User manual HAICOM HI-701BT

4in1 Bluetooth GPS Enable Car Holder ® HI-701 BT Bluetooth® GPS USER MANUAL 1 Introduction: HI-701 BT 4 in 1 car holder is a complete PDA car holder solution with the following functions: 1. Charging and supply power to the PDA 2. Amplifying the PDA sound 3. Making the PDA as a GPS or Bluetooth® GPS enable unit 4. Holding the PDA in car By changing the PDA base connector on the holder, almost any type of PDA can be an independent and complete GPS PDA. HI-701 BT advantages: 1. Almost any type of PDA can be used with the 4 in 1 car holder by using suitable base connector. User can only change the base connector when he changes his PDA. User can also use different kinds of PDA with the same car holder. 2. Taking the GPS signal from the hinged GPS receiver back card from the back of the holder the PDA become a complete GPS enable PDA. The attached GPS receiver can also act as an independent GPS mouse by using different kinds of connecting cables. 3. HI-701 BT + GPS version make the PDA GPS enable wire or wirelessly 1 2 Accessories: Standard Accessories: 1. HI-701 BT 4 in 1 car holder 2. PDA base connector (one type) 3. DC 12V Cigarette lighter power cable (compatible from DC12V to DC24V) 4. Hinged Bluetooth GPS receiver back card 5. Audio cable 6. Suction cup car mount ® 1 2 2 3 3 5 4 6 3 4 Optional Accessories: 1. Different type of PDA base connector 2. CF slot back card 3. PS/II GPS receiver 4. External antenna (for Hinged GPS receiver back card) 5. Mini1394 to PS/II connecting cable 1 2 4 5 3 4 5 5 6 Installations: GPS receiver installation: Slide the inclusive Bluetooth GPS receiver into the back of the car holder so that the PCB golden finger insert and contact properly into the female connector inside. Based on the most powerful and recent SiRF StarIII ultra high sensitive GPS receiver module, the receiver can get satellite signal in very poor reception environment. Beside, the inclusive Bluetooth GPS receiver is come with a hinge design and can be folded from 0 to 180 degree to adjust the best reception angle. lock unlock ® ® LED Indicator (Red) LED off LED flashing LED stay on Receiver switch off GPS Position Fixed GPS Signal searching 6 7 BT / GPS LED indicator LED Indicator (Blue) LED off LED flashing LED stay on Bluetooth® switch off Bluetooth® searching Bluetooth® connected 7 8 GPS Receiver Specification Chipset Interfaces Protocol Baud Rate Max. Update Rate Datum Channel Frequency Hot Start Warm Start Cold Start Reacquisition Tike Position Accuracy Macimum Altitude Maximum velocity Voltage Power consumption Antenna Type External Antenna Connector Dimension LED Indicator Fold: 79 (L) x 60 (W) x 26 (H)mm Unfold: 132 (L) x 60 (W) x 26 (H)mm 3D Positioning (blinking) or Searching GPS (on) SiRF Star III PCB golden finger & Mini-1394 NMEA0183 GGA, GSA, GSV, RMC, GLL 4800, N, 8, 1 1 Hz WGS84 20 channel L1, 1575.42MHz 8 sec. Average 38 sec. Average 48 sec. Average 100 ms 15m 2D RMS, SA off 18,000m 515m/s DC 3.3V+-10% 90mA continuous mode Built-in active antenna MMCX (Optional) 8 9 Bluetooth® Specifications: Bluetooth V1.1 Compliances ® Frequency Range: 2.4 ~ 2.4835 GHz unlicensed ISM band USB/UART/SPI -80 dBm @ 0.1% BER Class 2 -6 dBm ~ +4 dBm 50 ohms 1600hops/sec. 16MHz Up to 723Kb/s -20° C ~ +80° C -30° C ~ +90° C 10 meters (Typical) 65 mA (Typical) Interface: Receiver Sensetivity: Transmitting Power: RF Input Impedance: Frequency hopping: Baseband Crystal OSC: Data Rate: Operating Temperature: Storage Temperature: Transmitting Range: Power Consumption: 9 10 PDA base connector installation: Insert the base connector in the front-lower part of the car holder. Make sure the PDA base connector is compatible to the PDA that you using. 10 11 Goose neck to the holder installation: Place the top of the goose neck to the back of the holder and push up for fixing. Suction cup support installation: Power up: Connect the inclusive power cable one end to the car cigarette lighter and another end to the holder lower-left side's connector jack. 11 12 Install your PDA Editor's Note: Do you need to turn off car ignition to insert PDA? Caution: Turn off the car's ignition before proceeding. When installed in HAICOM 4 in 1 car holder, the battery in your PDA is recharged. Refer to the following to insert your PDA into the cradle: 1. Align the PDA's connector with the connector on the cradle and push down. 2. Press the padded arms firmly against the sides of the PDA to secure it in place. Push in 12 13 Removing your PDA Refer to the following to remove your PDA from the cradle: 1. Push the release button (A) on the side of the cradle to release the padded arms. 2. Lift the PDA straight up to remove it. Caution: Do not twist the PDA as this can cause permanent damage to the connector and/or your PDA. Press 13 14 Connecting to the PDA You can connect the supplied audio cable from your PDA to the to avail of the HAICOM 4 in 1 car holder's built-in speaker. You can connect a GPS antenna to the HAICOM 4 in 1 car holder if you have a GPS-enabled PDA. 1. Connect the supplied audio cable to the HAICOM 4 in 1 car holder (A) and the PDA (B). 2. Connect the PS2 jack from the PS/II GPS receiver to the HAICOM 4 in 1 car holder (C). 3. Position the GPS receiver on the dash or outside the car. Important: If you cannot receive signals from at least three satellites, try relocating the GPS antenna. 14 15 B A C Important Safety Notice: Most GPS software has built-in voice navigation to allow you to keep your eyes on the road while driving. If you need to study the map on your PDA, stop the car and pull into the side of the road first. 15 16 GPS connector pin assignment Ensure the PS2 connector for your GPS receiver conforms to the pin assignments shown below. Color Green White Red Black Function TX RX VCC GND CN1 5 4 2 1 The connector is a 6-pin Mini-DIN (male) with 3.6± 0.1mm wire. Hinge GPS back card pin assignment Vcc 3.3V TX RX GND NC NC 16 17 Hinged Bluetooth GPS receiver back card as a GPS mouse: By connecting different optional connecting cables, the Hinge GPS receiver back card can be all kinds of independent wired GPS receiver solutions. ® 17 18 Get Connected; Installation Guide Laptop PC Installations Run "My Bluetooth Places" and Double Click the "Find Bluetooth Devices" icon ® ® Double Click "BT GPS" Double Click "SPP on BT GPS" 18 19 Key in pin code: "0000" Connected PDA Installations ® Double Click the Bluetooth icon 19