Fully Automatic Washing Machine User's manual This manual is for 50FREE-1 Please read this manual carefully before using. Retain it for future reference. Special number:0030805887A CONTENTS Specification Names of the parts Safety precautions Installation and adjustment Install the water inlet hose Preparation before washing Put in the laundries Usage of the detergent Close the top lid Use the operation buttons Finish washing Disposal after washing Trouble-shooting answer to question Packing list the 2nd cover 1 2 4 6 8 9 9 9 10 13 14 15 16 Specification table Water level/Water quantity (about) Water Injection pressure Rated washing / spinning capacity 0.03MPa ~ 1MPa 5.0kg/5.0kg Packing list Names of the parts Top lid component Control pannel Liquid detergent inlet Quantity User's manual Warranty card Water inlet hose The side of connection between the water inlet hose and the washing machine Inner cove component Detergent box Attachment block (2 pieces) Handle Water inlet valve One One One Filter frame Balance ring Lint filter Inner tub Pulsater Front control board Water absorption cushion Power cord Drain hose frame Drain hose Back cover The side of connection between the jointer of the water inlet hose and the water faucet Cabinet Base frame Adjustable leg film Adjustable leg Fixed leg (3 pieces) Bottom plate One Inside in inner tub of washing machine Meaning and description of the symbols Inner cover component One Inside in inner tub of washing machine Warning sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents. Automatic washing machine One Forbidden sign Contents marked with that symbol are actions forbidden to perform. Performing of those action may result in damage of the machine or influence the personal safety of the users. 1 Safety precautions Please plug the power plug on special receptacle. Be sure to use three-pins power receptacle. Ensure that the earthing prong of the power receptacle is earthed reliably. Use leakage protector if possible. Trouble-shooting answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself. The washing machine must be positioned so that the plug is accessible. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine. Do not plug or pull the power plug with wet hand. Phenomena The digitron displays E0. The drainage cannot work, or is too slow. The digitron displays E1. The reason How to settle Close the top lid. Clean the foreign material. Open and close The top Lid Once. Some minutes later the machine will continue to work The top lid is opened during reserve procedure. Is the drain hose blocked? After long running of pump in the hot weather, power will be cut automatically for safe. Earth It stops running in midway. The digitron displays E2. The top lid is not closed. Are the laundries put slantingly? Is the machine slanting? Is the water tap opened, or is there water supply failure? Is the water inlet valve blocked? Is the water pressure too low? Close the top lid. Reorder the laundries.Close the top lid. Th machine will start running after 10 seconds of being placed horizontally. Open the water tap. Push the start/Pause button once. Clean the water inlet valve then push the start/Pause button once. Push the Start/Pause button once. Do not bend ,extend,twist,bind by force.Do not press or nip it with weight. Keep the pin of the power plug clean,if the power plug is polluted with dust, please wipe with dry cloth carefully. If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or our customer care agent. The safety switch acts, and the spinning cannot work. The digitron displays E3. The water filling does not work, or is slow. After a period of time, the digital displays E4. The digitron displays E6. In case the washing machine is installed on ground with carpet, do not block the ventilation hole with carpet. The ventilation holes at the bottom Carpet The water level sensor is bad. Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position? Please contact the customer care agent. Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position. Do not use water hotter than 50 . The machine does not act Not wash Not spin There's abnormal sound inside the machine Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat? Is the machine slanting? Are the laundries put slantingly in spinning? Are there any foreign materials? Insert the power plug tightly. Close the top lid. Set the laundries flat. Adjust the machine to be even Reorder the laundries and close the top lid. Remove the foreign materials. Fasten the jointer properly. Do not put the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel. Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning and damages to the laundries. The water faucet leaks Is the jointer of water inlet hose loose or awry? Common phenomena Phenomena The spinning is intermittent when it starts. The wash procedure is paused. Explanation Balance the laundries to avoid slanting. The cloth sensor is checking the cloth, it willadd waterafter 48 seconds. Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more. Push the SPIN button , but it doesn't work. The program is setting the drain time. Some time is needed before it starts spinning. It is to avoid splashing during water inlet. The pulsator pauses during water inlet in wash and rinse. There may be some water flowing out of the drain hose in the first use of the machine. It is the water remained in the factory inspection of performance. 2 Disposal after washing After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Clean the detergent box and set it on the control panel seat. 1.The method of dismantle:Push it up aslant and gently. Safety precautions Do not put hand into the rotating tub. It is dangerous even if the rotation speed is slow. Take special care of the children. Keep children away from the washing machine to avoid them climbing on. Do not decompose, repair or alter the machine by yourself. The lint filter must be used during washing. It must be cleaned in time after each using. Lint filter: 1.Push down the spring piece of the top lint filter to 2.The method of install : install it upwards and aslant make the claws out of the filter cover, and then and push it in . pull out the lint filter to get it down. figure1 2.Pull the back of the lint filter, and then you can get down it off the front cover of the lint filter. figure2 3.Sweep the rubbish in the lint filter. 4.Put the back of the lint filter into the front cover . 5.Put the lint filter into filter cover, and make it tight . 6.Make sure the lint filter well installed, or it can influence your use. The back cover of lint filter Up Dismantle Dismantle Do not put any hot or heavy items (such as the kettle with hot water) on the washing machine. Do not wash laundries with volatile materials (such as thinner, petrol etc.). Petro l Benzene Up Dismantle Install Install Install Down The front cover of lint filter Down Figure 1 Figure 2 The handicapped or children without care shall not use the machine. Keep the machine away from direct sunlight and heat source like the heater. The filter screen of the water inlet valve is likely to be blocked by foreign materials and influence the water inlet. Please clean it with brush every two months. If the cabinet is dirty, wipe it with wet cloth Do not flush it directly with water. Wipe it with neutral detergent. Do not wipe it with thinner, petrol, alcohol etc. Petro l Benzene Please keep the lint filter in good condition, and install it to proper position during washing. If the lint filter is lost or damaged,please contact the local after-sales service department of our company. To protect your laundries and washing machine, please take out all of the coins, buttons, sand, hairpin and other foreign materials before washing. 1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose). 2.Do not store water in the washing machine for a long period. Drain the water completely after each using. 3.Be sure to pull off the power plug before maintenance. 4.Hang up the power cord and drain hose. 5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (about 1 hour), then close the top lid. Dismantle Install Please check if the water faucet is open, and if the connection of the water inlet pipe is proper. put up the drain hose It is suggested to use foamless washing powder. Installation and adjustment Please install and adjust the machine according to the requirement of the mannual. It is very important to your security and correct operating the machine. Install the inner cover Outer tube cover 1.Open the top lid of the washing machine. 2.Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove. 3.Firstly insert the inner cover shaft of one side into the corresponding outer tub cover shaft groove, then push the another inner cover shaft into the corresponding outer tub cover shaft groove. Please install to designated position to guarantee there are no dropping or abnormal sound in opening and closing of the inner cover, and the operation shall be smooth. Do not dismount the inner cover component after washing. Outer tube cover shaft groove Inner cover shaft The soak procedure can work in cooperation with automatic programs like standard, carpeting fiber.There is intermittent pulsator stirring during soak. After the machine starts operation, you can only set the program and procedure during washing, and can not make setting in other cases. The function of Softener will be chosen at the same time as sterilize is selected ,when the sterilize is not chosen ,there will be no water flowing into the box for thesoftener preparation. So do not add softener preparation into the box to aviod wasting If the water pressure is too low,in order to wash the closes cleanly,the machine will change from " saving water "to "storing water "automatically. Water level Damping cushion Inner cover components 4 Push the " water level "button,select suitable water level After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth. After defection, it can set the water level automatically. To select other water level, first push the "start/pause" button, then push the "water level" button to set the water level. Air-dry Section · enlarging Push 5. Push the "Air-dry "button,select Air-dry Install the bottom plate After you open the package, please lean the washing machine gently down on soft items ( like the towel cloth, blanket, etc. ). Install the bottom plate to the bottom of the machine, then lift the machine up gently. See to the figure: Bottom plate Back Air-drying could reduce time drying in the sun; fibre could be dress on after ironing 6 Push the "reserve" button to select suitable reserve wash program Reserve Front Soft items After switching on the power, the reserve program is set to off mode automatically. If you need to set the washingprocedure to be finished at reserved time, please push the " reserve " button to set the reserve wash program. Refer to reserve button in Page 11 for selection. Confirm the operation of reserve program Adjust the Installation position The distance that washing machine away from wall should be above 20mm. The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will result in unstable running or stoppage of the machine. Please adjust it with following methods: Confirm it's horizontal: Hang the lead line to check if it is horizontal. When the "reserve" function is activated, the indicator light of the program you have set will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During reserve procedure, push the "reserve" button to display the reserve mode. To change the running program or cancel the ...