Operation Manual XQG50-QF800TX(SS) Automatic Drum Washing Machine Table of Contents Before using Names of Parts--------------inside front cover Matters Needing Attention--------------------1-3 Installation----------------------------------------4-5 Control Panel---------------------------------------6 Operational Functions------------------------6-7 During using Program Selection--------------------------------8 Preparation-----------------------------------------9 Washing Methods---------------------------10-11 Maintenance Maintenance--------------------------------------12 Trouble Shooting--------------------------------13 Technical Specification-------------------------14 Wiring Circuit-------------------------------------15 0020503207 Names of Parts Detergent distributor Temperature knob Door Top Operation button program knob Porthole Power supply cable Earth terminal Back plate screw (3) Drainage hose Drainage hose clip Packing bolt (3) Back plate Caution and Warning symbols For your safety, any instructions in this manual with this "Warning" sign shall be strictly followed. For your safety and to prevent damages to the washing machine, any instructions in this manual with this "Stop" sign shall be strictly followed. This diagram may vary slightly with the layout of the washing machine you have just purchased due to technical improvements. Matters Needing Attention Safety 1. A separate earthed socket is required for the power supply. After installation of the washing machine,the power plug should be accessible during the normal wash. 2. Hold the plug and not the electric cable when unplugging the washing machine. 3. Fuses in the power circuit should be rated for 15A. Refer to e washing machine technician or a Haler designated service point for power cable replacement. 4. For your safety, dry hands before touching the washing machine and wear appropriate footwear. 5. Do not use flammable detergent or dry cleaning agent; do not use flammable spray in close vicinity to the washing machine; do not remove or insert the plug in the presence of flammable gas. 6. The door of the washing machine will become hot during the water heating process. Avoid contact with the door during the heating process. For safety, keep children away from the washing machine. 7. Do not allow children play with the packing materials after unpacking. 1 Matters Needing Attention 8. The washing machine must net be used in the open or in area of high moisture as water droptets may form on electrical components,Air dry the appliance if the washing machine components become wet. 9. The washing machine should be place in a well ventilated area maintaing a space between walls or furniture. Wiring Circuit I1 A9 2 b a D.T. IILevel A11 21 A12 a WASH D1 12 DOOR LIGHT 3 b 6 B7 B8 b IPREFILL C7 a FILL C1 C1 b SPIN C2 N 8 E11 EV Pre EV F TM E12 F 11 12 1 5 D7 6 D5 a LOW SPIN 10 13 22 23 B3 4 b SPIN D2 D2 D1 E2 E1 D3 10 /13 b a SPIN WASH E3 10 /13 a SPIN 11 P1 B4 P2 b WASH C4 7 C3 5 TP T M 10. Keep away from heat sources and direct sunlight to prevent plastic and rubber components from aging. 11. During installation, ensure that the electric cable is not trapped by the washing machine and avoid damage to the electric cable. I2 4 PCB 7 D I3 H WASH b 14 / 11 D9 D10 DISTR C11 a DISTR b 8 E9 C9 D11 D12 SPIN C12 IMP. HIGH b a SPIN 9 /12 D4 Use 1. Make sure that the washing machine is securely connected to the water supply, take the necessory precautions or contact the local service center if the connection is poor or there is a water leakage. 2. After turning the power off, turn the program knob clockwise to set washing program. I1: Power Switch I2: No spin Switch I3: Speed Switch MR: Door Lock TM: Timer motor H:Heating Element EV:Water valve P1,P2:Pressure Switch PCB:Speed Module THR:Adjustable Thermastat D:Drain Pump M:Motor 2 15 Technical Specification Model Item Matters Needing Attention 3. Never place heavy objects ,a heating applianceor a water container on the top panel of the washing machine. 4. Do not wash foam rubber or similar sponge materials, XQG50-QF800TX(SS) 220-240V~(50Hz) Power supply Maximum working current Water pressure Washing power Spinning power Max. washing load Spinning speed Washing program Heating power Size (HXDXW) Weight (W) (mm) (kg) (A) (MPa) (W) (W) (kg) (r/min) 10 0.05 P 200 530 5 800/500 13 1800 850x550x595 72 1 5. Before washing, do up zippers, buttons, laces and repair damaged areas,underwear or small articals should be placed in the laundry bag or a pillowslip. Do not wash clothes containing wire frames. 6. Do not open the detergent box during the wash cycle. 7. The door is fitted with a self-lock device and will not open until 2~3 minutes after the washing machine stops. Do not force the door open. Do not open the door when water level reaches the port hole. 8. After washing, turn off the tap to prevent leakage; unplug the washing machine and wipe clean the lower part of the port hole. 9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet. 14 3 Installation As shown in figure1 remove all the packing materials (including the foam base). Trouble shooting The following circumstances do not constitute problems. De net contact the maintenance service until the problem has been confirmed. Problem Possible Cause Poor connection to power supply Power failure Door is not properly closed Machine has not been switched on Water is not turned on Water pressure is less than 0.05MPa The inlet hose is kinked Water supply failure The program knob is not properly set The door is net properly closed Check that the height of the water hose is below 80cm The washing machine fails to operate Fig 1 Check attachments and materials. Washing machine does not fill with water Name Qu'ty Model XQG50QF800TX(SS) Operational manual Quality certificate Water hose Drainage holder Plastic plugs Distributor box 1 1 1 1 3 1 The water supply and drainage do not stop Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during transportation The steps betow should be followed before using the appliance, 1. Remove the rear panel of the washing machine; 2. remove the three packing bolts from the rear panel of the washing machine,the rubber hose and then the shock absorption channel steel; 3. reinstall the back plate; 4. fill the holes left by the packing bolts with plastic plugs. (Attention: the packing bolts and rubber hose should be kept in a safe place for later use) Drainage failure Drainage hose is blocked Drainage hose end is below 100cm above the floor level Strong vibration during spin Some packing fixing bolts removed Washing machine on a uneven surface Operation stops before completion of the wash cycle Water or electricity failure Fig 2 Adjusting the position of the washing machine .There are adjustable feet under the bottom of the washing machine. Before use, the washing machine should be adjusted, as shown in figure 3, so that it is level. Excessive foam in the drum The detergent is not a Iow foam type Excessive detergent has been used Fig 3 4 13 Maintenance 1. Turn of the water and electricity supply after every wash. Open the door to prevent the formation of moisture and odors. If the washing machine is left idle for a long period, drain any remaining water in the machine and replace the drainage hose. 3. Clean the detergent compartment regularly. For the detergent compartment similar to figure (a), raise the compartment slightly to remove and replace after cleaning. 2. Unplug the machine during cleaning and maintenance. Use a soft cloth dampened with soapy liquid to clean the machine case and rubber components. Do not use corrosive or abrasive chemicals or solvents. Installation Connection of water inlet hose and washing machine 1. Place the water inlet hose nut on the connector of the water inlet valve. water inlet hose nut 2. slightly shake the water inlet hose nut to see if it is tightly and properly fixed. connector of water inlet valve 4. Cleaning the Filter (once a month) Press the lower edge of the filter compartment cover to open; (Fig1-2) Remove the filter by turning counterclockwise; (Fig3) Flash clean with running water; Filter replacement is the reverse of removal, Caution: Attention shall be paid to ensure that the filter is replaced correctly to avoid possible leakage. Water drainage hose The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine. Use the water drainage support supplied as an accessory for proper installation of the water drainage hose .fix the water drainage hose support with waterproof sring. Do not use an excessively long water drainage hose and contract the authorized technician if the water drainage hose needs to be extended.the water drainage hose should not be extended more than250cm. (longer extension will result in concurrent water inflow and outflow).The diameter of the extension hose should be the same as the original hose. caution:water drainage hose must not be immersed in water.the original and extension hoses should be tightly connected . fig.1 fig.2 fig.3 Fig (a) Connection of power supply 5. To prevent blockages to the water supply or the ingress of contaminants, clean the water inlet and inlet water filter regularly. 7. If the washing machine is left idle for a long period turn off the water and electricity supply and open the door slightly to prevent the formation of moisture and odors. 6. If the machine is to be moved a distance location, replace the vibration mounting locks which were removed during installation as shown below. Check the following items before connection to the power supply. The socket conforms to the maximun power Ioad(The maximum current Ioad of the socket and power supply cable should not be less than 15A). Power supply voltage conforms to the required value. The power supply socket and the plug of the washing machine compatible,if they are compatible ,Refer to a washing machine technician or a Haier designated service point for power cable replacement. The washing machine should be connected to an earth before use. Supplementary earth cable should not be necessary if the socket is connected to the earth. Supplementary earth cable should be installed on the upper back of the washing machine andconnected to an earth if the power supply socket has no earth connection. Remove the back cover. Replace the rubber plugs. Insert the bolts. Tighten the bolts with the Replace the back spanner provided. cover. 12 100cm 80cm 5 Control Panel C D E F 500 800 Speed bution No spin on off Power Washing Methods 4. Washing temperature Setting Set the washing temperature as required, otherwise, set at position * when heating is not needed, (Maximum temperature for each program is displayed in the section setting) PROGRAMME SETTING (WITH POWER OFF) strong action-cotton 1 pre-wash 2 wash 3 rinse 4 soften 5 spin and nomal action-synthetic 6 pre-wash 7 wash 8 rinse 9 soften and delicate action-wool 10 pre-wash 11 wash 12 rinse 13 spin and XQG50-QF800TX(SS) 5. Selecting the function button Select function buttons as required (refer to the directions printed on the operation panel) ,otherwise keep all the button released. G B A A Washing program Turn the knob clockwise to set the desired wash program. Caution: Turn off the power and turn the program knob clockwise for setting desired wash program. 6. Washing Press the power button and the washing machine will automatically commence the programmed washing process. 7. End B Washing temperature Turn the knob clockwise to set the desired temperature. Temperatures between 30oC-90oC can be setted , Cold wash is selected when the knob is set at *. X 30 Wait 2-3 minutes after the washing process is finished, press the power button again to cut off the power supply. Open the door to take out the laundry. Turn off the tap and unplug the washing machine. Additional information C Detergent distributor Program discription are printed on the handle of the detergent distributor,there are three detergent compartments numbered 1,2,3 Box 1: Pre-washing detergent Box 2: Standard washing - extra-fast washing Box 3: Softening agent, adjusting agent, perfume Besides, there is a separate bleaching powder box 4. In case of bleaching, put this box into compartment 1; remove this box from compartment 1 if pre-washing is chosen. If bleaching is required, place box 4 after the pre-washing is finished. 6 Energy and water saving during wash process 1. Collect clothes for one full wash load, 2. Do not overload the washing machine. 3. Pre-wash heavily soiled clothes. 4. Reduce the amount of detergent or choose fast or minimal washing programs for lightly soiled clothes di ...