User's Guide 920D+(D19BL) COLOR MONITOR Table of Contents Regulatory Information.......................................................................................................................... 2 Introduction Features ................................................................................................................................................... 3 Controls OSD Controls ........................................................................................................................................... 4 OSD Menus .............................................................................................................................................. 5 Power Management Feature................................................................................................................. 8 Standard Signal Table ............................................................................................................................ 8 Specifications .......................................................................................................................................... 9 Pin assignment table D-Sub Mini 15pin connector ...................................................................... 10 Troubleshooting .....................................................................................................................................11 Color Monitor Regulatory Information - FCC Information This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause unacceptable interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced Radio/TV technician for help. Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. - Canadian Notice - Avis Canadien This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. - Energy Star As an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star guidelines for energy efficiency. Notice The information contained in this document is subject to change without notice. 2 Color Monitor Introduction - Features 19-inch (18 inch visual) high performance display color monitor Automatically scans frequencies from - Horizontal frequency: 30 to 96KHz - Vertical frequency: 50 to 160Hz Compatible with VGA, SVGA, VESA, MAC Standards and maximum resolution modes up to 1600 × 1200 Supports VESA flicker free modes including 85Hz refresh rate. On Screen menu fingertip control system to visually select and adjust screen images using control buttons on front panel and on screen menus. Power supply operates on AC 100-240V( ± 10%), 50/60Hz for use all over the world. Power supply operates on AC 220-240V( ± 10%), 50/60Hz for use all over the world.(Europe Version) Equipped with DDC 2B for Plug & Play capability. Equipped with an energy-saving feature. Power management circuit signaled by the computer system, will reduce power consumption when the computer system is not in use. Monitors with nonglare/antistatic screens are compliant with MPR 1990 Emissions standards and meets requirements for CE Marking. TCO : (option) 3 Color Monitor Controls - OSD controls The OSD apears on the screen when you press MENU button. "ON SCREEN MENU" controls include the following extended controls such as Size, Position, Geometry Distortion, Color Temp., Degauss, Moire on & off, Language, OSD-Position, Recall, Cont. & Brt., etc. Accessing OSD Press MENU Button. : Direct Brightness access. + : Direct Contrast access. EXIT from OSD : Press this ( ) button in the main menu and submenu. Additional front controls Power Switch : Turn the monitor power on or off, When the power is on, the LED is lit. 4 Color Monitor Controls - OSD Menu OSD MENU 1. NO OSD 2. MAIN MENU · + Moves to function to choose. · Exit the OSD controls. · MENU : Proceed to the selected menu. 3. BRIGHTNESS · ·+ Proceed to the Brightness menu. Increases or decrease the Brightness. · ·+ · Proceeds to NO.3 Proceeds to NO.4 No meaning CONTROL 4. CONTRAST ·+ Proceed to the Contrast menu. · + Increases or decrease the Contrast position and size Menu control guide 5. H/V-POSITION : exit to the main menu. / + : Refer to / + MENU :Toggle Horizontal and Vertical directly. · After choosing , push MENU button. · MENU : Push this button again & again to change the H/V-position. · : Moves the image left or down. · + : Moves the image right or up. 5 Color Monitor 6. H/V-SIZE · After choosing , push MENU button. · MEUN : Push this button again & again to change the H/V-size. · : Decrease the Horizontal or Vertical size of the image. · + : Increase the Horizontal or Vertical size of the image. The Geometry controls allow you to adjust the curvature or angle of displayed image. · After choosing , push MENU button. · Pincushion : Increase or decrease the curvature of the sides either inward or outward. · Parallelogram : Increase or decrease the tilt of the sides either to the left or right. · Trapezoid : Increase or decreases the bottom of the screen to be the same as the top. · Pin Balance : Increase or decrease the curvature of the sides. · Top Corner : Increase or decreases the curvature of the top sides. · Bottom Corner : Increase or decrease the curvature of the bottom sides. · Rotation : Rotate the entire display to clockwise or counterclockwise. 7. GEOMETRY Geometry Menu control guide : Exit to the main menu. / + : Move the function to choose. MENU : Function to choose. /+ : Increase or decrease the adjustment. 8. MOIRE · After choosing , push MENU button. · Select ON or OFF with / + key. · Select H.MOIRE or v.MOIRE with / + key. · / + : Adjust the Moire Control. 6 Color Monitor 9. LANGUAGE · After choosing , push MENU button. · / + : Select the language. 10. OSD POSITION · After choosing , push MENU button. · MENU : Push this button again & again to change the H/V-OSD position. · : Move the OSD position left or down. · + : Move the OSD position right or up. 11. COLOR TEMP Presetting : Select the desired color setting. The bar is replaced by the color setting choice. " USER, 6500k, 9300k " Color adjustment is available only in USER mode. · / + : Move the bar with or + key to select the user · MENU : Press MENU button to access the sub-menu. · / + : Increcse or decrease the selected color adjustment. · : Exit to the main menu. Controls ICON Function This control removes the build-up of magnetic fields that can affect color purity and convergence. Note : The picture shakes while degaussing is taking place. After internal degaussing the circuitry takes about 30 minutes to regain its maximum power. This controls recalls certain factory setting such as size, position, geometry and color by pressing MENU button. If the monitor is operating in a user mode, this controls has no effect. Degauss Recall Zoom / + : Increase or decrease the Vertical and Horizontal size of image at the same time. 7 Color Monitor Power Management Feature The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling (DPMS) mode of Video Electronics Standard Association(VESA). The power management feature requires that the video card of the computer should support DPMS function. Status Normal mode Stand-by mode Power-Off mode LED Sign Green ON Green Blinking(0.5Sec) Green Blinking(1Sec) Power Consumption 110 Watts Less than 15 W Less than 5 W No image is displayed with Green blinking Monitor is in power saving mode. Use mouse or keyboard to release power saving mode. No image is displayed without LED on. Power cable plug must be pulled out. Check the power plug on monitor and on the wall. "Out of range" displayed on the screen. This message is displayed when the signal from video card exceeds the maximum frequency of the monitor. Readjust resolution and frequency in accordance with the monitor capacity.(Refer to Standard Signal Table) Standard Signal Table Resolution VGA (720 x 400) VGA (640 x 480) VGA (640 x 480) VGA (640 x 480) SVGA (800 x 600) SVGA (800 x 600) XGA XGA (1024 x 768) (1024 x 768) Horizontal Frequency(kHz) 31.469 31.469 37.500 43.269 46.875 53.674 60.023 68.677 79.976 91.146 93.750 Vertical Frequency(Hz) 70.087 59.940 75.000 85.008 75.000 85.061 75.029 84.997 75.025 85.024 75.000 Clock Frequency (MHz) 28.322 25.175 31.500 36.000 49.500 56.250 78.750 94.500 135.000 157.500 202.500 Sync Polarity (H/V) /+ / / / +/+ +/+ +/+ +/+ +/+ +/+ +/+ 8 SXGA (1280 x 1024) SXGA (1280 x 1024) UXGA (1600 x 1200) Color Monitor Specifications ITEM CRT Type CRT Horizontal Dot pitch CRT Surface Input Signal Sync. Video Horizontal Vertical 920D+(D19BL) 19", 90° deflection, FLAT 0.20mm Non-glare, Anti-Reflection & Anti-Static H/V Separate, TTL, positive/negative H/V Composite, TTL, positive/negative RGB Analog (0.7Vp-p), positive 75 Terminated 30KHz~96KHz (Automatically) 50Hz~160Hz (Automatically) 1600Dots x 1200Lines (Non-interlace) 210 MHz Horizontal 350mm, Vertical 262mm 110 Watts AC 100~240V( ± 10%), 50/60Hz ± 3Hz AC 220~240V( ± 10%), 50/60Hz ± 3Hz (Europe Version) D-Sub, 15Pin Connectors(3layer) Unlimited 18.5" (W) x 18.4" (D) x 18.3"(H) / 470mm(W) x 466.5mm(D) x 466mm(H) 22.6" (W) x 24.4" (D) x 22.2"(H) / 573mm(W) x 620mm(D) x 564mm(H) 47.3lbs (21.5kg) 55lbs (25kg) 32°F to 104°F (0°C to 40°C) -4°F to 140°F (-20°C to 60°C) 10% to 85% R.H. Non-condensing Scanning frequency Maximum Resolution Pixel Clock(Max.) Display Size (Standard) Power Consumption(Max.) Power Supply Input Connector Display Colors Dimension Unit Carton Net Gross Operating Storage Weight Temperature Humidity 9 Color Monitor Pin assignment table D-Sub Mini 15pin connector Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Assignment Red Video Green Video z Blue Video Frame Ground Ground Red Video Ground The 15-pin D-Sub connector (male) of the signal cable (IBM Systems) : 1 5 Green Video Ground Blue Video Ground N.C ID Monitor Ground SDA H-Sync V-Sync SCL 11 15 10 6 (15 Pin D-Sub) 10 Color Monitor Troubleshooting No picture Problem Solution Check that the AC cord is correctly connected. Check that the AC socket is live by plugging in another piece of equipment. Power switch and computer power switch should be in position. Ensure that the signal cable is properly connected to the video card or PC. Ensure that the video card is securely seated in the PC. Check the connector for bent or pushed-in pins. Press a key on the keyboard or move the mouse, in case the screen power-saver mode has blanked the screen. Signal cable should be securely attached to the computer. Check the pin assignments and signal timings of the monitor and your video card with respect to recommended timings and pin assignments. Ensure that the video card is securely seated in the PC. Adjust the Contrast and Brightness Controls. Push the Degauss Button once. Caution A minimum interval of 20 minutes should exist before the Degauss Button is used a second time. Do not hold the button down continuously. Image is scrolling or unstable Picture is fuzzy Picture bounces or a waving pattern is present in the picture Move electrical devices that may be causing electrical interference away from the monitor. See the inside front cover of this manual for FCC information. Unshielded audio speakers placed next to the monitor can cause picture distortion. Move the speakers away. Adjust the distortion using the Side Pincushion or Trapezoid Pincushion Balance, Parallel adjustment controls under the on screen menu. Adjust the horizontal and vertical image sizes using the Horizontal and Vertical Size adjustment controls under the on screen menu. Edges of the display image are not square Display image is not centered, too small, or too large 11 ...