Installation Domestic Dishwasher DW12-HFE1 Diagram 3(1) 1(2) N IG LS 2(1) SC LC IS 1 L 4(2) 1 2 3 220-240V~ 50HZ F CnL1 12345678 L 1 4 IAQS M 1 ML 2 C S D-ED 1/2 2 3 2 C CnP3 1 2 3 4 5 6 7 8 CnP2 12 11 10 9 8 7 6 5 4 3 2 1 1 AQS 1 CnP1 6 5 4 3 2 1 SCHEDA DI POTENZA e CONTROLLO ISS R SENSORE TEMPERATURA RELE' GB Code: 0120502384 Safety Hints Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of this appliance. - If the appliance malfunctions turn off water supply to the appliance and disconnect the plug from the wall socket. Refer to the section entitled, "Troubleshooting." If you cannot solve the problem, contact a authorised service centre. - Only specialised personnel are authorised to make repairs. - Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock. - If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. - After installation, the power plug must be accessible. - Rules to follow when using this appliance: * Never touch the dishwasher when barefoot or with wet hands; * We discourage the use of extension cords and multiple sockets; * During installation, the power supply cord must not be excessively or dangerously bent or flattened; * If the appliance is not operating properly, maintenance must be performed, disconnect the appliance from the power supply. Warning: Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open. Check that the detergent receptacle is empty after completion of the wash cycle. To maintain the EFFICIENCY and SAFETY of this appliance,we recommend: - call only service centres authorised by the manufacturer. - always use original Spare Parts Close-up View (Interior) L K V J I H E F J L G A B C D This appliance complies with the following EEC directives: -73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. - The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. - The appliance is not intended for use by young children or inform persons without supervision. - Young children should be supervised to ensure that they do not play with the appliance. - Keep detergents out of the reach of children. - This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; It is also very dangerous to leave it exposed to the rain and elements. - Do not lean or sit on the door when it is open as this could overturn the dishwasher. - Do not touch the heating element during or after a wash cycle. A Cup Rack B Upper Rack C Rack Height Adjustor D Top Spray Arm E Lower Rack F Bottom Spray Arm G Washing Filter H Detergent and Rinse Aid Dispenser I Salt Container Cap J Silverware Basket K Knife Rack L Third Sprayer Close-up View (Control Panel) Specifications Width Depth Height 60 cm 60 cm 85 cm 12 standard place settings 0.03-0.6MPa 220-240V~ 2150W A B C D E ON-OFF Light ON-OFF Button Display Delay Time Delay Select Button Half-load Button F G H I J .1. Low Salt Indicator Light Low Rinse Aid Indicator Light Handle For Opening Door Cycle Select Button Cycle Indicator Light Capacity Mains Water Pressure Power Voltage Total Absorber Power GB GB .2. Salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Detergent and Rinse Aid Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimise and customise the level of salt consumption so that it remains at a minimum. Your local Water Board can supply the degree of hardness of the water in your area. To adjust salt consumption, proceed as follows: Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table." The detergent dispenser is located on the inside panel of the door. Rinse Aid This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the door and should be filled after every 80 wash cycles (or when the rinse aid indicator light comes on for those models with this feature). Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: - Remove the lower rack and then unscrew and remove the cap from the salt container; - If you are filling the container for the first time, fill it with water; - Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container. - Carefully screw the cap back on. Loading the detergent To open the "A" cover on the dispenser, press the "B" button. The detergent for the wash cycle should be poured into the "C" compartment. After the detergent has been placed in the dispenser, close the cover and press down until it clicks in place. Loading the Rinse Aid To open the dispenser, turn the "C" cap in an anti-clockwise direction and then pour in the rinse aid, making sure not to overfill. The amount of rinse aid used for each cycle can be regulated by turning the "F" dose adjustor, located beneath the "C" cap, with a screwdriver. There are 6 different settings; the normal dosage setting is 3. Important C A Proper dosage of the rinse aid improves drying. If drops of water remain on the dishes or spotting occurs, the dosage adjustor should be turned to a higher setting. If the dishes have white streaks, turn the dosage adjustor to a lower setting. - Unscrew the cap from the salt container; - There is a ring on the container with an arrow on it (see figure), If necessary, rotate the ring in an anticlockwise direction from the "-" setting towards the "+" sign, based on the hardness of the water being used. It is recommended that adjustments be made in accordance with the following scheme: B C F C Water Hardness The salt container must be filled when the "low salt" indicator light (located on the control panel) comes on. Salt Autonomy c o n s u m p t i o n (cycles/2kg) (Grams/cycle) To prevent the formation of rust, load the salt just before beginning a wash cycle. Clarke degrees 0 14 dH mmol/l Selector position Note: To facilitate closing the cover, remove any excess detergent on the edges of the dispenser. .3. GB GB .4. Loading the Dishwasher Before placing the dishes in the dishwasher, remove larger food particles to prevent the filter from becoming clogged, which results in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they are soaked before washed. This will eliminate the need for extra wash cycles. Pull out the rack to load the dishwasher. Turning on the Appliance Starting a wash cycle Lower Rack Upper Rack After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ONOFF button (B) located on the control panel. The "A" indicator light will come on. At this point, the appliance is on but you must wait a few seconds before programming the cycle setting. Setting the Wash Cycle with a Delayed Start Time By pressing the "D" button (see close-up view-'Control panel") the start of wash cycle can be delayed for between 1 to 12 hours. Each time the button is pressed, the display (C) will show the number of hours for the delay period. Choose the amount of time desired. After selecting the wash cycle, a short acoustic signal will sound and after a few seconds, the delay time on the display will blink, This indicates that the countdown has begun. How to use the lower rack We recommend that you place the most difficult to clean items on the bottom rack: pots, pans, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm. - Pots, serving bowls, etc. must always be placed face down. - Deep pots should be slanted to allow the water to flow out. - The lower rack features fold down tine rows (see fig.A) so that larger or more pots and pans can be loaded. - The silverware basket can be doubled (see fig.B) so that only one section may be used when the silverware load is light. This also makes space for additional pots and pans and it can also be placed in the upper rack. - Silverware should be placed in the silverware basket with the handles at the bottom; if the rack has side baskets, the spoons should be located individually into the appropriate slots. Especially long utensils should be placed in the horizontal position at the front of the upper rack. Setting and Starting a wash Cycle Select the desired cycle by pressing the selector button (I). Each time the button is pressed, one of the "J" cycle indicator lights will come on in succession. Choose the wash cycle you feel is most Load for 12 Standard Settings appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual. After a few seconds, After the time has lapsed, the cycle will start. the wash cycle has begun and can no longer be changed. If NOTE: necessary, read the paragraph entitled "Cancelling or modifying a During the delay period, it is preferable not to change any of the cycle" settings, If this is necessary, all of the settings must be cancelled Cancelling or modifying a cycle A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). To modify a cycle that is already underway, press the ON/OFF button (B), all of the settings will be cancelled. To set a new cycle, follow the instructions contained in the paragraph entitled "Setting and starting a wash cycle". by pressing the ON/OFF button (B). At this point, all of the steps for "setting the wash cycle with a Delayed Start Time" and "Setting and Starting a wash cycle" must be repeated, following the instructions contained in the corresponding sections. If the door is opened to the unit during the delay period, the countdown will stop. It will begin again when the door is closed. fig.A fig.B All of the wash cycle set to reverse time function, we may in focus start circulate time. How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, plates, small bowls and shallow pans (as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on both sides of the rack itself (see fig.C). Adjust the upper basket to the higher level and you have more space to accommodate those taller pans and trays in the bottom basket. Wash Cycle adjustment Buttons Wash Cycle Program Light The dishwasher is equipped with a LED indicator light (J) that turns on when the appliance is running the wash cycle. 1/2 load Button This button (see "close-up View - Control Panel", letter"E") makes At the end of the wash cycle fig.C fig.D Six beeps will indicate that the wash cycle has finished and the cycle indicator light (J) for the cycle will begin to die out. Turn off the appliance using the ON-OFF button. Turn off the water supply to the appliance and open the door. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and power. It can be used before setting any of the wash cycle, except for the intensive cycle ( if included in the wash cycle table). Please keep in mind that th ...