and telecommunication terminal equipment, for the safety and health of users, for electromagnetic interference. Furthermore, it efficiently uses the frequency spectrum attributed to ground and spatial communication to prevent damaging interference. The declaration of compliance may be looked up on the www.grundig-dect.com site or can be obtained from the following address: Sagem Communications - Customer relations department 4, rue du Petit Albi - 95800 Cergy Saint-Christophe - France 1. 2. 3. 4. 5. 6. Insert the batteries one by one and the right way round as indicated by their polarities in the battery compartment. Put the compartment door back on. Plug the power supply cord into AC outlet and the other end into the power jack on the base bottom. The device gives off an aural signal. Place the handset in the base station to charge for 15 hours prior to first use. if you don't properly charge the phone, battery performance will be compromised. Plug one end of the telephone line cord into the modular wall phone jack and the other end into the jack on the base (as shown in the illustration). Once the batteries are recharged, press key, you can hear dial tone. -1- Selio 4.1.8. Microphone mute function During a call you can switch OFF the microphone. The call is placed on hold. key during - Enable MUTE function: Press the shows "Mute ". Your correspondent will not be able to hear you. - Disable MUTE function: Press the key to continue the call. a call. The display 2. 4.2.3. Accessing the list of calls 1. Press or to access the list of calls made or received. The display shows the recent caller phone number (up to 12 digits). Press the or key through the caller List. 4.1.9. Recall / Flash Press the Company. key to access line transfer offered by PABX or call waiting provided by telephone , the incoming call date and time are displayed. This function only If you press the key works if you have set the date and time on your base station as described in this manual user. If the list is empty, the screen displays "no entries". If the number is already stored in your phonebook, the name of the person in question is displayed. 4.2.4. Calling back a caller 4.1.10. Temporary tone In pulse dialling, you can use temporary tone dialling to temporarily access touch-tone service offered by banks. 1. 2. 3. key after call is answered. Press the Press the number key and follow the voice instructions. After you hang up, the phone automatically returns to dial pulse (rotary) service. 1. 2. 3. Press the Press the Press the key to enter the caller list menu. or key to select a call record. key to dial the number. 2. 1. 2. 3. 4.2.5. Deleting caller list record 1. 2. 3. . Press Press the Press the key to enter the caller list menu. or key to select a call record. 4.1.11. Paging the handset To locate a misplaced handset: Press on the base station, the "paging" icon flashes until you press the Call key to mute the aural signal. the Call/End key 4.2. Calling line identification presentation (CLIP) This CLIP phone stores and displays CLIP information provided by your local telephone company. You must subscribe to CLIP service in order to use this unit. If you have not subscribed to CLIP service or if the caller number is «suppressed», the display shows unknown. Caller ID call waiting is not working in Pulse dialling mode. key. Press To delete the current record : Select "delete entry" using the or key. The selected number is deleted. You will hear a confirmation tone To delete the entire Caller list : Select " delete all " using the or key. A confirmation screen appears : If you do not wish to delete the current record, press To delete the current record, press . . 4. The record or the entire Caller list is deleted. You will hear a confirmation tone. Note! 4.2.1. Caller list CLIP of incoming Call are stored in the CALLER LIST menu. When you enter the CALLER LIST menu, the display will show icon The list contains the numbers of the last 40 contacts call lasted. . 4.2.6. Storing memory from the caller list 1. 2. 3. Press Use Press or or . The list of calls made or received is displayed. to select the desired caller number. key, then select "add entry". press . Note ! If the number is too long (more than 12 digits), the screen will not show the number in full. Press key to go to last number page for CID length. 4. 5. Enter the name of the entry. Press 4.2.2. Display of numbers not available Unavailable: you are not in same area as your contact. withheld: your contact does not want their number to be displayed. to confirm the number. Press The entry is stored in the phonebook. You will hear a confirmation tone. -6- + Your DECT telephone has an inside radio range of about 50 metres and up to 300 metres in open space. The immediate presence of metal parts, (of a television for example), of any electric appliance may result in range reduction. - Worn out batteries must be discarded according to the recycling instructions presented in this booklet. Microphone 4.1.5. Auto talk off Placing the handset in the case cradle while the handset is off the hook (during a call) automatically hangs up the handset. - 2.4. Base Station Power socket Telephone socket advanced set registration de-register clock / alarm date / time alarm alarm tone 4.1.6. Ending a call To end a call press . The timer remains displayed on the screen for 4 seconds. . Base button Pressed briefly: - telephone set paging. Held down (4 seconds minimum): - telephone set registration. pin code phione reset flash time You can, however, return on the screen saver by pressing 4.1.7. Redialling a call The last five numbers you have dialled can be quickly redialled. Redialling from Standby Mode: 1. 2. Press key. The phone number that was last dialled appears on the display. Press the or key to review redial telephone list. (You can select to redial your last five numbers called). Press key to dial out the number. Handset location 3. -2- -3- -4- -5- Selio Selio 5. Using the Multi-Handset capabilities These functions are used for handset management when two or more handsets are registered on the same base. Making a second call while you already on line During a conversation, press then dial the number to be called. The call in process is then put on hold and you can take the second call back. Switching from one call to the other To switch from one call to the other, press then the key . The call in process is then put on hold and you can take the second call back. Ending one of the two calls To end one call and continue with the other, press then the key . The call in process is then ended finally and you take the second call back. To set up a 3-way conference (the 2 calls and yourself) During a conversation, press then the key . You can then talk with the 2 contacts at the same time. To end the 3-way conference, press the red key . Selio Selio 3. Press . . The name entry screen is 5.1. Intercom Call/Intercom 1. Press the INT Using the or key, select "modify entry ". Press displayed with the cursor placed at the end of the line: - The information is accurate. Press - To correct the name, press - Enter the new name and press 4. key. key on the handset. If your installation has two handsets, the second handset is directly called, and "int" followed by the hand ...